1
Quick Start Guide
6
3. Hold your microSDHC card with the
metal contacts facing down and slide
it into the microSDHC card slot.
4. Align the connectors on the phone
and the battery and slide the battery
into the compartment. Then gently
press the battery down until it is
secured.
5. Align the back cover with the back of
the phone and press the cover back
into place. Make sure all the tabs are
secure and there are no gaps around
the cover.
5
Starting Up
Switch off your phone before installing or
replacing the battery or the SIM card.
The microSDHC™ card is optional and
can be installed and removed while the
phone is turned on. Unmount the
microSDHC card before removing it.
1. Place your finger in the slot at the
bottom of the back cover to lift and
remove the cover.
2. Hold the SIM card with its cut corner
oriented as shown and slip it into the
card holder.
4
Power Key
Press and hold to power on, select
phone modes, turn on/off airplane
mode, or power off.
Press to turn off or on the screen
display.
Home Key
Touch to return to the home screen
from any application or screen.
Menu Key
Touch to get the options for the
current screen.
Touch and hold to see recently used
applications.
Back Key
Touch to go to the previous screen.
Volume Key
Press or hold to turn the volume up or
down.
3
2
Getting to Know Your
Phone
7
Charging the Battery
1. Connect the adapter to the charging
jack. Ensure that the adapter is
inserted with the correct orientation.
Do not force the connector into the
charging jack.
2. Connect the charger to a standard AC
power outlet.
3. Disconnect the charger when the
battery is fully charged.
Indicator
Earpiece
Front Camera
Headset Jack
Menu KeyBack Key
Touch Screen
Volume Key Power Key
Home Key
Back Cover
Camera
Charging/ USB Jack
8
Powering On/Off Your
Phone
Make sure the battery is charged before
powering on.
Press and hold the Power Key to
turn on your phone.
To turn it off, press and hold the
Power Key to open the options
menu. Touch Power off > OK.
13
EMC
EN 301 489-1
V1.9.2:2011
EN 301 489-7
V1.3.1: 2005
EN 301 489-3
V1.6.1;2012
EN 301489-17
V V2.2.1
:2012
EN 301 489
-24 V1.5.1
:2010
I15D00069
-EMC
Radio
Spectrum
EN 301 511
V9.0.2
EN301
908-1/-2
V6.2.1
EN 300 328
V1.8.1
EN 300 440-1
V1.6.1
EN 300 440-2
V1.4.1
I15D00069
-RFG
I15D00069
-RFW
BL-SZ1560
085-601
BL-SZ1560
085-602
I15D00069
-RFB
I15D00069
-WLA
I15D00069
-GPS
RoHS
IEC
62321:2008
+2013
150600035
SHA-001
ErP
(EC) No
278/2009
TRS110100
58
12
PHOENIX TESTLAB GmbH (Notified Body
No.0700) and assessment of compliance
of the product with the requirements
relating to Directive 2011/65/EU was
performed by Intertek Testing Services
Ltd., Shanghai and Directive
2009/125/EC was performed by
Shenzhen Huatongwei International
Inspection Co.,Ltd. The assessments
were based on the following regulations
and standards:
Requirement Standard Report No.
EN 62209-
1:2006 ,
EN 62209-
2:2010
EN 50360:
2001/A1:2012
EN 50566:
2013/AC:2014
EN 62479
:2010
EN 62311
:2008
I15D00069
-SAR
Health and
safety
EN 60950
-1:2006
+A11:2009
+A1:2010+A1
2:2011
EN 50332-1
-2000;
EN50332
-2-2003
I15D00069
-SAF
I15D00069
-ACO
11
EC DECLARATION OF
CONFORMITY
It is hereby declared that following
designated product:
Product Type: WCDMA/GSM(GPRS)
Dual-Mode Digital Mobile Phone
Model No: ZTE Blade C320/ Blade C320
Product Description: WCDMA/GSM
(GPRS) Dual-Mode Digital Mobile Phone
Complies with the essential protection
requirements of Directives on Radio and
Telecommunication Terminal Equipment
(Directive 1999/5/EC)，Restriction of the
Certain Hazardous Substances in
electrical and electronic equipment
(Directive 2011/65/EU), Eco-design
Requirements for Energy-Related
Products (Directive 2009/125/EC) and
their amendments.
This declaration applies to all specimens
manufactured identical to the samples
submitted for testing/evaluation.
Assessment of compliance of the product
with the requirements relating to
Directive 1999/5/EC was performed by
10
Do not use while re-fuelling
This device may produce a
bright or flashing light
Do not dispose of it in a fire
To prevent possible
hearing damage, do not
listen at high volume levels
for long periods.
Avoid Extreme
Temperatures
Avoid any contact with
liquid, keep it dry
Do not attempt to
disassemble
Only use approved
accessories
Do not rely on this device
for emergency
communications
9
Product Safety
Information
Do not use hand-held while
driving
For body-worn operation
maintain a separation of 15
mm
Small parts may cause a
choking hazard
This device may produce a
loud sound
Avoid contact with
magnetic media
Keep away from
pacemakers and other
personal medical devices
Switch off when instructed
in hospitals and medical
facilities
Switch off when instructed
in aircrafts and airports
Switch off in explosive
environments
14
This declaration is the responsibility of
the manufacturer:
ZTE Corporation
ZTE Plaza, Keji Road South, Hi-Tec h,
Industrial Park, Nanshan District,
Shenzhen, Guangdong, 518057,
P.R.China
Authorised person signing for the
company:
Yao cuifeng Chief Quality Officer
Of ZTE Corporation
Name in block letters & position in the
company
Shenzhen, 2 July 2015
Place & date Legally valid signature
-
1
-
2
