JL Audio C3-600 Owner's manual

Brand: JL Audio

Model: C3-600

Category: Car speakers

Type: Owner's manual

This manual is also suitable for

Evolution C3-600

JL Audio C3-600: Experience exceptional sound with these versatile 6-inch component speakers, meticulously crafted for automotive excellence. Immerse yourself in crystal-clear audio with a frequency response ranging from 50Hz to 25kHz, ensuring every note is reproduced with precision. Enjoy customizable sound with adjustable tweeter level and midrange presence to tailor your listening experience to perfection. Installation flexibility is key, with options for component or coaxial configurations, allowing you to achieve the ideal soundstage for your vehicle.

OWNER’S MANUAL

6-inch (150 mm) Convertible 2-Way Component System

Thank you for choosing a JL Audio Evolution™ C3 Convertible

Component System for your automotive sound system.

These Evolution™ Speakers have been designed and manufactured to

exacting standards in order to ensure years of musical enjoyment in your

vehicle. For maximum performance and extended warranty

coverage, we highly recommend that you have your new speakers installed

by an authorized JL Audio dealer. Your authorized

dealer has the training, expertise and installation equipment to ensure

optimum performance from this product. Should you

decide to install the speakers yourself, please take the time

to read this manual thoroughly so as to familiarize yourself

with its installation requirements and setup procedures.

If you have any questions regarding the instructions in this

manual or any aspect of your amplifier’s operation, please contact your

authorized JL Audio dealer for assistance. If you need further assistance,

please call the JL Audio Technical Support Department

at (954) 443-1100 during business hours.

2 | JL Audio - C3-600 Owner’s Manual 3

Woofer Physical Dimensions

Frame Outer Diameter (A) 6.21 in. / 157.7 mm

Grille Tray Outer Diameter (B) 6.46 in. / 164.1 mm

Rear Cover Outer Diameter (C) 4.08 in. / 103.6 mm

Frontal Tweeter Protrusion* (D) 0.81 in. / 20.6 mm

Frontal Grille Protrusion (E) 1.03 in. / 26.2 mm

Mounting Hole Diameter (F) 5.00 in. / 127 mm

Mounting Depth (G) 2.49 in. / 63 mm

Crossover Network Physical Dimensions

Height (A) 4.72 in. / 119.9 mm

Width (B) 3.36 in. / 85.3 mm

Depth (C) 1.44 in. / 36.6 mm

C3-600 SPECIFICATIONS

Woofers: Injection-Molded Polymer Frame, Patented Elevated

Frame Cooling (U.S. Patent #6,219,431 & #6,229,902), DMA-

Optimized Motor System, Mineral-Filled Polypropylene Cone,

Rubber Surround, 1.2-in. / 31 mm Voice Coil, Kapton® Former,

Low-Profile, Symmetrical Roll Spider, Ferrite Magnet

Tweeters: 1.00 in. / 25 mm Silk Soft Dome with Ferrofluid

Cooling and Damping and Neodymium Magnet

Fixed Angle Flush-Mount, Surface-Mount and Coaxial-Mount

Systems

Crossover Networks: 2-way networks with 1st order

low-pass and 3rd order high-pass filters, premium Mylar®

capacitors, air-core inductors, 4-position adjustable tweeter

output level, 3-position midrange presence control,

Polyswitch tweeter protection

Continuous Power Handling: 75 Watts (RMS Method)

Frequency Response: 50 Hz - 25 KHz (± 3 dB)

Efficiency @ 1W/1m: 89.5 dB @ 1W/1m

Nominal Impedance: 4 ohms

Included Components and Parts:

• Two C3-600cw 6-inch (150 mm) Woofers

• Two C3-100ct 1.00-inch (25 mm) Tweeters

• Two C3-600-XO Crossover Networks

• Two Surface-Mount Tweeter Fixtures

• Two Coaxial-Mount Tweeter Fixtures

• Two Flush-Mount Tweeter Fixtures

• Two Metal Spring Clips for Tweeter Fixtures

• Two Metal Mesh Woofer Grilles with ABS Grille Trays

• Twelve #8 x 1.25 inch (32 mm) Sheet Metal Screws

• Four #6 x 1.00-inch (25 mm) Sheet Metal Screws

• Two 1.00-inch (25 mm) Machine Screws

• Eight Mounting Clips for Woofer Mounting

• Two 6.4 mm Female Crimpable Connectors

• Two 4.7 mm Male Crimpable Connectors

• Two 4.7 mm Female Crimpable Connectors

• Four 2.8 mm Female Crimpable Connectors

• Two 2.8 mm Male Crimpable Connectors

• Twelve Crimpable Spade Connectors

• One Woofer Mounting Template

Tweeter Fixture Physical Dimensions Flush-Mount Surface-Mount

Fixture Outer Diameter (A) 2.12 in. / 53.8 mm 1.93 in. / 49.0 mm

Fixture Mounting Hole Diameter (B) 1.875 in. / 47.6 mm N/A

Fixture Mounting Depth (C) 0.71 in. / 18.0 mm N/A

Tweeter Frontal Protrusion (D) 0.32 in. / 8.1 mm 0.95 in. / 24.1 mm

Due to ongoing product development, all specifications are subject to change without notice.

4 | JL Audio - C3-600 Owner’s Manual 5

Amplier

Output

RedBlack

Amplier

Output

Red Black

GETTING STARTED

•Turnofftheaudiosystem.Itisalso

advisabletodisconnectthenegative(–)

terminalofyourvehicle’sbatterywhenever

performinginstallationwork.

•Beforecutting,drillingorinsertinganyscrew,

checkclearancesonbothsidesoftheplanned

mountingsurface.Alsocheckforanypotential

obstacles,suchaswindowtracksandmotors,

wiringharnesses,etc.Checkbothsidesofthe

vehicle,manyvehiclesarenotsymmetrical!

•Alwayswearprotectiveeyewear.

CROSSOVER NETWORK INSTALLATION

ThecrossovernetworkssuppliedwithyourC3

Systemshouldbeinstalledinadrylocationinside

yourvehicle.DONOTINSTALLTHEMINSIDEOF

ADOOR!Doorsoftengetwetontheinside,which

candamageyourcrossovernetworksandcould

potentiallydamageyourentiresoundsystem.The

crossoverscanbescrewedintoasolidsurfaceviatwo

holeslocatedundertheprotectivecoverofthecase.

Toaccesstheseholes,simplysqueezethesidesofthe

coverwhilegentlypullingthecoverawayfromthe

base.Makesurethatyourmountinglocationwillnot

causedamagetowiring,fuellines,brakelinesorany

othervitalcomponentofyourvehicle.Onceyouhave

screwedthecaseinandmadeyourconnections,snap

theprotectivecoverbackintoplace.

TWEETER PROTECTION

TheC3crossovernetworksareequippedwith

anadvancedelectronictweeterprotectioncircuit

designedtominimizethepossibilityoftweeter

failure.Thiselectronicdevicemonitorscurrentgoing

tothetweeterandwilldisconnectthetweeterfrom

thesignalwhenitsensesoverload.Shouldthisoccur

whilelisteningtotheaudiosystem,simplyreducethe

volumeforafewsecondsandtheprotectioncircuit

willresetitselfautomatically.



CROSSOVER NETWORK ADJUSTMENT

Thecrossovernetworkshavebeendesignedto

allowtonaladjustmentstotheuppermidrange

responseandtweeterlevel.Theseadjustmentsmake

itpossibletofine-tuneyoursystemtosuityour

listeningpreferencesandtocompensateforvarious

speakermountingapplications.

ADJUSTABLE MIDRANGE PRESENCE

YourC3crossovernetworksprovideaunique

midrangepresencecontrol,locatedunderthecover.

Themidrangepresenceisselectableviaasetofpins

andallowsforthreesettings.Thesesettingsaffectthe

amplitudeoftheuppermidrangeresponseoftheC3

componentwoofer.Werecommendthatyoubegin

yourlisteninginthe“REF”(Reference)andadjust

upordownasneededtocompensateformounting

location,orientationorpersonaltaste.

ADJUSTABLE TWEETER LEVEL

C3crossovernetworksalsoprovidefourlevels

oftweeteradjustabilitydesignedtocompensatefor

differentmountinglocations,vehicleinteriorsand

personaltaste.Theselevelsareselectableviaasetof

pinslocatedundertheclearcoverofeachcrossover

case.Werecommendthatyoubeginlisteninginthe

“REF”(Reference)position.Tofindtheoptimum

tonalbalanceinyourinstallation,experimentwith

alternatetweeterlevelsettingsbymovingthepins.It

issafetoswitchjumperswhilethesystemisplaying.

WIRING YOUR SPEAKER SYSTEM

C3ConvertibleComponentsgiveyoutheoption

ofinstallingthespeakersasseparatecomponent

speakersystemsorascoaxialsystems(tweeters

mountedontothecenterofeachwoofer).

Positive(+)andnegative(–)connectionstothe

crossoverfromtheamplifieroutputsaremadewith

theterminalslabeled“IN+”and“IN–”.ThePositive

andNegativeoutputstothewooferconnectionsare

labeled“W+”and“W–”ontheCrossoverandshould

beconnectedtocorresponding“WFR+”and

“WFR–”terminalsonthewoofer(asillustrated

below).Thetweeterconnectionsvarybysystem

configurationandmaybemadeinoneoftwoways.

Incomponentconfiguration,thetweeteroutputs,

labeled“T+”and“T–”ontheCrossovershouldbewired

directlytothecorrespondingleadonthetweeter(See

DiagramA).Incoaxialconfiguration,thetweeteris

connectedviaaninternaljumper(Seepage6formore

information)andtheCrossovertweeteroutputsshould

bewiredtothecorresponding“TWT+”and“T W T–”

terminalsonthewoofer(SeeDiagramB).

WARNING

It is absolutely vital that your component system

is connected as shown in this manual. Failure to

connect the system as shown may result in damage to

your speakers which is NOT covered under warranty.

Do not substitute different crossover networks into

your C3 System. Do not use crossover networks

intended for different C3 models.

DIAGRAM B: Coaxial System Wiring

DIAGRAM A: Component System Wiring

6 | JL Audio - C3-600 Owner’s Manual 7

CONVERTIBLE COMPONENTS

C3ConvertibleComponentsgiveyoutheoption

ofinstallingthespeakersasseparatecomponent

speakersystemsorascoaxialsystems(tweeters

mountedontothecenterofeachwoofer).

Note: If the C3 system is to be used in a coaxial

configuration, the phase plugs must be removed to

accept the tweeter and tweeter post.

Component System Set-Up

TheComponentconfigurationoftheC3-600

isachievedbywiringthetweetertothecrossover

separatelyandinstallingtheincludedphaseplugs

ontothecenterofeachwoofer.The woofers are

factory-packaged in the component system

configuration with phase plugs installed.

Thephaseplugsattachtothewoofersusinga

simplebayonet(twistandlock)mechanism.

Toremovethephaseplugs,simplyapply

downwardpressurewithyourthumbandindex

fingerandtwist1/4turncounteclockwiseuntil

released.Thenpullthephaseplugoffthereceiver.

Toreattachthephaseplugs,alignthetwo

tabsontheinsideofeachphaseplugwiththe

groovesontheouterdiameterofthereceiver

inthecenterofthewoofer.Withthesealigned,

slidethephaseplugdownintoplaceuntilit

stops,applyinggentlepressure.Tolock,push

downfirmly/evenlyontheplugwiththumband

indexfingerandturn1/4turnclockwise.

Forwoofermountinginstructions,pleaserefer

toPages10-11ofthisManual.Forseparatetweeter

mountinginstructions,pleaserefertoPages12-13of

thisManual.

Coaxial System Set-Up

TheCoaxialconfigurationoftheC3-600is

achievedbyinstallingatweeterontothecenterof

eachwooferusingthesuppliedcoaxialtweeterposts.

First,removethephaseplugsfromthewoofers(if

present)bypushingdownfirmly/evenlyontheplug

withthumbandindexfingerandturning1/4turn

counter-clockwisetounlockandremove.Thephase

plugswillnotbeusedincoaxialconfigurationand

shouldbesetasideforpossiblefutureuse.

Next,routethetweeter’sPositive(+)and

Negative(-)wireleadsthroughthecenterofthe

coaxialtweeterpostfromthelargetweeter-cupend

andoutthesmallerend(SeeFigureA).Thetweeter

mountstothecoaxialtweeterpostusingasimple

bayonet(twistandlock)mechanism.Toattachthe

tweetertothepost,observetheindentedlocking

slotsontheouteredgeofthetweeterbodyandalign

thesewiththetabsvisibleontheinsidewallsofthe

tweetercupportionofthetweeterpost.Thetweeter

shouldslideintoplaceeasilyandcanthenbelocked

bypushingdownonthetweeterandgivingitasmall

clockwiseturn(SeeFigureB).

Withthetweeterinstalledintothetweeterpost,

connectthePositive(+)redwireleadonthetweeter

tothelargermaleconnectiontabinthewoofer’s

center,followedinthesamemanner,bythe

Negative(-)blackleadtothesmallerconnectiontab.

(SeeFigureC).

Now,notethetwotabsontheinsideofthebottom

endofthetweeterpost.Alignthesetabstothe

channelsvisibleonoppositesidesofthereceiverin

thewoofer’scenter.Whiletuckingthewiresintothe

tweeterpost,slidethetweeterpostdownintoplace

untilitstopsandisreadytobelocked.Tolock,push

downfirmly/evenlyonthetweeterpostwiththumb

andindexfingerandturn1/4turnclockwise.

(SeeFigureD).

Forwoofermountinginstructions,pleasereferto

Pages10-11ofthisManual.

DIAGRAM C: Tweeter Post / Coaxial System Configuration

DIAGRAM D: Phase Plug / Component System Configuration

FigureA.

FigureC.

FigureB.

FigureD.

8 | JL Audio - C3-600 Owner’s Manual 9

COAXIAL PLACEMENT CONSIDERATIONS

Inmostcases,speakersinthecoaxial

configurationwillbeplacedintofactoryspeaker

locations.Ifyouhavesomespeakermounting

flexibility,keepthefollowinginmind:Lower

mountinglocations,suchasthelowerfrontcorner

(SeeDiagramF)ofadoororakick-panelprovide

thegreatestpathlengthdistancesforthesound

emittedbythespeakers.Forthisreason,theyare

generallymoredesirablethanhighermounting

locations.Highermountinglocationswillusually

resultinextremenear-sidesoundstagebiaswhich

compromisesthestereolisteningexperience

(SeeDiagramE).



COMPONENT PLACEMENT CONSIDERATIONS

Acomponentsystemconfigurationgivesyouthe

abilitytoplacethewooferandtweeterseparately

inyourvehicleinterior.Thiscanbegoodorbad,

dependingonhowit’sdone.Asageneralrule,the

tweetersshouldbeplacedrelativelyclosetothe

woofersforbesttonalbalanceandmostcoherent

imaging(thecloser,thebetter).Anyseparation

greaterthan8inches(20cm)islikelytoresultin

degradedsoundquality(SeeDiagramH).

Avoidplacingtweeterswheretheywillbeblocked

DIAGRAM F: COAXIAL CONFIGURATION  More Desirable Door Speaker Placement

DIAGRAM E: COAXIAL CONFIGURATION - Less Desirable Door Speaker Placement

byobjectsintheinteriorofthecar(includingseated

occupants).Whenselectingamountinglocation,

lookatbothsidesofthecartomakesurethatthis

locationisclearonbothsides.

Youcanalwaysexperimentwithtweeter

placementbeforecommittingtoafinalmounting

location.Simplyconnecttherestofthesystemand

allowplentyofwirelengthforthetweeters.Using

Velcro®orsimilarmaterial,attachthetweetersin

differentlocationsuntilyoufindtheonewherethey

performbest.

Wooferswillusuallybeplacedintofactory

speakerlocations.Ifyouhavesomewoofermounting

flexibility,keepthefollowinginmind:Lower

mountinglocations,suchasthelowerfrontcornerof

adoor(SeeDiagramH)orakick-panelprovidethe

greatestpathlengthdistancesforthesoundemitted

bythewoofer.Forthisreason,theyaregenerally

moredesirablethanhighermountinglocations.

Highermountinglocationsoftenresultinextreme

near-sidesoundstagebiaswhichcompromisesthe

stereolisteningexperience

(SeeDiagramG).

DIAGRAM H: COMPONENT CONFIGURATION  More Desirable Door Speaker Placement

DIAGRAM G: COMPONENT CONFIGURATION  Less Desirable Door Speaker Placement

10 | JL Audio - C3-600 Owner’s Manual 11

Custom Location:Runspeakerwiretothedesired

mountinglocations.Ifyouarerunningwiresinto

adoor,useexistingfactorywiringbootswhenever

possible.Ifyouaredrillingnewholes,filetheiredges

andinstallrubbergrommetsintoeachhole.Wires

shouldthenbecoveredwithaprotective,flexible

PVCsleeveandthenrunthroughthedoorjamb.

Makesurethatthewireswillcleardoorhingesand

otherstructuresinthedoor.Ifyouareunsureabout

anypartofthisprocess,pleasecontactyourJLAudio

dealerforinstallationhelp.

Selectanevensurface.Tighteningaspeakeronto

anunevensurfacecandamageit.Usethesupplied

templatetomarkthedesiredmountinglocation.

Markthecenterandtheoutlineofthemounting

holeaswellasthemountingscrewpositions.Before

drillingorcuttingonyourinteriorpanels,usea

utilityknifetocutanyfabric,vinylorleatherfrom

holelocations.Thesematerialscaneasilybesnagged

byadrillorasaw,causingdamagetothepaneland

possiblebodilyinjury.Drillapilotholeinthecenter

oftheproposedspeakermountinghole.Then,using

asabersawwithanappropriateblade,makethe

circularcutoutforthespeaker.Fileanyroughedges.

Aftercuttingthehole,checktoseethatthe

speakerframefitsintoitsmountingholecleanly.

Donotforcetheframeintoaholethatistoosmall.

Oncethespeakerisinplace,usetheholesonthe

speaker’smountingflangetomarkthepanelwhere

thefourmountingscrewswillbepositioned(See

DiagramJ).Removethespeakeranddrill1/8-inch

(3mm)holesateachmark.Insertthemounting

clipswiththeflatsidetowardsthespeaker.Connect

thespeakerwires,observingcorrectpolarity,and

securethespeakerandgrilletraytothepanelby

evenlytighteningbyhandtheprovided#8x1.25

inch(32mm)mountingscrews.Makesurethe

wooferissecuredsothatairdoesnotleakaround

themountingflange.Airleakswillcauseasevere

degradationinsoundquality.Sealanyairleaks

withanautomotive-gradesealantmaterial.

WARNING



Double check the clearance for both speakers

before proceeding. Many cars are different from

one side to the other!

WOOFER INSTALLATION

Thewoofersshouldbeinstalledinoneofthe

followingwaysdependingonlocation:



Factory Location:Ifyouwillbeusingthefactory

speakerwires,itmaybenecessarytochangethe

terminations.Thismaybeaccomplishedbyusing

anadaptorplugorsimplybycuttingthefactory

connectoroffandusingthesuppliedcrimp

connectorstoterminatethespeakerwires.The

largeconnectorisforthepositive(+)terminaland

thesmallconnectorisforthenegative(–)terminal

ofeachwoofer.Keepinmindthatthewooferwires

mustbeconnectedtothewooferoutputsofthe

crossoverssuppliedwithyoursystemasshowninthe

diagramonpage5.Ifyouprefertorunnewwires,

refertothe“CustomLocation”installationsection

fordetails.Whichevermethodyouchoose,observe

correctpolarityinyourconnections.Ifyouare

unsureaboutanyoftheseissues,contactyour

JLAudiodealerforinstallationassistance.

Yournewspeakershavebeendesignedtoinstall,

withoutmodifications,intomostvehiclesthataccept

a6-inch(150mm)speaker.Mostfactory6-inch

speakersusefourmountingscrewswhichwilllineup

withthemountingholesonyourwoofers.

Itisabsolutelyvitalthatthespeakerframe

fitsintothemountingholecleanly.Thismustbe

checkedpriortotighteningthescrews.Donot

forcetheframeintoaholethatistoosmall.Do

nottightenthespeakerontoanunevensurface.

Thiswilldamageyourspeakers.Thespeaker

shouldalsofitsothatairdoesnotleakaround

themountingflange.Airleakswillcauseasevere

degradationinsoundquality.Sealanyairleaks

withanautomotive-gradesealantmaterial.

Usethesuppliedmountingclipsunlessthefactory

holesalreadyfeaturethreadedinserts.

Hand-tightenthescrewsevenly(SeeDiagramI).

DIAGRAM J: Custom Location Woofer Installation

DIAGRAM I: Factory Location Woofer Installation

WARNING

Hand-tighten the screws evenly in a criss-cross

pattern to avoid bending the speaker frame or

stripping the mounting clips.

12 | JL Audio - C3-600 Owner’s Manual 13

DIAGRAM K: Flush-Mount Tweeter Installation

Surface-Mount Installation

Inthisapplication,youwillnotneedtocut

largeholesinyourvehicle’spanelsforthetweeters.

Youwillonlyneedtodrillaholeforthewiresand

twosmallerholesforthemountingscrews.This

applicationisusefulwhenmountingthetweetersto

apanelthathasinsufficientclearancebehinditfor

thetweeter’smagnetstructure.

Usingthefixtureasatemplate,markthescrew

holelocationsandalocationinthecenterofthe

fixtureforthewirehole.Removethefixtureand

drillpilotholesforthescrewsanda1/4-inch(6.4

mm)forthewires.Usethesupplied#6x1.00-inch

sheetmetalscrewstosecurethefixtureasshownin

DiagramL.Next,routethetweeter’spositive(+)and

negative(-)wireleadsthroughthe1/4-inchcenter

hole.Thetweeterissecuredtothefixtureusinga

simplebayonet(twistandlock)mechanism.Toattach

thetweetertothesurface-mountfixture,observethe

indentedlockingslotsontheouteredgeofthetweeter

bodyandalignthesewiththetabsvisibleonthe

insidewallsofthefixture.Thetweetershouldslide

intoplaceeasilyandcanthenbelockedbypushing

downonthetweeterandgivingitasmallclockwise

turn(SeeDiagramL).

TWEETER INSTALLATION

First,runspeakerwiresfromthetweeteroutput

ofthecrossover(seeWiringDiagramBonpage5)

tothedesiredtweetermountinglocations,observing

thesameprecautionsasmentionedinthewoofer

installationsection.Terminatethewireswiththe

supplied2.8mmmalecrimpableconnectors.

TWEETER FIXTURE INSTALLATION:

Thedometweeterssuppliedwithyour

C3-600systemhavebeendesignedformaximum

mountingversatilityinacomponentconfiguration.

Therearetwoprimarymethodsbywhichthe

tweeterscanbemountedinyourvehicle:

Flush-Mount Installation

Thedometweeterssuppliedwithyour

C3-600systemhavebeendesignedtointegratewith

yourinstallationinaclean,unobtrusivemanner

usingaflush-mountcup.Thiscompactmounting

fixtureisinstalledusingthemethodillustratedin

DiagramKandrequiresamountingholewitha

diameterof1.875in.(47.6mm).

Atleast1.70-inch(43.2mm)ofclearanceis

requiredbehindthemountingsurfaceofthetweeter

forthespringclipsand1-inchmachinescrews

usedinmountingthefixture.Inlimiteddepth

applications,itmaybenecessarytocutdownthe

lengthofthemachinescrew,ortouseashorterscrew

(notsupplied).Hand-tightenthemachinescrewuntil

thefixtureissecure(SeeDiagramK).

DIAGRAM L: Surface-Mount Tweeter Installation

14 | JL Audio - C3-600 Owner’s Manual 15

NOTES NOTES

LIMITED WARRANTY  AUTOMOTIVE SPEAKER SYSTEMS USA

JLAUDIOwarrantsthesespeakers(andcrossovernetworks,whereapplicable)tobefreeofdefectsin

materialsandworkmanshipforaperiodofone (1) year.

Thiswarrantyisnottransferableandappliesonlytotheoriginalpurchaserfromanauthorized

JLAUDIOdealer.Shouldservicebenecessaryunderthiswarrantyforanyreasonduetomanufacturing

defectormalfunction,JLAUDIOwill(atitsdiscretion),repairorreplacethedefectiveproductwithnewor

remanufacturedproductatnocharge.Damagecausedbythefollowingisnotcoveredunderwarranty:accident,

misuse,abuse,productmodificationorneglect,failuretofollowinstallationinstructions,unauthorizedrepair

attempts,misrepresentationsbytheseller.Thiswarrantydoesnotcoverincidentalorconsequentialdamages

anddoesnotcoverthecostofremovingorreinstallingtheunit(s).Cosmeticdamageduetoaccidentornormal

wearandtearisnotcoveredunderwarranty.

Anyapplicableimpliedwarrantiesarelimitedindurationtotheperiodoftheexpresswarrantyasprovided

hereinbeginningwiththedateoftheoriginalpurchaseatretail,andnowarranties,whetherexpressorimplied,

shallapplytothisproductthereafter.Somestatesdonotallowlimitationsonimpliedwarranties,therefore

theseexclusionsmaynotapplytoyou.Thiswarrantygivesyouspecificlegalrights,andyoumayalsohaveother

rightswhichvaryfromstatetostate.



If you need service on your JL AUDIO product:

AllwarrantyreturnsshouldbesenttoJLAUDIOfreightprepaidthroughanauthorizedJLAUDIO

dealerandmustbeaccompaniedbyproofofpurchase(acopyoftheoriginalsalesreceipt.)Direct

returnsfromconsumersornon-authorizeddealerswillberefusedunlessspecificallyauthorizedby

JLAUDIOwithavalidreturnauthorizationnumber.Warrantyexpirationonproductsreturned

withoutproofofpurchasewillbedeterminedfromthemanufacturingdatecode.Coveragemaybe

invalidatedasthisdateisprevioustopurchasedate.Returnonlydefectivecomponents.Ifonespeaker

failsinasystem,returnonlythatspeakercomponent,nottheentiresystem.Non-defectiveitems

receivedwillbereturnedfreight-collect.Customerisresponsibleforshippingchargesandinsurance

insendingtheproducttoJLAUDIO.Freightdamageonreturnsisnotcoveredunderwarranty.

For Service Information in the U.S.A. please call

JL Audio Customer Service: (954) 443-1100

9:00 AM – 5:30 PM (Eastern Time Zone)

JL Audio, Inc

10369 North Commerce Pkwy.

Miramar, FL 33025

(do not send product for repair to this address)

International Warranties:

Products purchased outside the United States of America are covered only

by that country’s distributor and not by JL Audio, Inc.

Printed in China C3-600-040512

JL Audio C3-600 Owner's manual

Brand: JL Audio

Model: C3-600

Category: Car speakers

Type: Owner's manual

This manual is also suitable for

Evolution C3-600

Download PDF

report

JL Audio C3-600 Owner's manual

This manual is also suitable for

JL Audio C3-600 Owner's manual

Related papers

Other documents