IKEA HYGIENISK Owner's manual

HYGIENISK

GB

DE

ENGLISH

Please refer to the last page of this manual for the full list of IKEA

appointed After Sales Service Provider and relative national phone

numbers.

DEUTSCH

Auf der letzten Seite dieser Broschüre finden Sie eine vollständige

Liste der offiziellen IKEA After-Sales-Dienstleister mit den

jeweiligen nationalen Telefonnummern.

ENGLISH 4

DEUTSCH 30

Contents

Safety information 4

Safety instructions 5

Product description 7

Control panel 8

Programmes 9

Options 11

Settings 12

Before first use 16

Daily use 17

Hints and tips 19

Care and cleaning 21

Troubleshooting 23

Technical information 27

ENVIRONMENTAL CONCERNS 27

IKEA GUARANTEE 27

Subject to change without notice.

Safety information

Before the installation and use of the appliance, carefully read

the supplied instructions. The manufacturer is not responsible

for any injuries or damages that are the result of incorrect

installation or usage. Always keep the instructions in a safe and

accessible location for future reference.

Children and vulnerable people safety

• This appliance can be used by children aged from 8 years

and above and persons with reduced physical, sensory or

mental capabilities or lack of experience and knowledge if

they have been given supervision or instruction concerning

the use of the appliance in a safe way and understand the

hazards involved.

• Do not let children play with the appliance.

• Keep detergents away from children.

• Keep children and pets away from the appliance when the

door is open.

• Children shall not carry out cleaning and user maintenance of

the appliance without supervision.

ENGLISH

4

General Safety

• This appliance is intended to be used in household and

similar applications such as:

– farm houses; staff kitchen areas in shops, offices and other

working environments;

– by clients in hotels, motels, bed & breakfast and other

residential type environments.

• Do not change the specification of this appliance.

• The operating water pressure (minimum and maximum) must

be between 0.5 (0.05) / 8 (0.8) bar (MPa)

• Obey the maximum number of 15 place settings.

• If the supply cord is damaged, it must be replaced by the

manufacturer, its Authorised Service Centre or similarly

qualified persons in order to avoid a hazard.

• Put the cutlery in the cutlery basket with the sharp ends

pointing down or put them in the cutlery drawer in a

horizontal position with the sharp edges down.

• Do not leave the appliance with the open door unattended to

avoid stepping accidentally onto it.

• Before any maintenance operation, deactivate the appliance

and disconnect the mains plug from the socket.

• Do not use high pressure water sprays and/or steam to clean

the appliance.

• If the appliance has ventilation openings in the base, they

must not be covered e.g. by a carpet.

• The appliance is to be connected to the water mains using

the new supplied hose-sets. Old hose sets must not be

reused.

Safety instructions

Installation

• Remove all the packaging.

• Do not install or use a damaged

appliance.

• Do not install or use the appliance where

the temperature is less than 0 °C.

• Follow the installation instruction

supplied with the appliance.

ENGLISH 5

• Make sure that the appliance is installed

below and adjacent to safe structures.

Electrical connection

Warning! Risk of fire and

electrical shock.

• The appliance must be earthed.

• Make sure that the parameters on the

rating plate are compatible with the

electrical ratings of the mains power

supply.

• Always use a correctly installed

shockproof socket.

• Do not use multi-plug adapters and

extension cables.

• Make sure not to cause damage to the

mains plug and to the mains cable.

Should the mains cable need to be

replaced, this must be carried out by our

Authorised Service Centre.

• Connect the mains plug to the mains

socket only at the end of the installation.

Make sure that there is access to the

mains plug after the installation.

• Do not pull the mains cable to disconnect

the appliance. Always pull the mains

plug.

• This appliance complies with the E.E.C.

Directives.

• Only for UK and Ireland. The appliance

has a 13 amp mains plug. If it is

necessary to change the fuse in the

mains plug, use fuse: 13 amp ASTA (BS

1362).

Water connection

• Do not cause damage to the water

hoses.

• Before connection to new pipes, pipes

not used for a long time, where repair

work has been carried out or new

devices fitted (water meters, etc.), let the

water flow until it is clean and clear.

• Ensure that there are no visible water

leaks during and after the first use of the

appliance.

• The water inlet hose has a safety valve

and a sheath with an inner mains cable.

Warning! Dangerous voltage.

• If the water inlet hose is damaged,

immediately close the water tap and

disconnect the mains plug from the mains

socket. Contact the Authorised Service

Centre to replace the water inlet hose.

Use

• Do not sit or stand on the open door.

• Dishwasher detergents are dangerous.

Obey the safety instructions on the

detergent packaging.

• Do not drink and play with the water in

the appliance.

• Do not remove the dishes from the

appliance until the programme is

complete. Some detergent may remain

on the dishes.

• The appliance can release hot steam if

you open the door while a programme

operates.

• Do not put flammable products or items

that are wet with flammable products in,

near or on the appliance.

Internal light

Warning! Risk of injury.

• This appliance has an internal lamp that

comes on when you open the door and

goes off when the door is closed.

• The lamp in this appliance is not suitable

for household room illumination.

• To replace the lamp, contact the Service.

ENGLISH

6

Service

• Contact the Authorised Service Centre to

repair the appliance. We recommend

only the use of original spare parts.

• When you contact the Authorised Service

Centre, ensure that you have the

following information that is available on

the rating plate.

Model :

PNC :

Serial Number :

Disposal

Warning! Risk of injury or

suffocation.

• Disconnect the appliance from the mains

supply.

• Cut off the mains cable and discard it.

• Remove the door catch to prevent

children and pets to get closed in the

appliance.

Product description

5

4

10

9

67

11

12

2

3

1

8

1

Top spray arm

2

Upper spray arm

3

Lower spray arm

4

Filters

5

Rating plate

6

Salt container

7

Air vent

8

Rinse aid dispenser

9

Detergent dispenser

10

Lower basket

11

Upper basket

12

Cutlery drawer

ENGLISH 7

TimeBeam

The TimeBeam is a display that is shown on

the floor below the appliance door.

• When the programme starts, the

programme duration comes on.

• When the programme is completed,

0:00 and CLEAN come on.

• When the delay start starts, the

countdown duration and DELAY come

on.

• When the appliance has a malfunction,

an alarm code appears.

When AutoOpen is activated

during the drying phase, the

projection on the floor may not

be completely visible. To check

the remaining time of the running

programme, look at the control

panel display.

Control panel

1

2 3 4 5 6 7 8 9

1

On/off button

2

Display

3

Delay button

4

Programme button (up)

5

Programme button (down)

6

ExtraHygiene button

7

DryPlus button

8

RESET button

9

Indicators

ENGLISH 8

Indicators

Indicator Description

End indicator.

Rinse aid indicator. It is always off while the programme operates.

Salt indicator. It is always off while the programme operates.

Programmes

Programme Degree of soil

Type of load

Programme phases Options

P1

1)

• All

• Crockery, cutlery,

pots and pans

• Prewash

• Wash from 45 °C to 70

°C

• Rinse

• Dry

• ExtraHygiene

• DryPlus

P2

• Heavy soil

• Crockery, cutlery,

pots and pans

• Prewash

• Wash 70 °C

• Rinse

• Dry

• ExtraHygiene

• DryPlus

P3

2)

• Fresh soil

• Crockery and

cutlery

• Wash 60 °C

• Rinse

• ExtraHygiene

• DryPlus

P4

3)

• Normal soil

• Crockery and

cutlery

• Prewash

• Wash 50 °C

• Rinse

• Dry

• ExtraHygiene

• DryPlus

P5

• Light soil

• Delicate crockery

and glassware

• Wash 45 °C

• Rinses

• Dry

• DryPlus

P6

4)

• All • Prewash

ENGLISH 9

Programme Degree of soil

Type of load

Programme phases Options

P7

5)

• Normal soil

• Crockery and

cutlery

• Prewash

• Wash 50 °C

• Rinse

• Dry

• DryPlus

1)

The appliance senses the degree of soil and the quantity of items in the baskets . It automatically adjusts the tem-

perature and the quantity of water, the energy consumption and the programme duration.

2)

With this programme you can wash a load with fresh soil. It gives good washing results in a short time.

3)

With this programme you have the most efficient use of water and energy consumption for crockery and cutlery with

normal soil. (This is the standard programme for test institutes).

4)

With this programme you can quickly rinse dishes to prevent remains of food to bond on dishes and odours to form

in the appliance. Do not use detergent with this programme.

5)

This is the most silent programme. The pump works at a very low speed to decrease the level of noise. Because of

the low speed, the programme duration is long.

