FH68-412K
User Manual
Cooker
CONTENTS
Safety information 2
Safety instructions 4
Product description 6
Before first use 7
Hob - Daily use 7
Hob - Hints and tips 8
Hob - Care and cleaning 8
Oven - Daily use 9
Oven - Using the accessories 9
Oven - Hints and tips 10
Oven - Care and cleaning 13
Troubleshooting 15
Installation 16
Energy efficiency 18
Subject to change without notice.
SAFETY INFORMATION
Before the installation and use of the appliance, carefully read
the supplied instructions. The manufacturer is not responsible
if an incorrect installation and use causes injuries and
damages. Always keep the instructions with the appliance for
future reference.
Children and vulnerable people safety
WARNING!
Risk of suffocation, injury or permanent disability.
• This appliance can be used by children aged from 8 years
and above and persons with reduced physical, sensory or
mental capabilities or lack of experience and knowledge if
they have been given supervision or instruction concerning
use of the appliance in a safe way and understand the
hazards involved.
•
Do not let children play with the appliance.
•
Keep all packaging away from children.
•
Keep children and pets away from the appliance when it
operates or when it cools down. Accessible parts are hot.
•
Cleaning and user maintenance shall not be made by
children without supervision.
General Safety
•
Only a qualified person must install this appliance and
replace the cable.
2
• Do not operate the appliance by means of an external timer
or separate remote-control system.
• Unattended cooking on a hob with fat or oil can be
dangerous and may result in fire.
• Never try to extinguish a fire with water, but switch off the
appliance and then cover flame e.g. with a lid or a fire
blanket.
• Do not store items on the cooking surfaces.
• Do not use a steam cleaner to clean the appliance.
• Metallic objects such as knives, forks, spoons and lids
should not be placed on the hob surface since they can get
hot.
• Internally the appliance becomes hot when in operation. Do
not touch the heating elements that are in the appliance.
Always use oven gloves to remove or put in accessories or
ovenware.
• Before maintenance cut the power supply.
• Ensure that the appliance is switched off before replacing
the lamp to avoid the possibility of electric shock.
•
Do not use harsh abrasive cleaners or sharp metal scrapers
to clean the glass door since they can scratch the surface,
which may result in shattering of the glass.
•
If the supply cord is damaged, it must be replaced by the
manufacturer, its Authorised Service Centre or similarly
qualified persons in order to avoid a hazard.
•
Be careful, when you touch the storage drawer. It can get
hot.
•
To remove the shelf supports first pull the front of the shelf
support and then the rear end away from the side walls.
Install the shelf supports in the opposite sequence.
•
The means for disconnection must be incorporated in the
fixed wiring in accordance with the wiring rules.
3
SAFETY INSTRUCTIONS
Installation
WARNING! Only a qualified
person must install this
appliance.
• Remove all the packaging.
• Do not install or use a damaged
appliance.
• Obey the installation instruction supplied
with the appliance.
• Always be careful when you move the
appliance because it is heavy. Always
wear safety gloves.
• Do not pull the appliance by the handle.
• The kitchen cabinet and the recess must
have suitable dimensions.
• Keep the minimum distance from the
other appliances and units.
• Make sure that the appliance is installed
below and adjacent safe structures.
• Parts of the appliance carry current.
Close the appliance with furniture to
prevent touching the dangerous parts.
• The sides of the appliance must stay
adjacent to appliances or to units with
the same height.
• Do not install the appliance on a
platform.
• Do not install the appliance adjacent to a
door or under a window. This prevents
hot cookware to fall from the appliance
when the door or the window is opened.
• Make sure to install a stabilizing means
in order to prevent tipping of the
appliance. Refer to Installation chapter.
Electrical Connection
WARNING! Risk of fire and
electrical shock.
• All electrical connections should be
made by a qualified electrician.
• The appliance must be earthed.
• Make sure that the electrical information
on the rating plate agrees with the
power supply. If not, contact an
electrician.
• Always use a correctly installed
shockproof socket.
• Do not use multi-plug adapters and
extension cables.
• Do not let mains cables touch or come
near the appliance door, especially when
the door is hot.
• The shock protection of live and
insulated parts must be fastened in such
a way that it cannot be removed without
tools.
• Connect the mains plug to the mains
socket only at the end of the installation.
Make sure that there is access to the
mains plug after the installation.
• If the mains socket is loose, do not
connect the mains plug.
• Do not pull the mains cable to
disconnect the appliance. Always pull
the mains plug.
• Use only correct isolation devices: line
protecting cut-outs, fuses (screw type
fuses removed from the holder), earth
leakage trips and contactors.
• The electrical installation must have an
isolation device which lets you
disconnect the appliance from the mains
at all poles. The isolation device must
have a contact opening width of
minimum 3 mm.
• Fully close the appliance door, before
you connect the mains plug to the mains
socket.
Use
WARNING! Risk of injury and
burns.
Risk of electrical shock.
• This appliance is for household use only.
• Do not change the specification of this
appliance.
• Make sure that the ventilation openings
are not blocked.
• Do not let the appliance stay unattended
during operation.
• Deactivate the appliance after each use.
• Be careful when you open the appliance
door while the appliance is in operation.
Hot air can release.
4
• Do not operate the appliance with wet
hands or when it has contact with water.
• Do not use the appliance as a work
surface or as a storage surface.
WARNING! Risk of fire and
explosion
• Fats and oil when heated can release
flammable vapours. Keep flames or
heated objects away from fats and oils
when you cook with them.
• The vapours that very hot oil releases
can cause spontaneous combustion.
• Used oil, that can contain food
remnants, can cause fire at a lower
temperature than oil used for the first
time.
• Do not put flammable products or items
that are wet with flammable products in,
near or on the appliance.
• Do not let sparks or open flames to
come in contact with the appliance
when you open the door.
• Open the appliance door carefully. The
use of ingredients with alcohol can
cause a mixture of alcohol and air.
WARNING! Risk of damage to
the appliance.
• To prevent damage or discoloration to
the enamel:
– do not put ovenware or other
objects in the appliance directly on
the bottom.
– do not put water directly into the hot
appliance.
– do not keep moist dishes and food
in the appliance after you finish the
cooking.
– be careful when you remove or
install the accessories.
• Discoloration of the enamel or stainless
steel has no effect on the performance
of the appliance.
• Use a deep pan for moist cakes. Fruit
juices cause stains that can be
permanent.
• Do not keep hot cookware on the
control panel.
• Do not let cookware boil dry.
• Be careful not to let objects or cookware
fall on the appliance. The surface can be
damaged.
• Do not activate the cooking zones with
empty cookware or without cookware.
• Do not put aluminium foil on the
appliance or directly on the bottom of
the appliance.
• Do not use the solid hot plate for direct
cooking. It must be used with
appropriate cookware.
• Cookware made of cast iron, aluminium
or with a damaged bottom can cause
scratches. Always lift these objects up
when you have to move them on the
cooking surface.
• This appliance is for cooking purposes
only. It must not be used for other
purposes, for example room heating.
Care and Cleaning
WARNING! Risk of injury, fire,
or damage to the appliance.
• Before maintenance, deactivate the
appliance.
Disconnect the mains plug from the
mains socket.
• Make sure the appliance is cold. There is
the risk that the glass panels can break.
• Replace immediately the door glass
panels when they are damaged. Contact
the Authorised Service Centre.
• Remaining fat or food in the appliance
can cause fire.
• Clean regularly the appliance to prevent
the deterioration of the surface material.
• Clean the appliance with a moist soft
cloth. Only use neutral detergents. Do
not use abrasive products, abrasive
cleaning pads, solvents or metal objects.
• If you use an oven spray, obey the safety
instructions on the packaging.
• Do not clean the catalytic enamel (if
applicable) with any kind of detergent.
Internal light
• The type of light bulb or halogen lamp
used for this appliance is only for
household appliances. Do not use it for
house lighting.
5
WARNING! Risk of electrical
shock.
• Before replacing the lamp, disconnect
the appliance from the power supply.
• Only use lamps with the same
specifications.
Disposal
WARNING! Risk of injury or
suffocation.
• Disconnect the appliance from the mains
supply.
• Cut off the mains cable and discard it.
• Remove the door catch to prevent
children and pets to get closed in the
appliance.
Service
• To repair the appliance contact an
Authorised Service Centre.
• Use original spare parts only.
PRODUCT DESCRIPTION
General overview
1 2 3
5
4
7
6
8
1
2
3
4
9
1
Knobs for the hob
2
Knob for the temperature
3
Temperature lamp / symbol / indicator
4
Hob lamp / symbol / indicator
5
Knob for the oven functions
6
Heating element
7
Lamp
8
Shelf support, removable
9
Shelf positions
6
Cooking surface layout
145 mm
145 mm
180 mm
180 mm
4
1 2
3
1
Cooking zone 1000 W
2
Cooking zone 1500 W
3
Cooking zone 1000 W
4
Cooking zone 2000 W
Accessories
• Wire shelf
For cookware, cake tins, roasts.
• Baking tray
For cakes and biscuits.
• Optional telescopic runners
For shelves and trays. You can order
them separately.
• Storage drawer
The storage drawer is below the oven
cavity.
BEFORE FIRST USE
WARNING! Refer to Safety
chapters.
Initial Cleaning
Remove all accessories and removable
shelf supports from the appliance.
Refer to "Care and cleaning"
chapter.
Clean the appliance before first use.
Put the accessories and the removable
shelf supports back to their initial position.
Preheating
Preheat the empty appliance to burn off the
remaining grease.
1. Set the function and the maximum
temperature.
2. Let the appliance operate for 1 hour.
3. Set the function and set the
maximum temperature. The maximum
temperature for this function is 210 °C.
4. Let the appliance operate for 15
minutes.
Accessories can become hotter than usual.
The appliance can emit an odour and
smoke. This is normal. Make sure that the
airflow in the room is sufficient.
HOB - DAILY USE
WARNING! Refer to Safety
chapters.
7
Heat setting
Sym-
bols
Function
Off position
1 - 6
Heat settings
Use the residual heat to
decrease energy consumption.
Deactivate the cooking zone
approximately 5 - 10 minutes
before the cooking process is
completed.
Turn the knob to a necessary heat setting.
The hob control indicator comes on.
To complete the cooking process, turn the
knob to the off position.
If all cooking zones are deactivated, the
hob control indicator goes out.
Using the rapid hot plate
A red dot in the middle of the plate shows a
rapid hot plate. A rapid hot plate heats up
faster than usual plates. The red dots are
painted on the plates. They can deteriorate
during use and even disappear completely
after a period of time. It does not have an
effect on the performance of the hob.
HOB - HINTS AND TIPS
WARNING! Refer to Safety
chapters.
Cookware
The bottom of the cookware
must be as thick and flat as
possible.
Examples of cooking
applications
Heat
set-
ting:
Application:
1 Keeping warm
Heat
set-
ting:
Application:
2 Gentle simmering
3 Simmering
4 Frying / browning
5 Bringing to the boil
6 Bringing to the boil / quick frying /
deep-frying
HOB - CARE AND CLEANING
WARNING! Refer to Safety
chapters.
General information
• Clean the hob after each use.
• Always use cookware with clean bottom.
• Scratches or dark stains on the surface
have no effect on how the hob operates.
Stainless steel
• For stainless steel edges of the hob use
a special cleaner applicable for the
stainless steel.
• The stainless steel edge of the plate can
change the colour as a result of high
temperature.
• Wash stainless steel parts with water,
and then dry them with a soft cloth.
8
Cleaning the electric hotplate
1. Use the cleaning powder or the
cleaning pad.
2. Clean the hob with a moist cloth and
some detergent.
3. Heat the hotplate to a low temperature
and let it dry.
4. To keep the hotplates in good shape,
rub in a sewing machine oil regularly.
Polish off the oil with absorbent paper.
OVEN - DAILY USE
WARNING! Refer to Safety
chapters.
Activating and deactivating the
appliance
It depends on the model if
your appliance has knob
symbols, indicators or lamps:
• The indicator comes on when
the oven heats up.
• The lamp comes on when
the appliance operates.
• The symbol shows whether
the knob controls one of the
cooking zones, the oven
functions or the temperature.
1. Turn the knob for the oven functions to
select an oven function.
2. Turn the knob for the temperature to
select a temperature.
3. To deactivate the appliance turn the
knobs for the oven functions and
temperature to the off position.
Safety thermostat
Incorrect operation of the appliance or
defective components can cause
dangerous overheating. To prevent this, the
oven has a safety thermostat which
interrupts the power supply. The oven
activates again automatically when the
temperature drops.
Oven functions
Sym-
bol
Oven function Application
Off position The appliance is off.
Conventional Cooking To bake and roast food on 1 shelf position.
Bottom Heat To bake cakes with crispy bottom and to preserve food.
Top Heat To brown bread, cakes and pastries. To finish cooked
dishes.
Grilling To grill flat food and to toast bread.
The maximum temperature for this function is 210 °C.
OVEN - USING THE ACCESSORIES
WARNING! Refer to Safety
chapters.
Inserting the accessories
Wire shelf:
9
Put the shelf between the guide bars of the
shelf support. The double side edges
should be at the back of the oven and point
up.
Tray:
Do not push the baking tray all
the way to the back wall of the
cavity. This prevents the heat
from circulating around the tray.
The food may be burnt,
especially in the rear part of the
tray.
Push the tray or deep pan between the
guide bars of the shelf support. Make sure
it does not touch the back wall of the oven.
OVEN - HINTS AND TIPS
WARNING! Refer to Safety
chapters.
The temperature and baking
times in the tables are guidelines
only. They depend on the
recipes and the quality and
quantity of the ingredients used.
General information
• The appliance has four shelf positions.
Count the shelf positions from the
bottom of the appliance floor.
• Moisture can condense in the appliance
or on the door glass panels. This is
normal. Always stand back from the
appliance when you open the appliance
door while cooking. To decrease the
condensation, operate the appliance for
10 minutes before cooking.
• Clean the moisture after each use of the
appliance.
• Do not put the objects directly on the
appliance floor and do not put aluminium
foil on the components when you cook.
This can change the baking results and
cause damage to the enamel.
Baking
• Your oven can bake or roast differently
to the appliance you had before. Adapt
your usual settings (temperature,
cooking times) and shelf positions to the
values in the tables.
• The manufacturer recommends that you
use the lower temperature the first time.
• If you cannot find the settings for a
special recipe, look for the one that is
almost the same.
• You can extend baking times by 10 – 15
minutes if you bake cakes on more than
one shelf position.
• Cakes and pastries at different heights
do not always brown equally at first. If
this occurs, do not change the
10
temperature setting. The differences
equalize during the baking procedure.
• With longer baking times, you can
deactivate the oven approximately 10
minutes before the end of the baking
time and then use the residual heat.
When you cook frozen food, the trays in the
oven can twist during baking. When the
trays become cold again, the distortions are
gone.
Baking cakes
• Do not open the oven door before 3/4 of
the set cooking time is up.
• If you use two baking trays at the same
time, keep one empty level between
them.
Cooking meat and fish
• Use a deep pan for very fatty food to
prevent the oven from stains that can be
permanent.
• Leave the meat for approximately 15
minutes before carving so that the juice
does not seep out.
• To prevent too much smoke in the oven
during roasting, add some water into the
deep pan. To prevent the smoke
condensation, add water each time after
it dries up.
Cooking times
Cooking times depend on the type of food,
its consistency, and volume.
Initially, monitor the performance when you
cook. Find the best settings (heat setting,
cooking time, etc.) for your cookware,
recipes and quantities when you use this
appliance.
Conventional cooking
Food Quantity
(g)
Tempera-
ture (°C)
Time (min) Shelf
posi-
tion
Accessories
Pastry stripes 250 150 25 - 30 3 baking tray
Flat cake
1)
1000 160 - 170 30 - 35 2 baking tray
Yeast cake with
apples
2000 170 - 190 40 - 50 3 baking tray
Apple pie
2)
1200 +
1200
180 - 200 50 - 60 1 2 round alumi-
nized trays (di-
ameter: 20 cm)
Small cakes
1)
500 160 - 170 25 - 30 2 baking tray
Fatless sponge
cake
1)
350 160 - 170 25 - 30 1 1 round alumi-
nized tray (diam-
eter: 26 cm)
Drip pan cake 1500 160 - 170
45 - 55
3)
2 baking tray
Chicken, whole 1350 200 - 220 60 - 70 2 wire shelf
1 baking tray
11
Food Quantity
(g)
Tempera-
ture (°C)
Time (min) Shelf
posi-
tion
Accessories
Chicken, half 1300 190 - 210 35 + 30 3 wire shelf
1 baking tray
Pork roast cut-
let
600 190 - 210 30 - 35 3 Wire shelf
1 baking tray
Flan bread
4)
800 230 - 250 10 - 15 2 baking tray
Stuffed yeast
cake
5)
1200 170 - 180 25 - 35 2 baking tray
Pizza 1000 200 - 220 25 - 35 2 baking tray
Cheese cake 2600 170 - 190 60 - 70 2 baking tray
Swiss apple
flan
5)
1900 200 - 220 30 - 40 1 baking tray
Christmas
cake
5)
2400 170 - 180
55 - 65
6)
2 baking tray
Quiche Lor-
raine
5)
1000 220 - 230 40 - 50 1 1 round tray (di-
ameter: 26 cm)
Peasant
bread
7)
750 + 750 180 - 200 60 - 70 1 2 aluminized
trays (length: 20
cm)
Romanian
sponge cake
1)
600 + 600 160 - 170 40 - 50 2 2 aluminized
trays (length: 25
cm) on the same
shelf position
Romanian
sponge cake -
traditional
600 + 600 160 - 170 30 - 40 2 2 aluminized
trays (length: 25
cm) on the same
shelf position
Yeast buns
5)
800 200 - 210 10 - 15 2 baking tray
Swiss roll
1)
500 150 - 170 15 - 20 1 baking tray
Meringue 400 100 - 120 40 - 50 2 baking tray
Crumble
cake
5)
1500 180 - 190 25 - 35 3 baking tray
Sponge cake
1)
600 160 - 170 25 - 35 3 baking tray
12
Food Quantity
(g)
Tempera-
ture (°C)
Time (min) Shelf
posi-
tion
Accessories
Buttered
cake
1)
600 180 - 200 20 - 25 2 baking tray
1)
Preheat the oven for 10 minutes.
2)
Preheat the oven for 15 minutes.
3)
After you switch off the appliance, leave the cake in the oven for 7 minutes.
4)
Preheat the oven for 20 minutes.
5)
Preheat the oven for 10 - 15 minutes.
6)
After you switch off the appliance, leave the cake in the oven for 10 minutes.
7)
Set the temperature for 250 °C and preheat the oven for 18 minutes.
OVEN - CARE AND CLEANING
WARNING! Refer to Safety
chapters.
Notes on cleaning
• Clean the front of the appliance with a
soft cloth with warm water and a
cleaning agent.
• To clean metal surfaces, use a usual
cleaning agent.
• Clean the appliance interior after each
use. Fat accumulation or other food
remains may result in a fire.
• Clean stubborn dirt with a special oven
cleaner.
• Clean all accessories after each use and
let them dry. Use a soft cloth with warm
water and a cleaning agent.
• If you have nonstick accessories, do not
clean them using aggressive agents,
sharp-edged objects or a dishwasher. It
can cause damage to the nonstick
coating.
Stainless steel or aluminium
appliances
Clean the oven door with a wet
sponge only. Dry it with a soft
cloth.
Do not use steel wool, acids or
abrasive materials as they can
damage the oven surface. Clean
the oven control panel with the
same precautions.
Removing the shelf supports
To clean the oven, remove the shelf
supports.
1.
Pull the front of the shelf support away
from the side wall.
2. Pull the rear end of the shelf support
away from the side wall and remove it.
13
2
1
Install the shelf supports in the opposite
sequence.
Removing and installing the
oven glass panels
You can remove the internal glass panels to
clean it. The number of glass panels is
different for different models.
WARNING! Keep the oven door
slightly open during the cleaning
process. When you open it fully
it may accidentally close causing
potential damage.
WARNING! Do not use the
appliance without the glass
panels.
1. Open the door until it is at an angle of
approximately 30°. The door stands
alone when slightly open.
30°
2. Hold the door trim (B) at the top edge of
the door on both sides and push
inwards to release the clip seal.
1
2
B
3. Pull the door trim to the front to remove
it.
WARNING! When you take
out the glass panels the
oven door tries to close.
4.
Hold the top edge of the door glass
panels and pull them up one by one.
5.
Clean the glass panel with water and
soap. Dry the glass panel carefully.
When the cleaning is complete, install the
glass panels and the oven door. Do the
above steps in the opposite sequence.
Install the smaller panel first, then the larger.
CAUTION! The screen with a
printing on the inner glass panel
must face the inner side of the
door.
CAUTION! Make sure that after
installation the surface of the
frame of the glass panel on the
screen with a printing is not
rough when you touch it.
CAUTION! Make sure that you
install the internal glass panel in
the appropriate seats.
Removing the drawer
WARNING! Do not keep
flammable items (such as
cleaning materials, plastic bags,
oven gloves, paper or cleaning
sprays) in the drawer. When you
use the oven, the drawer can
become hot. There is a risk of
fire.
The drawer below the oven can be
removed for cleaning.
1. Pull the drawer out until it stops.
14
2. Slowly lift the drawer.
3.
Pull the drawer out fully.
To install the drawer, do the above steps in
the opposite sequence.
Replacing the lamp
Put a cloth on the bottom of the interior of
the appliance. It prevents damage to the
lamp glass cover and the cavity.
WARNING! Danger of
electrocution! Disconnect the
fuse before you replace the
lamp.
The lamp and the lamp glass
cover can be hot.
1. Deactivate the appliance.
2. Remove the fuses from the fuse box or
deactivate the circuit breaker.
The back lamp
1. Turn the lamp glass cover
counterclockwise to remove it.
2.
Clean the glass cover.
3.
Replace the lamp with a halogen, 230
V, 40 W, 300 °C heat resistant lamp.
4.
Install the glass cover.
TROUBLESHOOTING
WARNING! Refer to Safety
chapters.
What to do if...
Problem Possible cause Remedy
You cannot activate the ap-
pliance.
The appliance is not connec-
ted to an electrical supply or
it is connected incorrectly.
Check if the appliance is cor-
rectly connected to the elec-
trical supply.
You cannot activate or oper-
ate the hob.
The oven does not heat up.
The fuse is released. Make sure that the fuse is the
cause of the malfunction. If
the fuse releases again and
again, contact a qualified
electrician.
You cannot activate or oper-
ate the hob.
The fuse is released. Activate the hob again and
set the heat setting in less
than 10 seconds.
The lamp does not operate. The lamp is defective. Replace the lamp.
Steam and condensation set-
tle on the food and in the
cavity of the oven.
You left the dish in the oven
for too long.
Do not leave the dishes in the
oven for longer than 15 - 20
minutes after the cooking
process ends.
15
Problem Possible cause Remedy
The oven does not heat up. The necessary settings are
not set.
Make sure that the settings
are correct.
It takes too long to cook the
dishes or they cook too
quickly.
The temperature is too low or
too high.
Adjust the temperature if
necessary. Follow the advice
in the user manual.
Service data
If you cannot find a solution to the problem
yourself, contact your dealer or an
Authorised Service Centre.
The necessary data for the service centre is
on the rating plate. The rating plate is on
the front frame of the appliance cavity. Do
not remove the rating plate from the
appliance cavity.
We recommend that you write the data here:
Model (MOD.) .........................................
Product number (PNC) .........................................
Serial number (S.N.) .........................................
INSTALLATION
WARNING! Refer to Safety
chapters.
Location of the appliance
You can install your freestanding appliance
with cabinets on one or two sides and in
the corner.
For minimal distances for fitting check the
table.
A
C
B
Minimum distances
Dimension mm
A
400
B
650
C
150
16
Technical data
Voltage 400 V
Frequency 50 Hz
Appliance class 1
Dimension mm
Height 855
Width 500
Depth 600
Levelling of the appliance
Use small feet on the bottom of appliance
to set the appliance top surface level with
other surfaces.
Anti-tilt protection
Set the correct height and area for the
appliance before you attach the anti-tilt
protection.
CAUTION! Make sure you
install the anti-tilt protection at
the correct height.
Make sure that the surface
behind the appliance is smooth.
You must install the anti-tilt protection. If
you do not install it, the appliance can tilt.
Your appliance has the symbol shown on
the picture (if applicable) to remind you
about the installation of the anti-tilt
protection.
1. Install the anti-tilt protection 317 - 322
mm down from the top surface of the
appliance and 80 - 85 mm from the
side of the appliance into the circular
hole on a bracket. Screw it into the solid
material or use applicable reinforcement
(wall).
80-85
mm
317-322
mm
17
2. You can find the hole on the left side at
the back of the appliance. Lift the front
of the appliance and put it in the middle
of the space between the cupboards. If
the space between the bench
cupboards is larger than the width of
the appliance, you must adjust the side
measurement to centre the appliance.
If you changed the dimensions
of the cooker, you must align
the non-tip device correctly.
CAUTION! If the space
between the bench cupboards
is larger than the width of the
appliance, you must adjust the
side measurement to the centre
of the appliance.
Electrical installation
WARNING! The manufacturer is
not responsible if you do not
follow the safety precautions
from Safety chapters.
This appliance is supplied without a main
plug or a main cable.
Applicable cable type: H05 RR-F with
adequate cross-section.
WARNING! Before you connect
the mains cable to the terminal,
measure the voltage between
phases in the house network.
Then, refer to the connection
label at the back of the
appliance to use the correct
electrical installation. This order
of steps prevents from
installation errors and damage
to the electrical components of
the appliance.
WARNING! The power cable
must not touch the part of the
appliance shown in the
illustration.
ENERGY EFFICIENCY
Product information for hob according to EU 66/2014
Model identifi-
cation
FH68-412K
Type of hob Hob inside Freestanding Cooker
Number of
cooking zones
4
Heating tech-
nology
Solid Hot Plate
Diameter of
circular cook-
ing zones (Ø)
Left rear
Right rear
Right front
Left front
14.5 cm
18.0 cm
14.5 cm
18.0 cm
18
Energy con-
sumption per
cooking zone
(EC electric
cooking)
Left rear
Right rear
Right front
Left front
197.5 Wh/kg
198.5 Wh/kg
197.5 Wh/kg
196.0 Wh/kg
Energy consumption of the hob (EC electric hob) 197.4 Wh/kg
EN 60350-2 - Household electric cooking
appliances - Part 2: Hobs - Methods for
measuring performance.
Hob - Energy saving
You can save energy during everyday
cooking if you follow below hints.
• When you heat up water, use only the
amount you need.
• If it is possible, always put the lids on the
cookware.
• Before you activate the cooking zone
put the cookware on it.
• The cookware bottom should have the
same diameter as the cooking zone.
• Put the smaller cookware on the smaller
cooking zones.
• Put the cookware directly in the centre
of the cooking zone.
• Use the residual heat to keep the food
warm or to melt it.
Product Fiche and information for ovens according to EU
65-66/2014
Supplier's name Novamatic
Model identification FH68-412K
Energy Efficiency Index 105.0
Energy efficiency class A
Energy consumption with a standard load, conventional
mode
0.84 kWh/cycle
Number of cavities 1
Heat source Electricity
Volume 60 l
Type of oven Oven inside Freestanding Cooker
Mass 42.0 kg
EN 60350-1 - Household electric cooking
appliances - Part 1: Ranges, ovens, steam
ovens and grills - Methods for measuring
performance.
Oven - Energy saving
The appliance contains features which help
you save energy during everyday cooking.
• General hints
– Make sure that the oven door is
closed properly when the appliance
operates and keep it closed as much
as possible during the cooking.
– Use metal dishes to improve the
energy saving.
– When possible, put the food inside
the oven without heating it up.
19
– When the cooking duration is longer
than 30 minutes, reduce the oven
temperature to minimum, 3 - 10
minutes before the end of the
cooking time, depending on the
duration of the cooking. The residual
heat inside the oven will continue to
cook.
– Use the residual heat to warm up
other foods.
• Keep food warm - if you want to use
the residual heat to keep the meal warm,
choose the lowest possible temperature
setting.
WARRANTY / CUSTOMER SERVICE
For each product we provide a two-year
guarantee from the date of purchase or
delivery to the consumer (with a guarantee
certificate, invoice or sales receipt serving
as proof).
The guarantee covers the costs of
materials, labour and travel. The guarantee
will lapse if the operating instructions and
conditions of use are not adhered to, if the
product is incorrectly installed, or in the
event of damage caused by external
influences, force majeure, intervention by
third parties or the use of non-genuine
components.
CONDITIONS DE GARANTIE / SERVICE
Nous octroyons sur chaque produit 2 ans
de garantie à partir de la date de livraison
ou de la mise en service au consommateur
(documenté au moyen d’une facture, d’un
bon de garantie ou d’un justificatif d’achat).
Notre garantie couvre les frais de mains
d’oeuvres et de déplacement, ainsi que les
pièces de rechange.
Les conditions de garantie ne sont pas
valables en cas d’intervention d’un tiers non
autorisé, de l’emploi de pièces de rechange
non originales, d’erreurs de maniement ou
d’installation dues à l’inobservation du
mode d’emploi, et pour des dommages
causés par des influences extérieures ou de
force majeure.
GARANTIEBEDINGUNGEN / KUNDENDIENST
Für jedes Produkt gewähren Wir ab Verkauf
bzw. Lieferdatum an den Endverbraucher
eine Garantie von 2 Jahren. (Ausweis durch
Garantieschein, Faktura oder
Verkaufsbeleg).
Die Garantieleistung umfasst die Kosten für
Material, Arbeits- und Reisezeit.
Die Garantieleistung entfällt bei
Nichtbeachtung der Gebrauchsanweisung
und Betriebsvorschriften, unsachgerechter
Installation, sowie bei Beschädigung durch
äussere Einflüsse , höhere Gewalt, Eingriffe
Dritter und Verwendung von Nicht-Original
Teilen.
CONDIZIONI DI GARANZIA / SERVIZIO CLIENTELA
Per ogni prodotto concediamo una
garanzia di 2 anni a partire dalla data di
consegna o dalla sua messa in funzione.
(Fa stato la data della fattura, del certificato
di garanzia o dello scontrino d’acquisto)
Nella garanzia sono comprese le spese di
manodopera, di viaggio e del materiale.
Dalla copertura sono esclusi il logoramento
ed i danni causati da agenti esterni,
intervento di terzi, utilizzo di ricambi non
originali o dalla inosservanza delle
20
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI