Watchguard Legacy Firebox X Edge Quick start guide

Brand: Watchguard

Model: Legacy Firebox X Edge

Type: Quick start guide

Turn off your computer. If you connect to the Internet using a DSL/cable

modem, disconnect the power from this device.

Disconnect the Ethernet cable that runs from your DSL/cable modem or

other Internet connection to your computer and connect it to the main

WAN port (labeled “WAN 1”) on the Edge.

Connect one end of the green straight-through Ethernet cable supplied

with your Edge to any of the seven, numbered Ethernet ports (labeled 0-6) on

the Edge. Connect the other end to the Ethernet port of your computer.

If you connect to the Internet using a DSL/cable modem, restore the power

to this device. When the indicator lights of the modem stop flashing, the

modem is ready for use.

Attach the AC adapter to the Edge and connect it to a power source. Give

the Edge approximately 30 seconds to start before you turn on your computer.

Start your computer. If you get a message that says your operating system has

no network connection, shut down all equipment and make sure all devices are

connected properly.

Start your Internet browser.

Type https:// in the browser address bar, followed by the IP address of

the Edge trusted interface. The default URL is: https://192.168.111.1.

Press Enter.

Follow the steps in the QuickSetup Wizard to configure your Firebox X Edge.

How do I register?

Write down the serial number on the rear panel of your Firebox X Edge.

Browse to www.watchguard.com/activate

• New Customer? Click Create a User Profile.

• Existing Customer? Login with your LiveSecurity® Service

user name and passphrase.

Your Firebox X Edge includes a 90-day subscription to WatchGuard's

award-winning LiveSecurity Service. LiveSecurity extends your protection

with software updates, emerging threat alerts, expert security articles,

and access to your one-year subscription of managed desktop antivirus

from McAfee®.

For more instructions on activating your LiveSecurity Service, refer to

the User Guide.

Determine how your Internet Service Provider (ISP) issues

your IP address. This changes the way you install your

Firebox X Edge. If necessary, call your ISP to find out

whether your Internet connection supports static

addressing, DHCP, or PPPoE.

Before you begin, make sure that you have a working Internet

connection. Then follow these steps to install your Edge:

Look up the computer’s TCP/IP settings and write them

down for later use. Refer to ”Finding your TCP/IP properties”

in the WatchGuard

Firebox® X Edge User Guide.

Set up your computer to use DHCP. Refer to “Setting your

computer to use DHCP” in the User Guide.

Make sure that your Web browser’s HTTP proxy is disabled.

Refer to “Disabling the HTTP proxy setting” in the User

Guide.

www.watchguard.com

Tech Support:

1-877-232-3531 (U.S. and Canada)

+1-206-613-0456 (all other countries)

www.watchguard.com/support

Thank you for choosing Firebox® X Edge

to protect your data, networks, and computers.

This QuickStart Guide gives you an overview of

how to install and configure your new Edge.

Please read the WatchGuard® Firebox® X Edge

User Guide for detailed installation and config-

uration information.

WatchGuard

LiveSecurity

Service

AC Adapter

Modem

CPU

New Cable

TCP/IP SETTINGS:

_________________________

IP Address

_________________________

Subnet Mask

_________________________

Default Gateway

_________________________

Primary DNS

_________________________

Secondary DNS

_________________________

DNS Domain Suffix

for static addressing

PPPoE SETTINGS:

_________________________

Name

_________________________

Domain

_________________________

Password

FIREBOX

X EDGE

PACKAGE CONTENTS:

Edge

QuickStart

Guide

Straight-Through

Ethernet Cable

User Guide

STEP 5

AC Adapter

Modem

CPU

Edge

Modem

CPU

Internet

Modem

STEP 6

STEPS 7 AND 8

Internet

LiveSecurity®

Activation Card

Edge

STEP 13

Congratulations!

Your Firebox

X Edge is now protecting your

computers from the hazards of the Internet.

Power Clip

Antennae

(Wireless models only)

Wall Mount Plate

(Wireless models only)

WatchGuard

Firebox

X Edge QUICKSTART GUIDE

Part Number WGCE66143_0905

IMPORTANT: You MUST register and install your feature key to enable all

features of your new Firebox X Edge! You can register at

www.watchguard.com/activate. If you do not install your feature key, only

one user can access the Internet or WAN.

System Status

Network

Firebox Users

Administration

Firewall

Logging

WebBlocker

VPN

Wizards

Authenticate User

REFERENCE INFORMATION

Contacting WatchGuard® Technical Support

1-877-232-3531

U.S. End-User Support

1-206-521-8375

U.S. Authorized Reseller Support

+1-206-613-0456

International Support

www.watchguard.com/support

No express or implied warranties are provided herein. All specifications are subject to change

and any expected future products, features or functionality will be provided on an if-and-when

available basis.

Firebox X, the Firebox X logo, and LiveSecurity are either trademarks or registered trademarks

of WatchGuard Technologies, Inc. in the United States and/or other countries. Network Associates,

McAfee and VirusScan are registered trademarks of Network Associates, Inc. and/or its affiliates

in the United States and/or other countries. All other trademarks or tradenames are the property

of their respective owners.

WGCE66143_0905 PART NUMBER 1778-002

Key to Navigation Features and Functions

Shows information about the Edge network and security service settings.

Shows the settings of each network interface and all configured routes.

• External: Configure the Edge external network interface.

• Trusted: Configure the Edge trusted network interface. Select the method the Edge

uses to give IP addresses to computers on the trusted network.

• Optional: Configure the Edge optional network interface. Select the method the Edge

uses to give IP addresses to computers on the optional network.

• WAN Failover: Configure a redundant network connection for the external interface.

• Dynamic DNS: Register the external IP address of the Edge with a dynamic Domain

Name Server (DNS) service.

• Routes: Make a static route to a computer on the trusted or optional networks.

• Network Statistics: Shows information on network performance.

• Wireless: Configure wireless network.

Shows information on active sessions and information about current user accounts.

• Settings: Set the properties that apply to all Edge users.

• New User: Make one or more user profiles and set the degree of access they have to

Edge configuration pages.

• New Group: Configure LDAP managed groups.

• Trusted Hosts: Allow selected users unrestricted Web access.

Shows remote management settings, and the activated upgrades.

• System Security: Select HTTP or HTTPS for configuration pages. You can also select

the HTTP server port.

• WSM Access: Enable remote management with WatchGuard System Manager

(WSM).

• Update: Update the Edge firmware.

• Upgrade: Activate your Edge upgrade options.

• View Configuration: Shows the Edge configuration file in a text format.

Shows incoming and outgoing services, blocked sites, and other firewall settings.

• Incoming: Set your incoming traffic filters

• Outgoing: Set your outgoing traffic filters

• Optional: Configure traffic from trusted to optional networks or disable filtering.

• Blocked Sites: Prevent access to specified network addresses on the external

interface.

• Firewall Options: Set the options to customize your security policy.

Shows current log messages and the system time.

• WatchGuard Log Server: Configure the Edge to send log messages to a WatchGuard

Log Server.

• Syslog Logging: Configure the Edge to send log messages to a Syslog host.

• System Time: Set the time source and time zone for your Edge.

Shows the WebBlocker settings, profiles, allowed sites, and denied sites.

• Settings: Configure the global WebBlocker settings.

• Profiles: Create one or more sets of restrictions to apply to Edge users.

• Allowed Sites: Make a list of Web sites that you can browse to even if WebBlocker

settings block the Web site.

• Denied Sites: Make a list of Web sites that you cannot browse to even if WebBlocker

settings allow the Web site.

• Trusted Hosts: Make a list of computers on the trusted or optional networks that can

bypass WebBlocker.

Shows information on virtual private network (VPN) connections to the Firebox X Edge.

•

Manual VPN: Make a VPN tunnel to an IPSec-compliant device such as a second

Firebox X Edge.

• VPN Keep Alive: Keep a VPN tunnel open when no regular network traffic goes

through it.

• VPN Statistics: Shows important data you can use to monitor your VPN traffic and to

troubleshoot a problem with the VPN configuration.

Shows the wizards available to help you quickly and easily set up important Firebox X Edge

features.

Shows the current login status.

Watchguard Legacy Firebox X Edge Quick start guide

Watchguard Legacy Firebox X Edge Quick start guide

Watchguard Legacy Firebox X Edge Quick start guide

Related papers