i3 International SP12 PoE Splitter Quick start guide

i3 International
Brand
i3 International
Model
SP12 PoE Splitter
Category
PoE adapters
Type
Quick start guide

i3 International SP12 PoE Splitter is a device that receives power and data from a power over Ethernet network and separates the data from the power to provide both the data and direct current power to a non-PoE enabled device. It complies with IEEE 802.3 standards and supports two 10/100/1000M auto-detect Half/Full-Duplex switch ports with TX interfaces. It has auto-detection of PoE equipment, IEEE802.3at, protecting the device from being damaged by incorrect links. The splitter supplies a power source of 5V / 7.5V / 9V / 12V up to 2A peak and has LED indicators for Power function display.

i3 International SP12 PoE Splitter is a device that receives power and data from a power over Ethernet network and separates the data from the power to provide both the data and direct current power to a non-PoE enabled device. It complies with IEEE 802.3 standards and supports two 10/100/1000M auto-detect Half/Full-Duplex switch ports with TX interfaces. It has auto-detection of PoE equipment, IEEE802.3at, protecting the device from being damaged by incorrect links. The splitter supplies a power source of 5V / 7.5V / 9V / 12V up to 2A peak and has LED indicators for Power function display.

DIMENSIONS AND PORTS
Quick Start Guide
SP12 PoE Splitter
The SP12 PoE Splitter receives power and data from the power over Ethernet network and
separates the data from the power to provide both the data and 12V , 9V, 7.5V, or 5V direct
power to a non PoE enabled device.
• Four built-in mounting brackets for surface mounting (mounting screws not included)
• One RJ45 PoE in port
• One RJ45 Ethernet Data Out Port
• One DC Power Out Port
• One Voltage setting switch. 12V, 9V, 7.5V, and 5V
PACKAGE CONTENTS
Ensure that the items received match those listed on
the order form and the packing slip.
In addition to this manual the packing box includes:
1. One palm-sized SP12 PoE Splitter.
2. Two Power cables. One Red 5.5x2.5mm and one
Black 5.5x2.1mm
i3-TRNG-CAMS-SP12.indd
Rev. 160317
1. Install SP12 PoE Splitter for surface mounting as
required.
2. Four mounting screws (not included) can be used to
secure the splitter to a surface close enough to the
target device for the power cables to reach.
3. Insert the PoE Ethernet cable coming from the PoE
Switch or power injector hub into the Data Power In
Port.
4. Connect a CAT5/6 (not included) Ethernet cable into
the RJ45 Data Out Port on the splitter and connect it
into the data port on the target device.
5. Determine which power cable fits the target device.
The red cable has a 2.5mm connector and the black
has a 2.1mm connector. Connect the 5.5mm end of
the cord to the DC Power Out port on the splitter
and the other end of the cord into the power input of
the target device.
6. Ensure that the setting on the voltage selection
switch on the splitter is set to the power
requirements of the target device (12V, 9V, 7.5V, or
5V).
7. The LED indicators will glow Yellow to indicate the
splitter is powered on and functioning.
INSTALLATION INSTRUCTIONS
• It is the installer’s
responsibility to ensure
that the mounting surface
is suitable for the chosen
installation method.
• Based on installation
location and surface
type, supplied mounting
hardware may be
inadequate.
• Mounting hardware is
site-specific and will need
to be supplied by the
installer.
CAUTION
• Ensure the voltage
selection switch on the
side of the splitter is set
to the appropriate level
for the target device.
Improper voltage can
result in damage to the
non PoE device being
powered by the splitter.
IMPORTANT
5V
7.5V
9V
12V
Data Power In Port
LED Indicators
Height
27mm
(
1
1
/
16
”)
Length
72 mm
(2
3
/
4
”)
DC Power
Out
Width
78 mm
(3
1
/
16
”)
Data Out Port
Voltage Selector
Switch
KEY FEATURES
• Complies with IEEE802.3 10Base-T; IEEE802.3u,
100Base-TX; IEEE802.3ab, and 1000Base-T.
• Complies with IEEE802.3at PoE standards.
• Supports two 10/100/1000M auto-detect Half/Full-Duplex
switch ports with TX interfaces.
• Two RJ45 Port Interfaces, one Data+Power Input port; one
Data Output port and one Power Output port.
• Auto Detects PoE equipment, IEEE802.3at, protecting the
device from being damaged by incorrect links.
• Supplies a power source of 5V / 7.5V / 9V / 12V up to 2A
peak.
• LED indicators for Power function display.
• Ethernet Data Transfer rates: 10Mbps/Half-Duplex, 20Mbps/
Full-Duplex .
• Fast Ethernet Data Transfer Rates: 100Mbps / Half-Duplex,
200Mbps / Full-Duplex, Giga 2000Mpbs / Full-Duplex.
CANADA 780 Birchmount Road,
Unit 16, Toronto,
ON, M1K 5H4
U.S.A 4450 Witmer Industrial Estates
Unit 4 Niagara Falls,
NY 14305
www.i3international.com
1.866.840.0004
  • Page 1 1

i3 International SP12 PoE Splitter Quick start guide

i3 International
Brand
i3 International
Model
SP12 PoE Splitter
Category
PoE adapters
Type
Quick start guide

i3 International SP12 PoE Splitter is a device that receives power and data from a power over Ethernet network and separates the data from the power to provide both the data and direct current power to a non-PoE enabled device. It complies with IEEE 802.3 standards and supports two 10/100/1000M auto-detect Half/Full-Duplex switch ports with TX interfaces. It has auto-detection of PoE equipment, IEEE802.3at, protecting the device from being damaged by incorrect links. The splitter supplies a power source of 5V / 7.5V / 9V / 12V up to 2A peak and has LED indicators for Power function display.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents