ReliaBilt 243863 Installation guide

Brand: ReliaBilt

Model: 243863

Type: Installation guide

Tools Required:

Drill (optional)

Phillips

Screwdriver

Hacksaw

Tape Measure

Hammer

Step One

Trim Track to Fit Opening

(if necessary)

Cut the Top and Bottom

Track 1/16” (2mm) shorter

than the opening width with

a fine tooth hacksaw. Insert

the roll guides and fasten

the pivot brackets into the

track prior to installation of

the track. Install the pivot

brackets 1 7/8” (48mm)

from the wall as illustrated.

Step Three

Attach Top and

Bottom Track

Screw in tracks at a

minimum of ½“ (12mm),

in from the jamb face

(use long screws for the

top track and short

screws for the bottom

track). This will ensure

that the door does not

protrude from the

opening while it is

closed.

Step Two

Insert Pivots

Insert spring pivot into the

second hole at the top of the

pivot door. The bottom pivot,

used for height adjustment, must

be inserted into the second hole

at the bottom of the pivot door.

The remaining spring pivots are

inserted into the first holes of the

guide door.

Please Note: For Brass Laminate

bifold doors only, locate door with the

light scuff marks found at the

midpoint of the stiles. Orient this door

as pivot door. Affix door pull over

scuff marks (as per step 5).

Step Four

Install Doors

Insert the spring pivot on

the top of the pivot door

into the pivot bracket of

the top track. Then place

the bottom pivot into the

bracket of the bottom

track. Close the door so

that it is slightly ajar.

Depress the pivots in the

guide panel door and

snap the pins into the top

and bottom roll guides.

Note:

For heavier doors, you

may prefer to insert the

bottom pivot first.

Step Five

Final Adjustments

Both top and bottom pivot brackets can be

adjusted laterally. For lateral adjustment

release pivot bracket screw and slide pivot

bracket along track, once located, re-tighten

screw. Height adjustment is achieved by

lifting door slightly and turning the bottom

pivot with the aligner wrench as shown.

Attach the door pull onto the pivot door at

desired height (approx. 40” (1016mm) from

the floor). Clean the stile with isopropyl

(rubbing)alcohol before attaching the pull to

the door.

Trim snugger in 1/16” (2mm)

increments until door closes with a

light snap.

Height

Adjustment

Lateral

Adjustment

Pivot

Door

Snugger

Spring Pivot

Bottom Pivot

Guid

e

Doo

r

Pivot

Door

2nd Hole

1st Hole

Insertion of

roll guide

Insertion of pivot

bracket

½” (12mm)

Roll Guide

1 7/8”

(48mm)

Tracks must be

aligned and plumb

Four Door Application

P

i

v

o

t

D

o

o

r

G

u

i

d

e

D

o

o

r

G

u

i

d

e

D

o

o

r

P

i

vo

t

D

o

o

r

As per steps 1 - 5, pivot

brackets are installed

1-7/8” (48mm) from

each door jamb, and

roll guides are placed

at opposite end of the

pivot bracket as

illustrated. Place two

snuggers into top track.

Trim one snugger in

1/16” (2mm)

increments until doors

close with a light snap.

This Package Includes:

1 x Bifold Door

(2 panels)

2 x Track

(1 top, 1 bottom)

3 x Spring

Pivots

2 x Roll

Guides

2 x Pivot

Brackets &

Screws

1 x Door

Pull

1 x Snugger

1 x Bottom

Pivot

3 x Short

Screws(5/8”)

3 x Long

Screws(1½”)

Snuggers

Spring Pivots

Roll Guide

Bottom Pivot

Pivot Bracket

Snap pins into roll guide

using screwdriver

Spaced at 1 7/8

(48mm) from wall

Roll Guide

Spring Pivot

Spring Pivot

Pivot Bracket

Spring

Pivot

s

Bottom

Pivot

1 x Aligner

Wrench

Stiles

Rails

Door

Pull

1

ReliaBilt 243863 Installation guide

Brand: ReliaBilt

Model: 243863

Type: Installation guide

Download PDF

Related papers

Other documents