bora PKCH3 1xx User manual

bora
Brand
bora
Model
PKCH3 1xx
Category
Hobs
Type
User manual
EN
PKCH3UMIMEN-100
www.bora.com
Operating and installation instructions PKCH3
BORA Pro Hyper cooktop 1-ring/2-ring
1.
2.
2.
1044094 - 36
EN
2
www.bora.com
5.6.3 Fitting the control knob .......................................................18
5.7 Installing the cooktops .......................................................18
5.7.1 Installing the cooktop ..........................................................18
– Inserting the cooktop (ports on the front) ......................... 18
– Levelling the cooktop (if necessary) .................................. 19
– Securing the cooktop ........................................................ 19
5.7.2 Installation rotated by 180°
(alternative installation variation) ........................................19
5.8 Establishing communication and power connection ......20
5.8.1 Connecting the control knobs ............................................. 20
– Connecting the control knobs to the cooktop................... 20
5.8.2 Establishing contact between the
cooktop extractor and cooktops .........................................21
5.8.3 Connecting the power supply .............................................. 21
– Connecting the cooktop to the power supply ................... 21
5.9 Basic configuration ............................................................22
5.10 Initial operation ...................................................................22
5.11 Function test ........................................................................22
5.12 Sealing the appliances .......................................................22
5.13 Handover to user ................................................................22
6 Functions and operation 23
6.1 Knob operation .................................................................... 23
– Operating the knob ring .................................................... 23
– Operating the touch surface ............................................. 23
6.2 Switching the system on and off ......................................23
– Switching on ..................................................................... 23
– Switching off ..................................................................... 23
6.3 Operating the cooktops......................................................24
6.3.1 General operating instructions for cooktops ......................24
6.3.2 Setting cooking zone power levels ...................................... 24
– Increasing the power level ................................................. 24
– Reducing the power level .................................................. 24
6.3.3 Cooktop power setting ........................................................24
6.4 Function menu ....................................................................24
– Calling up the function menu ............................................ 24
6.4.1 Additionalringswitching–2-ring,3-ring,roaster ............... 25
– Activating additional rings
(2-ring/3-ring additional switching) ................................... 25
– Deactivating additional rings ............................................. 25
6.4.2 Variable heat retention function ..........................................25
– Activating the heat retention function ............................... 25
– Increasing or reducing the active heat retention level ....... 26
– Deactivating the heat retention function ........................... 26
6.4.3 Timerfunction/automaticcut-off .......................................26
– Activating cooking zone timers ......................................... 26
– Setting the time and starting the timer ............................. 26
– Changing active timers ...................................................... 27
– Switching the timer off early ............................................. 27
– Time lapsed ....................................................................... 27
6.4.4 Automatic heat up function .................................................27
– Activating the automatic heat up function......................... 27
– Deactivating the automatic heat up function early ............ 27
– Time lapsed ....................................................................... 27
1 General information 4
1.1 Liability ................................................................................... 4
1.2 Validity of the operating and installation instructions ...... 4
1.3 Product conformity ............................................................... 4
1.4 Data protection .....................................................................4
1.5 Presentation of information ................................................. 4
2 Safety 5
2.1 Use as intended ....................................................................5
2.2 People with limited abilities ................................................. 5
2.3 General safety instructions ..................................................5
2.4 Safety instructions for installation ...................................... 6
2.5 Safety instructions – operation ...........................................7
2.6 Safety instructions – cleaning and maintenance .............. 9
2.7 Safety instructions –
repairs, servicing and spare parts
... 9
2.8 Safety instructions – disassembly and disposal ...............9
3 Technical data 10
3.1 BORA Pro Hyper cooktop 1-ring/2-ring PKCH3 ..............10
3.2 BORA Professional 3.0 control knob dimensions............10
4 Appliance description 11
4.1 Control knob ........................................................................11
– How it works ..................................................................... 11
– Structure ........................................................................... 11
– Operating elements ........................................................... 11
– Control knob display ......................................................... 11
– Control knob assignment .................................................. 11
4.2 Cooktop appliance description ..........................................12
– Display and symbols.......................................................... 12
– Layout and size of the cooking zones ............................... 12
4.2.1 How the Hyper and HiLight cooktops work
(PKC3,PKCB3,PKCH3) ........................................................12
– Power levels ...................................................................... 12
– Suitable cookware ............................................................. 12
4.3 Safety devices .....................................................................13
– Safety shut-down .............................................................. 13
– Residual heat indicator ...................................................... 13
– Overheating protection ...................................................... 13
– Childproofing feature......................................................... 13
5 Installation 14
5.1 General installation instructions ......................................14
5.2 Checking the scope of delivery .........................................14
5.3 Tools and aids ...................................................................... 14
5.4 Assembly instructions ........................................................15
5.4.1 Safety clearances.................................................................15
5.4.2 Minimuminstallationdimensions(standardset-up) ........... 15
5.4.3 Worktop and kitchen units ..................................................15
5.5 Cut-out dimensions .............................................................16
5.5.1 Flush installation .................................................................. 16
5.5.2 Surface mounting ................................................................16
5.6
Installing the control knob in the floor unit front panel
...17
5.6.1 Cooktop bore holes .............................................................17
5.6.2 Example bore holes .............................................................17
Table of Contents
EN
3
www.bora.com
7 Cleaning and maintenance 28
7.1 Cleaning agents ................................................................... 28
– Cleaning products for glass ceramic cooktops ................. 28
7.2 Cleaning the cooktops ........................................................ 28
7.2.1 Cleaning glass ceramic cooktops ........................................28
7.3 Looking after your cooktops .............................................. 28
7.4 Cleaning the control knobs ................................................ 29
– Cleaning the knob ring ...................................................... 29
– Cleaning the touch surface and the knob housing ............ 29
8 Troubleshooting 30
9 Decommissioning, disassembly and
disposal 31
9.1 Decommissioning ...............................................................31
9.2 Disassembly ........................................................................31
9.3 Environmentally-friendly disposal .....................................31
10 Warranty, technical service,
spare parts, accessories 32
10.1 BORA manufacturer’s warranty .........................................32
10.2 Service .................................................................................32
10.3 Spare parts ..........................................................................32
10.4 Accessories .......................................................................... 32
11 Notes 33
EN
4
General information
www.bora.com
1 General information
1.5 Presentation of information
We use standard formatting, numbering, symbols, safety
instructions, terms and abbreviations so that you can work
quickly and safely when using this manual.
The term “appliance” is used to refer to cooktops, cooktop
extractors or cooktops with integrated cooktop extractor.
Instructions are indicated with an arrow.
XX
Always follow all instructions in the prescribed order.
Enumerations are indicated with a bullet point at the start of
the line:
XO
Enumeration 1
XO
Enumeration 2
i
Information notes point to special features that must be
taken into account.
Safety and warning instructions
The safety and warning instructions in this manual are
emphasised with symbols and signal words.
Safety and warning instructions are structured as follows:
ÿ
WARNING SYMBOL AND SIGNAL WORD!
Type and source of danger
Resultsofnon-compliance
XX
Measures to minimise risk
Please note:
XO
warning symbols draw attention to a high risk of injury.
XO
The signal word indicates the severity of that risk.
Warning
symbol
Signal word Risk
ü
Danger Indicates an immediate, hazardous
situation which causes death or
serious injury if not respected.
ü
Warning Indicates a potentially hazardous
situation which can cause death or
serious injury if not respected.
Caution Indicates a potentially hazardous
situation which can cause minor
injury or damage to property if not
respected.
Tab. 1.1 Meaning of the warning symbols and signal words
These instructions contain important information to protect you
from injury and prevent damage to the appliance.
Please read these instructions carefully before installing or using
the appliance for the first time.
Other documents apply alongside these instructions.
Please by all means adhere to all documents that form part of
the scope of delivery.
Assembly and installation may only be carried out by trained
specialists and taking into account the applicable laws,
regulations and standards. All safety and warning information
as well as the handling instructions in the accompanying
documents must be observed.
1.1 Liability
BORA Holding GmbH, BORA Vertriebs GmbH & Co KG, BORA
APAC Pty Ltd and BORA Lüftungstechnik GmbH – hereinafter
referred to as BORA – does not assume any liability for damage
arising from disregard for or non-adherence to the documents
included in the scope of delivery!
Furthermore, BORA shall not be held liable for damage caused
by improper installation or failure to observe the safety and
warning instructions!
1.2 Validity of the operating and
installation instructions
These instructions apply to several appliance versions. It is
therefore possible that some of the features described do not
apply to your appliance. The details of the figures contained
herein may differ from some appliance versions and are to be
understood as schematic diagrams.
1.3 Product conformity
Directives
The appliances meet the following EU/EC directives:
2014/30/EU EMC Directive
2014/35/EU Low Voltage Directive
2009/125/EC Ecodesign Directive
2011/65/EU RoHS Directive
1.4 Data protection
During operation your cooktop extractor saves pseudonymised
data such as menu settings entered by you, operating hours
of the individual technical units and the number of functions
selected. Furthermore, your cooktop extractor documents errors
in combination with the number of operating hours.
Data can only be read out manually via your cooktop extractor.
This decision is therefore your responsibility.
These saved data then enable a rapid error search and
troubleshooting in the event of servicing.
EN
5
Safety
www.bora.com
2 Safety
People with reduced physical, sensory or
mental capacities
The appliance can be used by people with reduced
physical, sensory or mental capacities or a lack of
experience and/or knowledge if they are supervised
or have been instructed how to use the appliance
safely and understand the resultant risks. Operation
can be restricted using the childproofing feature.
ÿ
DANGER!
Risk of burns from hot cookware and food
Handles projecting over the edge of the worktop
are asking to be grabbed.
XX
Keep children away from hot cooking zones or
ensure they are supervised at all times.
XX
Do not turn pot and pan handles so they stick
out beyond the worktop.
XX
Make sure that hot pots and pans cannot be
pulled down.
XX
Ifnecessary,usesuitablestoveguardsor
covers.
XX
Only use stove guards and covers that are
approved by the appliance manufacturer;
otherwise,thereisariskofaccidents.
XX
Tochooseasuitablestoveguard,contactyour
specialistsupplierortheBORAServiceTeam.
2.3 General safety instructions
ÿ
DANGER!
Packaging components are a choking hazard
Packagingcomponents(e.g.lm,polystyrene)can
belife-threateningforchildren.
XX
Store all packaging components out of reach of
children.
XX
Dispose of the packaging properly and
immediately.
The appliance complies with the stipulated safety
requirements. The user is responsible for the safe
use of the appliance, cleaning and maintenance.
Improper use can lead to personal injury and damage
to property.
2.1 Use as intended
The appliance is solely intended for preparing food in
private households.
This appliance is not intended for:
XO
outdoor use
XO
heating rooms
XO
cooling, ventilating or dehumidifying rooms
XO
use in mobile installation sites such as motor
vehicles, ships or aeroplanes
XO
use with an external timer or a separate remote
control system (except for emergency shutdown)
XO
use at altitudes of over 2,000 m (metres above sea
level).
Any other use or any use that goes beyond that which
is described here is classed as unintended.
i
BORAdoesnotassumeanyliabilityfor
damages caused by improper use or incorrect
operation.
All misuse is prohibited!
2.2 People with limited abilities
Children
The appliance can be used by children aged 8 and
over if they are supervised or have been instructed
how to use the appliance safely and understand
the resultant risks. Children must not play with the
appliance.
XX
Use the childproofing feature in order to prevent
children from switching on the appliance or
changing the settings when they are unattended.
XX
Supervise children in the vicinity of the appliance.
XX
Do not store any items that could be of interest to
children in storage spaces above or behind the
appliance. Otherwise, they will be tempted to
climb onto the appliance.
i
Any work involving cleaning and maintenance
must not be carried out by children unless they
are supervised at all times while doing so.
EN
6
Safety
www.bora.com
CAUTION!
Risk of injury from heavy lifting
Ifnothandledcorrectly,carryingandinstalling
appliances can cause injury to the limbs or torso.
XX
Ifnecessary,carryandinstalltheappliancewith
another person.
XX
Use appropriate aids to prevent damage or
injury.
CAUTION!
Damage from improper use
The appliance surfaces must not be used as
work or storage surfaces. This can damage the
appliances (particularly in the case of hard and
sharp objects).
XX
Never use the appliances as work or storage
surfaces.
XX
Keep hard or sharp objects away from the
appliance surfaces.
Faults and errors
XX
In the case of faults and errors, follow the
instructions in the “Troubleshooting” chapter.
XX
In the event of any faults or errors that are not
mentioned, switch the appliance off and contact
BORA Service.
Pets
XX
Keep pets away from the appliance.
2.4 Safety instructions for
installation
i
The appliance must only be installed and
assembled by trained specialists who are
familiar with and comply with the standard
national regulations and supplementary
regulations of the local utility companies.
i
During installation maintain the minimum
clearance stated in the “Installation” (“Safety
clearances”) chapter.
i
Work on electrical components must only be
conducted by trained electrical personnel.
The electrical safety of the appliance is only
guaranteed if it is connected to a protective
conductor system that has been installed in line with
regulations. Ensure that this basic safety precaution
is met.
ÿ
DANGER!
Risk of electric shock or injury from damaged
surfaces
The underlying electronics can be exposed or
damagedduetossures,fracturesorcracksin
appliancesurfaces(e.g.damagedglassceramic),
particularly in the operating area. This can cause
anelectricshock.Furthermore,adamagedsurface
can cause injuries.
XX
Do not touch the damaged surface.
XX
Ifthereareanycracks,fissuresorfractures,
switch the appliance off immediately.
XX
Safely disconnect the appliance from the mains
usingtheLSswitch,fuses,automaticcircuit
breakers or contactor.
XX
ContactBORAService.
ÿ
WARNING!
Risk of injury from damaged components
Damaged components that cannot be removed
without tools can cause injuries.
XX
Try not to repair or replace damaged
components yourself.
XX
ContactBORAService.
ÿ
WARNING!
Risk of injury or damage due to incorrect
components or unauthorised modifications
Incorrect components can lead to personal
injuryordamagetotheappliance.Modications,
additions or alterations to the appliance can lead to
safety risks.
XX
Only use original components.
XX
Donotmakeanymodifications,additionsor
alterations to the appliance.
CAUTION!
Appliance components can cause injury if
dropped
Appliancecomponents(e.g.pansupports,
operatingcontrols,covers,greaselters,etc.)can
cause injury if dropped.
XX
Place any appliance components that have been
removed in a safe place near the appliances.
XX
Ensure that no components removed from the
appliances can fall on the floor.
EN
7
Safety
www.bora.com
The appliance must be suitable for the regional
voltage and frequency.
XX
Check the information on the identification plate
and in the event of deviations, do not connect the
appliance.
XX
Conduct all work extremely attentively and
conscientiously.
XX
Do not connect the appliance to the mains until
the duct system has been installed or the
recirculation filter has been fitted.
XX
Only use the connection cables supplied. Where
necessary these are included in the scope of
delivery.
XX
Do not use the appliance until installation is
complete. This is the only way to ensure safe
operation.
ÿ
DANGER!
Risk of electric shock from damaged appliance
A damaged appliance can cause an electric shock.
XX
Check the appliance for visible damage prior to
installation.
XX
Do not install or connect any damaged
appliances.
XX
Do not operate any damaged appliances.
CAUTION!
Risk of burning from control knobs that are
not positioned optimally.
If the control knobs are not installed in a suitable
place,duringoperationthereisariskofsustaining
burns from the cooktop surface.
XX
Onlyinstallthecontrolknobsinasuitableplace,
which is practical and safe.
2.4.1 Safety instructions for cooktop
installation
ÿ
DANGER!
Risk of electric shock from incorrect mains
connection
Connecting the appliance to the mains incorrectly
poses a risk of electric shock.
XX
Make sure that the appliance has a fixed
connection to the mains voltage.
XX
Make sure that the appliance is connected to a
properly installed protective conductor system.
XX
Make sure that technical equipment is provided
to enable all of the appliance’s poles to be
disconnected from the mains with a contact
opening width of at least 3 mm (LS switch and
automaticcircuitbreakers,fuses,contactor).
ÿ
DANGER!
Risk of electric shock from damaged power
supply cable
If the power supply cable is damaged (e.g. during
installation or by coming into contact with hot
cookingsurfaces),thiscancausean(lethal)
electric shock.
XX
Make sure that the power supply cable does not
become trapped or damaged.
XX
Make sure that the power supply cable does not
come into contact with hot cooking surfaces.
2.5 Safety instructions – operation
XX
Make sure that the base of the cookware as well
as the appliance surfaces are clean and dry.
XX
Always lift (do not drag) cookware to prevent
scratching and abrasion on the appliance surface.
XX
Do not use the appliance as a storage surface.
XX
Switch off the appliance after use.
EN
8
Safety
www.bora.com
ÿ
WARNING!
Risk of burning from hot appliances
Certain appliances and their exposed parts become
hot during use (e.g. cooktops). They should be
left to cool down completely after switching off.
Touching hot surfaces can cause serious burns.
XX
Do not touch hot appliances.
XX
Pay attention to the residual heat indicator.
ÿ
WARNING!
Risk of burning and fire from hot objects
The appliance and its exposed parts are hot during
operation and the cooling phase. Objects placed on
the appliance heat up very quickly and can cause
severe burns (this particularly applies to metal
objectssuchasknives,forks,spoons,
lids or cooktop extractor covers).
XX
Do not place any items on the appliance.
XX
Pleaseusesuitableaccessories(potholders,
oven gloves).
2.5.1 Safety instructions – cooktop
operation
ÿ
DANGER!
Danger of fire caused by leaving the cooktop
unattended
Oil or fat in the pot can quickly heat up and ignite.
XX
Never leave oil or fat to heat up unattended.
XX
Never extinguish oil and fat fires with water.
XX
Switch off the cooktop.
XX
Extinguish the fire using a pan lid or a fire
blanket,forexample.
ÿ
DANGER!
Danger of explosion caused by flammable
liquids
Flammable liquids in the vicinity of a cooktop can
explode and cause serious injury.
XX
Do not spray aerosols near the appliance when
it is in use.
XX
Do not place any flammable liquids in the
vicinity of a cooktop.
ÿ
WARNING!
Risk of burns from hot liquids boiling over
Unattended pans can boil over allowing hot liquids
to escape.
XX
Keep an eye on pans when cooking.
XX
Try not to let them boil over.
ÿ
WARNING!
Risk of burns from hot steam
Liquid between the cooking zone and the pan base
can evaporate and cause burns.
XX
Make sure that the cooking zone and the pan
base are always dry.
ÿ
WARNING!
Risk of burns due to power cut
Duringorafterapowercut,acooktopthatwas
previously in operation may still be hot even though
there is no indication of residual heat.
XX
Do not touch the cooktop while it is still hot.
XX
Keep children away from the hot cooktop.
CAUTION!
Damage caused by sugary and salty foods
Sugary and salty foods and juices can damage the
hot cooking zone.
XX
Make sure sugary and salty foods or juices do
not get onto the cooking zone while it is hot.
XX
Remove sugary and salty foods and juices from
the hot cooking zone immediately.
EN
9
Safety
www.bora.com
2.6 Safety instructions – cleaning
and maintenance
The appliance must be cleaned at regular intervals.
Dirt can lead to damage, restriction of functions, or
bothersome odours. In the worst case scenario, this
can become a hazard.
XX
Remove dirt immediately.
XX
When cleaning, only use non-abrasive detergents
to prevent scratching and abrasion on the surface.
XX
When cleaning, ensure that no water penetrates
the appliance. Use only a slightly damp cloth.
Never spray the device with water. Water
penetration can cause damage!
XX
Do not use a steam cleaner for cleaning. Steam
can cause a short circuit on live parts and thus
lead to property damage.
XX
Please follow all instructions in the “Cleaning and
Maintenance” chapter.
Special safety instructions for cooktop cleaning
and maintenance
XX
Whenever possible, clean the cooktops after every
use.
XX
Only clean the cooktops when they have cooled
down.
2.7 Safety instructions – repairs,
servicing and spare parts
i
The appliance must only be repaired and
serviced by trained specialists who are familiar
with and comply with the standard national
regulations and supplementary regulations of
the local utility companies.
i
Work on electrical components must only be
conducted by trained electrical personnel.
XX
Before any repair work, safely disconnect the
appliance from the mains supply.
ÿ
WARNING!
Risk of injury or damage from improper repairs
Incorrect components can lead to personal
injuryordamagetotheappliance.Modications,
additions or alterations to the appliance can lead to
safety risks.
XX
Only use original spare parts for repairs.
XX
Donotmakeanymodifications,additionsor
alterations to the appliance.
i
A damaged power supply cable must be
replaced by a suitable power supply cable. This
may only be done by an authorised member of
the After Sales Service team.
2.8 Safety instructions –
disassembly and disposal
i
The appliance must only be disassembled by
trained specialists who are familiar with and
comply with the standard national regulations
and supplementary regulations of the local
utility companies.
i
Work on electrical components must only be
conducted by trained electrical personnel.
XX
Before disassembly, safely disconnect the
appliance from the mains supply.
ÿ
DANGER!
Risk of electric shock from incorrect
disconnection
Incorrectly disconnecting the appliance from the
mains results in a risk of electric shock.
XX
Securely disconnect the appliance from the
mainsusingLSswitches,fuses,automatic
circuit breakers or contactors.
XX
Use an authorised measuring device to ensure
that there is no power to the appliance.
XX
Do not touch exposed contacts on the electronic
unit as they may contain residual charge.
EN
10
Technical data
www.bora.com
3 Technical data
240 65
341 14,5
73
43
7
Fig. 3.2 PKCH3 appliance dimensions front view
509 15,5
350
34,5
Fig. 3.3 PKCH3 appliance dimensions side view
3.2 BORA Professional 3.0 control
knob dimensions
Fig. 3.4 Control knob
Ø49
Ø58
Ø76
90
22 10-40 18
Fig. 3.5 Control knob dimensions
3.1 BORA Pro Hyper cooktop
1-ring/2-ring PKCH3
Parameter Value
Supply voltage 380–415V 2N
Frequency 50/60Hz
Power consumption 5.1kW
Fuse protection 2 x 16A
Dimensions (width x depth x height) 370 x 540 x 73mm
Weight (incl. accessories/packaging) 8.7kg
Cooktop
Power levels 1–9, Hyper level, 2-ring
additional switching
Heat retention levels 3
1-ring cooking zone
Hyper level
Ø 235mm 2100W
3200W
2-ring cooking zone Ø 120mm
Ø 200mm
800W
1900W
Energy consumption
(calculated with standard pot sizes)
Front cooking zone (240 mm) 175,9 Wh/kg
Rear cooking zone (210 mm) 189,1 Wh/kg
Total (average) 182,5 Wh/kg
Tab. 3.1 Technical data for PKCH3
PKCH3 appliance dimensions
370
540
Ø200
Ø235
255 133,5
R3
Fig. 3.1 PKCH3 appliance dimensions from above
EN
11
Appliance description
www.bora.com
4 Appliance description
Control knob display
3
1
2
4
Fig. 4.3 Control knob display elements
[1] Timer/egg timer indicator
[2] Rear cooking zone indicator
[3] Multi-function display
[4] Front cooking zone indicator
Control knob assignment
54321
Fig. 4.4 Control knob assignment
[1] Control knob for left cooktop, front cooking zone
[2] Control knob for left cooktop, rear cooking zone
[3] Control knob for cooktop extractor
[4] Control knob for right cooktop, front cooking zone
[5] Control knob for right cooktop, rear cooking zone
XX
Observe all safety and warning information during operation
(see the Safety chapter).
4.1 Control knob
How it works
The cooktop extractor and cooktops are operated with a control
knob. The power levels and functions are controlled by turning
the knob ring and pressing the touch surface.
i
How it works and its functions are described in more
detail in the Operation chapter.
Structure
4
3
5
2
1
Fig. 4.1 Control knob structure
[1] Knob housing
[2] Universal nut
[3] Control knob display
[4] Knob ring
[5] Wave spring
Operating elements
2
1
Fig. 4.2 Control knob operating elements
[1] Knob ring
[2] Touch surface
EN
12
Appliance description
www.bora.com
4.2.1 How the Hyper and HiLight cooktops
work (PKC3, PKCB3, PKCH3)
Under the cooking zone is a radiant heating element with a
heating tape. When the cooking zone is switched on, the heating
tape generates radiant heat, which radiates to the cooking zone
and heats it up.
Power levels
Activity Power level
Melting butter and chocolate, breaking up gelatine
1
Keeping sauces and soups warm, soaking rice
1
–
3
Cooking potatoes, pasta, soups and ragouts,
steaming fruit, vegetables and fish, defrosting food
2
–
6
Frying in coated pans, moderate frying (without
overheating the fat) of pork cutlets or fish
6
–
7
Heating up fat, browning fish, cooking thickened
sauces and soups, making omelettes
7
–
8
Cooking large amounts of liquids, grilling steaks
and heating water
9
Grilling steaks and heating up water
ßp
Tab. 4.2 Recommendations for power levels
The specifications provided in the table are standard values.
Depending on the cookware and filling quantity, it is
recommended to either decrease or increase the power level.
Power setting on cooktop PKCH3
The front cooking zone (Hyper zone) on the Hyper cooktop
PKCH3 is fitted with a temporary power setting.
XO
ßp
is shown in the control knob display.
The power setting can be used in order to quickly heat up large
quantities of water. If the power setting is activated, the cooking
zones will run at extra high power. After 10 minutes, the cooking
zone is automatically switched back to power level
9
.
Suitable cookware
i
Theheatingandheat-throughtimesforthecookware
base,aswellasthecookingresults,aresignificantly
influenced by the structure and material of the cookware.
Cookware with this symbol is suitable for radiant heating
elements. The cookware used for radiant heating
surfaces must be metal and have good heat conducting
properties.
Suitable cookware is made of:
XO
stainless steel, copper or aluminium
XO
enamelled steel
XO
cast iron
4.2 Cooktop appliance description
Display and symbols
i
The power levels and cooking functions of each cooking
zone are shown in the control knob display on the
corresponding control knob.
Control knob display
Indicator Meaning
0
Cooktop is switched off
1
–
9
Power levels
ßp
Power setting
H
Residual heat indicator
L
Childproofing feature
e.g.
5
,
/
5
:
/
5
*
Rings active
,
v
/
:
v
/
*
v
Heat retention levels active
Timer function active
A
Automatic heat up function
e.g.
A
5
Automatic heat up fun0ction active
E
...
Error message (see the Troubleshooting chapter)
Tab. 4.1 Control knob display
Layout and size of the cooking zones
1
2
200
235 120
Fig. 4.5 Layout of cooktop PKCH3 and cooking zone
dimensions
[1] 1-ring Hyper front cooking zone
[2] 2-ring rear cooking zone
EN
13
Appliance description
www.bora.com
Residual heat indicator
i
While
H
isdisplayed(residualheatindicator),donot
touchthecookingzoneorplaceanyheat-sensitive
objects on top of it. Risk of burns and fire!
After switching it off, the cooking zone remains hot.
H
is displayed (Residual heat indicator).
After a sufficient cooling period the indicator will go out
(Temperature < 60°C).
Overheating protection
i
Ifthecooktopoverheats,thepowerisreducedorthe
cooktop is switched off completely.
The appliance is fitted with overheating protection. The
overheating protection can be triggered if:
XO
cookware is heated up empty;
XO
oil or fat is heated on high power;
XO
a hot cooking zone is switched on again after a power cut.
Whilst the overheating protection is active, one of the following
steps is taken:
XO
the activated power setting is switched back to the previous
level;
XO
the power setting
ßp
can no longer be switched on;
XO
the set power level is reduced;
XO
the cooktop switches off completely.
After a sufficient cooling period, the cooktop can be used again.
Childproofing feature
i
If a single cooktop is operated without a cooktop
extractor,removaloftheknobringcanpreventthe
appliance from being switched on accidentally or without
permission.
XX
Pay attention to the cookware base. The bottom of the
cookware should not show any sign of curvature. Due to
incorrect hob temperature monitoring, this curvature may
cause the cookware to overheat. To avoid scratching the
cooktop, the base of the cookware must not have any sharp
grooves or sharp edges.
XX
Place the cookware (without a mat or similar) directly onto the
glass ceramic.
4.3 Safety devices
Safety shut-down
If an appliance is switched on but is not used for a predefined
time, it is automatically switched off.
Cooktops
Each cooking zone is switched off automatically when the cooking
zone exceeds the maximum operating duration on one power level
or heat retention level.
H
is displayed (Residual heat indicator).
PKCH3:
Power levels Safety shut-down after hours:minutes
1
6:00
2
6:00
3
5:00
4
5:00
5
4:00
6
1:30
7
1:30
8
1:30
9
1:30
ßp
0:10
Tab. 4.3 Safety shut-down on the different power levels
PKCH3:
Heat retention level Switch off after hours:minutes
1 (
,
v
)
8:00
2 (
:
v
)
8:00
3 (
*
v
)
8:00
Tab. 4.4 Safety shut-down on the different heat retention levels
XX
Switch the cooking zone back on if you want to put the
cooking zone back into operation (see the Operation chapter).
EN
14
Installation
www.bora.com
5 Installation
5.2 Checking the scope of delivery
XX
Make sure the delivery is complete and check it for damage.
XX
If there are any missing or damaged parts, please notify the
BORA After Sales Service.
XX
Do not under any circumstances install parts which are
damaged.
XX
Dispose of transport packaging in the proper manner (see the
“Decommissioning, disassembly and disposal” chapter).
Name Quantity
Cooktop 1
Control knob 2
Operating and installation instructions 1
Cooktop mounting screws 4
Height adjustment plate set 1
Cooktop mounting straps 4
Control knob cable 2
Automatic extraction system cable 1
Special scope of delivery for glass ceramic cooktops
Glass ceramic cleaning instructions 1
Tab. 5.1 Scope of delivery of the cooktops
5.3 Tools and aids
The following tools are required to correctly install the appliance:
XO
pencil
XO
tape measure or folding metre stick
XO
standard or cordless drill with Ø50mm Forstner bit
XO
black, heat-resistant silicone sealant
XO
slotted screwdriver
XO
size 20 Torx screwdriver
XX
Observe all safety and warning information (see the “Safety”
chapter).
XX
Follow the enclosed manufacturer’s information.
5.1 General installation instructions
i
The appliances must not be installed above cooling
devices,dishwashers,stoves,ovens,washingmachines
or dryers.
i
The contact surfaces of the worktops and wall sealing
stripsmustbemadeofaheat-resistantmaterial(upto
approx.100°C).
i
Worktopcut-outsmustbemoisture-sealedusingsuitable
meansand,wherenecessary,fittedwithathermal
insulator.
i
External devices may only be connected to the cooktop
extractor connections provided.
i
Extremely bright lights aimed directly at the appliances
can cause colour variations in the appliances and are
thus to be avoided.
General installation instructions for cooktops
i
To ensure that the cooktops perform optimally at all
times,theremustbesufficientventilationbeneaththe
cooktops.
i
The performance of the cooktops is affected or the
cooktops overheat if the warm air beneath the cooktops
cannot escape.
i
Ifacooktopoverheats,thepowerisautomatically
reduced or the cooktop is switched off completely (see
“Overheating protection”).
i
If cable protection (false floor) is planned beneath the
appliance,thismustbefittedsoitdoesnotobstruct
ventilation.
XX
Make sure that the area below the cooktop has a sufficient air
supply.
EN
15
Installation
www.bora.com
min.
700*
min.
74
176
900
(min.
890)
**
120
252
285
min.
100
170
682
max.
562
max.
430
389
*
110
PKA3
mit
Flachschalldämpfer
USDF,
Flachkanalverbinder
EFV
und
Übergangsstück
Versatz
EFRV110
(Zeile):
PKA3
mit
Rundschalldämpfer
USDR50
und
Rundkanal-
verbinder
ERV
(Insel):
PKAS3
mit
Ecotube
Flachkanal:
PKA3
mit
Flachschalldämpfer
USDF,
Flachkanalverbinder
EFV
und
Übergangsstück
gerade
EFRG
(Insel):
min.
700
min.
74
199
min.
100
120
691
min.
455
58
min.
328
max.
580
592
152
min.
810*
min.
74
176
900
(min.
890)
**
220
min.
100
110
760
max.
545
219* 151*
BORA
Professional
3.0
BO RA LÜFTU N GSFIBELXX
min.
810*
min.
74
176
900
(min.
890)
**
120
min.
100
93
min.
742
max.
562
219* 151*
295
33
180
Fig. 5.3 Appliance installation dimensions for standard set-up
of PKA3/PKA3AB with round silencer USDR50
5.4.3 Worktop and kitchen units
XX
Create the worktop cut-out taking into account the specified
cut-out dimensions.
XX
Make sure that the cut surfaces of the worktops are properly
sealed.
XX
Comply with the instructions of the worktop manufacturer.
XO
Cross bars on the kitchen unit in the area of the worktop cut-
out may need to be removed.
XO
No false floor is necessary below the cooktop. If cable
protection (false floor) is planned, the following must be taken
into account:
XO
it must be fitted in such a way that it can be removed for
maintenance work;
XO
to ensure sufficient cooktop ventilation, a minimum
distance of 15mm to the bottom edge of the cooktop is
to be observed.
XO
The drawers and/or shelves in the floor unit must be
removable.
XO
For correct installation, the drawers of the floor unit must be
shortened depending on the installation situation.
5.4 Assembly instructions
5.4.1 Safety clearances
XX
Maintain the following safety clearances:
1
3
2
Fig. 5.1 Minimum distance
[1] Minimum clearance of 50mm at the back from the worktop
cut-out to the rear edge of the worktop (in the case of
cooktops PKC3, PKCB3 and PKCH3 the minimum clearance is
70mm when the cooktop is installed rotated by 180°).
[2] Minimum clearance of 300mm from the left and right of the
worktop cut-out to the adjacent cabinet or wall.
[3] Minimum clearance of 600mm between the worktop and the
wall unit.
5.4.2 Minimum installation dimensions
(standard set-up)
≥810
≥890
≥900
Fig. 5.2 Minimum installation dimensions for standard set-up
of PKA3/PKA3AB
EN
16
Installation
www.bora.com
Cooktops/cooktop extractor A in mm B in mm
1/0 374 346
1/1 485 457
2/1 856 828
3/2 1338 1310
4/2 1709 1681
Tab. 5.2 Cut-out dimensions of the appliance combinations in
the case of ush installation
5.5.2 Surface mounting
x
B ±2
≤ R5
≥ 74
(≥ 70)
516 ±2
≥ 700
Fig. 5.7 Cut-out dimensions for surface mounting
12
10 - 40
Fig. 5.8 Overlay dimensions for surface mounting
5.5 Cut-out dimensions
i
All dimensions are shown from the front edge of the front
cover.
Worktop overhang
≥60
(
≥74
)
14x
Fig. 5.4 Worktop overhang
XX
Please note the worktop overhang x when creating the
worktop cut-out. Applies to flush installation and surface
mounting.
i
InthecaseofcooktopextractorPKA3/PKA3AB
combinedwithstraightductpiecePKA1FEV,flush
installation is also possible in a worktop with a depth
≥650mm.
5.5.1 Flush installation
x
A ±2
B ±2
544 ±2
≤ R5
≤ R5
≥ 74
(≥ 70)
516 ±2
≥ 700
Fig. 5.5 Cut-out dimensions for ush installation
7 +0,5
14
10 - 40
Fig. 5.6 Rebate dimensions for ush installation
EN
17
Installation
www.bora.com
5.6.2 Example bore holes
≥40≥70
90 90 90
Ø50 ±0,5
90 196 196
370 370
110
1 1
3
1 2
4 3 65
Fig. 5.11 Drilling pattern for 2 cooktops, 1 cooktop extractor
and 2 sockets
[1] Boreholes for socket (x 2 external)
[2] Bore holes for control knobs (x 5)
[3] Cooktop (x 2)
[4] Cooktop extractor
[5] Worktop
[6] Fixed front panel
≥70 ≥40
90 90 909090 196 196 196 196
370 370
370
110
1 1 1 1
110
Ø50 ±0,5
3
3
1 2 4 4 3 65
Fig. 5.12 Drilling pattern for 3 cooktops, 2 cooktop extractors
and 2 sockets
[1] Boreholes for socket (x 2 external)
[2] Bore holes for control knobs (x 8)
[3] Cooktop (x 3)
[4] Cooktop extractor (x 2)
[5] Worktop
[6] Fixed front panel
Cooktops/cooktop extractor B in mm
1/0 346
1/1 457
2/1 828
3/2 1310
4/2 1681
Tab. 5.3 Cut-out dimensions of the appliance combinations in
the case of surface mounting
5.6 Installing the control knob in the
floor unit front panel
Fig. 5.9 Installed control knob
XX
Pre-drill all bore holes to prevent tearing out the fixed front panel.
5.6.1 Cooktop bore holes
≥40≥70
Ø50 ±0,5
370
80-140
1 2 3
Fig. 5.10 Cooktop drilling pattern
[1] Cooktop
[2] Worktop
[3] Fixed front panel
EN
18
Installation
www.bora.com
XX
Tighten the universal nut [2].
XO
The wave spring (if used) must be pressed flat.
XX
Remove the sticker [3].
XX
Place the knob ring [4] on the knob housing [1].
5.7 Installing the cooktops
i
Clearance of one millimetre should be planned between
thebuilt-inappliances.
i
A clearance of two millimetres should be planned around
thebuilt-inappliances.
i
It is recommended to install a mounting rail between
adjacent cooktops (mounting rail PZMS available as an
accessory).
i
The cooktop can also be installed rotated by 180°.
5.7.1 Installing the cooktop
Inserting the cooktop (ports on the front)
321
Fig. 5.16 Inserting the cooktop
[1] Control knob and automatic extractor function ports (front)
[2] Cooktop
[3] Worktop cut-out
XX
Insert the cooktop [2] into the worktop cut-out [3].
XX
Align the cooktop [2] exactly.
XX
For a normal installation, please note that the ports for the
control knobs and the automatic extractor function [1] are at
the front.
i
The connection cables should be guided to the rear. Use
the cable holders provided.
5.6.3 Fitting the control knob
4
3
5
2
1
Fig. 5.13 Structure of control knob
[1] Knob housing
[2] Universal nut
[3] Sticker
[4] Knob ring
[5] Wave spring
i
Inthecaseofsteelfronts,wavespringsmustnotbeused.
The corresponding installation steps are to be omitted.
Fig. 5.14 Fitting the control knob
Fig. 5.15 Wave spring when installation is complete
XX
Remove the knob ring [4].
XX
Unscrew the universal nut [2].
XX
Remove the wave spring [5].
XX
Insert the knob housing [1] from the front through the hole in
the panel.
XX
Attach the wave spring [5] to the knob housing [1] from the
rear (not in the case of steel fronts).
XX
Screw the universal nut [2] onto the knob housing [1] from the
rear and tighten a little.
XX
Align the knob housing [1] so it is level.
EN
19
Installation
www.bora.com
5.7.2 Installation rotated by 180°
(alternative installation variation)
Special installation instructions for cooktops PKC3, PKCB3
and PKCH3 when installed rotated by 180°
1
3
2
Fig. 5.19 Minimum clearances for installation rotated by 180°
[1] Minimum clearance of 70mm at the back from the worktop
cut-out to the rear edge of the worktop.
[2] Minimum clearance of 300mm from the left and right of the
worktop cut-out to the adjacent cabinet or wall.
[3] Minimum clearance of 600mm between the worktop and the
wall unit.
Installation rotated by 180°
XX
Rotate the cooktop 180°.
XX
For the installation, proceed as described above.
XX
Change the installation direction in the configuration menu
(see “Configuration menu”).
i
Ifinstallationisrotatedby180°,theportsforthecontrol
knobs and the automatic extractor function are at the
rear.
i
Cables of sufficient length are provided.
Levelling the cooktop (if necessary)
1
2
Fig. 5.17 Cooktop and height adjustment plates
[1] Cooktop
[2] Height adjustment plates
XX
If applicable, insert the height adjustment plates [1].
Securing the cooktop
1
3
2
Fig. 5.18 Mounting brackets
[1] Mounting bracket
[2] Washer
[3] Screw
XX
Secure the appliance using the mounting brackets [1].
XX
Tighten the mounting brackets with the screw [3] using the
washer [2] with max. 2Nm.
XX
Verify that the alignment is correct.
EN
20
Installation
www.bora.com
Standard cooking zone connection
5 4
3
2
1
Fig. 5.22 Standard connection of appliances that connect at
the front
[1] Cooktop
[2] Rear cooking zone (zone 2)
[3] Front cooking zone (zone 1)
[4] Rear cooking zone control knob (zone 2)
[5] Front cooking zone control knob (zone 1)
Connecting the cooking zones when the cooktop is
installed rotated by 180°
5 4
3
2
1
Fig. 5.23 Connecting the cooking zones when the cooktop is
installed rotated by 180° and the ports are on the
front of the appliance
[1] Cooktop
[2] Rear cooking zone (zone 1)
[3] Front cooking zone (zone 2)
[4] Rear cooking zone control knob (zone 1)
[5] Front cooking zone control knob (zone 2)
5.8 Establishing communication and
power connection
XX
Observe all safety and warning information (see the “Safety”
chapter).
XO
The plug for the power supply must be accessible following
installation.
XO
If the power supply cable has been damaged this must be replaced.
i
The appliance components are linked by the ribbon cable
provided.
5.8.1 Connecting the control knobs
i
Control knobs must only be connected to the ports
provided on the appliance.
1
Fig. 5.20 Back of control knob with port
[1] Port on the back of the control knob
XX
Connect the control knobs to the appliances.
Connecting the control knobs to the cooktop
i
Inthenormalset-uptheportsareonthefrontofthecooktops.
i
Accordingtothedefaultsettings,theleftcontrolknob
operates the front cooking zone (zone 1) and the right
control knob operates the rear cooking zone (zone 2).
321
ZONE1 INTERF. COM1 ZONE2
Fig. 5.21 Ports on the cooktop
[1] Front cooking zone control knob port (zone 1)
[2] Extractor electronics interface port
[3] Rear cooking zone control knob port (zone 2)
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36

bora PKCH3 1xx User manual

bora
Brand
bora
Model
PKCH3 1xx
Category
Hobs
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents