Homestyles 5551-30 Operating instructions
- Type
- Operating instructions
Hardware List
Part List
20 05551 0030
Home Styles Customer Service: www.homestyles-furniture.com,
888-680-7460, 877-831-0319
Dining Table
A.
Top
1 pc.
B.
Leg
4 pcs.
C.
Side Frame
4 pcs.
Wrench
1 pc.
M8x40
Bolt
4 pcs. (+1 extra)
Flat Washer
12 pcs. (+1 extra)
Spring Washer
12 pcs. (+1 extra)
Nut
12 pcs. (+1 extra)
Nut Cap
12 pcs. (+1 extra)
Cover
1 pc.
Tool(s) required for assembly: Slotted screwdriver, Level
IMPORTANT
Carefully remove all the parts from the carton and place them
individually on a soft cloth to prevent scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
This product is made of aluminum. Do not use power tools
above 8 volts to assemble and only tighten bolts until snug.
Over tightening can damage the aluminum.
Assembly Instructions 2/3
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
Do not tighten all the bolts until each part is properly assembled.
The unit must be level to work properly. Use the included adjustable levelers to level.
Keep Wrench as the nuts may need to be tightened in the future.
Flat Washer
Spring Washer
Nut
Nut Cap
Nut Cap
Nut
Spring Washer
Flat Washer
Bolt
B
B
B
C
C
C
C
STEP 1
Attach Legs (B) to Side Frames (C) with Flat Washers, Spring Washers and Nuts, tightening nuts
only halfway. (See Figures 1 and 2)
Place Top (A) upside down on a soft cloth.
Insert Bolts into pre-drilled holes in Top (A), then tighten. (See Figure 3)
Attach unit to Top (A) with Flat Washers, Spring Washers and Nuts,
tightening nuts only halfway.
Tighten all Nuts.
Cover all Nuts with Nut Caps.
Figure 1
B
A
Figure 2
Figure 3
Assembly Instructions 3/3
Cover
STEP 2
Turn table over to its’ upright position.
Cover umbrella hole with Cover.
Level table by adjusting the adjustable levelers on bottom of legs.
(See Figure 4)
Figure 4
NEVER
use glass cleaners on
finished furniture. Ammonia
chemically attacks the finish.
allow liquids to remain on furniture.
Absorption causes parts to warp
and split and finishes to delaminate.
NEVER
CARE INSTRUCTIONS
Do not use rubber
based placemats.
PREVENT
DISCOLORING
Do not use commercial
waxes and polishes.
PREVENT
YELLOWING
Do not place hot
objects on surface.
PREVENT
FINISH DAMAGE
Do not write
directly on surface.
PREVENT
MARKING
Do not use power tools
above 8 volts to assemble.
PREVENT
CRACKING
Do not place
in direct sunlight.
PREVENT
FADING
with a soft cloth moistened
in lukewarm soap and water.
Buff with a dry clean cloth.
CLEAN
Home Styles will provide replacements free of charge for missing or damaged hardware or parts within 30 days of
purchase. Digital images of the defective parts may be required. If the product was not purchased from an authorized
retail affiliate, Home Styles is under no obligation to provide replacement parts. Parts are not available for fully assembled
items nor are parts available for sale. Replacements for missing or damaged hardware or parts may be requested at:
www.homestyles-furniture.com/customer-service/replacement-parts
Home Styles Customer Service: www.homestyles-furniture.com,
888-680-7460, 877-831-0319
Hardware List
Part List
20 05551 0032
Home Styles Customer Service: www.homestyles-furniture.com,
888-680-7460, 877-831-0319
Dining Table
A.
Top
1 pc.
B.
Leg
4 pcs.
C.
Side Frame
4 pcs.
Wrench
1 pc.
M8x40
Bolt
4 pcs. (+1 extra)
Flat Washer
12 pcs. (+1 extra)
Spring Washer
12 pcs. (+1 extra)
Nut
12 pcs. (+1 extra)
Nut Cap
12 pcs. (+1 extra)
Cover
1 pc.
Tool(s) required for assembly: Slotted screwdriver, Level
IMPORTANT
Carefully remove all the parts from the carton and place them
individually on a soft cloth to prevent scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
This product is made of aluminum. Do not use power tools
above 8 volts to assemble and only tighten bolts until snug.
Over tightening can damage the aluminum.
Assembly Instructions 2/3
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
Do not tighten all the bolts until each part is properly assembled.
The unit must be level to work properly. Use the included adjustable levelers to level.
Keep Wrench as the nuts may need to be tightened in the future.
Flat Washer
Spring Washer
Nut
Nut Cap
Nut Cap
Nut
Spring Washer
Flat Washer
Bolt
B
B
B
C
C
C
C
STEP 1
Attach Legs (B) to Side Frames (C) with Flat Washers, Spring Washers and Nuts, tightening nuts
only halfway. (See Figures 1 and 2)
Place Top (A) upside down on a soft cloth.
Insert Bolts into pre-drilled holes in Top (A), then tighten. (See Figure 3)
Attach unit to Top (A) with Flat Washers, Spring Washers and Nuts,
tightening nuts only halfway.
Tighten all Nuts.
Cover all Nuts with Nut Caps.
Figure 1
B
A
Figure 2
Figure 3
Assembly Instructions 3/3
Cover
STEP 2
Turn table over to its’ upright position.
Cover umbrella hole with Cover.
Level table by adjusting the adjustable levelers on bottom of legs.
(See Figure 4)
Figure 4
NEVER
use glass cleaners on
finished furniture. Ammonia
chemically attacks the finish.
allow liquids to remain on furniture.
Absorption causes parts to warp
and split and finishes to delaminate.
NEVER
CARE INSTRUCTIONS
Do not use rubber
based placemats.
PREVENT
DISCOLORING
Do not use commercial
waxes and polishes.
PREVENT
YELLOWING
Do not place hot
objects on surface.
PREVENT
FINISH DAMAGE
Do not write
directly on surface.
PREVENT
MARKING
Do not use power tools
above 8 volts to assemble.
PREVENT
CRACKING
Do not place
in direct sunlight.
PREVENT
FADING
with a soft cloth moistened
in lukewarm soap and water.
Buff with a dry clean cloth.
CLEAN
Home Styles will provide replacements free of charge for missing or damaged hardware or parts within 30 days of
purchase. Digital images of the defective parts may be required. If the product was not purchased from an authorized
retail affiliate, Home Styles is under no obligation to provide replacement parts. Parts are not available for fully assembled
items nor are parts available for sale. Replacements for missing or damaged hardware or parts may be requested at:
www.homestyles-furniture.com/customer-service/replacement-parts
Home Styles Customer Service: www.homestyles-furniture.com,
888-680-7460, 877-831-0319
Part List
Home Styles Customer Service: www.homestyles-furniture.com,
888-680-7460, 877-831-0319
20 05551 0037
IMPORTANT
B.
Leg
4 pcs.
C.
Side Frame
2 pcs.
D.
Side Frame
2 pcs.
A.
Top
1 pc.
Dining Table
Carefully remove all the parts from the carton and place them
individually on a soft cloth to prevent scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
This product is made of aluminum. Do not use power tools
above 8 volts to assemble and only tighten bolts until snug.
Over tightening can damage the aluminum.
Hardware List
Wrench
1 pc.
M8x40
Bolt
4 pcs. (+1 extra)
Flat Washer
12 pcs. (+1 extra)
Spring Washer
12 pcs. (+1 extra)
Nut
12 pcs. (+1 extra)
Nut Cap
12 pcs. (+1 extra)
Cover
1 pc.
Tool(s) required for assembly: Slotted screwdriver, Level
Assembly Instructions 2/3
Flat Washer
Spring Washer
Nut
Nut Cap
STEP 1
Attach Legs (B) to Side Frames (C) and Side Frames (D) with Flat Washers, Spring Washers and
Nuts, tightening nuts only halfway. (See Figures 1 and 2)
Figure 1
Figure 2
B
C
C
B
D
B
B
D
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
Do not tighten all the bolts until each part is properly assembled.
The unit must be level to work properly. Use the included adjustable levelers to level.
Keep Wrench as the bolts may need to be tightened in the future.
Cover
Assembly Instructions 3/3
Figure 4
STEP 3
Turn table over to its’ upright position.
Cover umbrella hole with Cover.
Level table by adjusting the adjustable levelers on bottom of legs.
(See Figure 4)
STEP 2
Place Top (A) upside down on a soft cloth.
Insert Bolts into pre-drilled holes in Top (A),
then tighten. (See Figure 3)
Attach unit to Top (A) with
Flat Washers, Spring Washers
and Nuts, tightening nuts
only halfway.
Tighten all Nuts used
in Steps 1 and 2.
Cover all Nuts with Nut Caps.
A
Nut Cap
Nut
Spring Washer
Flat Washer
Bolt
Figure 3
NEVER
use glass cleaners on
finished furniture. Ammonia
chemically attacks the finish.
allow liquids to remain on furniture.
Absorption causes parts to warp
and split and finishes to delaminate.
NEVER
CARE INSTRUCTIONS
Do not use rubber
based placemats.
PREVENT
DISCOLORING
Do not use commercial
waxes and polishes.
PREVENT
YELLOWING
Do not place hot
objects on surface.
PREVENT
FINISH DAMAGE
Do not write
directly on surface.
PREVENT
MARKING
Do not use power tools
above 8 volts to assemble.
PREVENT
CRACKING
Do not place
in direct sunlight.
PREVENT
FADING
with a soft cloth moistened
in lukewarm soap and water.
Buff with a dry clean cloth.
CLEAN
Home Styles will provide replacements free of charge for missing or damaged hardware or parts within 30 days of
purchase. Digital images of the defective parts may be required. If the product was not purchased from an authorized
retail affiliate, Home Styles is under no obligation to provide replacement parts. Parts are not available for fully assembled
items nor are parts available for sale. Replacements for missing or damaged hardware or parts may be requested at:
www.homestyles-furniture.com/customer-service/replacement-parts
Home Styles Customer Service: www.homestyles-furniture.com,
888-680-7460, 877-831-0319
Spring Washer
1 pc.
Flat Washer
1 pc.
M12
Nut
1 pc.
Hardware List
Part List
Home Styles Customer Service: www.homestyles-furniture.com,
888-680-7460, 877-831-0319
20 05551 0067
Umbrella Stand
IMPORTANT
A.
Top
1 pc.
B.
Base
1 pc.
Carefully remove all the parts from the carton and place them
individually on a soft cloth to prevent scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
This product is made of aluminum. Do not use power tools
above 8 volts to assemble and only tighten bolts until snug.
Over tightening can damage the aluminum.
Tool(s) required for assembly: 12MM Wrench or Adjustable Wrench
Assembly Instructions 2/2
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
STEP 1
Attach Top (A) to Base (B) with Flat Washer, Spring Washer and Nut.
Flat Washer
Spring Washer
Nut
A
B
NEVER
use glass cleaners on
finished furniture. Ammonia
chemically attacks the finish.
allow liquids to remain on furniture.
Absorption causes parts to warp
and split and finishes to delaminate.
NEVER
CARE INSTRUCTIONS
Do not use rubber
based placemats.
PREVENT
DISCOLORING
Do not use commercial
waxes and polishes.
PREVENT
YELLOWING
Do not place hot
objects on surface.
PREVENT
FINISH DAMAGE
Do not write
directly on surface.
PREVENT
MARKING
Do not use power tools
above 8 volts to assemble.
PREVENT
CRACKING
Do not place
in direct sunlight.
PREVENT
FADING
with a soft cloth moistened
in lukewarm soap and water.
Buff with a dry clean cloth.
CLEAN
Home Styles will provide replacements free of charge for missing or damaged hardware or parts within 30 days of
purchase. Digital images of the defective parts may be required. If the product was not purchased from an authorized
retail affiliate, Home Styles is under no obligation to provide replacement parts. Parts are not available for fully assembled
items nor are parts available for sale. Replacements for missing or damaged hardware or parts may be requested at:
www.homestyles-furniture.com/customer-service/replacement-parts
Home Styles Customer Service: www.homestyles-furniture.com,
888-680-7460, 877-831-0319
Part List
Home Styles Customer Service: www.homestyles-furniture.com,
888-680-7460, 877-831-0319
20 05551 0201
IMPORTANT
B.
Leg
4 pcs.
C.
Shelf
1 pc.
A.
Top
1 pc.
Accent Table
Carefully remove all the parts from the carton and place them
individually on a soft cloth to prevent scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
This product is made of aluminum. Do not use power tools
above 8 volts to assemble and only tighten bolts until snug.
Over tightening can damage the aluminum.
Hardware List
Wrench
1 pc.
M8x40
Bolt
4 pcs. (+1 extra)
Flat Washer
8 pcs. (+1 extra)
Spring Washer
8 pcs. (+1 extra)
Nut
8 pcs. (+1 extra)
Nut Cap
8 pcs. (+1 extra)
Tool(s) required for assembly: Slotted screwdriver, Level
Assembly Instructions 2/3
Nut Cap
Nut
Spring Washer
Flat Washer
Bolt
Nut Cap
Wrench
Nut
Spring Washer
Flat Washer
Bolt
STEP 1
Place Top (A) upside down on a soft cloth.
Insert Bolts into pre-drilled holes in Top (A),
then tighten.
(See Figure 1)
Attach Legs (B) to Top (A) with Flat Washers,
Spring Washers and Nuts, tightening nuts only
halfway with Wrench.
(See Figure 2)
B
B
B
B
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
Do not tighten all the bolts until each part is properly assembled.
The unit must be level to work properly. Use the included adjustable levelers to level.
Keep Wrench as the nuts may need to be tightened in the future.
Figure 2
Figure 1
A
Assembly Instructions 3/3
Figure 4
STEP 3
Turn table over to its’ upright position.
Level table by adjusting the adjustable levelers on bottom of legs.
(See Figure 4)
STEP 2
Attach Shelf (C) to unit with
Flat Washers, Spring Washers
and Nuts, tightening nuts
only halfway with Wrench.
(See Figure 3)
Tighten all Nuts used in Steps 1 and 2.
Cover all Nuts with Nut Caps.
Nut Cap
Nut
Spring Washer
Flat Washer
Figure 3
Spring Washer Flat Washer Bolt
Nut Cap Wrench Nut
C
NEVER
use glass cleaners on
finished furniture. Ammonia
chemically attacks the finish.
allow liquids to remain on furniture.
Absorption causes parts to warp
and split and finishes to delaminate.
NEVER
CARE INSTRUCTIONS
Do not use rubber
based placemats.
PREVENT
DISCOLORING
Do not use commercial
waxes and polishes.
PREVENT
YELLOWING
Do not place hot
objects on surface.
PREVENT
FINISH DAMAGE
Do not write
directly on surface.
PREVENT
MARKING
Do not use power tools
above 8 volts to assemble.
PREVENT
CRACKING
Do not place
in direct sunlight.
PREVENT
FADING
with a soft cloth moistened
in lukewarm soap and water.
Buff with a dry clean cloth.
CLEAN
Home Styles will provide replacements free of charge for missing or damaged hardware or parts within 30 days of
purchase. Digital images of the defective parts may be required. If the product was not purchased from an authorized
retail affiliate, Home Styles is under no obligation to provide replacement parts. Parts are not available for fully assembled
items nor are parts available for sale. Replacements for missing or damaged hardware or parts may be requested at:
www.homestyles-furniture.com/customer-service/replacement-parts
Home Styles Customer Service: www.homestyles-furniture.com,
888-680-7460, 877-831-0319
Hardware List
Part List
20 05550 0030
Home Styles Customer Service: www.homestyles-furniture.com,
888-680-7460, 877-831-0319
Dining Table
A.
Top
1 pc.
B.
Leg
4 pcs.
C.
Side Frame
4 pcs.
Wrench
1 pc.
M8x40
Bolt
4 pcs. (+1 extra)
Flat Washer
12 pcs. (+1 extra)
Spring Washer
12 pcs. (+1 extra)
Nut
12 pcs. (+1 extra)
Nut Cap
12 pcs. (+1 extra)
Cover
1 pc.
Tool(s) required for assembly: Slotted screwdriver, Level
IMPORTANT
Carefully remove all the parts from the carton and place them
individually on a soft cloth to prevent scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
This product is made of aluminum. Do not use power tools
above 8 volts to assemble and only tighten bolts until snug.
Over tightening can damage the aluminum.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
Homestyles 5551-30 Operating instructions
- Type
- Operating instructions
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Home Styles 5523-4015 Operating instructions
-
-
-
-
-
-
-
-
-
Home Styles 5559-3456 User guide
Other documents
-
-
-
Riverside Furniture 2909 Assembly Instructions
-
-
Home Decorators Collection 9528800270 Installation guide
-
Trex Outdoor Furniture TXS126-1-11VL Operating instructions
-
-
-
-
Cambridge Casual HD-225350 Installation guide
