SeaLevel DuoCom User manual

Brand: SeaLevel

Model: DuoCom

Type: User manual

DUOCOM™

User Manual | 3088

Contents

CONTENTS ........................................................................................................................................................... 2

INTRODUCTION ................................................................................................................................................... 3

BEFORE YOU GET STARTED ............................................................................................................................... 4

CARD SETUP ........................................................................................................................................................ 6

INSTALLATION .................................................................................................................................................... 9

TECHNICAL DESCRIPTION ............................................................................................................................... 11

SPECIFICATIONS ............................................................................................................................................... 12

APPENDIX A – TROUBLESHOOTING................................................................................................................ 13

APPENDIX B – HOW TO GET ASSISTANCE ..................................................................................................... 14

APPENDIX C – ELECTRICAL INTERFACE ........................................................................................................ 15

APPENDIX D – ASYNCHRONOUS COMMUNICATIONS .................................................................................. 16

APPENDIX E – SILK-SCREEN ............................................................................................................................ 17

APPENDIX F – COMPLIANCE NOTICES ........................................................................................................... 18

WARRANTY ........................................................................................................................................................ 20

Introduction

Overview

The Sealevel Systems DUOCOM: provides the PC with 2 Asynchronous serial ports providing a versatile

interface for common RS-232 needs (i.e., modem, mouse, and plotters).

Before You Get Started

What’s Included

The DUOCOM is shipped with the following items. If any of these items are missing or damaged, please

contact Sealevel for replacement.

• DUOCOM Serial I/O Adapter

Advisory Conventions

Warning

The highest level of importance used to stress a condition where damage could result to the

product, or the user could suffer serious injury.

Important

The middle level of importance used to highlight information that might not seem obvious or a

situation that could cause the product to fail.

Note

The lowest level of importance used to provide background information, additional tips, or other

non-critical facts that will not affect the use of the product.

Factory Default Settings

The DUOCOM factory default settings are as follows:

Port # Base Address IRQ

Port 1 280 5

Port 2 288 10

To install the DUOCOM using factory default settings, refer to Installation.

For your reference, record installed DUOCOM settings below:

Port # Base Address IRQ

Card Setup

The DUOCOM contains several jumper straps that must be set for proper operation.

Address Selection

Each serial port on the DUOCOM: occupies eight consecutive I/O locations and looks to the PC as a

standard serial port. A DIP switch (SW1) is used to set the port address options for the DUOCOM:. Be careful

when selecting the port addresses as some selections may conflict with existing ports. The following table

shows the addressing options available with the standard PAL. If you do not see an address option that

suits your needs, please contact Sealevel Systems Technical Support about a custom PAL option.

Port1

Port2

SW1

3F8 2F8 On On On Off

3E8 2E8 On On Off On

2F8 2E8 On On Off Off

2F8 3E8 On Off On On

3220 3228 On Off On Off

4220

4228

Off

5220 5228 On Off Off Off

5220 4220 Off On On On

280 290 Off On On Off

300 308 Off On Off On

310 318 Off On Off Off

280

288

Off

290

298

Off

300 280 Off Off Off On

Disabled Disabled Off Off Off Off

Figure 1 - Address Selection Table

Each COM: port in your system should have a unique address. Typically, COM1: - COM4: addresses

are 3F8, 2F8, 3E8 & 2E8 Hex. If a COM1: & COM2: are already present, use the second addressing

option, this will provide the typical addresses for COM3: & COM4:

Refer to Appendix A for common address contentions.

IRQ Selection

Headers E1 and E2 select the interrupt request for each serial port (E1 - Port 1, E2 - Port 2). If COM1: is

selected, the corresponding jumper must be on the IRQ4 setting. If COM2: is selected, the corresponding

jumper must be on IRQ3.

Most communications software applications default COM3: to IRQ4 and COM4: to IRQ3. This

requires the sharing of interrupts between COM1: and COM3:, and between COM2: and COM4:.

While this is the default, it is not always the preferred setting. Check your software configuration

instructions to determine the most appropriate IRQ selection.

Figure 2 - Header E1 and E2, IRQ Selection

Any two or more ports can share a common IRQ by placing the jumpers on the same IRQ setting and setting

the appropriate selections at E3. Consult your particular software for IRQ selection. If no interrupt is desired,

remove the jumper.

2/9 3 4 5 7 10 11 12 15

Interrupt Modes

Header E3 selects the interrupt mode for each port. Each port must be set in the correct mode to insure

proper installation.

‘N’ indicates the (N)ormal, single interrupt per port mode. ‘S’ Indicates the (S)hared interrupt mode, which

allows more than one port to access a single IRQ. Any two or more ports can share a common IRQ by

placing the jumpers on the same IRQ setting and setting the appropriate selections at E1. Consult your

particular software for IRQ selection. If no interrupt is desired, remove the jumper. ‘R’ indicates the inclusion

of a 1K ohm pull-down resistor required on one port when sharing interrupts.

Figure 3 - Header E3, Normal IRQ Mode

Set the jumpers to ‘S’ for shared interrupt mode on all blocks sharing an IRQ. Also set one block for ‘R.’ This

provides the pull-down resistor circuit that makes sharing of IRQs possible. If you are using more than one

DUOCOM: or a compatible adapter in a bus you should only have one port set to ‘R.’ The following example

shows both ports sharing a single IRQ.

Figure 4 - Header E3, Shared IRQ Mode

Set the jumper to ‘S’ if you are using more than one DUOCOM: in a bus or you wish to completely remove

the pull-down resistor for hardware compatibility. Setting the adapter in this configuration when it is not

accompanied by a pull-down resistor will prevent the ports from triggering an interrupt.

Figure 5 - Header E3, Sharing IRQ’s with another adapter

N S R

Installation

Operating System Installation

For Windows Users

Do not install the Adapter in the machine until the software has been fully installed.

Only users running Windows 7 or newer should utilize these instructions for accessing and installing

the appropriate driver via Sealevel’s website. If you are utilizing an operating system prior to

Windows 7, please contact Sealevel by calling 864.843.4343 or emailing [email protected] to

receive access to the proper driver download and installation instructions.

Begin by locating, selecting, and installing the correct software from the Sealevel software driver database.

1. Select the Part Number (3088) for your device from the listing.

2. Click ‘Download Now’ for the version of SeaCOM compatible with your system.

3. The setup file will automatically detect the operating environment and install the proper

components. Follow the information presented on the installation screens that follow.

4. A screen may appear with the declaration: “The publisher cannot be determined due to the

problems below: Authenticode signature not found.” Please select the ‘Yes’ button and proceed

with the installation. This declaration simply means that the Operating System is not aware of the

driver being loaded. It will not cause any harm to your system.

5. During setup, you may specify installation directories and other preferred configurations. This

program also adds entries to the system registry that are necessary for specifying the operating

parameters for each driver. An uninstall option is included to remove the driver and all registry/INI

file entries from your system.

6. Proceed with the physical installation of your SeaLINK USB serial adapter.

Windows NT is not USB aware and thus cannot support this device.

System Installation

The DUOCOM: can be installed in any of the PC expansion slots, but to access the ‘AT’ or (E)ISA IRQs (10 -

15) it must be installed in one of the 16 bit slots. The DUOCOM: contains several jumper straps for each

port which must be set for proper operation prior to installing the adapter into the computer.

1. Turn off PC power. Disconnect the power cord.

2. Remove the PC case cover.

3. Locate an available slot and remove the blank metal slot cover.

4. Gently insert the DUOCOM: into the slot. Make sure that the adapter is seated properly.

5. Replace the screw.

6. Replace the cover.

7. Connect the power cord.

Installation is complete.

Technical Description

The DUOCOM: utilizes the 16550 UART. This chip features programmable baud rate, data format, interrupt

control and a 16 byte input and output FIFO. Also available as an option is the 16C650 UART that provides

a deeper FIFO (32 bytes) and enhanced clocking features.

Features

• Addressable as COM1: - COM4: and other selectable address combinations.

• ‘Shareable’ IRQs allow more than one port to share a single IRQ.

• IRQs 2-5, 7, 10, 11, 12, 15 supported.

Connector Pin Assignments (DB9 Male)

Signal Name Pin # Mode

TD Transmit Data 3 Output

RTS Request To Send 7 Output

DTR Data Term Ready 4 Output

GND Ground 5

RD Receive Data 2 Input

DCD Data Carrier Detect 1 Input

DSR Data Set Ready 6 Input

CTS Clear To Send 8 Input

RI Ring Indicator 9 Input

These assignments meet EIA/TIA/ANSI-574 DTE for DB-9 type connectors.

Please terminate any control signals that are not going to be used. The most common way to do

this is connect RTS to CTS and RI. Also, connect DCD to DTR and DSR. Terminating these pins, if

not used, will help insure you get the best performance from your adapter.

Specifications

Environmental Specifications

Specification Operating Storage

Temperature Range 0º to 50º C (32º to 122º F) -20º to 70º C (-4º to 158º F)

Humidity Range 10 to 90% R.H. Non-Condensing 10 to 90% R.H. Non-Condensing

Manufacturing

All Sealevel Systems Printed Circuit boards are built to UL 94V0 rating and are 100% electrically tested.

These printed circuit boards are solder mask over bare copper or solder mask over tin nickel.

Power Consumption

Supply line +12 VDC -12 VDC +5 VDC

Rating 50 mA 50 mA 195 mA

Mean Time Between Failures (MTBF)

Greater than 150,000 hours. (Calculated)

Physical Dimensions

Board length 5.4 inches (13.72 cm)

Board height including Goldfingers 3.5 inches (8.89 cm)

Board height excluding Goldfingers 3.2 inches (8.13 cm)

Appendix A – Troubleshooting

Serial Utility test software is supplied with the Sealevel Systems adapter and will be used in the

troubleshooting procedures. By using this software and following these simple steps, most common

problems can be eliminated without the need to call Technical Support.

1. Identify all I/O adapters currently installed in your system. This includes your on-board serial ports,

controller cards, sound cards etc. The I/O addresses used by these adapters, as well as the IRQ (if

any) should be identified.

2. Configure your Sealevel Systems adapter so that there is no conflict with currently installed adapters.

No two adapters can occupy the same I/O address.

3. Make sure the Sealevel Systems adapter is using a unique IRQ The IRQ is typically selected via an

on-board header block. Refer to the section on Card Setup for help in choosing an I/O address and

IRQ.

4. Make sure the Sealevel Systems adapter is securely installed in a motherboard slot.

5. When running DOS, Windows 3.x or other operating systems refer to the Serial Utilities software for

that operating system and the User Manual to verify that the Sealevel Systems adapter is configured

correctly. The supplied software contains a diagnostic program 'SSD' that runs under DOS and will

verify if an adapter is configured properly. This diagnostic program is written with the user in mind

and is easy to use. Refer to the DIAG.txt file in the dos\diag directory for detailed instructions on

using 'SSD'.

6. For Windows 95/98 and Windows NT, the diagnostic tool 'WinSSD' is installed in the Sealevel folder

on the Start Menu during the setup process. First find the ports using the Device Manager, then use

'WinSSD' to verify that the ports are functional.

7. Always use the Sealevel Systems diagnostic software when troubleshooting a problem. This will help

eliminate any software issues and identify any hardware conflicts.

8. The following are known I/O conflicts:

• The 278 and 378 settings may conflict with your printer I/O adapter.

• 3B0 cannot be used if a Monochrome adapter is installed.

• 3F8-3FF is typically reserved for COM1:

• 2F8-2FF is typically reserved for COM2:

• 3E8-3EF is typically reserved for COM3:

• 2E8-2EF is typically reserved for COM4:

If these steps do not solve your problem, please call Sealevel Systems’ Technical Support, (864) 843-4343.

Our technical support is free and available from 8:00 AM to 5:00 PM Eastern Time Monday through Friday.

For email support contact support@sealevel.com.

Appendix B – How To Get Assistance

Please refer to Troubleshooting Guide prior to calling Technical Support.

1. Begin by reading through the Troubleshooting Guide in Appendix A. If assistance is still needed

please see below.

2. When calling for technical assistance, please have your user manual and current adapter settings.

If possible, please have the adapter installed in a computer ready to run diagnostics.

3. Sealevel Systems provides an FAQ section on its web site. Please refer to this to answer many

common questions. This section can be found at http://www.sealevel.com/faq.htm .

4. Sealevel Systems maintains a Home page on the Internet. Our home page address is

www.sealevel.com. The latest software updates, and newest manuals are available via our FTP

site that can be accessed from our home page.

5. Technical support is available Monday to Friday from 8:00 a.m. to 5:00 p.m. eastern time. Technical

support can be reached at (864) 843-4343. For email support contact support@sealevel.com.

RETURN AUTHORIZATION MUST BE OBTAINED FROM SEALEVEL SYSTEMS BEFORE RETURNED

MERCHANDISE WILL BE ACCEPTED. AUTHORIZATION CAN BE OBTAINED BY CALLING SEALEVEL

SYSTEMS AND REQUESTING A RETURN MERCHANDISE AUTHORIZATION (RMA) NUMBER.

Appendix C – Electrical Interface

RS-232

Quite possibly the most widely used communication standard is RS-232. This implementation has been

defined and revised several times and is often referred to as RS-232 or EIA/TIA-232. The IBM PC computer

defined the RS-232 port on a 9 pin D sub connector and subsequently the EIA/TIA approved this

implementation as the EIA/TIA-574 standard. This standard is defined as the 9-Position Non-Synchronous

Interface between Data Terminal Equipment and Data Circuit-Terminating Equipment Employing Serial Binary

Data Interchange. Both implementations are in widespread use and will be referred to as RS-232 in this

document. RS-232 is capable of operating at data rates up to 20 Kbps at distances less than 50 ft. The

absolute maximum data rate may vary due to line conditions and cable lengths. RS-232 is a single ended

or unbalanced interface, meaning that a single electrical signal is compared to a common signal (ground)

to determine binary logic states. The RS-232 and the EIA/TIA-574 specification define two types of interface

circuits, Data Terminal Equipment (DTE) and Data Circuit-Terminating Equipment (DCE). The DUOCOM: is

a DTE device.

Appendix D – Asynchronous Communications

Serial data communications implies that individual bits of a character are transmitted consecutively to a

receiver that assembles the bits back into a character. Data rate, error checking, handshaking, and

character framing (start/stop bits) are pre-defined and must correspond at both the transmitting and

receiving ends.

Asynchronous communications is the standard means of serial data communication for PC compatibles

and PS/2 computers. The original PC was equipped with a communication or COM: port that was designed

around an 8250 Universal Asynchronous Receiver Transmitter (UART). This device allows asynchronous

serial data to be transferred through a simple and straightforward programming interface. A start bit,

followed by a pre-defined number of data bits (5, 6, 7, or 8) defines character boundaries for asynchronous

communications. The end of the character is defined by the transmission of a pre-defined number of stop

bits (usually 1, 1.5 or 2). An extra bit used for error detection is often appended before the stop bits.

Figure 6 - Asynchronous Communications Bit Diagram

This special bit is called the parity bit. Parity is a simple method of determining if a data bit has been lost

or corrupted during transmission. There are several methods for implementing a parity check to guard

against data corruption. Common methods are called (E)ven Parity or (O)dd Parity. Sometimes parity is not

used to detect errors on the data stream. This is referred to as (N)o parity. Because each bit in

asynchronous communications is sent consecutively, it is easy to generalize asynchronous

communications by stating that each character is wrapped (framed) by pre-defined bits to mark the

beginning and end of the serial transmission of the character. The data rate and communication

parameters for asynchronous communications have to be the same at both the transmitting and receiving

ends. The communication parameters are baud rate, parity, number of data bits per character, and stop bits

(i.e., 9600, N, 8, 1).

Appendix E – Silk-Screen

5.0"

3.9"

4.2"

Appendix F – Compliance Notices

Federal Communications Commission (FCC) Statement

This equipment has been tested and found to comply with the limits for Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the equipment is operated in a

residential installation. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instruction manual, may cause

harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one or

more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

EMC Directive Statement

Products bearing the CE Label fulfill the requirements of the EMC directive (89/336/EEC)

and of the low-voltage directive (73/23/EEC) issued by the European Commission. To obey

these directives, the following European standards must be met:

• EN55022 Class B - “Limits and methods of measurement of radio interference

characteristics of information technology equipment”

• EN55024 – “Information technology equipment Immunity characteristics Limits

and methods of measurement”.

Always use cabling provided with this product if possible. If no cable is provided or if an alternate

cable is required, use high quality shielded cabling to maintain compliance with FCC/EMC directives.

Caution

Sealevel Systems, Inc. is not responsible for any radio or television interference caused by unauthorized

modifications of this equipment or the substitution of attachment of connecting cables and equipment

other than those specified by Sealevel Systems. Such unauthorized modifications, substitutions, or

attachments may void the user’s authority to operate the equipment. The correction of interference caused

by such unauthorized modifications, substitutions, or attachments will be the responsibility of the user.

Always use cabling provided with this product if possible. If no cable is provided or if an alternate cable is

required, use high quality shielded cabling to maintain compliance with FCC directives.

Canadian Radio Interference Regulations

This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment

Regulations.

Cet Appareil numérique de la classe B respecte toutes les exigences de Règlement sur le matériel du

Canada.

Warranty

Sealevel's commitment to providing the best I/O solutions is reflected in the Lifetime Warranty that is

standard on all Sealevel manufactured I/O products. We are able to offer this warranty due to our control

of manufacturing quality and the historically high reliability of our products in the field. Sealevel products

are designed and manufactured at its Liberty, South Carolina facility, allowing direct control over product

development, production, burn-in and testing. Sealevel achieved ISO-9001:2015 certification in 2018.

Warranty Policy

Sealevel Systems, Inc. (hereafter "Sealevel") warrants that the Product shall conform to and perform in

accordance with published technical specifications and shall be free of defects in materials and

workmanship for the warranty period. In the event of failure, Sealevel will repair or replace the product at

Sealevel's sole discretion. Failures resulting from misapplication or misuse of the Product, failure to adhere

to any specifications or instructions, or failure resulting from neglect, abuse, accidents, or acts of nature

are not covered under this warranty.

Warranty service may be obtained by delivering the Product to Sealevel and providing proof of purchase.

Customer agrees to ensure the Product or assume the risk of loss or damage in transit, to prepay shipping

charges to Sealevel, and to use the original shipping container or equivalent. Warranty is valid only for

original purchaser and is not transferable.

This warranty applies to Sealevel manufactured Product. Product purchased through Sealevel but

manufactured by a third party will retain the original manufacturer's warranty.

Non-Warranty Repair/Retest

Products returned due to damage or misuse and Products retested with no problem found are subject to

repair/retest charges. A purchase order or credit card number and authorization must be provided in order

to obtain an RMA (Return Merchandise Authorization) number prior to returning Product.

How to obtain an RMA (Return Merchandise Authorization)

If you need to return a product for warranty or non-warranty repair, you must first obtain an RMA number.

Please contact Sealevel Systems, Inc. Technical Support for assistance:

Available Monday – Friday, 8:00AM to 5:00PM EST

Phone 864-843-4343

Email support@sealevel.com

Trademarks

Sealevel Systems, Incorporated acknowledges that all trademarks referenced in this manual are the service

mark, trademark, or registered trademark of the respective company.

SeaLevel DuoCom User manual

SeaLevel DuoCom User manual

SeaLevel DuoCom User manual

Related papers