USER MANUAL
Bluetooth Headset PAROS-10
CONTENTS
1. Charging a headset..........................................................................2
2. Package contents ............................................................................2
3. Pair to your bluetooth phone ............................................................3
4. Operation .........................................................................................4
5. Wearing your headset......................................................................4
6. Volume control & mute function .......................................................5
7. Making a call....................................................................................5
8. Ending a call ....................................................................................5
9. Reject an incoming call ....................................................................5
10. Answering a call...............................................................................5
11. Transferring a call ............................................................................6
12. Call waiting (3-way calling)...............................................................6
13. Summary of button operation...........................................................6
14. Troubleshooting ...............................................................................7
15. Additional Information ......................................................................8
16. Safety ..............................................................................................8
Page 2
English - PAROS-10
1. Charging a headset
* Make sure that your headset is fully
charged before you start using it. When
your headset is charged, the red LED is
on.
* When the battery needs to be recharged,
you will hear warning beep tones every 20
seconds and the red LED will blink also.
2. Lieferumfang
1. Bluetooth Headset
2. Ear hook (2)
3. A/C power adaptor
4. Car Charger (optional)
5. Spare Ear-Cushion
6. User manual
7. Warranty Card
8. Supplement “Important Information””
1.
Speaker
Multi-function Button
Mic
Status
LED
Charging Port
Volume
Controll
Button
2. 3. 4. 5.
6. 7. 8.
Page 3
PAROS-10 - English
3. Pair to your bluetooth phone
Before you use your headset for the first time, you should pair your headset with the device that you want to use with, such as your
Bluetooth phone.
(Fig.Pairing)
Important: When the headset is paired with mobile phone, the
LED
will flash two times every 5 seconds. If failed, the blue
LED
will flash one time ever
y
5 seconds
!
Ensure the
headset is off.
Press and hold the Multi-Function
Button until you see the LED
blinking blue and red
(approx. 6 seconds), then release.
Set your Bluetooth phone to
“discover” the headset by following
your phone´s instruction. Typically,
“Bluetooth” menu on you phone and
then selecting the option to
“discover” a Bluetooth device.
Our phone will find
your headset and ask
if you want to pair
with it. Confirm this
by pressing “yes” or
“ok”.
Enter passkey or
PIN = 0000 (4 zeros),
then press “yes” or
“ok”.
*Auto connection
Once you pair the headset
with a device, the headset will
be automatically connected to
the device whenever you turn
the headset on.
Page 4
English - PAROS-10
4. Operation
How to act Tones Indicators
Turning headset on
Press and hold the MFB for 5
seconds until you see the LED
flashing blue, then release it
Turn-On melody
The blue LED or will flash
while the power is on
Turning off headset
Press and hold the MFB for 4
seconds until you see the LED
flashing red, then release it
Turn-Off melody
After red LED indicator flash, it
will be turned off
5. Wearing your headset:
Right Ear
Take off
and flip to wear
at left
Left ea
r
wearing
position
Page 5
PAROS-10 - English
6. Volume Control & mute Function
• You can adjust the volume by pressing volume up and volume down button.
• Press and hold the volume down button for 2 seconds, then the headset microphone will be muted. To deactivate the mute function,
press and hold the volume down button for 2 seconds.
7. Making a call
USING PHONE’S KEYPAD
• Dial number on keypad./ - Press phone’s “send/call” key/ - If your phone does not automatically transfer the call to the headset, press
MFB for 2 seconds.
USING VOICE DIAL
• Please make sure that your mobile phone supports the voice dial function. If so, please set up voice tags on your mobile phone first.
• Press the MFB for 2 seconds until you hear short beep. After then release the button
• Say the name of person you want to call
• A melody in the headset will confirm that the call is made
LAST NUMBER RE-DIAL
• Press the MFB briefly and the last number called will be re-dialed.
• A melody in the headset will confirm that the call is made
8. Ending a call
• Press the MFB briefly to end an active call. You can also end your call from your mobile phone.
9. Reject an incoming call
• Press and hold the MFB for 2 seconds and release button when you hear a beep tone.
10. Answering a call
• Press the MFB briefly to answer an incoming call.
Please record voice tag thru your headset for better recognition
!
Page 6
English - PAROS-10
11. Transferring a call
You can transfer a call from the headset to your mobile phone without interrupting the connection:
• Headset to phone: Press MFB for 2 seconds
• Phone to headset: Press MFB for 2 seconds
12. Call waiting (3-way calling)
To use “3-way-calling” with your headset your mobile phone must support the “Handsfree Profile” (please refer to its manual) and your
network/carrier must offer “call hold and/or multiparty” services.
• Press and hold the volume-down button for approximately 4 seconds until you hear 3 short beep tones, then you can answer the
receiving waiting (incoming) call and end the active call.
• Press and hold volume-up button until you hear short beep 3 times (approximately 4 seconds), then you can accept waiting (incoming)
call and hold active call.
13. Summary of button operation
HEADSET STATUS
Button Action
Standby
(No Calls Active)
Incoming Call 1 Call Active
Quick Press (1 Beep) Last number redial Answer Call Close Call
2 seconds (2 Beeps) Initiate Voice Dialing Reject Call
Transfer Active Call
to/from Phone
Multi-function
4 Seconds (3 Beeps) Turn Headset OFF Turn Headset OFF Turn Headset OFF
Quick Press (1 Beep) Increase Volume Increase Volume Increase Volume
2 Seconds (2 Beeps) - - -
Volume UP
4 Seconds (3 Beeps) - - Hold/Resume Call
Quick Press (1 Beep) Decrease Volume Decrease Volume Decrease Volume
2 Seconds (2 Beeps) - - Microphone Mute
Volume DOWN
4 Seconds (3 Beeps) -
-
Close/Resume Call
!
Page 7
PAROS-10 - English
14. Troubleshooting
In case the Headset does not function correctly, please follow the corrective action given in the table below. If the problem is not solved even
after performing the corrective actions, please contact the dealer from whom Headset was purchased.
Status To Check Corrective Action
Headset does not turn on
Check whether the battery of
Headset is charged
Charge the battery
Check whether your mobile phone
supports the “headset” and/or
“hands-free” profile(s)
In order to use the Headset, it is essential that your mobile
phone should support the “headset” and/or “hands-free”
profile(s)
(You might need to search for option such as headset, audio
device, etc in case your mobile phone does not contain the
hands-free option; these options however are subject to the
model of the mobile phone being used)
Unable to communicate using
Headset
Check whether the battery is fully
charged
Charge the battery if the battery power is low
Unable to pair Headset with a
Bluetooth mobile phone
Check whether Headset is on Press MFB for 3 s to turn on Headset
Check whether Headset is in the
pairing mode
With power off, press and hold MFB for at least 6 s to place
Headset in the pairing mode
Page 8
English - PAROS-10
15. Additional Information
(Please read also the supplement “Important Information”
• The cover range of wireless communication is within a maximum range of 30 feet (10 m) and the conditions vary according to
obstacles.
• The Headset can be connected only to those mobile phones that support the Bluetooth headset or hands-free profile(s).
(Subject to different models of mobile phone, it will show you different options such as audio device etc.) This product is not
compatible with the standard cordless phones used in homes.
• As it operates in the same frequency range, the Headset can be affected by the devices that operate in the ISM band (2.402
GHz ~ 2.480 GHz), for example, wireless LAN, microwave devices, medical appliances, etc. Therefore, in order to ensure
proper operation, the hands-free Headset should be away from these devices.
• If handled properly, a rechargeable battery can have a long service life. A new battery or one that has not been used for a long
period of time could have reduced capacity the first few times it is used.
• The standard usage time of the battery can vary depending on the usage condition of the mobile phone and Headset.
16. Safety
• Use the charger that comes with package.
• Caution, risk of explosion if battery is replaced by an incorrect type.
• Check the laws and regulations on the use of mobile phones and hands-free equipment in the areas where you drive. Always
give full attention to driving and pull off the road and park before making or answering a call if driving conditions require.
• Do not allow children to play with your Headset since it contains small parts that could become detached and create a
choking hazard.
• This device contains a Li-polymer battery. Please keep it away from fire anytime (including discarding the device) or the
battery may explode.
• The Headset, especially the embedded battery must be properly disposed or may be recycled, contacts your local recycling
centres for disposal methods.
Page 9
PAROS-10 - English
• Please turn off your Headset in an area with a potentially explosive atmosphere (oil warehouse, explosive warehouse, etc.). In
rare occurrences, this product could generate sparks. This could lead to an explosion or fire, which could result in bodily injury.
Therefore follow the warning notices in those areas carefully.
• Do not drop this unit from a height.
• Do not modify, repair or take apart this unit.
• Do not expose this unit directly to water, alcohol, benzene, etc, for cleaning.
• Do not expose this unit directly to flammables.
• Do not place this unit near flammables.
• Protect this unit from humidity and dust.
• Do not place a heavy object on this unit.
• Please recharge your headset or Headset only if your car stands still. During recharging the headset or Headset cannot be
used.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Other documents
-
AUDIOLINE BT 103 User manual
-
Anycom PAROS-10 User manual
-
Sharper Image Portable Wireless Keyboard and Speaker Owner's manual
-
BlueAnt Wireless X3 MICRO User manual
-
iCreation QMHBT125 User manual
-
Uniden BT229 User manual
-
Uniden BT230 User manual
-
Pyle PHBT6 Owner's manual
-
Cellular Line F3MC User manual
-
i. Tech Dynamic i.VoicePRO Bluetooth Clip Headset User manual
