Fantech PROPLUS-L Installation guide

Installation Manual

Manuel d’opération

Manual de Instalación

Item #: 153509

Rev Date: 2019-07-11

ProPLUS(-L) Series

Bathroom Exhaust Fan with Motion and Humidity Sensors

Ventilateur de salle de bain avec capteurs de mouvement et d'humidité

Extractor de baño con sensores de movimiento y humeda

Package includes:

Fantech Exhaust Fan, 1 pc

EZ Mounting Bracket, 1 pc

Mounting screws, 7 pcs

L'ensemble comprend:

Ventilateur extracteur ou ventilateur à éclairage

Fantech, 1 pc

Supports de fixation, 1 pc

Vis de fixation, 7 pcs

El paquete incluye:

Extractor de aire o un extractor con luces

Fantech, 1 pc

Ménsulas de montaje, 1 pc

Tornillos de montaje, 7 pc

Technical / Customer Support:

United States Tel.: 800 747 1762

Canada Tel.: 1 800 565 3548

Mexico Tel.: +52 55 9126 3455

2

fantech

Note Warning /

Important

note

Information Technical

information

Practical tip

1. Use this unit in the manner intended by the

manufacturer. If you have any questions,

please contact the manufacturer.

2. Before servicing or cleaning unit, switch

power off at service panel and lock the

service disconnecting means to prevent

power from being switched on accidentally.

When the service disconnecting means

cannot be locked, securely fasten a

prominent warning device, such as a tag,

to the service panel.

3. Installation work and electrical wiring must

be done by qualified person(s) in

accordance with all applicable codes and

standards, including fire-rated

construction.

4. Sufficient air is needed for proper

combustion and exhausting of gases

through the flue (chimney) of fuel burning

equipment to prevent back drafting. Follow

the heating equipment manufacturer’s

guideline and safety standards such as

those published by the National Fire

Protection Association (NFPA), and the

American Society for Heating, Refrigeration

and Air Conditioning Engineers (ASHRAE),

and the local code authorities.

5. When cutting or drilling into wall or ceiling,

do not damage electrical wiring and other

hidden utilities.

6. Ducted fans must always be vented to the

outdoors.

7. If this unit is to be installed over a tub or

shower, it must be marked as appropriate

for the application and be connected to a

GFCI (Ground Fault Circuit Interrupter) –

protected branch circuit.

8. NEVER place a switch where it can be

reached from a tub or shower.

9. This fan must be properly grounded.

10. Do not use in the cooking area (Figure. 1).

11. Do not block the air intakes or exhaust.

12. Power supply wiring is to be No. 14 AWG

wire or larger (suitable for at least 90°C

(190°F) ).

13. Not for use outdoors.

14. The fan must not be installed in a ceiling

with an “R” rating greater than 40.

15. The fan is type IC (Inherently Protected).

16. To reduce the risk of injury, install the fan

at least 7 feet (2.1m) above the floor.

17. Acceptable for use over a shower or tub

when installed in a GFCI protected branch

circuit.

18. The fan should not be turned on or off

rapidly.

19. Do not clean the fan with corrosive

chemicals or water in excess of 60° C

(140° F).

20. If the fan is not operating properly, shut

the power off immediately, and have a

certified installer inspect it and have it

serviced as required.

21. Fan must be mounted to structural

members that are strong enough to

support the fan’s weight.

22. Do not allow foreign objects to enter the

fan; this could result in electric shock or

fan damage.

Caution:

1. For general ventilating use only. Do not use

to exhaust hazardous or explosive

materials and vapors.

2. This product is designed for installation in

flat ceilings only. Do not install it in a

sloping ceiling or in a wall.

3. To avoid motor bearing damage and noisy

unbalanced impellers keep construction

material / dust from entering the fan.

4. Please read specification label on the

product for further information and

requirements.

Figure 1

Cooking area

Do not install above or

inside this area

45°45°

Floor

Cooking

Equipment

Read and Save these instructions for future reference.

Before installation, to reduce the risk of fire, electric shock, or injury to persons, observe the following:

Page is loading ...

5

fantech

Dimensions • Dimensiones

Specifications

Fan Speciﬁcations

Model Power Consumption (W) Airﬂow (CFM)

Power Motor

ProPLUS 120V/60 Hz 25 80 / 90 / 110 / 140

ProPLUS -L 120V/60 Hz 30 80 / 90 / 110 / 140

Spéciﬁcation du ventilateur

Modèle Consommation d'énergie (W) Débit d'air (pi

3

/min)

Puissance Moteur

ProPLUS 120V/60 Hz 25 80 / 90 / 110 / 140

ProPLUS -L 120V/60 Hz 30 80 / 90 / 110 / 140

Especiﬁcaciones del extractor

Modelo Consumo de energía (W) Flujo de aire (CFM)

Alimentación Motor

ProPLUS 120V/60 Hz 25 80 / 90 / 110 / 140

ProPLUS -L 120V/60 Hz 30 80 / 90 / 110 / 140

Spécifications

Especificaciones

7-5/8"

11-3/8"

10-1/2"

13"

13-3/4"

289 mm

267 mm

350 mm

330 mm

194 mm

11-3/8"

10-1/2"

7-5/8"

13"

13-3/4"

289 mm

267 mm

330 mm

350 mm

194 mm

6

fantech

Assembly

The ducting from this fan to the outside of the building has a strong effect on the air ow, noise and energy use of the fan. Use the

shortest, straightest duct routing possible for best performance, and avoid installing the fan with smaller ducts than recommended.

Insulation around the ducts can reduce energy loss and inhibit mold growth. Fans installed with existing ducts may not achieve their

rated air ow.

Please remove duct assembly and blower assembly before installation.

EZ mounting frame Housing Duct Assembly Blower Assembly

1. Install EZ Mounting Frame

2. Install Duct And Housing

Attach duct assembly to frame using provided (1) 1/4" screw. Before

inserting the housing, first pull the locking tab located opposite of the

duct collar and push housing into the frame. Release the locking tab

so that it temporarily holds the housing in place. To secure permanently

in place, use the remaining (2) 1-inch screws as shown in the illustration.

3. Install Blower Assembly (Only necessary if installing a contractor pack)

Install blower assembly in housing and secure with screws.

Tab

Tab Tab

slot

hole

hole hole

7

fantech

4. Install Junction Box And Ductwork

Remove junction box cover and connect electrical wiring (refer to wiring diagram. Note:

1/2" strain relief not provided). Finish by replacing the junction box cover. Connect the

round ductwork (not included) to the damper/duct connector, and run the ductwork to a

roof or wall cap (not included). Using tape (not included), secure all the ductwork

connections so that they are air tight.

The ducting from this fan to the outside of building has a strong effect on the air flow,

noise and energy use of the fan. Use the shortest, straightest duct routing possible for

best performance, and avoid installing the fan with smaller ducts than recommended.

Insulation around the ducts can reduce energy loss and inhibit mold growth. Fans

installed with existing ducts may not achieve their rated air flow.

Wiring diagram

Run 120 Vac house wiring to the location of the fan. Use only UL-approved connectors (not included) to attach the field wiring to the

wiring plate. Refer to the wiring diagram, and connect the wires as shown.

Install the Grille

To attach the grille assembly to the fan housing. Insert the sensor plug into the mating

receptacle on the power box. Pinch the grille springs on the sides of the grille assembly,

and position the grille into the housing with the grille springs in the appropriate slots.

Push the grille assembly towards the ceiling to secure.

FAN

LIGHT

SWITCH BOX

WHITE

Fan

N

Sensor

GREEN

UNIT

LIGHT

SWITCH

FAN

SWITCH

BLACK

RED

WHITE

LINE

IN

CONTROL

CIRCUIT

Low CFM

switch

Humidity sensor

switch

S

BLACK

L1: light (Red)

L1: Mtr (Black)

N: Light & Mtr (White)

: Ground (Green)

2

8

fantech

Maintenance

For quiet and efficient operation, long life, and attractive appearance - lower or remove grille and vacuum interior of unit with the dusting brush

attachment.The motor is permanently lubricated and never needs oiling. If the motor bearings are making excessive or unusual noises, replace

the motor with the exact service motor. The impeller should also be replaced.

Keep all electrical components away from water. Do not use corrosive chemicals or water in excess of 60C (140°F) to clean plastic

parts.

Operation

See “Connect Wiring” for details.

The control box, located inside the fan housing, has three separate

adjustments:

(1) The low airflow knob(s) adjusts the lower airflow from 40CFM up to

the air flow rate of the high fan speed determined by the toggle switch

setting.

(2) The Humidity Sensor Knob set user adjustable setpoint (50%-100%

relative humidity).

(3) The toggle switch will adjust the upper fan speed setting from

80 to 140 CFM.

MOTION SENSOR

The fan will run continuously at the pre-set low speed. When motion is

detected, the fan speed increases to high speed. When the person exits the

area, the fan remains working at high speed until the delay time has passed

(20 minutes). After the time delay, the fan speed is reduced to the

continuous ventilation rate. Installation distance: 7 to 9 feet. Sensing range

is within the cone angle of 90°

HUMIDITY SENSOR OPERATION

The humidity-sensing fan uses a sophisticated humidity sensor that responds

to: (a) rapid to moderate (user-adjustable) increases in humidity or (b)

humidity above a user-adjustable set-point (50%-100% relative humidity).

The fan run continuously, at a preset lower level (set by the low speed

control Knob) and automatically boost up to high speed when environmental

conditions change. After delay timer (20 minutes), the fan returns to the

default low speed. If the fan continuously responds to changing environmental

conditions, “H” (means “humidity”) adjustment may be required. This figure is

factory-set for about 75% (Ambient temperature of 25°).

SENSITIVITY ADJUSTMENT

The “H” has been factory set for most shower applications. However, if the

fan is in a tub area or is being used for dampness control, the “H” may need

to be increased toward maximum “+”. If the control is responding too often

to changing environmental conditions, movement toward less “-” “H” may be

required. To adjust the “H”:

1. Disconnect power at service entrance.

2. Through the grille, locate the slot marked “H”.

3. Carefully rotate the “H” adjustment toward “+” or “-”.

4. Turn on power and check operation by turning on the shower or other

humidity source until the fan turns on.

5. Repeat above steps if necessary.

When the temperature changes, humidity sensor values will have deviation.

7 to 9 feet

Gesture area

sensor 90°

S H

~140

1 2 3

Switch

position

Airflow (CFM)

@0.1 INWC

~110

1 2 3

~90

1 2 3

~80

Hi Spd

Speed

setting

Med/HiMed/LoLo Spd

1 2

3

Speed control

for low speed

Humidity

HVI Certified performance based on HVI Procedures

915, 916, and 920.

Page is loading ...

15

fantech

Five (5) Year Warranty

This warranty supersedes all prior warranties

DURING ENTIRE WARRANTY PERIOD:

Fantech will repair or replace any part which has a factory defect in

workmanship or material. Product may need to be returned to the

Fantech factory, together with a copy of the bill of sale and identified

with RMA number.

FOR FACTORY RETURN YOU MUST:

• Have a Return Materials Authorization (RMA) number. This may be

obtained by calling Fantech either in the USA at 1.800.747.1762 or

in CANADA at 1.800.565.3548. Please have bill of sale available.

• The RMA number must be clearly written on the outside of the

carton, or the carton will be refused.

• All parts and/or product will be repaired/replaced and shipped back to

buyer; no credit will be issued.

OR

The Distributor may place an order for the warranty part and/or product

and is invoiced. The Distributor will receive a credit equal to the invoice

only after product is returned prepaid and verified to be defective.

FANTECH WARRANTY TERMS DO NOT PROVIDE FOR REPLACEMENT

WITHOUT CHARGE PRIOR TO INSPECTION FOR A DEFECT.

REPLACEMENTS ISSUED IN ADVANCE OF DEFECT INSPECTION ARE

INVOICED, AND CREDIT IS PENDING INSPECTION OF RETURNED

MATERIAL. DEFECTIVE MATERIAL RETURNED BY END USERS SHOULD

NOT BE REPLACED BY THE DISTRIBUTOR WITHOUT CHARGE TO THE

END USER, AS CREDIT TO DISTRIBUTOR’S ACCOUNT WILL BE

PENDING INSPECTION AND VERIFICATION OF ACTUAL DEFECT BY

FANTECH.

THE FOLLOWING WARRANTIES DO NOT APPLY:

• Damages from shipping, either concealed or visible. Claim must be

filed with freight company.

• Damages resulting from improper wiring or installation.

• Damages or failure caused by acts of God, or resulting from improper

consumer procedures, such as:

1. Improper maintenance

2. Misuse, abuse, abnormal use, or accident, and

3. Incorrect electrical voltage or current.

• Removal or any alteration made on the Fantech label control number

or date of manufacture.

• Any other warranty, expressed, implied or written, and to any

consequential or incidental damages, loss or property, revenues, or

profit, or costs of removal, installation or reinstallation, for any breach

of warranty.

WARRANTY VALIDATION

• The user must keep a copy of the bill of sale to verify purchase date.

• These warranties give you specific legal rights, and are subject to an

applicable consumer protection legislation. You may have additional

rights which vary from state to state.

This warranty does not apply to any Fantech product or part which has

failed as a result of faulty installation or abuse, incorrect electrical

connections or alterations made by others, or use under abnormal

operating conditions or misapplication of the product or parts. We will

not approve for payment any repair not made by us or our authorized

agent without prior written consent. The foregoing shall constitute our

sole and exclusive warranty and our sole exclusive liability, and is in lieu

of any other warranties, whether written, oral, implied or statutory.

There are no warranties which extend beyond the description on the

page hereof. In no event, whether as a result of breach of contract, or

warranty or alleged negligence, defect incorrect advice or other causes,

shall Fantech be liable for special or consequential damages, including,

but not limited to, loss of profits or revenue, loss of use of equipment or

any other associated equipment, cost of capital, cost of substitute

equipment, facilities or services, downtime costs, or claims of

customers of purchase for such damages. Fantech neither assumes or

authorizes any person to assume for it any other liability in connection

with the sale of product(s) or part(s). Some jurisdictions do not allow the

exclusion or limitation of incidental or consequential damages so the

above limitations and exclusions may not apply to you.

Limitation of Warranty and Liability Warning

Fantech products are designed and manufactured to provide reliable

performance, but they are not guaranteed to be 100% free from

defects. Even reliable products will experience occasional failures and

this possibility should be recognized by the user. If these products are

used in a life support ventilation system where failure could result in loss

or injury, the user should provide adequate backup ventilation,

supplementary natural ventilation, failure alarm system, or acknowledge

willingness to accept the risk of such loss or injury.

WARRANTY

Page is loading ...

Notes/Notas

Fantech reserves the right to make technical changes.

For updated documentation please refer to www.fantech.net

Fantech®

Fantech se réserve le droit de faire des changements

techniques. Pour de la documentation à jour, s'il vous plaît se

référer au www.fantech.net

Fantech se reserva el derecho de hacer modicaciones

técnicas en cualquier momento. Para obtener la documen-

tación actualizada, por favor consulte www.fantech.net

Fantech PROPLUS-L Installation guide

This manual is also suitable for

Fantech PROPLUS-L Installation guide

in other languages

Related papers

Other documents