Surebonder 9615A-300-3 User guide

Brand: Surebonder

Model: 9615A-300-3

Category: Nail Gun

Type: User guide

Surebonder 9615A-300-3 is a heavy-duty upholstery stapler designed for various upholstery applications, including cornices, auto and marine vinyl trim, cabinet backs, small furniture, screen door repair, molding, and picture frames. It uses 3/8” narrow crown, 22 gauge, upholstery staples in 5/16", 3/8", 1/2", and 9/16", 5/8"leg lengths. The stapler has a quick release magazine for easy drop-in staple loading, a trigger safety lock, and a high impact carrying case. It operates on clean, dry, regulated compressed air, between 60 and 100 psi.

FPC Corporation - 355 Hollow Hill Drive - Wauconda, IL 60084

Phone: (847) 487- 4583 Fax: (847) 487-0174

website: www.surebonder.com e-mail: [email protected]

0613

Model 9615A Upholstery Stapler

WARRANTY

If you have any problems with this tool, please call FPC Corporation

toll-free at 1-800-860-3838 before returning it to the place of purchase.

FPC Corporation warrants this tool to be free from defects in material and

workmanship, under normal conditions of use and when used in accordance with

FPC operating instructions, for a period of 90 days from the date of purchase by

the user. Within the 90 day warranty FPC at its option shall repair or replace tool.

The tool must be returned at the distributor/user expense, either within warranty or

out. Repaired or replaced tools will receive a 60 day warranty. USER MUST BE

USING THE PROPER STAPLES FOR THIS WARRANTY TO BE VALID. WARRANTY IS

VOID IF INCORRECT TYPE OF STAPLES ARE USED.

Visit us at surebonder.com for our full line of products

FPC Corporation - 355 Hollow Hill Drive - Wauconda, IL 60084

Phone: (847) 487- 4583 Fax: (847) 487-0174

website: www.surebonder.com e-mail: [email protected]

Read All Safety Rules and Instructions Carefully

Save this manual for Future Reference

Operating Instructions

SUREBONDER

Uses

300 series - 5/16” thru 5/8” (3/8” narrow crown)

22 gauge upholstery staples

Narrow Crown

For various Upholstery Applications, Cornices, Auto and Marine Vinyl Trim,

Cabinet Backs, Small Furniture, Screen Door Repair, Molding, and Picture Frames

Includes: Allen wrench (2), pneumatic oil

IMPORTANT SAFETY WARNINGS

THE SAFETY WARNINGS BELOW CANNOT COVER ALL POSSIBLE SITUATIONS THAT MAY

OCCUR. THESE BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO PROTECT

AGAINST PERSONAL INJURY TO THE OPERATOR OR OTHER PERSONNEL IN THE AREA, AS

WELL AS DAMAGE TO THE EQUIPMENT. READ AND UNDERSTAND THESE WARNINGS BEFORE

USING EQUIPMENT.

Keep tool away from children, and DO NOT allow children near work area. Do not allow children

or untrained personnel to handle this tool.

DO NOT operate this stapler while tired, or under the influence of drugs, alcohol, or medication

that makes you drowsy.

Never point the stapler at yourself or others - always assume that the stapler is loaded, and

proceed with caution.

Wear safety glasses and ear protection. The tool operator and all personnel in the work area

must wear safety glasses that protect the front and side, to avoid eye injury. Ear plugs should

be worn to avoid hearing damage.

If operator will be working in a situation where overhead work will be done (i.e. on a ladder,

stairs, or scaffolding) a hard hat must be worn.

Never wear loose clothing or jewelry because it can get caught in the moving parts of this tool.

Make sure long hair is covered, to avoid getting it caught in stapler.

Keep the tool pointed away from yourself and others at all times. Keep hands and all body parts

away from rear area of stapler (near air hose) to guard against injury. Keep hands and feet away

from firing head during use.

Keep proper balance and footing at all times - do not over-reach.

Never use oxygen, bottled gas or any type of combustible fuel as a power source - it can cause

an explosion and serious injury.

Do not use near flammable liquids or gases - the stapler sparks during operation, and could

cause an explosion and serious injury.

Use an air hose that will withstand at least 150 psi, OR 150% of the maximum pressure of the

compressor.

Never connect this tool to compressed air if the pressure could exceed 200 psi, as the stapler

could burst. Use only clean, dry, regulated compressed air, with pressure not exceeding 100 psi.

Disconnect stapler from air supply before loading staples, to prevent a staple being fired during

connection to air hose.

Do not use a non-relieving coupler with this stapler - if used, the stapler could remain charged

with air after disconnecting, and would still be able to drive a staple even after being

disconnected. The stapler and air hose must have a coupling so that all pressure is removed

from the stapler when the coupling is disconnected.

Do not depress the trigger while loading staples - accidental firing of a staple can occur. Keep

your fingers away from the trigger when not firing staples. Always keep the stapler pointed

downward during loading.

Do not use an air hose that is too long - tool operator can trip over it. Make sure all connections

are tight.

Disconnect air hose from stapler

- before performing maintenance or loading staples

- clearing a staple jam

- when tool is not in use

- when moving it to another location

- when handing stapler to another person

(WARNINGS continued next page)

Dia. Part

Description Description No. No. Description Price

SEAL,AIR SCREW 5*20 2 9615A-2

EXHAUST COVER

not available

O-RING 11.8*2.4 COMPRESSION SPRING 5 9615A-5 CYLINDER CAP not available

O-RING 26.6*2.4 WASHER 7.3*4.7*0.8 9 9615A-9 HEAD VALVE PISTON not available

O-RING 21.3*3 SPRING 10 9615A-10 PISTON STOPPER not available

O-RING 35*2 SPRING 13 9615A-13 COLLAR not available

BUMPER COMPRESSION SPRING 15 9615A-15 CYLINDER not available

GASKET STEP PIN 18 9615A-18 BODY not available

NOZZLE STEP PIN 21 9615A-21 TRIGGER VALVE HEAD not available

SEAL,AIR SPRING 22 9615A-22 TRIGGER VALVE STEM not available

O-RING 3.5*1.5 SCREW 4*16 24 9615A-24 TRIGGER VALVE GUIDE not available

O-RING 11*1.9 SPACER 28 9615A-28 TRIGGER GUIDE not available

E-RING 2.5 SCREW 4*8 31 9615A-31 TRIGGER not available

O-RING 38.5*3.1 SCREW 4*10 34 9615A-34 TAIL COVER not available

O-RING 17.3*3 EXTENSION SPRING 35 9615A-35 AIR PLUG not available

36 9615A-36 CLICK LEVER not available

44 9615A-44 GRIP not available

46 9615A-46 DRIVER GUIDE not available

Description 49 9615A-49 STOPPER not available

PISTON SET 50 9615A-50 UPPER MAGAZINE not available

53 9615A-53 PUSHER not available

54 9615A-54 MAGAZINE ASSEMBLY not available

9615A-400 SEAL KIT www.surebonder.com

9615A-410 DRIVE PIN KIT www.surebonder.com

9615A-420 FASTENER KIT www.surebonder.com

No.

Diagram Diagram

No.

4 1

6 3

PARTS

Includes: Includes: SOLD SEPERATELY

Seal Kit #9615A-400 Fastener Kit #9615A-420

23 45

16 29

19 37

20 38

Drive Pin Kit #9615A-410

Includes:

12 26

17 32

25 47

30 48

33 51

No.

Kit

Prices

Diagram

SAFETYLOCK

Buypartsat:www.surebonder.com

9615APartsList

Preparing for Use

If stapler has been stored in a cold environment, bring it to a warm area and allow it to warm up

before using.

Loading Staples

- Make sure stapler is disconnected from air supply.

- Make sure trigger safety lock is in locked position (Fig. 1).

- Only use the proper size and type of staple with this stapler, as specified under "Staples".

- Depress the track release lever to release the spring-loaded staple magazine; slide the magazine

out (back) as far as it will go.

TO LOAD STAPLES - TURN STAPLER UPSIDE DOWN,

insert a full strip of staples into the staple

magazine with the staple points facing up (Fig. 2). Slide the staple magazine closed until the track

release lever clicks back in place. (Closing the staple magazine while staples are loaded engages

the spring-load mechanism, so it will take slightly more pressure to slide the magazine closed).

Unlock Trigger Safety after Loading Staples to begin Stapling

- Be sure staples are loaded correctly into stapler (Fig. 2).

- Grip the body of the stapler firmly, make sure the

nosepiece is placed securely against the work surface.

- Pull down trigger safety lock to unlocked position (Fig. 3)

and pull the trigger to drive a staple.

- Remove finger from the trigger.

- To drive another staple, move the stapler to next area

on work surface to be stapled, and repeat these steps.

After Stapling

- Disconnect the air hose from the stapler.

- Remove all staples from the staple magazine of the stapler.

- Place several drops of oil (included in case) into the air inlet.

- Shut off air compressor and drain any moisture from the compressor tank.

- Drain the air line filter; clean the filter element,

then blow air in opposite direction to remove any

dirt/debris.

- Keep lubricator filled with oil (included in case).

Clearing Staple Jams

- Disconnect the air hose from the stapler.

- Unscrew 4 nosepiece screws to release nosepiece (Fig. 4).

- Clean and carefully remove staple strip from staple magazine.

- Remove any remaining loose staples from inside the

staple magazine, using pliers to grasp the staples, if necessary.

- Once jammed staples have been removed, reload stapler.

APPLICATIONS

Including, but not limited to: various upholstery applications, trim, frames, cornices, etc.

FEATURES

- Rubber hand grip for comfort

- Quick release magazine for easy drop-in staple loading

- Trigger safety lock

- High impact carrying case

STAPLES

The Surebonder 9615A Upholstery Stapler is designed to use 3/8”narrow crown, 22 gauge,

upholstery staple in 5/16", 3/8", 1/2", and 9/16", 5/8”leg lengths.

For best results use:

Surebonder 300 Series Narrow Crown Upholstery Staples.

AIR SUPPLY

This stapler is designed to operate on clean, dry, regulated compressed air, between 60 and

100 psi. (Do not exceed 100 psi). It is preferable to include an air filter, pressure regulator,

and automatic oiler within 15 feet of the tool, if possible.

An air filter is needed to remove contaminates and moisture that are contained in compressed

air; filtering will significantly prolong the life of the tool. If an automatic oiler is not installed,

place 5 to 6 drops of oil into the tool's air inlet at the beginning of each work day and

2 to 3 drops of oil after using approximately 3 strips of staples.

The staple gun comes factory-equipped with a male quick connector. The staple gun must

always be connected to the air supply with a coupling that removes all pressure when it is

disconnected.

NOTE: all components used with this staple gun (air hose, connectors, regulators,

filters, etc) must be rated at 150 psi, OR 150% of the maximum compressor

potential, whichever is higher. Do not connect this staple gun to a system with

maximum potential air pressure greater than 200 psi.

100

120

140

160

Lubricator Regulator Filter

To compressor

To Air Tool

Quick Connector Quick Coupler

Fig. 2: LOADING STAPLES: Turn stapler upside down, insert a full strip of

staples into staple magazine with staple points facing up. (see diagram)

Insert staple points facing up!

Fig. 2 (Step 2)

Unscrew 4 nosepiece screws

to release nosepiece



Fig. 4

Keep Trigger safety locked in locked

position when loading staples.



Trigger safety lock in unlocked position 

Fig. 1 (Step 1)

Fig. 3 (Step 3)

pull down to

unlock

trigger safety

and begin

stapling!

DO NOT place finger on trigger when disconnecting air hose - the stapler could fire when

reconnected to the air supply.

Carry tool by the handle only, not by the air hose.

Do not drive staples close to the edge of the workpiece. It could split, allowing a staple to fly or

ricochet and causing personal injury. Do not try to drive staples at too steep an angle. Make sure

stapler is held firmly during firing to minimize recoil.

Do not drive a staple into very hard material, thin material, or on top of an existing staple - the

staple could ricochet, causing personal injury.

Never use the stapler if it is leaking air, stapler has missing or damaged parts, or requires repair.

Make sure all screws and caps are securely tightened.

Inspect the stapler before each use to insure that the trigger and spring are operating properly.

Lock the stapler in a clean, dry storage area between uses.

Only use parts, staples, and accessories supplied or recommended by FPC Corporation.

Unauthorized parts or fasteners can lead to malfunction and serious injury. Only personnel trained

by FPC Corporation, the distributor, or the employer shall repair the stapler. Do not modify this

tool without the written approval of FPC Corporation.

Manufacturer assumes no responsibility for consequential or indirect damages from the use of

this product.

Save this manual and have it available for tool operators reference!

Specifications

Overall Dimensions: 9” x 5.75” x 1.75"

Operating Pressure: 60 - 100 psi (do not exceed 100 psi)

Magazine Capacity: 100 staples

Air Inlet Size: 3/8” npt

Weight of Tool: 1.90 lbs.

Staple Specs:

300 series, 3/8” narrow crown, 22 gauge upholstery staples,

5/16", 3/8", 1/2", 9/16", 5/8” leg lengths

Track Release

1/4” Male Quick

Release Connector

Trigger

Trigger Safety Lock

Staple Magazine

Rubber Grip

! WARNING

WARNING: This product contains chemicals known to the State of California to cause cancer, birth

defects,

or other reproductive harm. (This warning is given in compliance with California’s Proposition 65.)

Nosepiece

Surebonder 9615A-300-3 User guide

Brand: Surebonder

Model: 9615A-300-3

Category: Nail Gun

Type: User guide

Download PDF

report

Surebonder 9615A-300-3 User guide

Surebonder 9615A-300-3 User guide

Related papers

Other documents