Lenovo 30191MU Hardware Replacement Manual

Brand: Lenovo

Model: 30191MU

Type: Hardware Replacement Manual

This manual is also suitable for

Lenovo 30191MU is an advanced multi-mode wireless mouse with up to 1600 dpi resolution for precise cursor control. It includes a USB receiver for wireless connectivity and features 3 programmable buttons for customized functionality. The ergonomic design provides a comfortable grip, even during extended use. It operates on a single AA battery, ensuring long-lasting power.

Version 3.0 2009.11

Hardware Replacement Guide

IdeaCentre K3 Series

31041595

31041595_K3_HRG(H57)_FM_EN_V3.0.1 1 2009.11.17 10:52:54 AM

Hardware Replacement Guide

31041595_K3_HRG(H57)_EN_V3.0.ind1 1 2009.11.17 10:53:23 AM

Contents

Overview ..................................................................................... 1

Chapter 1

Locations ................................................................ 4

Locating components and connectors ...........................................4

Identifying parts on the system board ...........................................7

Chapter 2 Replacing hardware ............................................... 9

General information ........................................................................9

Removing the computer cover ......................................................9

Removing the front bezel .............................................................11

Replacing a memory module ......................................................12

Replacing the hard disk drive .......................................................13

Replacing an optical drive ............................................................14

Replacing the system fan assembly .............................................15

Replacing the heat sink assembly ...............................................18

Replacing a PCI or AGP adapter .................................................20

Replacing the CPU ......................................................................26

Replacing the keyboard ..............................................................29

Replacing the mouse ..................................................................30

Replacing the External speaker ...................................................31

Completing the installation ..........................................................31

Appendix. .................................................................................. 33

31041595_K3_HRG(H57)_EN_V3.0.ind2 2 2009.11.17 10:53:23 AM

Hardware Replacement Guide

Overview

This guide is intended to be used by customers who are replacing Customer

Replaceable Units (CRUs) as well as trained service personnel who are replacing

Field Replaceable Units (FRUs). In this guide, CRUs and FRUs will often be referred

to as parts.

Note: Trained service personnel should refer to the Hardware Maintenance

Manual (HMM) for parts ordering information.

This guide does not include procedures for all parts. It is expected that cables,

switches, and certain mechanical parts can be replaced by trained service

personnel without the need for step-by-step procedures.

Note: Use only parts provided by Lenovo

The description of the TV-Tuner card in this manual applies only to those computer

models that have the TV-Tuner card installed. It does not apply to those computer

models that do not have the TV-Tuner card installed.

This guide contains procedures for replacing the following parts:

• Memory modules

• Hard disk drive

• Optical drive

• Heatsink, Fan

• CPU

• VGA card

• Keyboard, Mouse (wired)

• External speaker

Safety information for replacing CRUs

Do not open your computer or attempt any repair before reading the “Important

safety information” in the Safety and Warranty Guide that was included with your

computer. If you no longer have this copy of the Safety and Warranty Guide, you

can obtain one online from the Support Web site at

http://consumersupport.lenovo.com.

31041595_K3_HRG(H57)_EN_V3.0.ind1 1 2009.11.17 10:53:23 AM

Hardware Replacement Guide

Additional information resources

If you have Internet access, the most up-to-date information for your computer is

available from the World Wide Web.

You can ﬁnd the following information:

• CRU removal and installation information

• Publications

• Troubleshooting information

• Parts information

• Links to other useful sources of information

To access this information, go to http://consumersupport.lenovo.com.

Tools required

To disassemble the computer, you need the following tools:

• Wrist grounding strap and conductive mat for preventing electrostatic

discharge

• Flat screwdriver

• Phillips screwdriver

• Hex screwdriver

• Plastic ﬂat screwdriver

• Plastic tweezers

Note: The screws for the different components vary in size. During the

disassembly procedure, group the screws with their corresponding

components to avoid a mismatch when replacing the components.

Handling static-sensitive devices

Static electricity, although harmless to you, can seriously damage computer

components.

When you are replacing a part, do not open the static-protective package

containing the new part until the defective part has been removed from the

computer and you are ready to install the new part.

When you handle parts and other computer components, take these precautions

to avoid static-electricity damage:

31041595_K3_HRG(H57)_EN_V3.0.ind2 2 2009.11.17 10:53:24 AM

Hardware Replacement Guide

• Limit your movement. Movement can cause static-electricity to build up around

you.

• Always handle parts and other computer components carefully. Handle

adapters, memory modules, system boards, and microprocessors by the

edges. Never touch any exposed circuitry.

• Prevent others from touching the parts and other computer components.

• Before you replace a new part, touch the static-protective package containing

the part to a metal expansion-slot cover or other unpainted metal surface on

the computer for at least two seconds. This reduces static electricity in the

package and your body.

• When possible, remove the new part from the static-protective packaging,

and install it directly in the computer without setting the part down. When this

is not possible, place the static-protective package that the part came in on a

smooth, level surface and place the part on it.

• Do not place the part on the computer cover or other metal surface.

31041595_K3_HRG(H57)_EN_V3.0.ind3 3 2009.11.17 10:53:24 AM

Hardware Replacement Guide

Locations

Chapter

This chapter provides illustrations to help locate the various connectors, controls

and components of the computer. To remove the computer cover, refer to

“Removing the computer cover”.

Locating components and connectors

The following illustrations will help you to locate the various components and

connectors in your computer.

Internal components

The following illustration shows the components inside your computer.

31041595_K3_HRG(H57)_EN_V3.0.ind4 4 2009.11.17 10:53:24 AM

Hardware Replacement Guide

Power supply PCI Express adapter card

System fan Memory modules

Microprocessor fan and heat sink Hard disk drive

PCI Express adapter connector Optical drive

Front view

The following illustrations show the location of connectors on the front of the

computer.

Power button

Power Dial indicator ON/OFF

File backup button

USB connector

Microphone connector

Headphone connector

Memory card reader (selected models only)

31041595_K3_HRG(H57)_EN_V3.0.ind5 5 2009.11.17 10:53:26 AM

Hardware Replacement Guide

Optical drive (Some models are equipped with only one optical drive.)

Power Dial switch

Rear view

The following illustration shows the location of connectors on the rear of the computer.

Voltage selection switch (selected models only)

Power connector

PS/2 keyboard connector

PS/2 mouse connector

On-board VGA connector ( selected models only)

HDMI port

USB connectors (6)

Ethernet connector

SPDIF port

Audio line-out sockets (2)

Audio line-in sockets (2)

31041595_K3_HRG(H57)_EN_V3.0.ind6 6 2009.11.17 10:53:28 AM

Hardware Replacement Guide

Microphone connector

PCI Express x16 graphics adapter connector (Some models are equipped

with this connector. For more information about the graphics adapter, see the

description below).

WiFi antenna connector (This connector only equipped on the model with

WiFi card. For more information about this connector, see WM600-B-LO

Wireless 802. 11b/g Wireless PCI-E Adapter Card User Manual.)

TV-Tuner (selected models only)

Identifying parts on the system board

The system board (sometimes called the planar or motherboard) is the main circuit

board in your computer. It provides basic computer functions and supports a

variety of devices that are factory-installed or that you can install later.

The following illustration shows the locations of parts on the system board.

1817

1112

31041595_K3_HRG(H57)_EN_V3.0.ind7 7 2009.11.17 10:53:28 AM

Hardware Replacement Guide

Microprocessor and heat sink

Memory connectors(2)

Thermal sensor header connector

Power connector

SATA IDE connectors (4)

eSATA connector

Front panel connector

Front USB connectors(2)

Front USB connector

Serial(com2) connector

Front audio connector

PCI apater connector

PCI Express X 1 adapter connectors(2)

PCI Express X 16 graphics adapter connector

System fan connector

Microprocessor fan connector

12V power connector

31041595_K3_HRG(H57)_EN_V3.0.ind8 8 2009.11.17 10:53:29 AM

Hardware Replacement Guide

Attention:

Do not remove the computer cover or attempt any repair before reading the

“Important safety information” in the Safety and Warranty Guide that was

included with your computer or in the Hardware Maintenance Manual (HMM)

for the computer. To obtain copies of the Safety and Warranty Guide or

HMM, go to the Support Web site at http://consumersupport.lenovo.com.

Note: Use only parts provided by Lenovo.

General information

Pre-disassembly instructions

Before proceeding with the disassembly procedure, make sure that you do the

following:

1. Turn off the power to the system and all peripherals.

2. Unplug all power and signal cables from the computer.

3. Place the system on a ﬂat, stable surface.

Removing the computer cover

Attention:

Turn off the computer and wait 3 to 5 minutes to let the computer cool

before removing the computer cover.

To remove the computer cover:

1. Remove any media (diskettes, CDs, or memory cards) from the drives, shut

down your operating system, turn off all attached devices, and the computer.

2. Unplug all power cords from electrical outlets.

Replacing hardware

Chapter

31041595_K3_HRG(H57)_EN_V3.0.ind9 9 2009.11.17 10:53:30 AM

Hardware Replacement Guide

3. Disconnect all cables attached to the computer. This includes power cords,

input/output (I/O) cables, and any other cables that are connected to the

computer. Refer to “Locating connectors on the rear of the computer”.

4. Remove the two screws that secure the computer cover at the rear of the

chassis.

5. Slide the computer cover to the rear of the chassis to remove.

Note: For this procedure, it helps to lay the computer on its side.

31041595_K3_HRG(H57)_EN_V3.0.ind10 10 2009.11.17 10:53:38 AM

Hardware Replacement Guide

Removing the front bezel

To remove the front bezel:

1. Remove the computer cover. Refer to “Removing the computer cover”.

Note: For this procedure, it helps to lay the computer on its side.

2. Remove the front bezel by releasing the three plastic tabs inside the chassis

and push the bezel outward as shown.

3. To reinstall the bezel, align the plastic tabs on the bottom of the bezel with the

corresponding holes in the chassis, and then snap it into position at the bottom

and top of the chassis.

4. Refer to the “Completing the installation”.

31041595_K3_HRG(H57)_EN_V3.0.ind11 11 2009.11.17 10:53:50 AM

Hardware Replacement Guide

Replacing a memory module

Attention:

Do not remove the computer cover or attempt any repair before reading the

“Important safety information” in the Safety and Warranty Guide that was

included with your computer or in the Hardware Maintenance Manual (HMM)

for the computer. To obtain copies of the Safety and Warranty Guide or

HMM, go to the Support Web site at http://consumersupport.lenovo.com.

To replace a memory module:

1. Remove the computer cover. Refer to “Removing the computer cover”.

Note: For this procedure, it helps to lay the computer on its side.

2. Locate the memory module connectors. Refer to “Locating components”.

3. Remove the memory module being replaced by opening the retaining clips as shown.

4. Position the new memory module over the memory connector. Make sure the

notch on the memory aligns correctly with the connector key on the

system board. Push the memory module straight down into the connector until

the retaining clips close.

5. Refer to the “Completing the installation”.

31041595_K3_HRG(H57)_EN_V3.0.ind12 12 2009.11.17 10:53:51 AM

Hardware Replacement Guide

Replacing the hard disk drive

Attention:

Do not remove the computer cover or attempt any repair before reading the

“Important safety information” in the Safety and Warranty Guide that was

included with your computer or in the Hardware Maintenance Manual (HMM)

for the computer. To obtain copies of the Safety and Warranty Guide or

HMM, go to the Support Web site at http://consumersupport.lenovo.com.

To replace the hard disk drive:

1. Remove the computer cover. Refer to “Removing the computer cover”.

Note: For this procedure, it helps to lay the computer on its side.

2. Disconnect the data and power cables from the hard disk drive.

3. Use the plastic handle to slide the hard disk drive out of the drive bay.

4. Slide the new hard disk drive into the drive bay.

5. Pivot in the drive bay in place.

6. Connect the power and signal cables to the hard disk drive. Refer to “Identifying

parts on the system board”.

31041595_K3_HRG(H57)_EN_V3.0.ind13 13 2009.11.17 10:53:59 AM

Hardware Replacement Guide

7. Refer to the “Completing the installation”.

Replacing an optical drive

Attention:

Do not remove the computer cover or attempt any repair before reading the

“Important safety information” in the Safety and Warranty Guide that was

included with your computer or in the Hardware Maintenance Manual (HMM)

for the computer. To obtain copies of the Safety and Warranty Guide or

HMM, go to the Support Web site at http://consumersupport.lenovo.com

To replace an optical drive

1. Remove the computer cover. Refer to “Removing the computer cover”.

2. Remove the front bezel. Refer to “Removing the front bezel”.

3. Disconnect the data and power cables from the rear of the optical drive.

4. Press the release button and push the optical drive straight out of the front of

the chassis.

31041595_K3_HRG(H57)_EN_V3.0.ind14 14 2009.11.17 10:54:08 AM

Hardware Replacement Guide

5. Slide the new optical drive into the bay from the front until it snaps into

position.

6. Connect the data and power cables to the drive.

7. Install the front bezel. Refer to the steps 3 of the “Removing the front bezel”.

8. Install the computer cover. Refer to “Completing the installation”.

Replacing the system fan assembly

Attention:

Do not remove the computer cover or attempt any repair before reading the

“Important safety information” in the Safety and Warranty Guide that was

included with your computer or in the Hardware Maintenance Manual (HMM)

for the computer. To obtain copies of the Safety and Warranty Guide or

HMM, go to the Support Web site at http://consumersupport.lenovo.com

To replace the system fan assembly:

1. Remove the computer cover. Refer to “Removing the computer cover”.

2. Locate the system fan assembly. Refer to “Identifying parts on the system

board”.

3. Disconnect the system fan assembly cable from the system board. Refer to

“Identifying parts on the system board”.

31041595_K3_HRG(H57)_EN_V3.0.ind15 15 2009.11.17 10:54:09 AM

Hardware Replacement Guide

4. Pull the system fan assembly out of chassis.

31041595_K3_HRG(H57)_EN_V3.0.ind16 16 2009.11.17 10:54:09 AM

Hardware Replacement Guide

5. Install the new system fan assembly by aligning the rubber mounts of the

system fan assembly with the holes on the chassis and push the rubber

mounts through the holes.

6. Pull on the tips of the rubber mounts until the fan assembly is in place.

7. Connect the system fan assembly cable to the system fan connector on the

system board.

8. Refer to the “Completing the installation”.

31041595_K3_HRG(H57)_EN_V3.0.ind17 17 2009.11.17 10:54:18 AM

Page is loading ...

Lenovo 30191MU Hardware Replacement Manual

Brand: Lenovo

Model: 30191MU

Type: Hardware Replacement Manual

This manual is also suitable for

Download PDF

report

Lenovo 30191MU Hardware Replacement Manual

This manual is also suitable for

Lenovo 30191MU Hardware Replacement Manual

Related papers

Other documents