Consumption values

Programme

1)

Water

(l)

Energy

(kWh)

Duration

(min)

P1 7 - 14 0.6 - 1.6 40 - 170

P2 12.5-14.5 1.4-1.7 170-190

P3 10 0.9 41

P4 11 0.86 232

P5 12 - 14 0.7 - 0.9 82-92

P6 4 0.1 14

P7 9 - 10 1.1 - 1.3 230 - 250

1)

The pressure and the temperature of the water, the variations of the mains supply, the options and the quantity of

dishes can change the values.

ENGLISH 10

Information for test institutes

For all the necessary information for test

performance, send an email to:

[email protected]

Write down the product number (PNC) that

is on the rating plate.

Options

Desired options must be

activated every time before you

start a programme.

It is not possible to activate or

deactivate options while a

programme is running.

Not all options are compatible

with each other. If you have

selected non compatible options,

the appliance will automatically

deactivate one or more of them.

Only the indicators of the options

still active will stay on.

DryPlus

Activate this option when you want to boost

the drying performance. With use of this

option, the duration of some programmes,

water consumption and the last rinse

temperature can be affected.

The combination of DryPlus and rinse aid

gives you even better drying result.

The DryPlus option is a permanent option

for all programmes other than P4 (ECO)

and need not to be selected at every cycle.

Every time P4 (ECO) is activated, DryPlus

option is off and needs to be chosen

manually. In other programmes, the setting

of DryPlus is permanent and is

automatically used in the next cycles. The

setting can be changed at any time before

programme starts.

How to activate DryPlus

Press .

The related indicator comes on.

If the option is not applicable to the

programme, the related indicator does not

come on or it flashes quickly for a few

seconds and then goes off.

The display shows the updated programme

duration.

ExtraHygiene

This option provides better hygiene results

by keeping the temperature at 70 °C for at

least 10 minutes during last rinsing phase.

How to activate ExtraHygiene

Press , the related indicator comes on.

If the option is not applicable to the

selected programme, the indicator stays off.

The display shows the updated programme

duration.

The ExtraHygiene option is not applicable

to the following programmes:

• P5 (Glass)

• P6 (Rinse & Hold)

• P7 (Extra Silent)

AutoOpen is deactivated when

the programme P3 (Quick) is

combined with ExtraHygiene

option due to the high

temperature.

ENGLISH 11

Settings

Programme selection mode and user

mode

When the appliance is in programme

selection mode it is possible to set a

programme and to enter the user mode.

In user mode, the following settings can

be changed:

• The level of the water softener according

to the water hardness.

• The activation or the deactivation of the

acoustic signal for end of programme.

• The selection of the colour for TimeBeam.

• The activation or deactivation of the

rinse aid empty notification.

• The level of rinse aid according to the

required dosage.

• The activation or the deactivation of

AutoOpen.

These settings will be saved until you

change them again.

How to set the programme selection mode

The appliance is in programme selection

mode when the display shows the

programme number P4.

When you activate the appliance, usually it

is in programme selection mode. However,

if this does not happen, you can set the

programme selection mode in the following

way:

Press and hold RESET until the appliance is

in programme selection mode.

The water softener

The water softener removes minerals from

the water supply, which would have a

detrimental effect on the washing results

and on the appliance.

The higher the content of these minerals, the

harder your water is. Water hardness is

measured in equivalent scales.

The water softener should be adjusted

according to the hardness of the water in

your area. Your local water authority can

advise you on the hardness of the water in

your area. It is important to set the right

level of the water softener to assure good

washing results.

Water hardness

German degrees

(°dH)

French degrees

(°fH)

mmol/l Clarke de-

grees

Water softener level

47 - 50 84 - 90 8.4 - 9.0 58 - 63 10

43 - 46 76 - 83 7.6 - 8.3 53 - 57 9

37 - 42 65 - 75 6.5 - 7.5 46 - 52 8

29 - 36 51 - 64 5.1 - 6.4 36 - 45 7

23 - 28 40 - 50 4.0 - 5.0 28 - 35 6

19 - 22 33 - 39 3.3 - 3.9 23 - 27

5

1)

15 - 18 26 - 32 2.6 - 3.2 18 - 22 4

ENGLISH 12

German degrees

(°dH)

French degrees

(°fH)

mmol/l Clarke de-

grees

Water softener level

11 - 14 19 - 25 1.9 - 2.5 13 - 17 3

4 - 10 7 - 18 0.7 - 1.8 5 - 12 2

<4 <7 <0.7 < 5

1

2)

1)

Factory setting.

2)

Do not use salt at this level.

Whether you use a standard detergent or

multi-tabs (with or without salt), set the

proper water hardness level to keep the

salt refill indicator active.

Multi-tabs containing salt are not

effective enough to soften hard

water.

How to set the water softener level

The appliance must be in programme

selection mode.

1. To enter the user mode, press and hold

simultaneously and until

the indicators , , , ,

and flash and the display is

blank.

2. Press

.

• The indicators , , ,

and are off.

• The indicator still flashes.

• The display shows the current setting:

e.g. = level 5.

3. Press

repeatedly to change the

setting.

4. Press the on/off button to confirm the

setting.

The rinse aid dispenser

The rinse aid helps to dry the dishes without

streaks and stains.

The rinse aid is automatically released

during the hot rinse phase.

You can set the released quantity of rinse

aid between level 1 (minimum quantity) and

level 6 (maximum quantity). Level 0 will

deactivate the rinse aid dispenser and no

rinse aid will be released.

Factory setting: level 4.

How to set the rinse aid level

The appliance must be in programme

selection mode.

1. To enter the user mode, press and hold

simultaneously

and until

the indicators , , , ,

and start flashing and the

display is blank.

2. Press .

• The indicators , , , and

are off.

• The indicator continues to

flash.

• The display shows the current setting:

e.g. = level 4.

– The levels of rinse aid range from

0A to 6A where level 0A means

rinse aid is not used.

3. Press repeatedly to change the

setting.

4. Press on/off to confirm the setting.

ENGLISH

13

The rinse aid empty notification

The rinse aid helps to dry the dishes without

streaks and stains.

The rinse aid is automatically released

during the hot rinse phase.

When rinse aid chamber is empty, the rinse

aid indicator is turned on notifying to refill

rinse aid. If you are using multi-tabs

containing rinse aid and you are satisfied

with the drying result, you can deactivate

the notification for refilling rinse aid.

However, we recommend that you always

use rinse aid for best drying performance.

If you use standard detergent or multi-

tablets without rinse aid, activate the

notification to keep the rinse aid refill

indicator active.

How to deactivate the rinse aid empty

notification

The appliance must be in programme

selection mode.

1. To enter the user mode, press and hold

simultaneously

and until

the indicators , , , ,

and start flashing and the

display is blank.

2. Press

.

• The indicators , , , and

are off.

• The indicator still flashes.

• The display shows the current setting:

= the rinse aid empty notification

is activated (factory setting).

3. Press to change the setting.

= the rinse aid empty notification is

deactivated.

4. Press on/off to confirm the setting.

Acoustic signals

Acoustic signals sound when a malfunction

of the appliance occurs. It is not possible to

deactivate these acoustic signals.

There is also an acoustic signal that sounds

when the programme is completed. By

default, this acoustic signal is activated and

it is possible to deactivate it.

In addition, an acoustic signal will sound

before the AutoOpen will open the door.

This acoustic signal stops only if AutoOpen

is deactivated.

How to deactivate the acoustic signal for

the end of programme

The appliance must be in programme

selection mode.

1. To enter the user mode press and hold

simultaneously and until

the indicators , , , ,

and start to flash and the

display is blank.

2. Press

• The indicators , , ,

and go off.

• The indicator continues to flash.

• The display shows the current setting:

= Acoustic signal on.

3. Press to change the setting.

= Acoustic signal off.

4. Press the on/off button to confirm the

setting.

How to set the colour of the TimeBeam

It is possible to change the colour of the

TimeBeam to match the colour of the

kitchen floor. There are several colours

available. The TimeBeam can also be

deactivated.

ENGLISH

14

The appliance must be in programme

selection mode.

1. To enter the user mode, press and hold

simultaneously and until

the indicators

, , , ,

and flash and the display is

blank.

2. Press .

• The indicators , , ,

and are off.

• The indicator still flashes.

• The display shows a number and

letter C. Each number refers to a

different colour.

– = TimeBeam deactivated.

3. Press repeatedly to change the

colour.

4. Press on/off to confirm the setting.

AutoOpen

AutoOpen improves the drying results with

less energy consumption.

While the drying phase operates,

a device opens the appliance

door. The door is then kept ajar.

Caution! Do not try to close the

appliance door within 2 minutes

after automatic opening. This can

cause damage to the appliance.

To avoid possible hazards inside

the appliance (such as knives,

sharp objects or chemicals) for

children, pets or people with

disabilities, deactivate the

function.

AutoOpen is automatically activated with

all programmes excluding

.

AutoOpen is deactivated when

the programme P3 (Quick) is

combined with ExtraHygiene

option due to the high

temperature.

To improve the drying performance refer to

the DryPlus option or activate AutoOpen.

How to deactivate AutoOpen

The appliance must be in programme

selection mode.

1. To enter the user mode, press and hold

simultaneously

and until

the indicators

, , , ,

and start flashing and the

display is blank.

2. Press .

• The indicators , , ,

and are off.

• The indicator still flashes.

• The display shows the current setting:

= AutoOpen activated.

3. Press to change the setting:

= AutoOpen deactivated.

4. Press on/off to confirm the setting.

ENGLISH

15

Before first use

1. Make sure that the current level of the

water softener agrees with the

hardness of the water supply. If not,

adjust the level of the water softener.

2. Fill the salt container.

3. Fill the rinse aid dispenser.

4. Open the water tap.

5. Start a programme to remove any

processing residuals that can still be

inside the appliance. Do not use

detergent and do not load the baskets.

When you start a programme,

the appliance can take up to 5

minutes to recharge the resin in

the water softener. It seems that

the appliance is not working. The

washing phase starts only after

this procedure is completed. The

procedure will be repeated

periodically.

The salt container

Caution! Only use salt

specifically designed for

dishwashers.

The salt is used to recharge the resin in the

water softener and to assure good washing

results in the daily use.

Filling the salt container

1 2

3

Put 1 litre of water

in the salt container

(only for the first

time).

4

Put 1 kg of salt in

the salt container.

5

Caution! Water and salt can

come out from the salt container

when you fill it. Risk of corrosion.

To prevent this, after the

replenishment, start a

programme.

Filling the rinse aid dispenser

1 2

ENGLISH 16

3

A

Fill the rinse aid

dispenser until the

rinse aid reaches

the marking "MAX".

Remove the spilled

rinse aid with an

absorbent cloth to

prevent too much

foam.

Fill the rinse aid

dispenser when the

indicator (A)

becomes clear and

the rinse aid

indicator on the

control panel is on.

4

Daily use

1. Open the water tap.

2. Press the on/off button to activate the

appliance.

Make sure that the appliance is in

programme selection mode.

• If the salt indicator is on, fill the salt

container.

• If the rinse aid indicator is on, fill the

rinse aid dispenser.

3. Load the baskets.

4. Add the detergent.

5. Set and start the correct programme for

the type of load and the degree of soil.

Using the detergent

1 2

2

1

ENGLISH 17

3

30

4

5

If the programme

has a prewash

phase, put a small

quantity of

detergent on the

inner part of the

appliance door.

Setting and starting a programme

The Auto Off function

This function decreases energy consumption

by automatically deactivating the

appliance when it is not operating.

The function comes into operation:

• 5 minutes after the completion of the

programme.

• After 5 minutes if the programme has not

started.

Starting a programme

Caution! Do not remove the

baskets from the dishwasher

before a wash cycle.

1. Keep the appliance door ajar.

2. Press the on/off button to activate the

appliance. Make sure that the

appliance is in programme selection

mode.

3. Press or repeatedly until

the display shows the number of the

programme you want to start. The

display will show the programme

number for approximately 3 seconds

and next the programme duration.

4. Set the applicable options.

5. Close the appliance door to start the

programme.

Starting a programme with delay start

1. Set a programme.

2. Press

repeatedly until the display

shows the delay time you want to set

(from 1 to 24 hours).

The delay indicator comes on.

3. Close the appliance door to start the

countdown.

While a countdown is running it is possible

to increase the delay time but not to change

the selection of the programme and

options.

When the countdown is completed, the

programme starts.

Opening the door while the appliance

operates

If you open the door while a programme is

running, the appliance stops. It may affect

the energy consumption and the

programme duration. When you close the

door, the appliance continues from the

point of interruption.

ENGLISH

18

If the door is opened for more

than 30 seconds during the

drying phase, the running

programme will end. This will not

happen if the door is opened by

AutoOpen.

Caution! Do not try to close the

appliance door within 2 minutes

after AutoOpen automatically

opens it, as this may cause

damage to the appliance. If,

afterwards, the door is closed for

another 3 minutes, the running

programme ends.

Cancelling the delay start while the

countdown operates

When you cancel the delay start you have

to set the programme and options again.

Press and hold RESET until the appliance is

in programme selection mode.

Cancelling the programme

Press and hold RESET until the appliance is

in programme selection mode.

Make sure that there is detergent in the

detergent dispenser before you start a new

programme.

End of programme

When the programme is completed and

you open the door, the appliance is

automatically deactivated.

Close the water tap.

Hints and tips

General

The following hints will ensure optimal

cleaning and drying results in daily use and

also help to protect the environment.

• Remove larger residues of food from the

dishes into the waste bin.

• Do not pre-rinse dishes by hand. When

needed, use the prewash programme (if

available) or select a programme with a

prewash phase.

• Always use the whole space of the

baskets.

• When loading the appliance, make sure

that the dishes can be completely

reached and washed by the water

released from the spray arm nozzles.

Make sure that items do not touch or

cover each other.

• You can use dishwasher detergent, rinse

aid and salt separately or you can use

the multi-tablets (e.g. ''3in1'', ''4in1'', ''All

in 1''). Follow the instructions written on

the packaging.

• Select the programme according to the

type of load and degree of soil. With the

ECO programme you have the most

efficient use of water and energy

consumption for crockery and cutlery

with normal soil.

Using salt, rinse aid and detergent

• Only use salt, rinse aid and detergent for

dishwasher. Other products can cause

damage to the appliance.

• In areas with hard and very hard water

we recommend to use plain dishwasher

detergent (powder, gel, tablets

containing no additional agents), rinse

aid and salt separately for optimal

cleaning and drying results.

• At least once a month run the appliance

with the use of appliance cleaner which

is particularly suitable for this purpose.

ENGLISH 19

• Detergent tablets do not fully dissolve

with short programmes. To prevent

detergent residues on the tableware, we

recommend that you use the tablets with

long programmes.

• Do not use more than the correct

quantity of detergent. Refer to the

instructions on the detergent packaging.

What to do if you want to stop using multi-

tablets

Before you start to use separately

detergent, salt and rinse aid do the

following procedure.

1. Set the highest level of the water

softener.

2. Make sure that the salt and rinse aid

containers are full.

3. Start the shortest programme with a

rinsing phase. Do not add detergent

and do not load the baskets.

4. When the programme is completed,

adjust the water softener according to

the water hardness in your area.

5. Adjust the released quantity of rinse aid.

6. Activate the rinse aid empty notification.

Loading the baskets

Refer to the supplied leaflet with

examples of the load of the

baskets.

• Only use the appliance to wash items

that are dishwasher-safe.

• Do not put in the appliance items made

of wood, horn, aluminium, pewter and

copper.

• Do not put in the appliance items that

can absorb water (sponges, household

cloths).

• Remove remaining food from the items.

• Soak items with remaining burned food

in water.

• Put hollow items (cups, glasses and pans)

with the opening down.

• Make sure that cutlery and dishes do not

bond together. Mix spoons with other

cutlery.

• Make sure that glasses do not touch

each other.

• Put small items in the cutlery drawer .

• Put light items in the upper basket. Make

sure that the items do not move.

• Make sure that the spray arm can move

freely before you start a programme.

Before starting a programme

Make sure that:

• The filters are clean and correctly

installed.

• The cap of the salt container is tight.

• The spray arms are not clogged.

• There is dishwasher salt and rinse aid

(unless you use multi- tablets).

• The position of the items in the baskets is

correct.

• The programme is applicable for the

type of load and for the degree of soil.

• The correct quantity of detergent is used.

Unloading the baskets

For better drying results keep the

appliance door ajar for some

minutes before you remove the

dishes.

1. Let the dishes cool down before you

remove them from the appliance. Hot

dishes are easily damaged.

2. First remove items from the lower basket

then the upper basket.

At the end of the program water

can still remain on the sides and

on the door of the appliance.

ENGLISH 20

Page is loading ...

IKEA HYGIENISK Owner's manual

This manual is also suitable for

IKEA HYGIENISK Owner's manual

in other languages

Related papers

Other documents