bora PKCH3 1xx User manual

PKCH3UMIMEN-100

www.bora.com

Operating and installation instructions PKCH3

BORA Pro Hyper cooktop 1-ring/2-ring

1044094 - 36

www.bora.com

5.6.3 Fitting the control knob .......................................................18

5.7 Installing the cooktops .......................................................18

5.7.1 Installing the cooktop ..........................................................18

– Inserting the cooktop (ports on the front) ......................... 18

– Levelling the cooktop (if necessary) .................................. 19

– Securing the cooktop ........................................................ 19

5.7.2 Installation rotated by 180°

(alternative installation variation) ........................................19

5.8 Establishing communication and power connection ......20

5.8.1 Connecting the control knobs ............................................. 20

– Connecting the control knobs to the cooktop................... 20

5.8.2 Establishing contact between the

cooktop extractor and cooktops .........................................21

5.8.3 Connecting the power supply .............................................. 21

– Connecting the cooktop to the power supply ................... 21

5.9 Basic configuration ............................................................22

5.10 Initial operation ...................................................................22

5.11 Function test ........................................................................22

5.12 Sealing the appliances .......................................................22

5.13 Handover to user ................................................................22

6 Functions and operation 23

6.1 Knob operation .................................................................... 23

– Operating the knob ring .................................................... 23

– Operating the touch surface ............................................. 23

6.2 Switching the system on and off ......................................23

– Switching on ..................................................................... 23

– Switching off ..................................................................... 23

6.3 Operating the cooktops......................................................24

6.3.1 General operating instructions for cooktops ......................24

6.3.2 Setting cooking zone power levels ...................................... 24

– Increasing the power level ................................................. 24

– Reducing the power level .................................................. 24

6.3.3 Cooktop power setting ........................................................24

6.4 Function menu ....................................................................24

– Calling up the function menu ............................................ 24

6.4.1 Additionalringswitching–2-ring,3-ring,roaster ............... 25

– Activating additional rings

(2-ring/3-ring additional switching) ................................... 25

– Deactivating additional rings ............................................. 25

6.4.2 Variable heat retention function ..........................................25

– Activating the heat retention function ............................... 25

– Increasing or reducing the active heat retention level ....... 26

– Deactivating the heat retention function ........................... 26

6.4.3 Timerfunction/automaticcut-off .......................................26

– Activating cooking zone timers ......................................... 26

– Setting the time and starting the timer ............................. 26

– Changing active timers ...................................................... 27

– Switching the timer off early ............................................. 27

– Time lapsed ....................................................................... 27

6.4.4 Automatic heat up function .................................................27

– Activating the automatic heat up function......................... 27

– Deactivating the automatic heat up function early ............ 27

– Time lapsed ....................................................................... 27

1 General information 4

1.1 Liability ................................................................................... 4

1.2 Validity of the operating and installation instructions ...... 4

1.3 Product conformity ............................................................... 4

1.4 Data protection .....................................................................4

1.5 Presentation of information ................................................. 4

2 Safety 5

2.1 Use as intended ....................................................................5

2.2 People with limited abilities ................................................. 5

2.3 General safety instructions ..................................................5

2.4 Safety instructions for installation ...................................... 6

2.5 Safety instructions – operation ...........................................7

2.6 Safety instructions – cleaning and maintenance .............. 9

2.7 Safety instructions –

repairs, servicing and spare parts

... 9

2.8 Safety instructions – disassembly and disposal ...............9

3 Technical data 10

3.1 BORA Pro Hyper cooktop 1-ring/2-ring PKCH3 ..............10

3.2 BORA Professional 3.0 control knob dimensions............10

4 Appliance description 11

4.1 Control knob ........................................................................11

– How it works ..................................................................... 11

– Structure ........................................................................... 11

– Operating elements ........................................................... 11

– Control knob display ......................................................... 11

– Control knob assignment .................................................. 11

4.2 Cooktop appliance description ..........................................12

– Display and symbols.......................................................... 12

– Layout and size of the cooking zones ............................... 12

4.2.1 How the Hyper and HiLight cooktops work

(PKC3,PKCB3,PKCH3) ........................................................12

– Power levels ...................................................................... 12

– Suitable cookware ............................................................. 12

4.3 Safety devices .....................................................................13

– Safety shut-down .............................................................. 13

– Residual heat indicator ...................................................... 13

– Overheating protection ...................................................... 13

– Childproofing feature......................................................... 13

5 Installation 14

5.1 General installation instructions ......................................14

5.2 Checking the scope of delivery .........................................14

5.3 Tools and aids ...................................................................... 14

5.4 Assembly instructions ........................................................15

5.4.1 Safety clearances.................................................................15

5.4.2 Minimuminstallationdimensions(standardset-up) ........... 15

5.4.3 Worktop and kitchen units ..................................................15

5.5 Cut-out dimensions .............................................................16

5.5.1 Flush installation .................................................................. 16

5.5.2 Surface mounting ................................................................16

5.6

Installing the control knob in the floor unit front panel

...17

5.6.1 Cooktop bore holes .............................................................17

5.6.2 Example bore holes .............................................................17

Table of Contents

www.bora.com

7 Cleaning and maintenance 28

7.1 Cleaning agents ................................................................... 28

– Cleaning products for glass ceramic cooktops ................. 28

7.2 Cleaning the cooktops ........................................................ 28

7.2.1 Cleaning glass ceramic cooktops ........................................28

7.3 Looking after your cooktops .............................................. 28

7.4 Cleaning the control knobs ................................................ 29

– Cleaning the knob ring ...................................................... 29

– Cleaning the touch surface and the knob housing ............ 29

8 Troubleshooting 30

9 Decommissioning, disassembly and

disposal 31

9.1 Decommissioning ...............................................................31

9.2 Disassembly ........................................................................31

9.3 Environmentally-friendly disposal .....................................31

10 Warranty, technical service,

spare parts, accessories 32

10.1 BORA manufacturer’s warranty .........................................32

10.2 Service .................................................................................32

10.3 Spare parts ..........................................................................32

10.4 Accessories .......................................................................... 32

11 Notes 33

General information

www.bora.com

1 General information

1.5 Presentation of information

We use standard formatting, numbering, symbols, safety

instructions, terms and abbreviations so that you can work

quickly and safely when using this manual.

The term “appliance” is used to refer to cooktops, cooktop

extractors or cooktops with integrated cooktop extractor.

Instructions are indicated with an arrow.

Always follow all instructions in the prescribed order.

Enumerations are indicated with a bullet point at the start of

the line:

Enumeration 1

Enumeration 2

Information notes point to special features that must be

taken into account.

Safety and warning instructions

The safety and warning instructions in this manual are

emphasised with symbols and signal words.

Safety and warning instructions are structured as follows:

WARNING SYMBOL AND SIGNAL WORD!

Type and source of danger

Resultsofnon-compliance

Measures to minimise risk

Please note:

warning symbols draw attention to a high risk of injury.

The signal word indicates the severity of that risk.

Warning

symbol

Signal word Risk

Danger Indicates an immediate, hazardous

situation which causes death or

serious injury if not respected.

Warning Indicates a potentially hazardous

situation which can cause death or

serious injury if not respected.

Caution Indicates a potentially hazardous

situation which can cause minor

injury or damage to property if not

respected.

Tab. 1.1 Meaning of the warning symbols and signal words

These instructions contain important information to protect you

from injury and prevent damage to the appliance.

Please read these instructions carefully before installing or using

the appliance for the first time.

Other documents apply alongside these instructions.

Please by all means adhere to all documents that form part of

the scope of delivery.

Assembly and installation may only be carried out by trained

specialists and taking into account the applicable laws,

regulations and standards. All safety and warning information

as well as the handling instructions in the accompanying

documents must be observed.

1.1 Liability

BORA Holding GmbH, BORA Vertriebs GmbH & Co KG, BORA

APAC Pty Ltd and BORA Lüftungstechnik GmbH – hereinafter

referred to as BORA – does not assume any liability for damage

arising from disregard for or non-adherence to the documents

included in the scope of delivery!

Furthermore, BORA shall not be held liable for damage caused

by improper installation or failure to observe the safety and

warning instructions!

1.2 Validity of the operating and

installation instructions

These instructions apply to several appliance versions. It is

therefore possible that some of the features described do not

apply to your appliance. The details of the figures contained

herein may differ from some appliance versions and are to be

understood as schematic diagrams.

1.3 Product conformity

Directives

The appliances meet the following EU/EC directives:

2014/30/EU EMC Directive

2014/35/EU Low Voltage Directive

2009/125/EC Ecodesign Directive

2011/65/EU RoHS Directive

1.4 Data protection

During operation your cooktop extractor saves pseudonymised

data such as menu settings entered by you, operating hours

of the individual technical units and the number of functions

selected. Furthermore, your cooktop extractor documents errors

in combination with the number of operating hours.

Data can only be read out manually via your cooktop extractor.

This decision is therefore your responsibility.

These saved data then enable a rapid error search and

troubleshooting in the event of servicing.

Safety

www.bora.com

2 Safety

People with reduced physical, sensory or

mental capacities

The appliance can be used by people with reduced

physical, sensory or mental capacities or a lack of

experience and/or knowledge if they are supervised

or have been instructed how to use the appliance

safely and understand the resultant risks. Operation

can be restricted using the childproofing feature.

DANGER!

Risk of burns from hot cookware and food

Handles projecting over the edge of the worktop

are asking to be grabbed.

Keep children away from hot cooking zones or

ensure they are supervised at all times.

Do not turn pot and pan handles so they stick

out beyond the worktop.

Make sure that hot pots and pans cannot be

pulled down.

Ifnecessary,usesuitablestoveguardsor

covers.

Only use stove guards and covers that are

approved by the appliance manufacturer;

otherwise,thereisariskofaccidents.

Tochooseasuitablestoveguard,contactyour

specialistsupplierortheBORAServiceTeam.

2.3 General safety instructions

DANGER!

Packaging components are a choking hazard

Packagingcomponents(e.g.lm,polystyrene)can

belife-threateningforchildren.

Store all packaging components out of reach of

children.

Dispose of the packaging properly and

immediately.

The appliance complies with the stipulated safety

requirements. The user is responsible for the safe

use of the appliance, cleaning and maintenance.

Improper use can lead to personal injury and damage

to property.

2.1 Use as intended

The appliance is solely intended for preparing food in

private households.

This appliance is not intended for:

outdoor use

heating rooms

cooling, ventilating or dehumidifying rooms

use in mobile installation sites such as motor

vehicles, ships or aeroplanes

use with an external timer or a separate remote

control system (except for emergency shutdown)

use at altitudes of over 2,000 m (metres above sea

level).

Any other use or any use that goes beyond that which

is described here is classed as unintended.

BORAdoesnotassumeanyliabilityfor

damages caused by improper use or incorrect

operation.

All misuse is prohibited!

2.2 People with limited abilities

Children

The appliance can be used by children aged 8 and

over if they are supervised or have been instructed

how to use the appliance safely and understand

the resultant risks. Children must not play with the

appliance.

Use the childproofing feature in order to prevent

children from switching on the appliance or

changing the settings when they are unattended.

Supervise children in the vicinity of the appliance.

Do not store any items that could be of interest to

children in storage spaces above or behind the

appliance. Otherwise, they will be tempted to

climb onto the appliance.

Any work involving cleaning and maintenance

must not be carried out by children unless they

are supervised at all times while doing so.

Safety

www.bora.com

CAUTION!

Risk of injury from heavy lifting

Ifnothandledcorrectly,carryingandinstalling

appliances can cause injury to the limbs or torso.

Ifnecessary,carryandinstalltheappliancewith

another person.

Use appropriate aids to prevent damage or

injury.

CAUTION!

Damage from improper use

The appliance surfaces must not be used as

work or storage surfaces. This can damage the

appliances (particularly in the case of hard and

sharp objects).

Never use the appliances as work or storage

surfaces.

Keep hard or sharp objects away from the

appliance surfaces.

Faults and errors

In the case of faults and errors, follow the

instructions in the “Troubleshooting” chapter.

In the event of any faults or errors that are not

mentioned, switch the appliance off and contact

BORA Service.

Pets

Keep pets away from the appliance.

2.4 Safety instructions for

installation

The appliance must only be installed and

assembled by trained specialists who are

familiar with and comply with the standard

national regulations and supplementary

regulations of the local utility companies.

During installation maintain the minimum

clearance stated in the “Installation” (“Safety

clearances”) chapter.

Work on electrical components must only be

conducted by trained electrical personnel.

The electrical safety of the appliance is only

guaranteed if it is connected to a protective

conductor system that has been installed in line with

regulations. Ensure that this basic safety precaution

is met.

DANGER!

Risk of electric shock or injury from damaged

surfaces

The underlying electronics can be exposed or

damagedduetossures,fracturesorcracksin

appliancesurfaces(e.g.damagedglassceramic),

particularly in the operating area. This can cause

anelectricshock.Furthermore,adamagedsurface

can cause injuries.

Do not touch the damaged surface.

Ifthereareanycracks,fissuresorfractures,

switch the appliance off immediately.

Safely disconnect the appliance from the mains

usingtheLSswitch,fuses,automaticcircuit

breakers or contactor.

ContactBORAService.

WARNING!

Risk of injury from damaged components

Damaged components that cannot be removed

without tools can cause injuries.

Try not to repair or replace damaged

components yourself.

ContactBORAService.

WARNING!

Risk of injury or damage due to incorrect

components or unauthorised modifications

Incorrect components can lead to personal

injuryordamagetotheappliance.Modications,

additions or alterations to the appliance can lead to

safety risks.

Only use original components.

Donotmakeanymodifications,additionsor

alterations to the appliance.

CAUTION!

Appliance components can cause injury if

dropped

Appliancecomponents(e.g.pansupports,

operatingcontrols,covers,greaselters,etc.)can

cause injury if dropped.

Place any appliance components that have been

removed in a safe place near the appliances.

Ensure that no components removed from the

appliances can fall on the floor.

Safety

www.bora.com

The appliance must be suitable for the regional

voltage and frequency.

Check the information on the identification plate

and in the event of deviations, do not connect the

appliance.

Conduct all work extremely attentively and

conscientiously.

Do not connect the appliance to the mains until

the duct system has been installed or the

recirculation filter has been fitted.

Only use the connection cables supplied. Where

necessary these are included in the scope of

delivery.

Do not use the appliance until installation is

complete. This is the only way to ensure safe

operation.

DANGER!

Risk of electric shock from damaged appliance

A damaged appliance can cause an electric shock.

Check the appliance for visible damage prior to

installation.

Do not install or connect any damaged

appliances.

Do not operate any damaged appliances.

CAUTION!

Risk of burning from control knobs that are

not positioned optimally.

If the control knobs are not installed in a suitable

place,duringoperationthereisariskofsustaining

burns from the cooktop surface.

Onlyinstallthecontrolknobsinasuitableplace,

which is practical and safe.

2.4.1 Safety instructions for cooktop

installation

DANGER!

Risk of electric shock from incorrect mains

connection

Connecting the appliance to the mains incorrectly

poses a risk of electric shock.

Make sure that the appliance has a fixed

connection to the mains voltage.

Make sure that the appliance is connected to a

properly installed protective conductor system.

Make sure that technical equipment is provided

to enable all of the appliance’s poles to be

disconnected from the mains with a contact

opening width of at least 3 mm (LS switch and

automaticcircuitbreakers,fuses,contactor).

DANGER!

Risk of electric shock from damaged power

supply cable

If the power supply cable is damaged (e.g. during

installation or by coming into contact with hot

cookingsurfaces),thiscancausean(lethal)

electric shock.

Make sure that the power supply cable does not

become trapped or damaged.

Make sure that the power supply cable does not

come into contact with hot cooking surfaces.

2.5 Safety instructions – operation

Make sure that the base of the cookware as well

as the appliance surfaces are clean and dry.

Always lift (do not drag) cookware to prevent

scratching and abrasion on the appliance surface.

Do not use the appliance as a storage surface.

Switch off the appliance after use.

Safety

www.bora.com

WARNING!

Risk of burning from hot appliances

Certain appliances and their exposed parts become

hot during use (e.g. cooktops). They should be

left to cool down completely after switching off.

Touching hot surfaces can cause serious burns.

Do not touch hot appliances.

Pay attention to the residual heat indicator.

WARNING!

Risk of burning and fire from hot objects

The appliance and its exposed parts are hot during

operation and the cooling phase. Objects placed on

the appliance heat up very quickly and can cause

severe burns (this particularly applies to metal

objectssuchasknives,forks,spoons,

lids or cooktop extractor covers).

Do not place any items on the appliance.

Pleaseusesuitableaccessories(potholders,

oven gloves).

2.5.1 Safety instructions – cooktop

operation

DANGER!

Danger of fire caused by leaving the cooktop

unattended

Oil or fat in the pot can quickly heat up and ignite.

Never leave oil or fat to heat up unattended.

Never extinguish oil and fat fires with water.

Switch off the cooktop.

Extinguish the fire using a pan lid or a fire

blanket,forexample.

DANGER!

Danger of explosion caused by flammable

liquids

Flammable liquids in the vicinity of a cooktop can

explode and cause serious injury.

Do not spray aerosols near the appliance when

it is in use.

Do not place any flammable liquids in the

vicinity of a cooktop.

WARNING!

Risk of burns from hot liquids boiling over

Unattended pans can boil over allowing hot liquids

to escape.

Keep an eye on pans when cooking.

Try not to let them boil over.

WARNING!

Risk of burns from hot steam

Liquid between the cooking zone and the pan base

can evaporate and cause burns.

Make sure that the cooking zone and the pan

base are always dry.

WARNING!

Risk of burns due to power cut

Duringorafterapowercut,acooktopthatwas

previously in operation may still be hot even though

there is no indication of residual heat.

Do not touch the cooktop while it is still hot.

Keep children away from the hot cooktop.

CAUTION!

Damage caused by sugary and salty foods

Sugary and salty foods and juices can damage the

hot cooking zone.

Make sure sugary and salty foods or juices do

not get onto the cooking zone while it is hot.

Remove sugary and salty foods and juices from

the hot cooking zone immediately.

Safety

www.bora.com

2.6 Safety instructions – cleaning

and maintenance

The appliance must be cleaned at regular intervals.

Dirt can lead to damage, restriction of functions, or

bothersome odours. In the worst case scenario, this

can become a hazard.

Remove dirt immediately.

When cleaning, only use non-abrasive detergents

to prevent scratching and abrasion on the surface.

When cleaning, ensure that no water penetrates

the appliance. Use only a slightly damp cloth.

Never spray the device with water. Water

penetration can cause damage!

Do not use a steam cleaner for cleaning. Steam

can cause a short circuit on live parts and thus

lead to property damage.

Please follow all instructions in the “Cleaning and

Maintenance” chapter.

Special safety instructions for cooktop cleaning

and maintenance

Whenever possible, clean the cooktops after every

use.

Only clean the cooktops when they have cooled

down.

2.7 Safety instructions – repairs,

servicing and spare parts

The appliance must only be repaired and

serviced by trained specialists who are familiar

with and comply with the standard national

regulations and supplementary regulations of

the local utility companies.

Work on electrical components must only be

conducted by trained electrical personnel.

Before any repair work, safely disconnect the

appliance from the mains supply.

WARNING!

Risk of injury or damage from improper repairs

Incorrect components can lead to personal

injuryordamagetotheappliance.Modications,

additions or alterations to the appliance can lead to

safety risks.

Only use original spare parts for repairs.

Donotmakeanymodifications,additionsor

alterations to the appliance.

A damaged power supply cable must be

replaced by a suitable power supply cable. This

may only be done by an authorised member of

the After Sales Service team.

2.8 Safety instructions –

disassembly and disposal

The appliance must only be disassembled by

trained specialists who are familiar with and

comply with the standard national regulations

and supplementary regulations of the local

utility companies.

Work on electrical components must only be

conducted by trained electrical personnel.

Before disassembly, safely disconnect the

appliance from the mains supply.

DANGER!

Risk of electric shock from incorrect

disconnection

Incorrectly disconnecting the appliance from the

mains results in a risk of electric shock.

Securely disconnect the appliance from the

mainsusingLSswitches,fuses,automatic

circuit breakers or contactors.

Use an authorised measuring device to ensure

that there is no power to the appliance.

Do not touch exposed contacts on the electronic

unit as they may contain residual charge.

Technical data

www.bora.com

3 Technical data

240 65

341 14,5

Fig. 3.2 PKCH3 appliance dimensions front view

509 15,5

350

34,5

Fig. 3.3 PKCH3 appliance dimensions side view

3.2 BORA Professional 3.0 control

knob dimensions

Fig. 3.4 Control knob

Ø49

Ø58

Ø76

22 10-40 18

Fig. 3.5 Control knob dimensions

3.1 BORA Pro Hyper cooktop

1-ring/2-ring PKCH3

Parameter Value

Supply voltage 380–415V 2N

Frequency 50/60Hz

Power consumption 5.1kW

Fuse protection 2 x 16A

Dimensions (width x depth x height) 370 x 540 x 73mm

Weight (incl. accessories/packaging) 8.7kg

Cooktop

Power levels 1–9, Hyper level, 2-ring

additional switching

Heat retention levels 3

1-ring cooking zone

Hyper level

Ø 235mm 2100W

3200W

2-ring cooking zone Ø 120mm

Ø 200mm

800W

1900W

Energy consumption

(calculated with standard pot sizes)

Front cooking zone (240 mm) 175,9 Wh/kg

Rear cooking zone (210 mm) 189,1 Wh/kg

Total (average) 182,5 Wh/kg

Tab. 3.1 Technical data for PKCH3

PKCH3 appliance dimensions

370

540

Ø200

Ø235

255 133,5

Fig. 3.1 PKCH3 appliance dimensions from above

Appliance description

www.bora.com

4 Appliance description

Control knob display

Fig. 4.3 Control knob display elements

[1] Timer/egg timer indicator

[2] Rear cooking zone indicator

[3] Multi-function display

[4] Front cooking zone indicator

Control knob assignment

54321

Fig. 4.4 Control knob assignment

[1] Control knob for left cooktop, front cooking zone

[2] Control knob for left cooktop, rear cooking zone

[3] Control knob for cooktop extractor

[4] Control knob for right cooktop, front cooking zone

[5] Control knob for right cooktop, rear cooking zone

Observe all safety and warning information during operation

(see the Safety chapter).

4.1 Control knob

How it works

The cooktop extractor and cooktops are operated with a control

knob. The power levels and functions are controlled by turning

the knob ring and pressing the touch surface.

How it works and its functions are described in more

detail in the Operation chapter.

Structure

Fig. 4.1 Control knob structure

[1] Knob housing

[2] Universal nut

[3] Control knob display

[4] Knob ring

[5] Wave spring

Operating elements

Fig. 4.2 Control knob operating elements

[1] Knob ring

[2] Touch surface

Appliance description

www.bora.com

4.2.1 How the Hyper and HiLight cooktops

work (PKC3, PKCB3, PKCH3)

Under the cooking zone is a radiant heating element with a

heating tape. When the cooking zone is switched on, the heating

tape generates radiant heat, which radiates to the cooking zone

and heats it up.

Power levels

Activity Power level

Melting butter and chocolate, breaking up gelatine

Keeping sauces and soups warm, soaking rice

–

Cooking potatoes, pasta, soups and ragouts,

steaming fruit, vegetables and fish, defrosting food

–

Frying in coated pans, moderate frying (without

overheating the fat) of pork cutlets or fish

–

Heating up fat, browning fish, cooking thickened

sauces and soups, making omelettes

–

Cooking large amounts of liquids, grilling steaks

and heating water

Grilling steaks and heating up water

ßp

Tab. 4.2 Recommendations for power levels

The specifications provided in the table are standard values.

Depending on the cookware and filling quantity, it is

recommended to either decrease or increase the power level.

Power setting on cooktop PKCH3

The front cooking zone (Hyper zone) on the Hyper cooktop

PKCH3 is fitted with a temporary power setting.

ßp

is shown in the control knob display.

The power setting can be used in order to quickly heat up large

quantities of water. If the power setting is activated, the cooking

zones will run at extra high power. After 10 minutes, the cooking

zone is automatically switched back to power level

Suitable cookware

Theheatingandheat-throughtimesforthecookware

base,aswellasthecookingresults,aresignificantly

influenced by the structure and material of the cookware.

Cookware with this symbol is suitable for radiant heating

elements. The cookware used for radiant heating

surfaces must be metal and have good heat conducting

properties.

Suitable cookware is made of:

stainless steel, copper or aluminium

enamelled steel

cast iron

4.2 Cooktop appliance description

Display and symbols

The power levels and cooking functions of each cooking

zone are shown in the control knob display on the

corresponding control knob.

Control knob display

Indicator Meaning

Cooktop is switched off

–

Power levels

ßp

Power setting

Residual heat indicator

Childproofing feature

e.g.

Rings active

Heat retention levels active

Timer function active

Automatic heat up function

e.g.

Automatic heat up fun0ction active

...

Error message (see the Troubleshooting chapter)

Tab. 4.1 Control knob display

Layout and size of the cooking zones

200

235 120

Fig. 4.5 Layout of cooktop PKCH3 and cooking zone

dimensions

[1] 1-ring Hyper front cooking zone

[2] 2-ring rear cooking zone

Appliance description

www.bora.com

Residual heat indicator

While

isdisplayed(residualheatindicator),donot

touchthecookingzoneorplaceanyheat-sensitive

objects on top of it. Risk of burns and fire!

After switching it off, the cooking zone remains hot.

is displayed (Residual heat indicator).

After a sufficient cooling period the indicator will go out

(Temperature < 60°C).

Overheating protection

Ifthecooktopoverheats,thepowerisreducedorthe

cooktop is switched off completely.

The appliance is fitted with overheating protection. The

overheating protection can be triggered if:

cookware is heated up empty;

oil or fat is heated on high power;

a hot cooking zone is switched on again after a power cut.

Whilst the overheating protection is active, one of the following

steps is taken:

the activated power setting is switched back to the previous

level;

the power setting

ßp

can no longer be switched on;

the set power level is reduced;

the cooktop switches off completely.

After a sufficient cooling period, the cooktop can be used again.

Childproofing feature

If a single cooktop is operated without a cooktop

extractor,removaloftheknobringcanpreventthe

appliance from being switched on accidentally or without

permission.

Pay attention to the cookware base. The bottom of the

cookware should not show any sign of curvature. Due to

incorrect hob temperature monitoring, this curvature may

cause the cookware to overheat. To avoid scratching the

cooktop, the base of the cookware must not have any sharp

grooves or sharp edges.

Place the cookware (without a mat or similar) directly onto the

glass ceramic.

4.3 Safety devices

Safety shut-down

If an appliance is switched on but is not used for a predefined

time, it is automatically switched off.

Cooktops

Each cooking zone is switched off automatically when the cooking

zone exceeds the maximum operating duration on one power level

or heat retention level.

is displayed (Residual heat indicator).

PKCH3:

Power levels Safety shut-down after hours:minutes

6:00

5:00

4:00

1:30

ßp

0:10

Tab. 4.3 Safety shut-down on the different power levels

PKCH3:

Heat retention level Switch off after hours:minutes

1 (

)

8:00

2 (

)

8:00

3 (

)

8:00

Tab. 4.4 Safety shut-down on the different heat retention levels

Switch the cooking zone back on if you want to put the

cooking zone back into operation (see the Operation chapter).

Installation

www.bora.com

5 Installation

5.2 Checking the scope of delivery

Make sure the delivery is complete and check it for damage.

If there are any missing or damaged parts, please notify the

BORA After Sales Service.

Do not under any circumstances install parts which are

damaged.

Dispose of transport packaging in the proper manner (see the

“Decommissioning, disassembly and disposal” chapter).

Name Quantity

Cooktop 1

Control knob 2

Operating and installation instructions 1

Cooktop mounting screws 4

Height adjustment plate set 1

Cooktop mounting straps 4

Control knob cable 2

Automatic extraction system cable 1

Special scope of delivery for glass ceramic cooktops

Glass ceramic cleaning instructions 1

Tab. 5.1 Scope of delivery of the cooktops

5.3 Tools and aids

The following tools are required to correctly install the appliance:

pencil

tape measure or folding metre stick

standard or cordless drill with Ø50mm Forstner bit

black, heat-resistant silicone sealant

slotted screwdriver

size 20 Torx screwdriver

Observe all safety and warning information (see the “Safety”

chapter).

Follow the enclosed manufacturer’s information.

5.1 General installation instructions

The appliances must not be installed above cooling

devices,dishwashers,stoves,ovens,washingmachines

or dryers.

The contact surfaces of the worktops and wall sealing

stripsmustbemadeofaheat-resistantmaterial(upto

approx.100°C).

Worktopcut-outsmustbemoisture-sealedusingsuitable

meansand,wherenecessary,fittedwithathermal

insulator.

External devices may only be connected to the cooktop

extractor connections provided.

Extremely bright lights aimed directly at the appliances

can cause colour variations in the appliances and are

thus to be avoided.

General installation instructions for cooktops

To ensure that the cooktops perform optimally at all

times,theremustbesufficientventilationbeneaththe

cooktops.

The performance of the cooktops is affected or the

cooktops overheat if the warm air beneath the cooktops

cannot escape.

Ifacooktopoverheats,thepowerisautomatically

reduced or the cooktop is switched off completely (see

“Overheating protection”).

If cable protection (false floor) is planned beneath the

appliance,thismustbefittedsoitdoesnotobstruct

ventilation.

Make sure that the area below the cooktop has a sufficient air

supply.

Installation

www.bora.com

min.

700*

min.

176

900

(min.

890)

120

252

285

min.

100

170

682

max.

562

max.

430

389

110

PKA3

mit

Flachschalldämpfer

USDF,

Flachkanalverbinder

EFV

und

Übergangsstück

Versatz

EFRV110

(Zeile):

PKA3

mit

Rundschalldämpfer

USDR50

und

Rundkanal-

verbinder

ERV

(Insel):

PKAS3

mit

Ecotube

Flachkanal:

PKA3

mit

Flachschalldämpfer

USDF,

Flachkanalverbinder

EFV

und

Übergangsstück

gerade

EFRG

(Insel):

min.

700

min.

199

min.

100

120

691

min.

455

min.

328

max.

580

592

152

min.

810*

min.

176

900

(min.

890)

220

min.

100

110

760

max.

545

219* 151*

BORA

Professional

3.0

BO RA LÜFTU N GSFIBELXX

min.

810*

min.

176

900

(min.

890)

120

min.

100

min.

742

max.

562

219* 151*

295

180

810

Fig. 5.3 Appliance installation dimensions for standard set-up

of PKA3/PKA3AB with round silencer USDR50

5.4.3 Worktop and kitchen units

Create the worktop cut-out taking into account the specified

cut-out dimensions.

Make sure that the cut surfaces of the worktops are properly

sealed.

Comply with the instructions of the worktop manufacturer.

Cross bars on the kitchen unit in the area of the worktop cut-

out may need to be removed.

No false floor is necessary below the cooktop. If cable

protection (false floor) is planned, the following must be taken

into account:

it must be fitted in such a way that it can be removed for

maintenance work;

to ensure sufficient cooktop ventilation, a minimum

distance of 15mm to the bottom edge of the cooktop is

to be observed.

The drawers and/or shelves in the floor unit must be

removable.

For correct installation, the drawers of the floor unit must be

shortened depending on the installation situation.

5.4 Assembly instructions

5.4.1 Safety clearances

Maintain the following safety clearances:

Fig. 5.1 Minimum distance

[1] Minimum clearance of 50mm at the back from the worktop

cut-out to the rear edge of the worktop (in the case of

cooktops PKC3, PKCB3 and PKCH3 the minimum clearance is

70mm when the cooktop is installed rotated by 180°).

[2] Minimum clearance of 300mm from the left and right of the

worktop cut-out to the adjacent cabinet or wall.

[3] Minimum clearance of 600mm between the worktop and the

wall unit.

5.4.2 Minimum installation dimensions

(standard set-up)

≥810

≥890

≥900

Fig. 5.2 Minimum installation dimensions for standard set-up

of PKA3/PKA3AB

Installation

www.bora.com

Cooktops/cooktop extractor A in mm B in mm

1/0 374 346

1/1 485 457

2/1 856 828

3/2 1338 1310

4/2 1709 1681

Tab. 5.2 Cut-out dimensions of the appliance combinations in

the case of ush installation

5.5.2 Surface mounting

B ±2

≤ R5

≥ 74

(≥ 70)

516 ±2

≥ 700

Fig. 5.7 Cut-out dimensions for surface mounting

10 - 40

Fig. 5.8 Overlay dimensions for surface mounting

5.5 Cut-out dimensions

All dimensions are shown from the front edge of the front

cover.

Worktop overhang

≥60

(

≥74

)

14x

Fig. 5.4 Worktop overhang

Please note the worktop overhang x when creating the

worktop cut-out. Applies to flush installation and surface

mounting.

InthecaseofcooktopextractorPKA3/PKA3AB

combinedwithstraightductpiecePKA1FEV,flush

installation is also possible in a worktop with a depth

≥650mm.

5.5.1 Flush installation

A ±2

B ±2

544 ±2

≤ R5

≥ 74

(≥ 70)

516 ±2

≥ 700

Fig. 5.5 Cut-out dimensions for ush installation

7 +0,5

10 - 40

Fig. 5.6 Rebate dimensions for ush installation

Installation

www.bora.com

5.6.2 Example bore holes

≥40≥70

90 90 90

Ø50 ±0,5

90 196 196

370 370

110

1 1

1 2

4 3 65

Fig. 5.11 Drilling pattern for 2 cooktops, 1 cooktop extractor

and 2 sockets

[1] Boreholes for socket (x 2 external)

[2] Bore holes for control knobs (x 5)

[3] Cooktop (x 2)

[4] Cooktop extractor

[5] Worktop

[6] Fixed front panel

≥70 ≥40

90 90 909090 196 196 196 196

370 370

370

110

1 1 1 1

110

Ø50 ±0,5

1 2 4 4 3 65

Fig. 5.12 Drilling pattern for 3 cooktops, 2 cooktop extractors

and 2 sockets

[1] Boreholes for socket (x 2 external)

[2] Bore holes for control knobs (x 8)

[3] Cooktop (x 3)

[4] Cooktop extractor (x 2)

[5] Worktop

[6] Fixed front panel

Cooktops/cooktop extractor B in mm

1/0 346

1/1 457

2/1 828

3/2 1310

4/2 1681

Tab. 5.3 Cut-out dimensions of the appliance combinations in

the case of surface mounting

5.6 Installing the control knob in the

floor unit front panel

Fig. 5.9 Installed control knob

Pre-drill all bore holes to prevent tearing out the fixed front panel.

5.6.1 Cooktop bore holes

≥40≥70

Ø50 ±0,5

370

80-140

1 2 3

Fig. 5.10 Cooktop drilling pattern

[1] Cooktop

[2] Worktop

[3] Fixed front panel

Installation

www.bora.com

Tighten the universal nut [2].

The wave spring (if used) must be pressed flat.

Remove the sticker [3].

Place the knob ring [4] on the knob housing [1].

5.7 Installing the cooktops

Clearance of one millimetre should be planned between

thebuilt-inappliances.

A clearance of two millimetres should be planned around

thebuilt-inappliances.

It is recommended to install a mounting rail between

adjacent cooktops (mounting rail PZMS available as an

accessory).

The cooktop can also be installed rotated by 180°.

5.7.1 Installing the cooktop

Inserting the cooktop (ports on the front)

321

Fig. 5.16 Inserting the cooktop

[1] Control knob and automatic extractor function ports (front)

[2] Cooktop

[3] Worktop cut-out

Insert the cooktop [2] into the worktop cut-out [3].

Align the cooktop [2] exactly.

For a normal installation, please note that the ports for the

control knobs and the automatic extractor function [1] are at

the front.

The connection cables should be guided to the rear. Use

the cable holders provided.

5.6.3 Fitting the control knob

Fig. 5.13 Structure of control knob

[1] Knob housing

[2] Universal nut

[3] Sticker

[4] Knob ring

[5] Wave spring

Inthecaseofsteelfronts,wavespringsmustnotbeused.

The corresponding installation steps are to be omitted.

Fig. 5.14 Fitting the control knob

Fig. 5.15 Wave spring when installation is complete

Remove the knob ring [4].

Unscrew the universal nut [2].

Remove the wave spring [5].

Insert the knob housing [1] from the front through the hole in

the panel.

Attach the wave spring [5] to the knob housing [1] from the

rear (not in the case of steel fronts).

Screw the universal nut [2] onto the knob housing [1] from the

rear and tighten a little.

Align the knob housing [1] so it is level.

Installation

www.bora.com

5.7.2 Installation rotated by 180°

(alternative installation variation)

Special installation instructions for cooktops PKC3, PKCB3

and PKCH3 when installed rotated by 180°

Fig. 5.19 Minimum clearances for installation rotated by 180°

[1] Minimum clearance of 70mm at the back from the worktop

cut-out to the rear edge of the worktop.

[2] Minimum clearance of 300mm from the left and right of the

worktop cut-out to the adjacent cabinet or wall.

[3] Minimum clearance of 600mm between the worktop and the

wall unit.

Installation rotated by 180°

Rotate the cooktop 180°.

For the installation, proceed as described above.

Change the installation direction in the configuration menu

(see “Configuration menu”).

Ifinstallationisrotatedby180°,theportsforthecontrol

knobs and the automatic extractor function are at the

rear.

Cables of sufficient length are provided.

Levelling the cooktop (if necessary)

Fig. 5.17 Cooktop and height adjustment plates

[1] Cooktop

[2] Height adjustment plates

If applicable, insert the height adjustment plates [1].

Securing the cooktop

Fig. 5.18 Mounting brackets

[1] Mounting bracket

[2] Washer

[3] Screw

Secure the appliance using the mounting brackets [1].

Tighten the mounting brackets with the screw [3] using the

washer [2] with max. 2Nm.

Verify that the alignment is correct.

Installation

www.bora.com

Standard cooking zone connection

5 4

Fig. 5.22 Standard connection of appliances that connect at

the front

[1] Cooktop

[2] Rear cooking zone (zone 2)

[3] Front cooking zone (zone 1)

[4] Rear cooking zone control knob (zone 2)

[5] Front cooking zone control knob (zone 1)

Connecting the cooking zones when the cooktop is

installed rotated by 180°

5 4

Fig. 5.23 Connecting the cooking zones when the cooktop is

installed rotated by 180° and the ports are on the

front of the appliance

[1] Cooktop

[2] Rear cooking zone (zone 1)

[3] Front cooking zone (zone 2)

[4] Rear cooking zone control knob (zone 1)

[5] Front cooking zone control knob (zone 2)

5.8 Establishing communication and

power connection

Observe all safety and warning information (see the “Safety”

chapter).

The plug for the power supply must be accessible following

installation.

If the power supply cable has been damaged this must be replaced.

The appliance components are linked by the ribbon cable

provided.

5.8.1 Connecting the control knobs

Control knobs must only be connected to the ports

provided on the appliance.

Fig. 5.20 Back of control knob with port

[1] Port on the back of the control knob

Connect the control knobs to the appliances.

Connecting the control knobs to the cooktop

Inthenormalset-uptheportsareonthefrontofthecooktops.

Accordingtothedefaultsettings,theleftcontrolknob

operates the front cooking zone (zone 1) and the right

control knob operates the rear cooking zone (zone 2).

321

ZONE1 INTERF. COM1 ZONE2

Fig. 5.21 Ports on the cooktop

[1] Front cooking zone control knob port (zone 1)

[2] Extractor electronics interface port

[3] Rear cooking zone control knob port (zone 2)

Page is loading ...

bora PKCH3 1xx User manual

Related papers

Other documents