Bauknecht GSFP X285A3I User guide

Setup Instruction

Before Setup

To start, you need to download (Google Play® or AppStore®) and install the free application B-Live on your smartphone/

tablet.

The application will guide you, step by step, through the setup process.

You will need:

A wireless router, 2.4Ghz WiFi b/g/n, always connected to Internet, would be best if it supports WPS (Wi-Fi Protected Setup).

If WPS is not supported by your router, please take note of the home wireless network name (SSID) and its PASSWORD,

they will be required during the installation process.

The SAID number, which is placed on a sticker on the edge of appliance’s door and is displayed in a menu of the appliance.

Please copy the SAID number from the sticker to the table below.

SAID:

.................................................................................................................................

Before starting the installation process, please verify that the wireless signal of your home router is reaching the appliance.

Use a computer, tablet or smartphone connected only to the Wi-Fi router. Place the device close to the appliance and open

any internet web page in a browser and check that it is downloaded fast and correctly. If the internet connection of your

home is working correctly but the page is not downloaded, you may need to install a Wi-Fi extender device (not provided

with the appliance).

NOTE:

Once the installation process is comple-

ted, you can monitor the functions of your

appliances. To enable the remote control

close the door and press the button,

the indicator will light up, then you can send

commands from the application.

Automatic Setup Instruction (WPS)

You will need:

A computer or tablet connected to your home wireless network, or directly to the Internet, wireless router*) connected to

Internet and your Live Appliance’s “Smart Appliance ID” (SAID), which is printed on a label inside the door of your applian-

ce or on the side of the door.

*) Router must work at the frequency of 2.4 GHz (b/g/n)

Follow these steps:

1. On your wireless router press the WPS (Wi-Fi Protected Setup) button.

An indicator light on your router will begin to blink. If you need to, see user manual of your wireless router to learn

more.

2. On your Smart Appliance, press and hold the

button for 3 seconds. Display will show and the Wi-Fi indicator

will blink while your appliance connects to your router. When the appliance is successfully connected to local router,

display will show When the connection is successful the indicator is blinking.

When the phase is complete, a short audio feedback is played and the appliance is then connected. By default remote

control is disabled. To start remote control of your appliance press

button. Now you can refer to section Remote

management.

3. For other Smart Appliances, repeat steps for the procedure described for each. Otherwise, skip ahead to Registering

Your Appliances.

If your appliance fails to connect.

If your appliance and router fail to connect after 2 minutes, display will show

for 3 seconds and applian-

ce will go to Micro Access Point mode. Then you need to follow MANUAL SETUP INSTRUCTION.

Manual Setup Instruction

You will need:

A computer or tablet connected wirelessly to your home Wi-Fi (not with an Ethernet cable).

Your Smart Appliance’s ID (SAID), which is printed on a sticker inside the door of your appliance.

Your Smart Appliance’s MAC Address, printed on the same sticker.

Your home wireless network name (or SSID number) and your Wi-Fi password.

Follow these steps:

1. On your computer or smartphone/tablet, access your home network wireless settings and view the list of available

wireless networks. Your appliance will recieved SSID like WP_88_A1_23_B3_66_C3.

2. Select your appliance from the list. It will be identied with the characters of MAC ADDRESS but without colons (e.g.

WP_88_A1_23_B3_66_C3). You may need to refresh the list of networks.

3. In the network passphrase enter the SAID*) number removing the rst three characters (like 44444A123B).

Note: This passphrase is case sensitive, click SUBMIT, then connect to the network.

*) You may nd SAID on the label located on door edge.

4. Open a web browser. If nothing appears, type “192.168.10.1” in the address bar and press Enter. In the drop down list of

available networks, select the name of your home wireless network.

If home wireless network is hidden, select OTHER and manually enter its name and security protocol. Enter passphrase

for your home wireless network, if required, and submit.

5. Access your wireless settings and re-open the view of available wireless networks. Ensure that your computer is once

again connected to your home wireless network. If it is not, select your home wireless network and connect.

6. Proceed to REGISTRATING YOUR APPLIANCE.

Registering your appliance

You must register your Smart appliance in your account to benet from the smart features.

Download our ocial B-Live application from Google Play® or AppStore®, follow the directions to set up a new user ac-

count and add your appliance. You will need your SAID*).

*) Y6ptSAID, a 13 characters long code, on the label located on door side.

NOTE:

The application will help you to create and register your appliance to personal account.

If you replace your wireless router (or get a other Smart appliance) you will need to repeat this

setup process.

Remote management

This guide is intended to help you to properly use appliance after it was connected to the network.

This guide assumes the connection has been already established and the symbol

is lit solid on the display. Make sure

that indicator is lit on the display. Otherwise repeat setup procedure (automatically or manually).

Follow these steps:

1. Activate the remote control.

You have to enable the remote control feature by press the

button.

When the function is enabled the indicator over the

button is lit.

2. Open the door with the remote control enabled.

For safety reason when the door is opened the Remote Control function has to be automatically deactivated within 3

seconds.

To keep the remote control enabled, you should press again the

button after you have closed the door.

NOTE: The machine reminds you to reactivate the function by playing short “beeps” for a few seconds after the door

has been closed.

NOTE:

Even when Remote Control is enabled, it is

always possible to stop the cycle and to do

the drain phase by pressing and holding the

button for a few seconds.

This procedure automatically deactivate the

remote control functionality.

3. Status list

As described in section 1, when the remote function is activated the information of the status of the machine can be

checked and modied through the smartphone/tablet device.

Nevertheless, the control panel and the display describes you generic state of the appliance, according to the table on

next page.

4. Disconnecting the appliance from the network.

To disconnect and erase Wi-Fi memory, press and hold the

button for more than 10 seconds.

When the procedure is complete a long sound is heard and the connection indicator

is switched o on the display.

It will be necessary to restart the full procedure to connect it again to the network.

5. Disable the radio receiver.

To disable the radio receiver press and hold the

button for more than 5 sec.

An audio feedback is heard.

To activate radio receiver, press and hold

button for more than 3 seconds.

An audio feedback is heard.

IMPORTANT!

When the remote control function is activated,

you can interact with the appliance only from

remote control trough your smartphone/tablet.

The appliance display is then switched o and

no action on the control panel is allowed (the

machine will play short “beeps” if any button is

pressed)..

State Control panel Description

Delay

scheduled

The appliance is scheduled to

start.

Check the application to get

more information.

Cycle in

progress

The machine has started the

cycle

Check the application to get

more information.

Drain

phase in

progress

The drain is in progress, and

the cycle will end soon.

Cycle pau

sed

The machine was put in pause

from remote controler (smar-

tphone/tablet).

The cycle will be restarted

automatically.

Cycle ni

shed

The cycle is nished.

The display will then be swi-

tched o to save energy.

Failure

detected

The display shows the failure

code.

Check the application or

Reference Guide to get more

information.

Troubleshooting

How to make sure that the home Internet connection works?

Customer can check Internet Connection with tablet/smartphone (or others HAN devices as: computer and notebook).

How to make sure that your wireless functionality is on?

1) Customer can check connection with tablet/smartphone (or others HAN portable devices).

2) Customer can use a PC or smartphone to search for a network and see if his network is visible.

3) Appliance UI: Verify Wi-Fi icon state is stable ON and for the appliances with

button please active the remote control

(LED

ON).

How to nd your wireless NETWORK name and password?

See Customer Router documentation.

Suggestions: Sometime using “http://IP number” of the router the customer can access to the router setup from a connected device.

A router label usually reports login information to reach the device setup page using a connected device (PC or tablet).

How to restore the Appliance connection to the App after a home network setup change?

First step: erase the previous setup from the appliance (un-provisioning)

Dishwasher: press

button for about 10 sec to hear the 3rd beep to erase the previous setup.

Second step: provisioning appliance (repeat the installation procedure as reported on page 2).

How to set up the wireless connection on your appliance?

See detailed instruction for detail, there are two alternative approach on each appliance:

1) use the WPS (Wi-Fi Protected Setup) connection process,

2) If the appliance is not Provisioned, in the rst 20 minutes from appliance switch on it is active a web page for conguration accessible

through the network generated by the appliance (WP_”MAC Address”, example WP_88_E7_12_00_28_3C).

Which Version of WPS is supported?

Appliance supports WPS 2.0 or higher. Please, check the router documentation.

How to check if data is being transmitted?

After network set power o, wait 20 sec and power on the appliance, verify that the App shows the UI status of the appliance. Enable

remote control and check the status on the application.

Are the dierences between Android & iOS (phone and tablet version)?

There are no dierences for the appliance.

Is there the possibility to use tethering over a mobile 3G instead of a router?

Yes, but cloud services are designed for continuously connected devices.

What is the distance from router to the appliance (one room/two room)?

Normally the coverage is for few rooms but WiFi signal is strongly dependent on wall materials. Signal strength can be veried by:

1) If radio de-provisioned, customer can check connection strength with tablet/smartphone (or other HAN portable devices) close to

appliance (for example specic software tools downloadable from internet).

2) In the market there are many devices to extend the home Wi-Fi coverage as: Access Point, Wi-Fi repeaters and Power-line bridge.

3) Ensure that some other connected devices are not using all the internet bandwidth.

4) Verify that all the internet home devices don’t reach the router’s max limit for connected devices.

What settings/conguration has to be set on router software?

The router software must be enabled these options:

1) 2.4 GHz enabled, Wi-Fi b/g/n

2) DHCP and NAT activated.

Please, check the router documentation.

Which Wi-Fi protocols are supported?

Wi-Fi radio installed supports Wi-Fi b/g/n for European countries.

The indicator

blinks, application doesn’t connects to appliance.

Router has no connection with the Internet. Check router’s Internet connection with tablet/smartphone (or others HAN devices as:

computer and notebook).

Power fail, power disconnecting.

Appliance will disable remote control and will continue to work as w/o Wi-Fi connection.

Once you’ve connected appliance, it will remain linked if the power goes out, you move the appliance, or even if you put it in storage for

a while.

Failed connection with router.

If an invalid feedback is received from the router or connection timeout occurs the display will show

for 3s, then the appliance will

come back to the OFF mode and reset your Smart Appliance to the factory defaults.

Declaration

The following statements refer to the portions of this software based in part on FreeRTOS v7.0.2, http://www.freertos.org.

The use of this software is governed by the terms of GNU General Public License v. 2, which is available at:

http://www.gnu.org/licenses/gpl-2.0.html.

A copy of the source code may be obtained by written request for the software by name to opensour[email protected],

along with the address for delivery.

The following statements refer to those portions of the software copyrighted by Eclipse Foundation, Inc.

Redistribution and use in source and binary forms, with or without modication, are permitted provided that the following

conditions are met:

• Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclai-

mer.

• Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following

disclaimer in the documentation and/or other materials provided with the distribution.

• Neither the name of the Eclipse Foundation, Inc. nor the names of its contributors may be used to endorse or promote

products derived from this software without speciﬁc prior written permission.

THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED

WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR

A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE

FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES INCLUDING, BUT

NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS

INTERRUPTION HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR

TORT INCLUDING NEGLIGENCE OR OTHERWISE ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF

ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

The following statements refer to those portions of the software copyrighted by Swedish Institute of Computer Science.

Redistribution and use in source and binary forms, with or without modication, are permitted provided that the following

conditions are met:

1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclai-

mer.

2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following

disclaimer in the documentation and/or other materials provided with the distribution.

3. The name of the author may not be used to endorse or promote products derived from this software without specic

prior written permission.

THIS SOFTWARE IS PROVIDED BY THE AUTHOR “AS IS”’ AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT

NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE

DISCLAIMED. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEM

PLARY, OR CONSEQUENTIAL DAMAGES INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR

SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION HOWEVER CAUSED AND ON ANY THEORY OF

LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT INCLUDING NEGLIGENCE OR OTHERWISE ARISING IN

ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

The following statements refer to those portions of the software copyrighted by Marvell International Ltd.

DISCLAIMER.

THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED

WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR

A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE

FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES INCLUDING, BUT

NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS

INTERRUPTION HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR

TORT INCLUDING NEGLIGENCE OR OTHERWISE ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF

ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

Printed in Italy

400010784558

EC Declaration of conformity:

Whirlpool Europe S.r.l. - Socio Unico, hereby declares that this Wi-Fi enabled home appliance is in compliance with the

essential requirements and other relevant provisions of Directive 1999/5/EC of 9 March 1999 on radio equipment and

telecommunications terminal equipment and the mutual recognition of their conformity (the R&TTE Directive). A copy of

the full original declaration of conformity with the R&TTE Directive can be obtained contacting the After-sales Service (see

warranty for contacts).

Bauknecht GSFP X285A3I User guide

Related papers

Other documents