RECORD SERIAL NUMBER HERE
Note: Both Serial Number and Model Number are Required when Ordering Parts
(858) 578-9558
addendum
-5501
Fax
(800) 548-5438
(858) 578-7676
rpl
Customer Service
june, 2008
THE FOLLOWING PAGES WILL SUPERCEDE THE
EXISTING PAGES IN THE RPL-5501 MANUAL
CATALOG NUMBER 0208-004.
READ THIS FIRST!
RPL-5501
OWNER'S MANUAL
ADDENDUM
(w/ RUBBER FOOT)
41 7/16"
41 3/16"
(w/ OUT RUBBER FOOT)
OWNER'S MANUAL
PAGE 28
RPL-5501 ASSEMBLY
MACHINE ADJUSTMENT
LOOSEN JAM NUT AND TWIST TIE RODS (12) IN/OUT TO
ADJUST THE PRESS ARMS TO THE PROPER HEIGHT.
ONCE THE PROPER HEIGHT IS REACHED AND THE
PRESS ARMS ARE OF EQUAL HEIGHT, BE SURE TO
RE-TIGHTEN JAM NUTS.
MAJOR ADJUSTMENT:
TWIST TIE RODS (12):
CLOCKWISE TO DECREASE PRESS ARM HEIGHT
OR
COUNTER-CLOCKWISE TO INCREASE PRESS ARM HEIGHT.
41
41
CATALOG NUMBER
OWNER'S MANUAL
RECORD SERIAL NUMBER HERE
Fax
(800) 548-5438
(858) 578-7676
(858) 578-9558
Note: Both Serial Number and Model Number are Required when Ordering Parts
Customer Service
0208 - 005
PLATE-LOADED SHOULDER PRESS
RPL-5501
**WARNING!**
TO PREVENT POSSIBLE TIPPING, BOLT THIS UNIT TO THE
EXERCISE FLOOR. FAILURE TO DO SO MAY RESULT IN SERIOUS
INJURY OR DEATH.
02
04
28
30
31
32
33
36
37
39
41
42
43
44
45
OWNER'S MANUAL
PAGE 01
RPL-5501 ASSEMBLY
INSTRUCTIONS .....................................................................
FRAME ASSEMBLY ..............................................................
MACHINE ADJUSTMENT......................................................
PRE-ASSEMBLY....................................................................
DECAL PLACEMENT.............................................................
DECAL REFERENCE.............................................................
PART LIST...............................................................................
ABBREVIATIONS...................................................................
BOLT SIZING CHART............................................................
WASHER SIZING CHART......................................................
MAINTENANCE SCHEDULE.................................................
GENERAL MAINTENANCE INFORMATION........................
WEIGHT TRAINING TIPS.......................................................
EXERCISE LOG......................................................................
LIMITED WARRANTY............................................................
CONTENTS
OWNER'S MANUAL
PAGE 02
RPL-5501 ASSEMBLY
Ratchet Wrench
1/2", 9/16" and 3/4" Sockets
Adjustable Wrench
Rubber Mallet
Tape Measure
Level
Hex Key Wrench Set
Two People
TOOLS REQUIRED
Before beginning assembly please take the time to read instructions
thoroughly. Please use the various lists in this manual to make sure that
all parts have been included in your shipment. When ordering, use part
number and description from the lists. Use only HOIST replacement parts
when servicing. Failure to do so will void your warranty and could result
in personal injury.
HOIST equipment is designed to provide the smoothest, most effective
exercise motion possible. After assembly, you should check all functions to
ensure correct operation. If you experience problems, first recheck the
assembly instructions to locate any possible errors made during assembly.
If you are unable to correct the problem, call your authorized HOIST dealer.
Be sure to have your serial number and this manual when calling. When all
parts have been accounted for, continue on.
INSTRUCTIONS
***THIS PAGE WAS INTENTIONALLY LEFT BLANK***
OWNER'S MANUAL
PAGE 03
RPL-5501 ASSEMBLY
OWNER'S MANUAL
PAGE 04
RPL-5501 ASSEMBLY
FRAME ASSEMBLY
49
73
61
58
18
20
- WRENCH TIGHTEN HARDWARE.
NOTE:
FRAME ASSEMBLY
OWNER'S MANUAL
PAGE 05
RPL-5501 ASSEMBLY
13
50
29
15
14
20
FRAME ASSEMBLY
NOTE:
- HAND TIGHTEN HARDWARE.
OWNER'S MANUAL
RPL-5501 ASSEMBLY
PAGE 06
NOTE:
- WRENCH TIGHTEN HARDWARE.
FRAME ASSEMBLY
RPL-5501 ASSEMBLY
OWNER'S MANUAL
PAGE 07
58
83
64
33
70
58
14
36
59
84
78
59
78
59
10
84
59
14
FRAME ASSEMBLY
NOTE:
- HAND TIGHTEN HARDWARE.
OWNER'S MANUAL
RPL-5501 ASSEMBLY
PAGE 08
84
81
59
16
51
51
22
59
10
NOTE:
- HAND TIGHTEN HARDWARE.
FRAME ASSEMBLY
OWNER'S MANUAL
PAGE 09
RPL-5501 ASSEMBLY
FRAME ASSEMBLY
NOTE:
- HAND TIGHTEN HARDWARE.
- REPEAT ASSEMBLY FOR OPPOSITE
SIDE.
OWNER'S MANUAL
RPL-5501 ASSEMBLY
PAGE 10
74
59
22
59
84
16
14
- WRENCH TIGHTEN HARDWARE.
NOTE:
FRAME ASSEMBLY
OWNER'S MANUAL
PAGE 11
RPL-5501 ASSEMBLY
59
16
22
84
59
35
77
37
17
82
59
59
84
14
FRAME ASSEMBLY
NOTE:
- WRENCH TIGHTEN HARDWARE (82) THEN
LOOSEN NUT JUST ENOUGH FOR (17) TO
PIVOT FREELY.
OWNER'S MANUAL
RPL-5501 ASSEMBLY
PAGE 12
17
80
59
19
38
20
80
59
38
59
84
19
59
84
NOTE:
- WRENCH TIGHTEN HARDWARE (80) THEN
LOOSEN NUT JUST ENOUGH FOR (19) TO
PIVOT FREELY.
FRAME ASSEMBLY
OWNER'S MANUAL
PAGE 13
RPL-5501 ASSEMBLY
58
76
61
22
STEP 2:
FRAME ASSEMBLY
NOTE:
- WRENCH TIGHTEN HARDWARE.
- REPEAT ASSEMBLY FOR OPPOSITE
SIDE.
- SOME PARTS MAY HAVE BEEN REMOVED
FOR CLARITY.
OWNER'S MANUAL
RPL-5501 ASSEMBLY
PAGE 14
23
100
6399
22
STEP 1:
22
16
55
41
76
61
58
84
21
42
11
22
16
- WRENCH TIGHTEN HARDWARE.
SIDE.
- REPEAT ASSEMBLY FOR OPPOSITE
FRAME ASSEMBLY
NOTE:
OWNER'S MANUAL
PAGE 15
RPL-5501 ASSEMBLY
FRAME ASSEMBLY
NOTE:
- HAND TIGHTEN HARDWARE.
OWNER'S MANUAL
RPL-5501 ASSEMBLY
PAGE 16
WARNING - TIE ROD ENDS (24, 25) MUST BE THREADED
A MINIMUM OF 3/8" WITH JAM NUT (27, 28) TIGHTENED
SECURELY TO ENSURE PROPER CONNECTION.
24
28
12
27
25
24
28
12
27
25
102
102 101
101
2012
25
24
85
85
PROPERLY INSTALLED VIEW
11
21
- HAND TIGHTEN HARDWARE.
- REPEAT ASSEMBLY FOR OPPOSITE
SIDE.
FRAME ASSEMBLY
NOTE:
PAGE 17
OWNER'S MANUAL
RPL-5501 ASSEMBLY
102
101
85
BE SURE ORIENTATION OF CAP
WASHER (101) IS AS SHOWN
21
24
28
12
102
25
27
20
12
PROPERLY INSTALLED VIEW
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/
