SY·BV5
TABLE BLENDER
USER
MANUAL
Welcome
Thank you for purchasing the Sytech SY-BV5 Electric table Blender. In order to fully benefit from this product,
please follow the instructions in this user manual very carefully. Store this user manual in a safe place for future
reference.
Important Safeguards
When using electrical appliances, basic safety precautions should always be followed,
including the following:
1. Read all instructions before operating.
2. Check if the voltage indicated on the base of the appliance corresponds to the local
mains voltage before you connect the appliance.
3. Do not touch hot surfaces. Use handles or knobs.
4. To protect against electrical shock, do not immerse cord, plug or appliance itself in
water or other liquids.
5. This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless
they have been given supervision or instructions concerning use of the appliance by a
person responsible for their safety.
6. Children should be supervised to ensure that they do not play with the appliance.
7. Do not operate any appliance with a damaged cord or plug or after the appliance
malfunctions or has been damaged in any manner. Return the appliance to the
nearest authorized service facility for examination, repair or adjustment.
8. Make sure all the parts are correctly mounted before you switch on the appliance.
9. Never reach into the feeding tube with your fingers or an object while the appliance is
running. Only the pusher is to be used for this purpose.
10. Do not remove the pulp container when the appliance is in operation.
11. The water temperature should not be over 60ºC when cleaning the unit.
12. The blender should not run for longer than 2 minutes. After each minute’s use,
the blender should be allowed to cool for at least 1 minute. This can be
repeated 10 times before further use. The appliance must be left to cool to room
temperature.
13. Unplug from outlet when not in use and before cleaning. Allow to cool before putting
on or taking off parts.
14. The use of accessory attachments not recommended by the appliance manufacturer
may cause injuries.
15. Do not use outdoors.
16. Do not let cord hang over edge of table or counter or touch hot surfaces.
17. Do not place on or near a hot gas or electric burner, or in a heated oven.
18. Always attach plug to appliance first, then plug cord into wall outlet. To disconnect,
turn any control to OFF position, then remove plug from wall outlet.
19. Oversized foods or metal utensils must not be inserted in the appliance as they may
cause a fire or risk of electrical shock.
20. Do not use the appliance if the rotating sieve is damaged.
21. Do not clean with metal scouring pads. Pieces can break off the pad and touch
electrical parts, involving a risk of electrical shock.
22. Extreme caution should be exercised when using containers constructed of other
material other than metal or glass.
23. Do not place any of the following materials inside the unit: Paper, cardboard, plastic
and similar.
Parts of the SY-BV5
1) Measuring cup
2) Lid
3) 1500ml. Glass Jar
4) Stirring blade base
5) Cup base
6) Motor Base
Before first use
All parts of the blender are to be thoroughly cleaned before being used for the first time. (See section:
Cleaning).
Take out the required length of cable from the cable tidy on the base of the blender and connect the device to
the mains supply.
Inserting the Glass Jars switched off (Switch in the ‘0’ setting).
1. Place the jar assembly on to the motor base and press down until it has been securely fitted.
Using the blender
1. Make sure the switch knob is set to”0” position.
2. Place the cup on the motor base and turn it clockwise.
3. Place the food items you wish to process into the glass jar.
4. Put the lid on the glass jar and close securely. Place the measuring cap into the hole in the lid.
5. Switch on the motor base:
Speed setting Use
0 – (Switch off) Stop operation.
1 – (Low) for light usage with liquids
2 – (High) for more solid consistency – for mixing liquids and solid foodstuffs
P (Pulse setting) for ice crushing & short, powerful impulse movements
(The switch does not permanently engage in the ‘P’ setting. You have to hold the switch in the ‘P’ setting or turn it
repeatedly into the ‘P’ setting)
NB: The blender should not run for longer than 2 minutes. After each minute’s use, the blender should be
allowed to cool for at least 1 minute. This can be repeated 10 times before further use, the unit must be
left to cool to room temperature.
After using the blender, always move the switch to the ‘0’ setting and pull out the mains plug.
To remove the glass jar simply turn anticlockwise and lift it off the motor base.
Useful tips:
To achieve the best results when pureeing solid ingredients, place small portions into the glass jar one by
one instead of placing a large quantity all at once.
If you are processing solid ingredients, cut them into small pieces (2-3cm) first.
When mixing solid ingredients start first with a small amount of liquid. Gradually add more and more liquid
through the opening in the lid.
Always place your hand on top of the blender when you are operating the device.
Be careful when processing hot liquids.
For stirring solid or very thick liquid ingredients, we recommend that you use the blender in impulse mode to
prevent the blades from becoming stuck.
Cleaning and Maintenance
- It is always easier to clean the appliance after immediate use.
- Do not use abrasive cleaning agents, scourers, acetone, alcohol, etc. to clean the appliance.
- Switch off the appliance before cleaning and remote the plug from the wall socket.
- Turn the blender cup clockwise to release the glass jar
- Clean all parts with a cleaning brush in warm water with some washing soap liquid and rinse it under the tap.
- Clean the motor base with a damp cloth. (never immerse the motor base in water, nor rinse it under the tap)
Specifications
Electric table blender
Ideal for chopping, mixing, liquefying or crushing ice
Modern design with safety lock
2-speed selector with Pulse function
Motor power: 600W.
Speed 1: 13.500 RPM
Speed 2: 17.500 RPM
1.5-liter glass jar resistant to temperature changes
Stainless steel 6 blades
Removable filter cap for easy filling
Detachable parts for easy cleaning
Voltage: 220V-240V, 50/60Hz
Declaration of Conformity
Manufacturer Name: Satyatrade S. L.
Address: Pol.Ind.La Raya. C/ Guadalquivir, 2.
Camarma de Esteruelas, 28816 Madrid
Tel: 902 430 967
Fax: 91 8864285
NIF: B83254763
Manufacturing country: China
Description: Electric Blender
Sytech® SY-BV5 complies with the following directives:
EMC Standard: Directive 2014/30/EU
LVD Standard: Directive 2014/35/EU
ROHS Standard: Directive 2011/65/EU Restriction of Hazardous Substances
Signed: Ajeet Nebhwani Utamchandani
Sole Administrator
/