Maytag PPH1SD-X Product information

Maytag
Brand
Maytag
Model
PPH1SD-X
Type
Product information
BROWN
G
3 Amp
Fuse
Low or
High Pressure
Switch
(Select Models
Only)
ORANGE
To 208/230 VAC
Power Supply
Contactor
BLUE
BLACK
L1
L2
T1
T2
BLACK
YELLOW
BLACK
C
R
S
R
S
C
BLUE
ORANGE
Outdoor Fan
Motor
Cual
Capacitor
Accessory
Heat Plug
11
2
2
3
3
4
4
5
5
66
7
7
8
8
99
WHITE
RED
WHITE
Plug A
BLACK
RED
BROWN
BLACK
VIOLET
GRAY
Outdoor
Thermostat
(Optional)
Defrost Control Board
Low Voltage Connections
To Indoor
Thermostat
E
R
W2
O
Y
E
DFT
RW2
DF2
DF1
BROWN
TEST
DFT
T2
FOR TEST ONLY
RED
RED
OY
C
T2
T1
RED
Compressor
WHITE
C
Reversing Valve
Solenoid
BLACK
BLACK
YELLOW
On units with
no pressure
switch wire
will connect
Y and T1
BLACK
GREEN
WHITE
Defrost
Sensor
H
C
F
Transformer
WHITE
BLACK
BLACK WHITE
YELLOW BLACK
RED or
RED BLACK
BLUE
WHITE
GRAY
YELLOW or
BLACK or
12345678
1
2
3
5
4
1
2
3
5
4
MOTOR
1
2
3
5
4
6
7
8
9
10
11
12
13
14
15
16
1
2
3
5
4
6
7
8
9
10
11
12
13
14
15
16
1
2
3
5
4
6
7
8
9
10
11
12
13
14
15
16
1
2
3
5
4
6
7
8
9
10
11
12
13
14
15
16
GCO
B1
YWR
B2
R1
WIRE
HARNESS
BLOWER PCB
HUM
HUM
Field Wiring
Factory Wiring
Low Voltage
High Voltage
WIRING DIAGRAM
Convertible Packaged Heat Pump 208/230 Volt Single Phase 60Hz
¢710402a¤
7104020
NOTE: See installation instructions for wiring,
application, and information concerning
accessory Heat Kits and other options.
DEFROST BOARD
OPERATION:
1 CLOSES DURING
DEFROST. RATING:
1 A MAXIMUM
2 OPENS DURING
DEFROST. RATING:
2 HP AT 230 VAC
MAXIMUM
3 CLOSES WHEN “Y” IS
ENERGIZED.
OPEN WHEN “Y” IS
DEENERGIZED.
PROVIDES “OFF” DELAY
TIME OF
5 MIN WHEN “Y” IS
DEENERGIZED.
4 WITH DFT CLOSED AND
“Y” ENERGIZED,
COMPRESSOR RUN
TIME IS ACCUMU-
LATED.
OPENING OF DFT
DURING DEFROST OR
INTERVAL PERIOD
RESETS THE INTERVAL
TO 0.
1. Couper le courant avant de faire
letretien.
2. Employez uniquement des conducteurs
en cuivre.
3. Ne convient pas aux installations de
plus de 150 V a la terre.
NNOTES:
1. Disconnect all power before servicing.
2. For supply connections use copper conductors only.
3. Not suitable on systems that exceed 150 V to ground.
4. If any of the original wire as supplied with the unit must be replaced, it must be
replaced with wiring material having a temperature rating of at least 105°C.
5. For supply wire ampacities and overcurrent protection, see unit rating plate.
  • Page 1 1

Maytag PPH1SD-X Product information

Maytag
Brand
Maytag
Model
PPH1SD-X
Type
Product information
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents