Kyosho F-16 THUNDER BIRDS (FIGHTING FALCON) User manual
- Type
- User manual
Kyosho F-16 THUNDER BIRDS (FIGHTING FALCON) is a high-performance radio-controlled electric-powered ducted fan aircraft designed for intermediate and advanced flyers. It boasts a 930mm wingspan and comes as a kit that requires assembly before use. The kit includes all the necessary components for assembly, including the airframe, ducted fan unit, motor, and servos. To operate the aircraft, you will need a minimum of a 4-channel proportional radio control system with 4 micro-servos, 1 proportional electronic speed controller, and batteries for the transmitter.
Kyosho F-16 THUNDER BIRDS (FIGHTING FALCON) is a high-performance radio-controlled electric-powered ducted fan aircraft designed for intermediate and advanced flyers. It boasts a 930mm wingspan and comes as a kit that requires assembly before use. The kit includes all the necessary components for assembly, including the airframe, ducted fan unit, motor, and servos. To operate the aircraft, you will need a minimum of a 4-channel proportional radio control system with 4 micro-servos, 1 proportional electronic speed controller, and batteries for the transmitter.
Ni-Cd
SAFETY PRECAUTIONS
First-time builders should seek advice from more experienced persons in order to
assemble the model correctly and realize the full performance potential.
Assemble this kit out of the reach of children.
Take reasonable safety precautions prior to flying this model. You alone are
responsible for the model's correct assembly and safe operation!
Always keep this instruction manual ready at hand for quick reference, even after
completing the assembly.
This radio control model is not a toy!
The product you have purchased is powered by a rechargeable battery. The battery is recyclable. At the end of its useful life, under various national /
state and local laws, it may be illegal to dispose of this battery into the municipal waste stream. Check with your local solid waste officials for details in
your area for recycling options or proper disposal.
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
No. 10002
REQUIRED FOR OPERATION
BEFORE YOU BEGIN
ASSEMBLY
EXPLODED VIEW / SPARE PARTS / OPTION PARTS
OPERATING YOUR MODEL SAFELY
INDEX
WINGSPAN: 930mm
(36.6")
THE FINEST RADIO CONTROL MODELS
R
INSTRUCTION MANUAL
2
3
3~9
10~11
9 / 12
Before commencing assembly, please read these instructions thoroughly.
2000 KYOSHO
For Intermediate & Advanced Flyers
RADIO CONTROLLED ELECTRIC POWERED DUCTED FAN AIRCRAFT
REQUIRED FOR OPERATION
Sharp Hobby Knife
Tools required
( Tools are not included in the kit )
Phillips Screwdriver (L.M.S)
Needle Nose Pliers
(1.7mm)
1.7 mm diameter drill
Awl
Scissors
AAAAAAAA
2
Wire Cutters
Epoxy A
Epoxy B
( 30 )
Epoxy glue with at least 30 minutes curing time
8.4V 1700mAh~2000mAh
7-cell (8.4V) 1700 mAh ~ 2000 mAh Ni-Cd battery
NiCd Battery
3
A charger suitable for your model's 7-cell Ni-Cd battery
Charger
4
Tape
No. 72506 III
Multi Charger III
No. 94752
Clear adhesive waterproof tape
No.71705
8.4V 1800SP
Multi Force Ni-Cd Battery
No.71002
8.4V-RC2400
Ni-Cd Battery
1
4
x4, x1,
Minimum of 4 channel proportional radio control system with
4 micro-servos, 1 proportional electronic speed controller and
batteries for the transmitter.
Minimum 4 channel radio
AA-size Batteries
For proper radio operation, refer to its manual.
30A
Electronic proportional speed controller suitable
for aircraft, with minimum 8.4 V / 30 A continuous
No. 90801
210
SKY VICTORY 210 ESC
Servo
13~13.7mm
28~30mm
29~30mm
Servo "Y" connector
Servo extension lead
(#300~#400 )
Sander: Stick some 300~400 grit sandpaper to a thin piece of ply or similar
No.1829
ROUND CUTTER & SANDER
For trimming canopies, etc.!
Cutting along curved lines never was so easy!
400mm
x 4
x 2
2
TOOLS REQUIRED
Firmly tighten the set screw
to the flats.
2.6 x 6mm
2.6mm
6mm
6mm
3 x 20mm
4 x 4mm
1
2
Ducted Fun Unit
Fuselage
2.6 x 6mm
Screw
2
2.6mm
Washer
2
3 x 20mm
FH Screw
1
3
4 x 4mm
Set Screw
1
6mm
Nut
1
6mm
Washer
2
1
Read through the manual before you begin, so you will have an overall idea of what to do.
Check all parts. If you find any defective or missing parts, contact your local dealer or our Kyosho Distributor.
2
3
Symbols used throughout the instruction manual, comprise:
4
Apply epoxy glue.
Assemble left and right sides
the same way.
Sanding off shaded portion. Must be purchased separately!
2mm
Drill holes with the specified
diameter (here: 2mm).
Cut off shaded portion.
2mm
Do not overlook this symbol!
Pay close attention here!
Warning!
BEFORE YOU BEGIN
The Styrofoam stand included in the kit is
designed for assembly and for flight
preparation of your model. Keep it safely.
Double-sided Tape
Double-sided Tape
Motor Leads
Do not apply glue for
this part.
3
4
Fuselage
Fuselage
4
5
Fuselage
Sanding off shaded portion.
Cut off shaded portion.
Assemble left and right sides
the same way.
2mm
Drill holes with the specified
diameter (here: 2mm).
2mm
Must be purchased
separately!
Pay close attention here!
Apply epoxy glue.
Do not overlook this symbol!
Warning!
72mm 72mm
Warning!
Be sure to glue securely, otherwise
structural failure may occur in flight.
Align the front edge of the main wing with
the corner of the stand.
Cut between the hinges from
Check the hinge marks on the underside.
6mm
Included with the servo.
Elevator Servo
<
>
<
Left
>
<
>
<
Right
>
Bend wire slightly.
Double-sided Tape
2x14mm
Application Sheet
1
.
7
mm
2
mm
6
Fuselage / Horizontal Stabilizer
5
7
Horizontal Stabilizer
2 x 14mm
Screw
4
Sanding off shaded portion.
Cut off shaded portion.
Assemble left and right sides
the same way.
2mm
Drill holes with the specified
diameter (here: 2mm).
2mm
Must be purchased
separately!
Pay close attention here!
Apply epoxy glue.
Do not overlook this symbol!
Warning!
Apply epoxy glue.
Included with the servo.
Aileron Servo
Pass servo lead through hole.
Double-sided Tape
Tape
2x14mm
1
.
7
mm
2
mm
Check the hinge marks on the
underside.
Cut between the hinges from
the topside.
106mm
Warning!
Be sure to glue securely,
otherwise structural failure may
occur in flight .
Pass servo lead through
hole in wing root.
Align the front edge of the main wing with
the corner of the stand.
8
9
Main Wings
Main Wings
6
10
Main Wings / Fuselage
2 x 14mm
Screw
4
Sanding off shaded portion.
Cut off shaded portion.
Assemble left and right sides
the same way.
2mm
Drill holes with the specified
diameter (here: 2mm).
2mm
Must be purchased
separately!
Pay close attention here!
Apply epoxy glue.
Do not overlook this symbol!
Warning!
Warning!
Be sure to glue securely,
otherwise structural failure
may occur in flight.
A = AÕ
AÕA
11mm
Receiver
Electronic Speed
Controller
Double-sided Tape
Doble-saided Tape
2mm
Antenna
Clear Adhesive
Tape
Clear Adhesive Tape
Clear Adhesive Tape
"Y" connector
Extension lead
Electronic Speed Cntroller
Elevator
Aileron
11
13
Vartical Tail
Fuselage
7
12
Fuselage
Sanding off shaded portion.
Cut off shaded portion.
Assemble left and right sides
the same way.
2mm
Drill holes with the specified
diameter (here: 2mm).
2mm
Must be purchased
separately!
Pay close attention here!
Apply epoxy glue.
Do not overlook this symbol!
Warning!
Ni-Cd Battery
19
Adjust the CG correctly and secure
Ni-Cd battery with the strap provided.
Refer to
19
.
"Magic Tape" (Velcro)
14
15
Fuselage
Fuselage
8
16
Decal
Sanding off shaded portion.
Cut off shaded portion.
Assemble left and right sides
the same way.
Must be purchased
separately!
Pay close attention here!
Apply epoxy glue.
Do not overlook this symbol!
Warning!
ELEVATOR
AILERON
6mm
6mm
8mm
8mm
Do not attempt to fly the model before checking the CG.
If the CG isincorrect, you can lose control of the airplane
and cause accidents.
Warning!
CG
100 ~ 110mm
Fuselage
Set the control surface throws as shown in the
diagram, initially. Thesevalues are suitable for
normal flight. Readjust them later according to
your own preferences.
Cut off shaded
portion of the decal.
65mm
5mm
1
.
5
mm
First-time fliers are strongly advised to seek the advice of more experienced pilots, especially regarding assembly
and pre-flight adjustments. Flying a poorly assembled or incorrectly adjusted airplane can be dangerous.
Never fly alone. First-time fliers should always be assisted by an experienced pilot.
18
19
Decal
CG / Control Throws
9
Warning!
Cut off shaded portion.
2mm
Drill holes with the specified
diameter (here: 2mm).
2mm
Pay close attention here!
Apply epoxy glue.
Do not overlook this symbol!
Warning!
18
1 2 3 4 5
DF-1 DF-17
35
3
70951
40
3233
34
DF-1-1
19 18 20
DF-16
DF-16
10
DF-10
38
96441
37
90497
8 DF-10
DF-11W
22 2524 23
DF-12
1311
DF-10
21
DF-12
39
1704
36
DF-18
9 DF-10
14
6
12
7
17
16
DF-11W
DF-11W
DF-18
26
DF-13
DF-10
41
DF-15
28
29
DF-16
18
15
DF-11W
24
< EXPLODED VIEW >
10
No.
No. Part Names Quantity
FOR JAPANESE MARKET ONLY.
FOR JAPANESE MARKET ONLY.
Some of the parts included are not available as spare parts. Purchase
optional parts instead.
DF-1
Ducted Fan Set
3900 270
DF-1-1
( )
Fan (For Ducted Fan)
600 270
DF-10
(F-16)
Fuselage Set (F-16)
6000 TEL
6000 TEL
No.
No. Part Names Quantity
DFW-1
SP
SP Blade Hub
1500 190
DFW-2
SP
SP Aluminum Spinner
1500 190
1
5
90801
SKY VICTORY 210 ESC
9800 TEL
71002
8.4V RC2400
8.4V RC2400 Ni-Cd Battery
8000 TEL
DF-12
(F-16)
Tail Fin Set (F-16)
2600 270
DF-13
(F-16)
Canopy (F-16)
900 270
DF-16
(F-16)
Rod Set (F-16)
1200 190
DF-17
(F-16)
Stand (F-16)
1500 270
DF-18
(F-16)
400 130
70951
AP29L-V
Le mans AP29L-V Special Motor
3500 270
3500 270
90497
Velcro Tape
400 90
1704
Ni-Cd Strap
400 130
96441
1mm
Sponge Tape (1mm)
300 90
6 7 8
9
10 13
x 1
1 2 3 4 5 x 1
3 x 1
26
x 1
x 2 x 4
1211
DF-11W
(F-16 )
Main Wing Set (F-16 THUNDERBIRDS)
14 15
x 1
x 2
16 17 18 19 20
21 22 23 25
x 1 x 2
24
35
x 1
39
x 1
DF-19
(F-16 )
Decal (F-16 THUNDERBIRDS)
32 33 3429
x 2
40
x 1
37
x 1
38
x 1
16 36
x 2
1 set
x 4
28
For a big improvement in flight performance!
Machined aluminum hub fixes the fan blade to the motor shaft using a collet
system. Ensures a tight fit and reduces vibration.
Made from machined stainless steel and aluminum.
Light weight aluminum nut and washer included.
Precision machined aluminum design.
Reduced fan vibration at very high RPM.
Includes spinner retaining bolt.
SPARE PARTS
11
200
OPTION PARTS
200
00
0 0 2 1 0 4 4 7 2 7 1
1 6 8 0
0 0 2 1 0 4
4 7 2 7 1
1 6 8 0
1,400
200
80
1,680
(1)
(2)
(2)
(3)
(4)
(1)
10002
Before Flying Flying After Flying
OFF
ON
Before flying your airplane, ensure
the airfield is spacious enough.
Always fly it outdoors in safe areas
with no debris or obstacles!
For proper radio handling, refer to
its explanations.
Ensure the spinner and propeller
are securely installed.
If the airplane begins to operate by
itself, somebody else is on your fre-
quency. Do not attempt to operate
it under such condition for you may
lose of control of it.
Fully extend
the antenna
(transmitter).
Switch on the transmitter.
Beware of spinning propellers! With
some electronic speed controllers,
the electric motor (propeller) start
spinning as soon as the electronic
speed controller is connected.
Move the sticks on your transmitter
to ensure that all controls move
according to your inputs and the
way you adjusted them.
Only use genuine KYOSHO parts.
ON
Launch your airplane by hand into
the wind.
Do not fly your airplane on days
with strong winds or side winds.
Always land your airplane into the
wind.
WIND
WIND
Ensure the main wing is securely
installed.
Battery
Plug in the Ni-Cd battery.
If your airplane does not function cor-
rectly, land it at once and find out the
reason.
Check the radio batteries.
OFF ON
Switch off the transmitter.
Battery
Unplug the Ni-Cd battery.
OFF
Ba
ttery
Unplug the Ni-Cd battery when not
in use.
Proper maintenance extends the
life of your airplane.
Beware of spinning propellers!
Cautions for Safety
Do not allow watching people to get too
close to a rotating propeller.
Disuse defective propellers as well as
deformed spinners.
BATTER
Y
Battery
Battery
Batteries and chargers become
hot. Do not allow flammable
materials to come in contact with
them.
Never try to modify Ni-Cd battery.
This is very dangerous.
Do not dispose of used Ni-Cd
batteries, return them to the shop.
Do not dispose of Ni-Cd batteries
in a fire. They will explode and
release harmful materials.
Warning!
Warning!
OPERATING YOUR MODEL SAFELY
PRINTED IN JAPAN61920009-1
243 153
TEL.046-229-4115
( ) 10 00 18 00
R
THE FINEST RADIO CONTROL MODELS
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
Kyosho F-16 THUNDER BIRDS (FIGHTING FALCON) User manual
- Type
- User manual
Kyosho F-16 THUNDER BIRDS (FIGHTING FALCON) is a high-performance radio-controlled electric-powered ducted fan aircraft designed for intermediate and advanced flyers. It boasts a 930mm wingspan and comes as a kit that requires assembly before use. The kit includes all the necessary components for assembly, including the airframe, ducted fan unit, motor, and servos. To operate the aircraft, you will need a minimum of a 4-channel proportional radio control system with 4 micro-servos, 1 proportional electronic speed controller, and batteries for the transmitter.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
in other languages
Related papers
-
Kyosho LEAR JET User manual
-
-
-
-
-
-
-
-
-
