Avanti RH24P3S Door Reversal Instructions: Model RH24P3S - 24" Under Cabinet Ducted Range Hood

Avanti
Brand
Avanti
Model
RH24P3S
Type
Door Reversal Instructions: Model RH24P3S - 24" Under Cabinet Ducted Range Hood
INSTRUCTION MANUAL
MANUAL DE INSTRUCCIONES
Range Hood
Model Numbers / Nos. de Modelos:
RH24P0W
RH24P3S
BEFORE USE, PLEASE READ AND FOLLOW ALL SAFETY RULES AND OPERATING
INSTRUCTIONS. AND SAVE FOR LOCAL GAS AND ELECTRICAL INSPECTOR’S USE.
Avanti Products has a policy of continuous improvement on its products and reserves the right to change materials and
specifications without notice.
Avanti Products LLC
P.O. Box 520604 - Miami, Florida 33152
www.avantiproducts.com
TABLE OF CONTENTS
Range Hood Safety
3
Important Safe guides
4
Help Us Help You …
5
Parts and Features
6
Electrical Requirements
7
Before Using Your Range Hood
8
Operating Your Range Hood
9
Important Precautions and Recommendations
10
Installation - Mounting
11
Installation - Product Specifications
12
Installation- Electrical and Ducting
13 - 16
Care and Maintenance
17
Troubleshooting Guide
18
Service for Your Range Hood
18
Your AVANTI Products Warranty
19
Avanti Registration Card
20
2
IMPORTANT SAFETY INSTRUCTIONS
READ AND SAVE THESE INSTRUCTIONS
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always
read and obey all safety messages.
All safety messages will alert you what the potential hazard is, tell you how to reduce the chance of
injury, and let you know what can happen if the instructions are not followed.
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY TO PERSONS OBSERVE THE
FOLLOWING:
a) Use this unit only in the manner intended and expressed by the manufacturer, if you have any
questions, contact the manufacturer.
b) Before servicing or cleaning the unit, switch the power off at service panel and lock panel to
prevent power from being switched on accidentally. When the service disconnecting means
cannot be locked, securely fasten a prominent warning device, like a tag to the service panel.
CAUTION
For general ventilating use only. Do not exhaust hazardous or explosive materials and vapors. Take
care when using cleaning agents or detergents. Suitable for use in household/residential cooking
areas only.
WARNING:
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY TO PERSONS, OBSERVE THE
FOLLOWING:
a) Installation work and electrical wiring must be done by qualified person(s) in accordance with
all applicable codes and standards including fire-rated construction.
b) Sufficient air is needed for power combustion and exhausting of gases through the flue
(chimney) of fuel burning equipment to prevent back-drafting. Follow the heating equipment
manufacturer’s guideline and safety standards such as those published by the National Fire
Protection Association (NFPA) and the American Society for Heating, Refrigeration and Air
Conditioning Engineers (ASHRAE) and the local code authorities.
c) When cutting or drilling into a wall or ceiling, do not damage electrical wiring and other hidden
utilities.
d) Ducted fans must always vent to the outdoors.
e) Make sure the power is OFF before installing, wiring or maintenance.
3
IMPORTANT SAFE GUIDES
Before the appliance is used, it must be properly positioned and installed as
described in this manual, so read the manual carefully. To reduce the risk of
fire, electrical shock or injury when using the appliance, follow basic
precaution, including the following:
• It is recommended that a separate circuit, serving only your appliance be provided. Use
receptacles that cannot be turned off by a switch or pull chain.
• Never clean appliance parts with flammable fluids. These fumes can create a fire hazard or
explosion. And do not store or use gasoline or other flammable vapors and liquids in the vicinity of
this or any other appliance. The fumes can create a fire hazard or explosion.
• Before proceeding with cleaning and maintenance operations, make sure the power line of the
unit is disconnected.
• Unplug the appliance or disconnect power before cleaning or servicing. Failure to do so can result
in electrical shock or death.
• Do not attempt to repair or replace any part of your appliance unless it is specifically
recommended in this manual. All other servicing should be referred to a qualified technician.
• All openings in the wall behind the appliance and in the floor under the appliance shall be sealed.
• Keep appliance area clear and free from combustible materials, gasoline, and other flammable
vapors.
• Do not obstruct the flow of ventilation air.
• Disconnect the electrical supply to the appliance before servicing.
• When removing appliance for cleaning and/or service:
• Disconnect AC power supply.
• Electrical Grounding Instructions - The appliance must be installed and grounded by a qualified
technician in accordance with the National Electrical Code ANSI/NFPA No. 70 (Latest Edition)
and local electrical code requirements.
• Replacement Parts – Only authorized replacement parts may be used in performing service on
the range hood. Replacement parts are available from factory authorized parts distributors.
Contact the nearest Avanti service center in your area.
WARNING: If the information in this manual is not followed exactly, a fire or
explosion may result causing property damage, personal injury or death.
4
HELP US HELP YOU...
Read this guide carefully.
It is intended to help you operate and maintain
your new appliance properly.
Keep it handy to answer your questions.
If you don't understand something or you
need more assistance, please call:
Avanti Customer Service
800-220-5570
Keep proof of original purchase date (such as
your sales slip) with this guide to establish the
warranty period.
Write down the model and serial numbers.
You'll find them on a plate located on the
appliance.
Please write these numbers here:
____________________________________
Date of Purchase
____________________________________
Model Number
____________________________________
Serial Number
Use these numbers in any correspondence or
service calls concerning your appliance.
If you received a damaged appliance,
immediately contact the dealer (or builder) that
sold you the appliance.
Save time and money. Before you call for
service, check the Troubleshooting Guide. It
lists causes of minor operating problems that
you can correct yourself.
IF YOU NEED SERVICE
We're proud of our service and want you to be
pleased. If for some reason you are not happy
with the service you receive, here are some
steps to follow for further assistance.
FIRST, contact the people who serviced your
applaince. Explain why you are not pleased. In
most cases, this will solve the problem.
NEXT, if you are still not pleased, write all the
details, including your telephone number, and
send it to:
Customer Service
Avanti Products
10880 NW 30 Street
Miami, FL 33172
5
PARTS & FEATURES
1
Control Panel
2
LED Light Bulbs (2)
3
Removable / Cleanable Mesh Air Filters (2)
CONTROL PANEL
1
Power ON/OFF Button (Red indicator Light)
2
Fan Speed Selector Button (Blue indicator light)
Fan Speeds: OFF / High / Medium / Low
3
Light ON / OFF Selector Button (Blue indicator light)
Light modes: OFF / High / Low
6
ELECTRICAL REQUIREMENTS
WARNING
All electrical work must be performed by a qualified electrician or person
with similar technical knowhow and background.
For personal safety, remove house electrical fuse or open circuit breaker
before beginning installation. DO NOT USE EXTENSION CORD OR
ADAPTER PLUG WITH THIS APPLIANCE.
Follow all national electrical codes or prevailing local codes and
ordinances.
Electrical supply:
This appliance requires a 120V / 60 Hz electrical supply, connected to an
individual properly grounded branch circuit, protected by a 15 or 20
ampere circuit breaker or time delay fuse. Wiring must be a 2 wire with
ground. Please refer to the electrical diagram labeled on the product.
IMPORTANT:
You MUST observe all governing codes and ordinances.
It is the customer’s responsibility
A) To contact a qualified electrical installer
B) To assure that the electrical installation is adequate and in conformance with
the National Electrical Code, ANSI/NFPA 70 latest edition* or CSA standards
C22.1-94, Canadian Electrical Code part 1 and C22.2 No. 0-M91 – latest
edition** and all local codes and ordinances.
If codes permit and a separate ground wire is used, it is recommended that a
qualified electrician determine that the ground path is adequate.
DO NOT ground to a gas pipe.
Check with a qualified electrician if you are not sure the range hood is properly
grounded.
DO NOT have a fuse in the neutral or ground circuit.
*National Fire Protection Association Batterymarch Park, Quincy, MA 02269
** CSA International 8501 East Pleasant Valley Road, Cleveland, OH 44131
CABLE LOCK:
A cable locking connector (not supplied) might also be required by local
codes. Check with local requirements and codes, purchase and install
appropriate connector if necessary.
7
Before Using Your Range Hood
√Remove the exterior and interior packing.
√Remove the protective film on steel and aluminum parts
√Check to be sure you have all of the parts listed below
● (1) Range Hood
● (2) Aluminum Mesh Filters(Pre-installed)
● (2) LED Light bulbs (Pre-installed)
● (1) LED Bulb Removal Suction Cup.
● (1) Installation Template
● (1) Installation Hardware Kit
● (1) Instruction Manual
● (1)Damper
√ Have your range hood installed and properly grounded by a qualified installer in accordance
with the installation instructions.
√ Do not attempt to repair or replace any part of your range hood unless it is specifically
recommended in this manual.
√ Do not remove permanently affixed labels, warnings, or plates from the product. This may
void the warranty.
√ The installer should leave these instructions with the consumer who should retain for local
inspector’s use and for future reference.
√ Please observe all local and national codes and ordinances.
Important:
This appliance is designed and manufactured solely for the cooking of domestic (household) food and
is not suitable for any non-domestic application and therefore CANNOT be used in a commercial
environment.
The appliance guarantee will be void if the appliance is used within a non-domestic environment i.e. a
semi-commercial, commercial or communal environment.
Read the instructions carefully before installing and using the appliance.
8
OPERATING YOUR RANGE HOOD
GENERAL OPERATION
1
Power ON / OFF:
Press this button to turn the power ON or OFF. When the power is
turned on a red indicator light will be seen above the button.
2
Fan Speed selector button:
After turning the power on, press this button to select the desired fan
speed. When the fan is in operation a blue indicator light will be seen
above the button and beep will be heard after each time the button is
pressed.
Selections range from:
OFF: NO fan
HIGH: High fan speed (One beep)
MED: Medium fan speed (Two beeps)
LOW: Low fan speed (Three beeps)
3
Light Mode selector button:
After turning the power on, press the button to select the desired light
mode. When the light is on a blue indicator light will be seen above
the button and a beep sound will be heard after each time the button is
pressed.
Mode range:
OFF: No light
High: High level
Low: Low level
9
IMPORTANT PRECAUTIONS AND RECOMMENDATIONS
√ After having unpacked the appliance, check to ensure that it is not damaged. In case
of doubt, do not use it and consult your supplier or a professionally qualified technician.
√ Packing elements (i.e. plastic bags, polystyrene foam, nails, packing straps, etc.)
should not be left around within easy reach of children, as these may cause serious
injuries.
√ The packaging material is recyclable and is marked with the recycling symbol
.
√ Do not attempt to modify the technical characteristics of the appliance as this may
cause danger to users.
√ Do not carry out cleaning or maintenance operations on the appliance without having
previously disconnected it from the electric power supply.
√ If you should decide not to use this appliance any longer (or decide to substitute
another model), before disposing of it, it is recommended that it be made inoperative
in an appropriate manner in accordance to health and environmental protection
regulations, ensuring in particular that all potentially hazardous parts be made
harmless, especially in relation to children who could play with unused appliances.
√ After use, ensure that the buttons are in OFF position.
√ Do not allow children or other unqualified people to use the appliance without your
supervision.
√ Keep children away from the range hood when it is in use
√ The manufacturer declines all liability for injury to persons or damage to property
caused by incorrect or improper use of the appliance.
√ To avoid any possible hazard, the appliance must be installed by qualified personnel
only. Any repairs by unqualified persons may result in electric shock or short circuit. In
order to avoid possible injuries to your body or to the appliance, do not attempt any
repairs by yourself. Such work should be carried out by qualified service personnel
only.
√ This appliance is intended for use in your household. Never use the appliance for any
other purpose!
IMPORTANT PRECAUTIONS AND RECOMMENDATIONS FOR USE OF
ELECTRICAL APPLIANCES
Use of any electrical appliance implies the necessity to follow a series of fundamental rules.
In particular:
✓ Never touch the appliance with wet hands or feet;
✓ Do not operate the appliance barefooted;
✓ Do not allow children or disabled people to use the appliance without your supervision.
The manufacturer cannot be held responsible for any damages caused by improper,
incorrect or unreasonable use of the appliance
10
INSTALLATION – MOUNTING
Ducting
A minimum 3 ¼ x 10” rectangular duct must be used to maintain maximum air flow efficiency.
Always use rigid type metal ducts only. Flexible ducts could restrict air flow by up to 50%.
Always when possible, reduce the number of transitions and turns. If a reducer is used, install a long
reducer instead of a pancake reducer. Reduce duct size as far away from opening as possible.
If turns or transitions are required; install as far away from opening and as far apart as possible.
Never exhaust air or terminate duct work into spaces between walls, crawl spaces, ceilings, attics or
garages.
All exhaust must be ducted to the outside, unless using the recirculating kit.
Use single wall rigid metal duct work only.
Fasten all connections with sheet metal screws and tape all joints with certified Silver Tape or Duct
Tape.
MOUNTING
Minimum mount height between range top to hood
bottom should be no less than 24” (inches).
Maximum mount height should be no higher than 32”
(inches).
It is important to install the hood at the proper mounting
height. Hoods mounted too low could result in heat
damage and fire hazard; while hoods mounted too high
will be hard to reach and will loose its performance and
efficiency.
If available, also refer to the range manufacturer’s
height clearance requirements and recommended hood
mounting height above range. Always check your local
codes for any differences.
NET WIDTH
Min: 24
”
Max 32
”
11
INSTALLATION – PRODUCT SPECIFICATIONS
Top
View
Side
View
Back
View
12
INSTALLATION – ELECTRICAL AND DUCTING
Preparation – General – Non-Ducted – Recirculation Kit
Use the follow steps to set up and install your range hood using the recirculation kit (sold separately).
1) Remove the filters
2) Remove the cover from the junction box and access the electrical wiring.
3) If using a cable lock (not provided) pry open the desired electrical knockout (either on the top
or the back panel).
4) Feed the wires through the ¾” cable lock. Note some local codes require the use of a cable
lock, check your local codes for this information.
5) Get the Recirculation Kit (Not provided, optional). If you are installing the hood to be used
with the ducting kit, jump to the next section.
6) Install the screw clips for charcoal filter
7) Insert the charcoal filter
8) Secure the charcoal filter
9) Remove the recirculating plate on the top
10) Instal the recirculating grille
11) Put the two mesh filters back to the unit, and now you can install unit to your cabinet.
Recirculation kit must be installed to the unit prior to final installation.
Step 5. An air recirculating
kit (optional ) must be
purchased before using hood
in recirculating mode .
Step 1. Remove the filters
Step 2. Remove the cover from
the junction box and access
the electrical wiring.
Step3 & 4. If using a cable lock (not
provided) pry open the desired electrical
knockout (either on the top or the back
panel).
13
Step 6. Attach the spring clips (2) to the safety
grille body by inserting the screw through the
spring and into the clip. Then secure each clip
to the safety grille using a Phillips head
screwdriver.
Step 7. Insert the charcoal filter into
the filter assembly and place it over
the safety grille body.
Step 8. Secure the filter assembly to
the grille assembly by gently lifting the
spring clips and twisting. The spring
clip should cover the rim or lip of the
filter assembly, and secure it in place.
Step 10. Install the recirculating
kit louver using the screws
removed in step #9
Step 9.Remove the 3 screws
holding the recirculating panel.
Remove panel.
Step 11. Put the two mesh filters back to
complete the installation.
14
Preparation – General – Ducted Installation
Start from Step 1-4
Step 5. Find the accessories for ducting installation
Step 6.Remove the recirculating panels.
Step 7. Install the two arced plates to the unit and then install the recirculating panels removed from
step 6.
Step 8. Remove the 2 screws that hold the small back cover.
15
Step 9. Insert the blocking plate and replace the cover.
Step 10. Pry open the desired 3¼” x 10” ducting knock out (either on the top or the back panel), then
attach the 3¼” x 10” starting collar with damper to the duct opening exposed.
Final Installation.
16
CARE & MAINTENANCE
WARNING:
GENERAL RECOMMENDATION
SWITCH OFF THE ELECTRIC SUPPLY BEFORE MAINTENCE
ALUMINUM MESH FILTERS (MAINTENANCE)
The filters are made of an aluminum mesh material and are designed to trap residue and grease
while cooking. The filters should never need to be replaced while they are maintained correctly.
You will need to clean the filters at least once every 30 days or when needed depending on your
normal cooking habits.
Filters may be cleaned in the dishwasher on the lowest or economical setting or simply soaked in hot
soapy water. Be sure filters are completely dry before re-installing them to the range hood.
• Press the filter release button
• Tilt the filter downward and remove.
• To replace the filters do the above steps in reverse.
REPLACING THE HOOD LIGHTS
• Switch off the electric supply.
• Using the bulb removal suction cup included, press the bulb upward and turn in a counter-
clockwise motion. ** NOTE – The light bulb does not actual rotate but will turn slightly
(approximately 40 – 50 degrees) and will fall downward.
• If the bulb is hard to turn due to extended use, use a rubber/latex glove to press upward and turn
counter-clockwise.
• Replacement bulbs are available at most local hardware, appliance and or home stores.
• In the event the bulbs do not light up, rotate them 180º to obtain the correct polarity.
Purchase only (GU-10 LED 5W (3000K) bulbs (12V).
View from the bottom of the hood.
NOTE: Hood bulb replacement is not covered by your limited warranty.
17
PROBLEMS WITH YOUR RANGE HOOD?
You can solve many common appliance problems easily, saving you the cost of a possible service
call. Try the suggestions below to see if you can solve the problem before calling the servicer.
TROUBLESHOOTING GUIDE
FIND YOUR
PROBLEM HERE
POSSIBLE CAUSE HOW TO FIX IT
Fan does not work Power is turned off
Press the power ON / OFF button, be sure
the red indicator light is on above the power
button.
Fan speed is too low Fan speed selection is on low
Press the fan speed selector button and
select a higher speed.
Lights do not work.
Burned out / loose bulb
Or incorrect polarity
Tighten or replace light bulb.
Power is turned off
Press the power ON / OFF button, be sure
the red indicator light is on above the power
button.
Light mode is set to the off position, select
the appropriate mode low or high.
Light Bulb is installed
incorrectly
Remove the bulb and rotate 180º to obtain
the correct polarity.
SERVICE FOR YOUR RANGE HOOD
We are proud of our customer service organization and the network of professional service
technicians that provide service on your Avanti appliances. With the purchase of your Avanti
appliance, you can have the confidence that if you ever need additional information or assistance, the
Avanti Products Customer Service team will be here for you. Just call us toll-free.
AVANTI PRODUCTS CUSTOMER SERVICES
Product Information
800-323-5029
Whatever your questions are about our products,
help is available.
Part Orders
800-220-5570
You may order parts and accessories that will be
delivered directly to your home by personal
check, money order, Master Card, or Visa.
In-Home Repair Service
800-220-5570
An Avanti Products authorized service center will
provide expert repair service, scheduled at a time
that is convenient for you. Our trained servicers
know your appliance inside and out.
18
YOUR AVANTI PRODUCTS WARRANTY
WARRANTY – RANGE HOOD
LENGTH OF WARRANTY
WE WILL PAY FOR
FULL ONE YEAR WARRANTY FROM DATE
OF PURCHASE ON ALL PARTS EXCEPT
GLASS PARTS.
IN RENTAL OR COMMERCIAL USE, THE
WARRANTY PERIOD IS 90 DAYS.
REPLACEMENT PARTS AND REPAIR
LABOR TO CORRECT DEFECTS IN
MATERIALS OR WORKMANSHIP.
SERVICE MUST BE PROVIDED BY AN
AUTHORIZED SERVICE COMPANY.
FULL 30-DAY WARRANTY FROM DATE OF
PURCHASE ON GLASS PARTS AND FINISH
OF PORCELAIN ENAMEL, PAINTED OR
BRIGHT METAL FINISHED PARTS
REPLACEMENT PARTS AND REPAIR
LABOR TO CORRECT DEFECTS IN
MATERIAL OR WORKMANSHIP.
SERVICE MUST BE PROVIDED BY AN
AUTHORIZED SERVICE COMPANY.
WE WILL NOY PAY FOR
A. Service calls to:
1. Correct the installation of your range hood.
2. Instruct you how to use your range hood.
3. Replace house fuses or correct house wiring.
4. Replace owner-accessible light bulbs.
B. Surcharges including, but not limited to, any after hour, weekend, or holiday service
calls, tolls, ferry trip charges, or mileage expense for serviced calls to remote areas,
including the state of Alaska.
C. Damage to your range hood caused by accident, misuse, fire, flood, acts of God, or
use of products not mentioned in this manual.
D. Repairs to parts or systems caused as a result of unauthorized modifications made
to the appliance.
E. Shipping and handling costs associated with the replacement of the unit.
F. Repairs when your range hood is used in other than normal, single-family household
use.
AVANTI PRODUCTS SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL
DAMAGES.
Some states do not allow the exclusion or limitation of incidental or consequential damages,
so this exclusion or limitation may not apply to you. This warranty gives you specific legal
rights, and you may also have other rights that vary from state to state.
This warranty is not valid outside the Continental United States.
19
Registration Information
Thank you for purchasing this fine Avanti product. Please fill out this form and return it to the
following address within 100 days from the date of purchase and receive these important benefits:
Avanti Products, LLC.
P.O.Box 520604 – Miami, Florida 33152
Protect your product:
We will keep the model number and date of purchase of your new Avanti product on file to
help you refer to this information in the event of an insurance claim such as fire or theft.
Promote better products:
We value your input. Your responses will help us develop products designed to best meet
your future needs.
-------------------------------------------------------(detach here)--------------------------------------------------------------
Avanti Registration Card
Name
Model # Serial #
Address
Date Purchased Store / Dealer Name
City State Zip
E-mail Address
Area Code Phone Number
Occupation
Did You Purchase An Additional Warranty
As your Primary Residence, Do You:
Extended
Own Rent
None
Your Age:
Reason for Choosing This Avanti Product:
Please indicate the most important factors
That influenced your decision to purchase
this product:
under 18
18-25
26-30
31-35 36-50 over 50
Marital Status:
Married Single
Price
Product Features
Avanti Reputation
Product Quality
Salesperson Recommendation
Other: ___________________
Friend / Relative Recommendation
Warranty
Other: ___________________
Is This Product Used In The:
Home Business
How Did You Learn About This Product:
Advertising
In-Store Demo
Personal Demo
Comments:
20
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21

Avanti RH24P3S Door Reversal Instructions: Model RH24P3S - 24" Under Cabinet Ducted Range Hood

Avanti
Brand
Avanti
Model
RH24P3S
Type
Door Reversal Instructions: Model RH24P3S - 24" Under Cabinet Ducted Range Hood
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents