Laney Amplification DB150C User manual

DB150C
Brand
Laney Amplification
Model
DB150C
Category
Home audio sets
Type
User manual

Laney Amplification DB150C is a bass amplifier with a wide range of features designed to give bassists versatile sound-shaping capabilities. With its FET and Tube preamp sections, you can achieve both clean and saturated preamp sounds. The built-in compressor helps tame unruly dynamics, providing a consistent and even output. Additionally, the 9-band graphic EQ and two pre-shape options let you further customize the sound. Connect your instrument using either the active or passive input, and utilize the XLR/jack input for direct connection to a mixing console.

Laney Amplification DB150C is a bass amplifier with a wide range of features designed to give bassists versatile sound-shaping capabilities. With its FET and Tube preamp sections, you can achieve both clean and saturated preamp sounds. The built-in compressor helps tame unruly dynamics, providing a consistent and even output. Additionally, the 9-band graphic EQ and two pre-shape options let you further customize the sound. Connect your instrument using either the active or passive input, and utilize the XLR/jack input for direct connection to a mixing console.

USER MANUAL
Laney
MODEL :
DB SERIES
DB150C
DB150H
DB300C
DB300H
DB400C
DB400H
Laney
Care of your amplifier will prolong it's life.....and yours!.Laney
After unpacking your amplifier check that it is factory fitted with a three pin 'grounded' (or earthed) plug. Before
plugging into the power supply ensure you are connecting to a grounded earth outlet.
If you should wish to change the factory fitted plug yourself, ensure that the wiring convention applicable to the country
where the amplifier is to be used is strictly conformed to. As an example in the United Kingdom the cable colour code
for connections are as follows.
EARTH OR GROUND - GREEN/YELLOW
NEUTRAL - BLUE
LIVE - BROWN
Congratulations on your decision to purchase a amplifier.
products are designed with ease of operation as a primary objective, however to ensure you derive the best from
your new amplifier, it is important you take time to read this user manual and to familiarise yourself with the control
functions and facilities available
Laney
Laney
INTRODUCTION
BEFORE
SWITCHING ON
This manual has been written for easy access of information. The front and rear panels of each unit are graphically
illustrated, with each control and feature numbered. For a description of the function of each control feature, simply
check the number with the explanations adjacent to each panel.
Your bass amplifier has undergone a thorough two stage, pre-delivery inspection, involving actual play
testing, as well as valve burn in. Valves are one of the most important components in your bass amp.
However they are also the most fragile component. The glass envelope and valve filaments can easily be damaged in
transit without any apparent signs of damage to the box, amp or valves.
Laney DB
Laney DB
When you first recieve your bass amp, follow these simple procedures:
(i) Ensure that the amplifier is set at the correct voltage for the country it is to be used in.
(ii) Connect your instrument with a high quality shielded instrument cable. Use of cheap cables will compromise the
sound of your instrument and your amplifier.
Laney DB
If there is a problem with your bass amplifierLaney DB
DON'T
DO
PHONE YOUR DEALER!
1
DB BASS MANUAL
ATTACK
4
5
6
7
1
2
3
8
9
17
21
18
22
20
10
19
1
1
14
16
11
10
13
15
12
9
8
7
65
4
3
DB BASS MANUAL
FRONT PANEL FEATURES
10
9
8
7
6
5
4
3
2
1
0
GRAPHIC EQ
VOLUME
EQ
LIMIT
POWER
1
0
GATE
NOISE
40Hz 80Hz
160Hz320Hz
650Hz 1k3Hz 2k6Hz
5kHz
10kHz
BALANCE
0
DB150C
OK
LEVEL
INPUT
PASSIVE
ACTIVE
FET
LO
8
10
9
8
7
6
5
4
3
2
1
0
10
9
7
6
5
4
3
2
1
0
PREAMPS
PRE
POST
TUBE
TUBE
10
9
8
7
6
5
4
3
2
1
0
HI
FET GAIN
0
5
4
3
2
1
-0+
1
2
3
4
5
BASS
PRESHAPE
MID
HI
5
4
3
2
1
-0+
1
2
3
4
5
TREBLE
10
9
8
7
6
5
4
3
2
1
0
10
9
8
7
6
5
4
3
2
1
0
10
9
8
7
6
5
4
3
2
1
0
10
9
8
7
6
5
4
3
2
1
0
10
9
8
7
6
5
4
3
2
1
0
5
4
3
2
1
-0+
1
2
3
4
5
5
4
3
2
1
-0+
1
2
3
4
5
LO
OK
HI
FET GAIN
PREAMPS
PRE
POST
TUBE
LEVEL
LEVEL
SUSTAIN
BASS
TREBLE
GRAPHIC EQGRAPHIC EQ
VOLUME
ON
ON
EQ
LIMIT
POWER
1
0
GATE
NOISE
40Hz 80Hz
160Hz
320Hz 650Hz 1k3Hz2k6Hz
5kHz
10kHz
BALANCE
PRESHAPE
MID
HI
ON
0 0
DB300H
PA D
INPUT
COMPRESSOR
10
9
8
7
6
5
4
3
2
1
0
10
9
8
7
6
5
4
3
2
1
0
2
INPUTS:
PRE AMP MODE SELECTOR:
TUBE PRE GAIN:
POST GAIN:
PRE-SHAPE:
BASS:
GRAPHIC:
BALANCE:
EQ:
VOLUME:
Active Input: Low sensitivity input for instrument with active circuitry and high output.
