PACKAGE CONTENTS
• Magnetic charging cable
• Cable management bumper
• Quick Setup Guide
COMPATIBILITY
Apple® Watch Series 1, 2, 3, 4, and 5
FEATURES
The silicone cable management bumper
stays in place even if it is bumped.
Note: Your magnetic charging cable is slightly
larger than the original Apple® Charging Cable
and may not t in all charging stands designed
for an Apple® Watch magnetic charging cable.
QUICK SETUP GUIDE
Magnetic
Charging Cable
NS-AWCB4CM
WRAPPING THE CABLE
1 Wind the cord around the cable management bumper until the end with the USB
connector is sticking out about an inch.
Note: Make sure that you wrap it tightly.
Before using your new product, please read these instructions to
prevent any damage.
2 Flip the cable management bumper
over and insert the USB connector
into the notch in the back of the
bumper.
Cable
management
bumper
Magnetic
charger
Top view
USB connector
Back viewSide view
Notch
USB connector
Final at size: 13.78 x 3.94 in. (350 × 100 mm)
Final fold size: 2.8 x 3.9 in. (70 × 100 mm)
NS-AWCB4CM_19-0710_QSG_V1_EN_FINAL.ai 1 12/31/2019 10:50:23 AMNS-AWCB4CM_19-0710_QSG_V1_EN_FINAL.ai 1 12/31/2019 10:50:23 AM
USING YOUR MAGNETIC
CHARGING CABLE
1 Pull out the USB connector from the
back of the cable management
bumper and unwind the cord.
2 Plug the USB connector into your charging
source (not included), then set your Apple
watch on top of the charger.
SPECIFICATIONS
• Dimensions (height x diameter):
0.75 in. × 2.75 in. (19 mm × 70 mm)
• Cable length: 4 ft. (121.9 cm)
V1 ENGLISH 190710
LEGAL NOTICES
This device complies with Part 18 of the FCC Rules.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 18 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment o
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit dierent from that to which
the receiver is connected.
This device complies with Part 18 of the FCC Rules. Operation is subject to the
following two conditions:
1) this device may not cause harmful interference and
2) this device must accept any interference received, including interference
that may cause undesired operation of the device.
Any changes or modications in construction of this device which are not
expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment
This device complies with Industry Canada license-exempt RSS
standard(s).
Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference
that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada
applicables aux appareils radio exempts de licence. L'exploitation est
autorisée aux deux conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d'en
compromettre le fonctionnement.
ONE-YEAR LIMITED WARRANTY
Visit www.insigniaproducts.com for details.
CONTACT INSIGNIA:
1-877-467-4289 (U.S. and Canada)
www.insigniaproducts.com
INSIGNIA is a trademark of Best Buy and its aliated companies.
Distributed by Best Buy Purchasing, LLC. 7601 Penn Ave South, Richeld, MN 55423 U.S.A.
©2020 Best Buy. All rights reserved.
NS-AWCB4CM_19-0710_QSG_V1_EN_FINAL.ai 2 12/31/2019 10:50:23 AMNS-AWCB4CM_19-0710_QSG_V1_EN_FINAL.ai 2 12/31/2019 10:50:23 AM
/