2. AME International
  3. 51025

AME International 51025 Owner's manual

  • Hello! I've reviewed the instruction sheet for the AME Tire Valve Tool model 51025. This document describes how to replace valve stems without removing the tire from the wheel using a T-handle, plunger rod, and insertion cone. It also specifies that the tool is only for use with .453 valve stems and not for tires with TPMS. I'm ready to answer your questions about this tool and the process.
  • Can this tool be used on all tire valve stems?
    Can this tool be used on tires with TPMS?
    Are new valve stems included with the tool?
AME TIRE VALVE TOOL
ITEM # 51025
AME TIRE VALVE TOOL
ITEM # 51025
Ideal
for
Tire Valve
Recalls
Ideal
for
Tire Valve
Recalls
REPLACE THE VALVE STEM WITHOUT
REMOVING THE TIRE FROM THE WHEEL
www.ameintl.net
877-755-4AME(4263)
A TIRE VALVE
IN
SECONDS
1. Deflate tire if not already flat. Insert
T-Handle between rim and valve stem.
2. Turn T-Handle 1/4 turn to hook valve
stem and pull out.
3. Thread new valve stem on end of
plunger rod. Apply tire/rubber lubricant
to the base of the valve stem.
4. Position insertion cone over stem hole.
5. Push plunger rod / valve stem
assembly completely through insertion
cone.
6. Pull back to seat valve stem
and un-thread.
Not to be used on tires with
TPMS – Tire Pressure Mounting
Systems. Valve stems not included.
AME TIRE VALVE TOOL
ITEM # 51025
AME TIRE VALVE TOOL
ITEM # 51025
Ideal
for
Tire Valve
Recalls
Ideal
for
Tire Valve
Recalls
REPLACE THE VALVE STEM WITHOUT
REMOVING THE TIRE FROM THE WHEEL
www.ameintl.net
877-755-4AME(4263)
A TIRE VALVE
IN
SECONDS
1. Deflate tire if not already flat. Insert
T-Handle between rim and valve stem.
2. Turn T-Handle 1/4 turn to hook valve
stem and pull out.
3. Thread new valve stem on end of
plunger rod. Apply tire/rubber lubricant
to the base of the valve stem.
4. Position insertion cone over stem hole.
5. Push plunger rod / valve stem
assembly completely through insertion
cone.
6. Pull back to seat valve stem
and un-thread.
Not to be used on tires with
TPMS – Tire Pressure Mounting
Systems. Valve stems not included.
AME TIRE VALVE TOOL
ITEM # 51025
Instruction Sheet
Replace the Valve Stem Without
Removing the Tire From the Wheel
AME International
2324 Circuit Way Brooksville, FL 34604
Phone: 352-799-1111 | Toll Free: 877-755-4AME (4263)
Fax: 352-799-1112
E-mail: [email protected] | Web: www.ameintl.net
WARNING: WEAR EYE PROTECTION!
1. Deflate tire if not already
flat. Insert T-Handle between
rim and valve stem.
2. Turn T-Handle 1/4 turn to
hook valve stem and pull out.
3. Thread new valve stem on
end of plunger rod. Apply
tire/rubber lubricant to the
base of the valve stem.
4. Position insertion cone
over stem hole.
5. Push plunger rod / valve
stem assembly completely
through insertion cone.
6. Pull back to seat valve stem
and un-thread.
• For use with .453 valve stems only.
• Not to be used with 5/8” valve stems.
• Not to be used on tires with TPMS - Tire Pressure Mounting Systems.
• Valve stems not included.
Plunger Rod
Valve Stem
Lubricant
Insertion
Cone
T-Handle
AME TIRE VALVE TOOL
ITEM # 51025
Instruction Sheet
Replace the Valve Stem Without
Removing the Tire From the Wheel
AME International
2324 Circuit Way Brooksville, FL 34604
Phone: 352-799-1111 | Toll Free: 877-755-4AME (4263)
Fax: 352-799-1112
E-mail: [email protected] | Web: www.ameintl.net
WARNING: WEAR EYE PROTECTION!
1. Deflate tire if not already
flat. Insert T-Handle between
rim and valve stem.
2. Turn T-Handle 1/4 turn to
hook valve stem and pull out.
3. Thread new valve stem on
end of plunger rod. Apply
tire/rubber lubricant to the
base of the valve stem.
4. Position insertion cone
over stem hole.
5. Push plunger rod / valve
stem assembly completely
through insertion cone.
6. Pull back to seat valve stem
and un-thread.
• For use with .453 valve stems only.
• Not to be used with 5/8” valve stems.
• Not to be used on tires with TPMS - Tire Pressure Mounting Systems.
• Valve stems not included.
Plunger Rod
Valve Stem
Lubricant
Insertion
Cone
T-Handle
/