Passive Input: High sensitivity input for instrument with normal output i.e. Passive.
Allows access to the different pre amp modes. Pre amp mode selection is achieved
by depressing the relevant switch. With no switches depressed the unit defaults to FET. To access both FET and Tube
pre amp sections depress both switches simultaneously.
Sets the level of drive in the Tube pre amp circuit. Should be used in conjunction with POST gain
control to achieve the desired sound. To achieve a clean sound set the PRE gain level low whilst setting the POST gain
relatively high. To achieve a saturated pre amp sound set the PRE gain high and the POST gain relatively low.
Sets the level of post gain. See above for application.
Two factory set PRE-SHAPES are available. The MID PRE SHAPE produces an overall dip in the mid
frequency responce of the amp whilst at the same time boosting the low end of the amplifier. The HI PRE SHAPE
boosts the upper end frequency response of the amplifier. Both these PRE SHAPES can be selected simultaneously to
provide a third factory pre set. These pre shapes can be further modified by the units BASS, MID and GRAPHIC EQ
sections. PRE SHAPES are footswitchable on all models except DB150C and DB150H.
Controls the overall bass response of the amplifier
Nine band GRAPHIC. When switched out the EQ will be set in a flat frequency response. Voicings set via
the PRE-SHAPE can be further modified using the GRAPHIC.
Balances the pre amplifier output level when the GRAPHIC is assigned. Raising the slider increases the
output level of the GRAPHIC. Lowering the slider cuts the output of the GRAPHIC. BALANCE has no effect when
EQ is not selected
Enables the onboard GRAPHIC. The GRAPHIC can also be switched via a footswitch on all models. FS2
DB150C/DB150H FS4 footswitch. on all remaining models.
Sets the overall listening level of the amplifier
DB150C & DB150H
DB300C, DB300H, DB400C & DB400H
Laney
2
DB BASS MANUAL
DB150C & DB150H
DB300C, DB300H, DB400C & DB400H
20
22
14
15
16
17
11
12
13
18
19
17
21
18
22
20
21
19
1
1
14
16
11
10
13
15
12
9
8
7
65
4
3
FRONT PANEL FEATURES
10
9
8
7
6
5
4
3
2
1
0
GRAPHIC EQ
VOLUME
EQ
LIMIT
POWER
1
0
GATE
NOISE
40Hz 80Hz
160Hz320Hz
650Hz 1k3Hz 2k6Hz
5kHz
10kHz
BALANCE
0
DB150C
OK
LEVEL
INPUT
PASSIVE
ACTIVE
FET
LO
8
10
9
8
7
6
5
4
3
2
1
0
10
9
7
6
5
4
3
2
1
0
PREAMPS
PRE
POST
TUBE
TUBE
10
9
8
7
6
5
4
3
2
1
0
HI
FET GAIN
0
5
4
3
2
1
-0+
1
2
3
4
5
BASS
PRESHAPE
MID
HI
5
4
3
2
1
-0+
1
2
3
4
5
TREBLE
10
9
8
7
6
5
4
3
2
1
0
10
9
8
7
6
5
4
3
2
1
0
10
9
8
7
6
5
4
3
2
1
0
10
9
8
7
6
5
4
3
2
1
0
10
9
8
7
6
5
4
3
2
1
0
5
4
3
2
1
-0+
1
2
3
4
5
5
4
3
2
1
-0+
1
2
3
4
5
LO
OK
HI
FET GAIN
PREAMPS
PRE
POST
TUBE
LEVEL
AT TA CK
SUSTAIN
LEVEL
BASS
TREBLE
GRAPHIC EQGRAPHIC EQ
VOLUME
ON
ON
EQ
LIMIT
POWER
1
0
GATE
NOISE
40Hz 80Hz
160Hz
320Hz 650Hz 1k3Hz2k6Hz
5kHz
10kHz
BALANCE
PRESHAPE
MID
HI
ON
0 0
DB300H
PA D
INPUT
COMPRESSOR
10
9
8
7
6
5
4
3
2
1
0
10
9
8
7
6
5
4
3
2
1
0
2
LIMIT:
NOISE GATE:
POWER:
LEVEL INDICATORS:
FET GAIN:
TREBLE:
COMBINATION XLR/JACK INPUT:
PAD:
ON:
LEVEL:
SUSTAIN:
ATTACK:
Activates a fast attack compressor circuit. This is auto triggered by the output section, and prevent distortion
at high output levels.
When the amplifier is set for a high gain and high output volume; noise, hum and acoustic feedback
may become apparent. When selected (Pressed in) the noise reduction circuit is activated when playing ceases, greatly
reducing the unwanted noise. Note this is designed to be used at high gain and volme levels, use at low levels can
cause unwanted noise and result in premature signal cut off.
Illuminates when amplifier is switched on.
Indicates the strength of signal present in the pre-amplifier. If an ORANGE LED is
displayed the level of signal should be increased by means of the Pre-amp gains, using the appropriate gain controls. If
a GREEN LED is displayed the signal is at its optimum level. If a RED LED is displayed then the level present is too
high and should be adjusted accordingly.
Adjusts the level of gain for the FET (solid state) section of the pre amp. This control is only active if the
FET pre amp selector is assigned or if both pre amp modes are selected simultaneously
Controls the HIGH level frequency content of the amplifier.
Allows for the connection of an instrument using either XLR connectors of
Jacks
Pad switch for selecting between ACTIVE and PASSIVE input sources.
Switches the on board compressor on.
Controls the output level of the compressor when the compressor is switched on.
Controls the compression range and the length of sustain. Turning the control clockwise increases the level
of sustain.
Controls the envelope of the signal. Turning the control clockwise emphasizes the attack.
Laney
3
DB BASS MANUAL
30
23
24
25
26
27
28
29
36
35
32
34
33
28
27
26
31
30
29
HORN SWITCH:
SPEAKON OUTPUT:
JACK OUTPUT:
PRE AMP OUT:
XLR DIRECT INJECT:
DI SELECT:
FX LOOP PRE EQ:
FX LOOP POST EQ:
FOOTSWITCH:
Activates the on board COMPRESSION DRIVER. Not present on DB150H.
SPEAKON connector for connecting external speaker cabinet. Total minimum impedance of
enclosure connected to this socket must be no lower than 8 Ohm (4 Ohm DB400C/H) when used in conjunction with
another cabinet either connected to jack socket (25) or linked from the cabinet connected to the speakon connector. If
only a single enclosure is to be used the minimum impedance should be no lower than 4 Ohm. Not present on DB150C
JACK socket for connection of external speaker enclosure. See above.
Provides output to drive external power amplifier.
XLR socket for output of low impedance balanced line signal. Provides signal for use with
external mixing desks or PA system
Selects whether the signal sent to the XLR DIRECT INJECT is derived from a PRE EQ signal or a
POST EQ signal.
SEND & RETURN jacks for connection of external effects. Effects units connected to this set
of send and return sockets receive a PRE EQ signal. Should be used in conjunction with any effect which is going to
radically alter the sound of the amplifier, such as Octave dividers, distortion pedals etc.
SEND & RETURN jacks for the connection of external effects. An effect unit(s) connected to
this set of send and return sockets will recieve a POST EQ signal. Should be used in conjunction with effects such as
chorus, flanger or any type of digital pedal.
Should be used for connecting the correct type of footswitch to allow the remote switching of the
following features. DB150C & DB150H, FS2 for switching of GRAPHIC and INPUT MODE.
DB300C/DB300H/DB400C/DB400H, FS5 for switching of INPUT MODE/PRE SHAPE/GRAPHIC and
COMPRESSOR
TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT
REMOVE COVERS. NO USER SERVICABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
MADE IN THE UNITED KINGDOM BY BLT INDUSTRIES LTD.
SUPPLY VOLTAGE ~230V T1A
TO REDUCE THE RISK
TO REDUCE THE RISK OF
FIRE HAZARD REPLACE FUSE WITH
SAME TYPE AND RATING ONLY.
REMPLACER LE FUSIBLE
PAR LE MEME ET LE CALIBRE.
DEBRANCHER A LA PRISE
SECTEUR AVAVT D'OUVRIR.
CONSUMPTION 300 WATTS ~50 - 60 Hz.
& FUSE RATING ~115V T2A
RAIN OR MOISTURE.
NOT EXPOSE THIS APPLIANCE TO
OF FIRE OR ELECTRIC SHOCK DO
WARNING
CAUTION
ATTENTION
ATTENTION
CE
CAUTION
WARNING
THIS EQUIPMENT MUST BE EARTHED.
MAXIMUIM POWER
A TOTAL LOAD OF NO LESS THAN 8 OHMS
CAN BE CONNECTED AT ANY ONE TIME.
PIN -1 = GND.
PIN +1 = SIG.
SPEAKER OUTPUT
HORN
OFF
8P-86
DIRECT INJECT
SERIAL No:
PREAMP OUT
FX LOOP
FX LOOP
SEND SEND
PRE EQ.
POST EQ.
RETURN RETURN
FOOTSWITCH
PRE/POST
EQ
SEND SEND
PRE EQ.
POST EQ.
FX LOOP
FX LOOP
RETURN RETURN
FOOTSWITCH
DIRECT INJECT
PRE/POST
EQ
SPLIT
LO
HI
LEVEL
HI OUT
LO OUT
POWER AMP IN
PREAMP OUT
SUPPLY VOLTAGE ~230V T6.3A
& FUSE RATING ~115V T10A
TO REDUCE THE RISK
OF FIRE OR ELECTRIC SHOCK DO
NOT EXPOSE THIS APPLIANCE TO
CAUTION
TO REDUCE THE RISK OF
FIRE HAZARD REPLACE FUSE WITH
SAME TYPE AND RATING ONLY.
REMPLACER LE FUSIBLE
PAR LE MEME ET LE CALIBRE.
DEBRANCHER A LA PRISE
SECTEUR AVAVT D'OUVRIR.
WARNING
THIS EQUIPMENT MUST BE EARTHED.
SERIAL No:
MAXIMUIM POWER
CONSUMPTION 500 WATTS ~50 - 60 Hz.
ELECTRONIC CROSSOVER
SPEAKER OUTPUT
CE
MID
PIN -1 = GND.
PIN+1=SIG.
OFF
LO
HI
HORN
8P-8687
5
4
3
2
1
-0+-0+
1
2
3
4
5
WARNING
RAIN OR MOISTURE.
ATTENTION
ATTENTION
TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT
REMOVE COVERS. NO USER SERVICABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
MADE IN THE UNITED KINGDOM BY BLT INDUSTRIES LTD.
A TOTAL LOAD OF NO LESS THAN 8 OHMS
CAN BE CONNECTED AT ANY ONE TIME
CAUTION
23
31
24
25
REAR PANEL FEATURES
DB150C & DB150H
DB300C, DB300H, DB400C & DB400H
}
Laney
4
DB BASS MANUAL
32
33
34
35
36
35
32
34
33
28
27
26
31
30
29
HORN:
HI/LO SWITCH:
PRE AMP OUT POWER AMP IN:
ELECTRONIC CROSSOVER:
Activates the on board COMPRESSION DRIVER. Not present on DB300/400H.
When switched to the HI position the HORN runs at full level. When switched to LO the HORN
is attenuated down -6db.
PRE AMP OUT provides output to drive external power amplifier. This may be
used as an additional FX loop when used in conjunction with POWER AMP IN. POWER AMP IN provides an input
to the power amplifier for use as a slave amplifier.
The crossover consists of a HI OUT a LO OUT, a SPLIT function and a LEVEL
control. The LEVEL control determines the level of signal sent to either the HI or LO output. The SPLIT control sets
the frequency at which the crossover functions and the HI and LO outputs provide a signal to either the internal power
amp or an external power amplifier.
Lets look at the following example to gain an insight into how the crossover can be set up. Lets assume that you have a
DB400C and you wish to employ a 1x15 cabinet with a seperate power amplifier to handle the bottom end. To do this
you would first need to set the crossover frequency to LO. Using a straight Jack connector, connect the HI output to the
POWER AMP IN socket (34), This routes the HI frequency signal to the internal power amplifier which is
subsequently handled by the onboard speakers . Using a second jack connect the LO OUT socket to the input socket
of the external power amplifier connected to the 1x15 enclosurer. The DB400C will handle all the MID/HI frequencies
whilst the 1x15 will handle all the LO end.
To split the signal to allow a seperate 2 x 10" enclosure to handle the HI frequencies whist allowing the onboard
speaker to carry the remaining signal, patch the crossover as follows, SPLIT selector to HI, LO OUT connected to
POWER AMP IN, HI OUT to input of external power amplifier connected to 2 x 10" extension cab.
With nothing connected to the crossover patch bay, the unit defaults to full range regardless of where the SPLIT
function is set.
TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT
REMOVE COVERS. NO USER SERVICABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
MADE IN THE UNITED KINGDOM BY BLT INDUSTRIES LTD.
SUPPLY VOLTAGE ~230V T1A
TO REDUCE THE RISK
TO REDUCE THE RISK OF
FIRE HAZARD REPLACE FUSE WITH
SAME TYPE AND RATING ONLY.
REMPLACER LE FUSIBLE
PAR LE MEME ET LE CALIBRE.
DEBRANCHER A LA PRISE
SECTEUR AVAVT D'OUVRIR.
CONSUMPTION 300 WATTS ~50 - 60 Hz.
& FUSE RATING ~115V T2A
RAIN OR MOISTURE.
NOT EXPOSE THIS APPLIANCE TO
OF FIRE OR ELECTRIC SHOCK DO
WARNING
CAUTION
ATTENTION
ATTENTION
CE
CAUTION
WARNING
THIS EQUIPMENT MUST BE EARTHED.
MAXIMUIM POWER
A TOTAL LOAD OF NO LESS THAN 8 OHMS
CAN BE CONNECTED AT ANY ONE TIME.
PIN -1 = GND.
PIN +1 = SIG.
SPEAKER OUTPUT
HORN
OFF
8P-86
DIRECT INJECT
SERIAL No:
PREAMP OUT
FX LOOP
FX LOOP
SEND SEND
PRE EQ.
POST EQ.
RETURN RETURN
FOOTSWITCH
PRE/POST
EQ
SEND SEND
PRE EQ.
POST EQ.
FX LOOP
FX LOOP
RETURN RETURN
FOOTSWITCH
DIRECT INJECT
PRE/POST
EQ
SPLIT
LO
HI
LEVEL
HI OUT
LO OUT
POWER AMP IN
PREAMP OUT
SUPPLY VOLTAGE ~230V T6.3A
& FUSE RATING ~115V T10A
TO REDUCE THE RISK
OF FIRE OR ELECTRIC SHOCK DO
NOT EXPOSE THIS APPLIANCE TO
CAUTION
TO REDUCE THE RISK OF
FIRE HAZARD REPLACE FUSE WITH
SAME TYPE AND RATING ONLY.
REMPLACER LE FUSIBLE
PAR LE MEME ET LE CALIBRE.
DEBRANCHER A LA PRISE
SECTEUR AVAVT D'OUVRIR.
WARNING
THIS EQUIPMENT MUST BE EARTHED.
SERIAL No:
MAXIMUIM POWER
CONSUMPTION 500 WATTS ~50 - 60 Hz.
ELECTRONIC CROSSOVER
SPEAKER OUTPUT
CE
MID
PIN -1 = GND.
PIN+1=SIG.
OFF
LO
HI
HORN
8P-8687
5
4
3
2
1
-0+
1
2
3
4
5
WARNING
RAIN OR MOISTURE.
ATTENTION
ATTENTION
TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT
REMOVE COVERS. NO USER SERVICABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
MADE IN THE UNITED KINGDOM BY BLT INDUSTRIES LTD.
A TOTAL LOAD OF NO LESS THAN 8 OHMS
CAN BE CONNECTED AT ANY ONE TIME
CAUTION
23
24
25
REAR PANEL FEATURES
DB150C & DB150H
DB300C, DB300H, DB400C & DB400H
}
Laney
5
DB BASS MANUAL
36
36
35
32
34
33
28
27
26
31
30
29
SPEAKER OUTPUT JACKS: JACKconnectors for connecting external speaker cabinet . Total minimum impedance
of enclosure connected to this socket must be no lower than 8 Ohm (4 Ohm DB400C/H) when used in conjunction with
onboard speaker, another cabinet either connected to jack socket (25) or linked from the cabinet connected to the
speakon connector. If only a single enclosure is to be used the minimum impedance should be no lower than 4 Ohm (2
Ohm DB400H)
TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT
REMOVE COVERS. NO USER SERVICABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
MADE IN THE UNITED KINGDOM BY BLT INDUSTRIES LTD.
SUPPLY VOLTAGE ~230V T1A
TO REDUCE THE RISK
TO REDUCE THE RISK OF
FIRE HAZARD REPLACE FUSE WITH
SAME TYPE AND RATING ONLY.
REMPLACER LE FUSIBLE
PAR LE MEME ET LE CALIBRE.
DEBRANCHER A LA PRISE
SECTEUR AVAVT D'OUVRIR.
CONSUMPTION 300 WATTS ~50 - 60 Hz.
& FUSE RATING ~115V T2A
RAIN OR MOISTURE.
NOT EXPOSE THIS APPLIANCE TO
OF FIRE OR ELECTRIC SHOCK DO
WARNING
CAUTION
ATTENTION
ATTENTION
CE
CAUTION
WARNING
THIS EQUIPMENT MUST BE EARTHED.
MAXIMUIM POWER
A TOTAL LOAD OF NO LESS THAN 8 OHMS
CAN BE CONNECTED AT ANY ONE TIME.
PIN -1 = GND.
PIN +1 = SIG.
SPEAKER OUTPUT
HORN
OFF
8P-86
DIRECT INJECT
SERIAL No:
PREAMP OUT
FX LOOP
FX LOOP
SEND SEND
PRE EQ.
POST EQ.
RETURN RETURN
FOOTSWITCH
PRE/POST
EQ
SEND SEND
PRE EQ.
POST EQ.
FX LOOP
FX LOOP
RETURN RETURN
FOOTSWITCH
DIRECT INJECT
PRE/POST
EQ
SPLIT
LO
HI
LEVEL
HI OUT
LO OUT
POWER AMP IN
PREAMP OUT
SUPPLY VOLTAGE ~230V T6.3A
& FUSE RATING ~115V T10A
TO REDUCE THE RISK
OF FIRE OR ELECTRIC SHOCK DO
NOT EXPOSE THIS APPLIANCE TO
CAUTION
TO REDUCE THE RISK OF
FIRE HAZARD REPLACE FUSE WITH
SAME TYPE AND RATING ONLY.
REMPLACER LE FUSIBLE
PAR LE MEME ET LE CALIBRE.
DEBRANCHER A LA PRISE
SECTEUR AVAVT D'OUVRIR.
WARNING
THIS EQUIPMENT MUST BE EARTHED.
SERIAL No:
MAXIMUIM POWER
CONSUMPTION 500 WATTS ~50 - 60 Hz.
ELECTRONIC CROSSOVER
SPEAKER OUTPUT
CE
MID
PIN -1 = GND.
PIN+1=SIG.
OFF
LO
HI
HORN
8P-8687
5
4
3
2
1
-0+
1
2
3
4
5
WARNING
RAIN OR MOISTURE.
ATTENTION
ATTENTION
TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT
REMOVE COVERS. NO USER SERVICABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
MADE IN THE UNITED KINGDOM BY BLT INDUSTRIES LTD.
A TOTAL LOAD OF NO LESS THAN 8 OHMS
CAN BE CONNECTED AT ANY ONE TIME
CAUTION
23
24
25
REAR PANEL FEATURES
DB150C & DB150H
DB300C, DB300H, DB400C & DB400H
}
Laney
6
BLT Industries Ltd.,
Newlyn Road,
Cradley Heath,
West Midlands.
B64 6BE.
Tel: (0044) (0)1384 633821
Fax: (0044) (0)1384 639186
Http://www.laney.co.uk
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Laney Amplification DB150C User manual

DB150C
Brand
Laney Amplification
Model
DB150C
Category
Home audio sets
Type
User manual

Laney Amplification DB150C is a bass amplifier with a wide range of features designed to give bassists versatile sound-shaping capabilities. With its FET and Tube preamp sections, you can achieve both clean and saturated preamp sounds. The built-in compressor helps tame unruly dynamics, providing a consistent and even output. Additionally, the 9-band graphic EQ and two pre-shape options let you further customize the sound. Connect your instrument using either the active or passive input, and utilize the XLR/jack input for direct connection to a mixing console.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents