Atlas Sound K-370A User manual

Atlas Sound
Brand
Atlas Sound
Model
K-370A
Type
User manual

This manual is also suitable for

Atlas Sound K-370A is a replacement sound chamber/diaphragm assembly for electronic siren speakers. It is a precision-engineered and tested part that will help you get your siren speaker up and running again. The K-370A is easy to install, and it comes with everything you need to get the job done right. With the K-370A, you can be sure that your siren speaker will be sounding its best for years to come.

Atlas Sound K-370A is a replacement sound chamber/diaphragm assembly for electronic siren speakers. It is a precision-engineered and tested part that will help you get your siren speaker up and running again. The K-370A is easy to install, and it comes with everything you need to get the job done right. With the K-370A, you can be sure that your siren speaker will be sounding its best for years to come.

Specifications are subject to change without notice
AtlasSound.com
1601 JACK MCKAY BOULEVARD ENNIS, TEXAS 75119 U.S.A. • TELEPHONE: (800) 876-3333 • FAX: (800) 765-3435
©2003 ATLAS SOUND LP Printed in U.S.A. 00303 ATS001542 RevA 3/03 PN 8838300
INSTALLATION INSTRUCTIONS
K-370A
REPLACEMENT SOUND CHAMBER/DIAPHRAGM ASSEMBLY
FOR ELECTRONIC SIREN SPEAKERS
This procedure describes the installation of a precision engineered and tested sound chamber/diaphragm assembly
(K-370A). Handle it with care and follow instructions precisely to assure a properly repaired siren driver.
Procedure for black or black/chrome driver
1. Clean the outside of the driver with a damp cloth to remove any dust, magnetic particles etc. before disassembly.
Ensure that the immediate work area is clear of magnetic particles that might be attracted to the air gap after the
driver is disassembled.
2. Remove and discard the eight screws and washers that secure the sound chamber to the magnetic assembly (pot).
3. With care, separate the sound chamber assembly from the magnetic assembly (pot). To avoid damage to the voice
coil, pull the sound chamber away evenly. Take care to avoid foreign matter being attracted and entering the
magnetized air gap.
4. If the new sound chamber will not be installed immediately, cover the air gap temporarily with masking tape to keep
dirt out.
5. Remove the tape covering the air gap (if installed in step 4) and inspect the gap with a strong light. Clean the gap
with a folded piece of masking tape (sticky side out). Repeat this step with a fresh piece of masking tape until the
air gap is clean.
6. Discard existing cork gasket(s) and install the two new cork gaskets into the sound chamber, aligning the slots on the
gasket I.D. with the terminal connections to the voice coil.
7. Loosely install sound chamber assembly to magnet assembly, aligning the terminal connections on the sound
chamber with the machined recesses on the magnetic assembly. Do not press the sound chamber on.
8. Install the eight new nylon washers and the eight new screws.
9. Tighten all screws finger tight.
10. Hold the two assemblies together and tighten the screws alternately. Tighten all screws with even torque.
11. Check the voice coil DC resistance with a meter. Resistance should be between 3.8 and 4.3 ohms (driver un-
powered and cold).
12. If the installation is a two-speaker system, be sure to connect the two drivers “in polarity” (lower sound output will
occur if the speakers are connected “out of polarity”).
  • Page 1 1

Atlas Sound K-370A User manual

Atlas Sound
Brand
Atlas Sound
Model
K-370A
Type
User manual
This manual is also suitable for

Atlas Sound K-370A is a replacement sound chamber/diaphragm assembly for electronic siren speakers. It is a precision-engineered and tested part that will help you get your siren speaker up and running again. The K-370A is easy to install, and it comes with everything you need to get the job done right. With the K-370A, you can be sure that your siren speaker will be sounding its best for years to come.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents