AMG Systems Ltd. reserves the right to make changes to this
document without notice. The information herein is believed to
be accurate. No responsibility is assumed by AMG for its use.
Page 1 of 12 AMG5914-2A9R Instruction Sheet
D22184-00.doc
AMG5914-
2A9R
Instruction Manual
Single Channel Video Receive Unit with two Bi-directional
Data Channels, 2 Bi-directional Audio Channels, eight Bi-
directional Alarms plus Ethernet for a Singlemode Fibre
Link
The AMG5914-2A9R is a rackmount one channel video receive unit designed to receive 1 video signal
and transmit and receive 2 data signals, 2 audio channels plus 8 bi-directional alarms and also
provides full duplex 100Base-T Ethernet connectivity over one Singlemode optical fibre.
The AMG5914-2A9R is designed to plug into an AMG2009 or AMG2015 subrack, which in turn fits
into a 19" rack system.
The AMG5914-2A9R is designed to operate with an AMG5913-2A9 or AMG5913-2A9R video
transmit unit in a point to point configuration. The R suffix in the partno. indicates a rackmount
configuration.
AMG Systems Ltd. reserves the right to make changes to this
document without notice. The information herein is believed to
be accurate. No responsibility is assumed by AMG for its use.
Page 2 of 12 AMG5914-2A9R Instruction Sheet
D22184-00.doc
Contents
Introduction 3
Unit Functional Schematic .............................................................................................................. 3
Optical Connection ......................................................................................................................... 3
Ethernet Operation ......................................................................................................................... 3
Connections 4
Power Connection .......................................................................................................................... 4
Video Output Connections ............................................................................................................. 4
Optical Connection Singlemode ..................................................................................................... 4
Data and Alarm Channel Connections ............................................................................................ 4
Audio Connections ......................................................................................................................... 4
Ethernet Connection ...................................................................................................................... 5
Front Panel Indicators 6
Power LED .................................................................................................................................... 6
Low Speed Data LEDs ................................................................................................................... 6
Alarm LEDs ................................................................................................................................... 6
Ethernet Data LEDs ....................................................................................................................... 6
Audio LEDs .................................................................................................................................... 6
Data and Alarm Channel Configuration 8
Data Channel Configuration ........................................................................................................... 8
Data Interface Connections ............................................................................................................ 8
Data Channel Termination ............................................................................................................. 8
Alarm Channel Configuration ......................................................................................................... 9
Alarm Channel Circuit .................................................................................................................... 9
Alarm Interface Connections ........................................................................................................ 10
Audio Channel Configuration 11
Audio Channel Configuration........................................................................................................ 11
Audio Interface Connections Ch1 & Ch2 ...................................................................................... 11
Physical Information 12
Dimensions .................................................................................................................................. 12
Mounting Details .......................................................................................................................... 12
Safety 12
Maintenance and Repair 12
AMG Systems Ltd. reserves the right to make changes to this
document without notice. The information herein is believed to
be accurate. No responsibility is assumed by AMG for its use.
Page 3 of 12 AMG5914-2A9R Instruction Sheet
D22184-00.doc
Introduction
Unit Functional Schematic
The
AMG5914
-
2A9R
receives 1 video, 2
data channels, 2 bi-directional audio
signals and 8 bi-directional alarm signals
from the AMG5913-2A9 transmit unit.
It also transmits 2 data channels, 2 bi-
directional audio signals and 8 bi-
directional alarms to the AMG5913-2A9.
Ethernet connectivity is also provided
between the two units.
Optical Connection
The AMG5914-2A9R connections are illustrated in the following example which shows an AMG5913-
2A9 transmit unit together with an AMG5914-2A9R rackmount receive unit configured as a single
channel point to point system.
Ethernet Operation
The Ethernet interface supports 100Mbit/s full duplex operation only. Data is transmitted from one port
the other port with minimum delay or buffering.
The port implements "Auto MDI/MDIX" i.e. it may be connected with either a straight-though or cross-
over cable to an appropriate device such as external switch, PC or other DCE/DTE.
Two LED indicators are provided adjacent to the RJ-45 port: Green indicates Link / Data transfer and
Yellow indicates no Ethernet connection.
AMG Systems Ltd. reserves the right to make changes to this
document without notice. The information herein is believed to
be accurate. No responsibility is assumed by AMG for its use.
Page 4 of 12 AMG5914-2A9R Instruction Sheet
D22184-00.doc
Connections
Power Connection
Connector Type ................................. Removable 2-pin, 3.81mm, Screw Terminal
Connector Partno. .............................. Phoenix 1803578
Supply Voltage................................... +12 to +15 Volts DC
Maximum Power ................................ 5 Watts
Video Output Connections
Connectors ........................................ 75 ohm BNC Socket.
Output Impedance ............................. 75 ohm terminated.
Output Level ...................................... 1 Volt p-p nominal
Frequency Response ......................... 10Hz to 7MHz.
Optical Connection Singlemode
Optical Fibre ...................................... Singlemode
Connector .......................................... SC/PC
Primary Optical Launch Power ........... -10dBm
Transmit Wavelength ......................... 1550nm
Primary Optical Sensitivity.................. -30dBm
Receive Wavelength .......................... 1310nm
Minimum Optical Dynamic Range ...... 20dB.
Data and Alarm Channel Connections
No. of Data Channels ......................... 2
No. of Alarms ..................................... 8
Connectors ........................................ Removable 5-pin, 3.5mm, Spring Terminal
Connector Partnos. ............................ Phoenix 1952296
Data Interfaces .................................. RS-232 / 422 / 485. Selected by external slide switches D1-D2
RS-232 – Switch Position - Top
RS-422 – Switch Position - Middle
RS-485 – Switch Position - Bottom
Internal 120Ω termination resistors may be applied to RS-422 or RS-485 inputs as required by internal
DIL switches inside the enclosure. *See appropriate section on how to remove the case for access to
the DIL switches.
Alarm inputs....................................... Input is via a series 10k resister with 47kΩ pull-up to +3V3.
Alarm outputs .................................... Output is NPN open collector, maximum load 500mA @ 24Vdc.
Audio Connections
No. of Audio Channels ....................... 2
Connectors ........................................ Removable 5-pin, 2.5mm, Spring Terminal
Connector Partno. .............................. Phoenix 1881354
Input level .......................................... 0dBm
Input overload level ............................ +6dBm
AMG Systems Ltd. reserves the right to make changes to this
document without notice. The information herein is believed to
be accurate. No responsibility is assumed by AMG for its use.
Page 5 of 12 AMG5914-2A9R Instruction Sheet
D22184-00.doc
Input impedance ................................ 10kΩ / 600Ω
Output impedance .............................. 600Ω
Frequency response ......................... 10Hz to 20KHz
Audio Input impedance is selected by removable jumper JP1 or JP2 on Audio Expansion board inside
enclosure. *See appropriate section on how to remove the case for access to the data/audio switches.
1-2 – High Impedance 10kΩ
2-3 – Balanced 600Ω
Ethernet Connection
Ethernet Data Connector ................... RJ45
Interface ............................................ Auto MDI/MDIX 100BASE-TX
Ethernet Data Rate ............................ Maximum 100Mb/s full duplex
AMG Systems Ltd. reserves the right to make changes to this
document without notice. The information herein is believed to
be accurate. No responsibility is assumed by AMG for its use.
Page 6 of 12 AMG5914-2A9R Instruction Sheet
D22184-00.doc
Front Panel Indicators
Power LED
POWER ............................................. Green - Power is present
Off - Power is not present
VIDEO ............................................. Green - Video output signal is present
Off - Video input signal is not present
OPTO TX ........................................... Green - Tx opto. present
Off - Tx opto. is not present
OPTO RX .......................................... Green - Rx opto. sync.
Off - Rx opto. is not sync.
Low Speed Data LEDs
Data Present IN (RS485 or RS422) .... Green - logic zero (+V, -V) present on IN+, IN-
Red - logic one (-V,V+) present on IN+, IN-
Off - tri-state off or no connection on IN+, IN-
Data Present IN (RS232) ................... Green - logic zero (+V) present on input IN+
Red - logic transitions present on input IN+
Off - logic one (-V) present on input IN+
IN corresponds to the data signals being transmitted onto the optical fibre.
Data Present OUT (RS485 or RS422) Green - logic zero (+V,-V) present on OUT+, OUT-
Red - logic one (-V,+V) present on OUT+, OUT-
Off - tri-state off or no connection on OUT+, OUT-
Data Present OUT (RS232) ............... Green - logic zero (+V) present on OUT+
Red - logic transitions present on OUT+
Off - logic one (-V) present on OUT+
OUT corresponds to the data signals being received from the optical fibre.
Alarm LEDs
Channels 1-8
ALARM IN ......................................... Green - Alarm ON / Contacts closed.
Off - Alarm OFF / Contacts open.
ALARM OUT ...................................... Green - Alarm ON / Contacts closed.
Off - Alarm OFF / Contacts open.
Ethernet Data LEDs
Link not Present ................................ Yellow - Link not present
Off - Link is present
Link Integrity ...................................... Green - Link integrity is good, Idle state
GBlink - Data transfer
Off - Link not present
Audio LEDs
AMG Systems Ltd. reserves the right to make changes to this
document without notice. The information herein is believed to
be accurate. No responsibility is assumed by AMG for its use.
Page 7 of 12 AMG5914-2A9R Instruction Sheet
D22184-00.doc
Audio Present TX ............................... Green - audio present > -40dBm
Red - audio present > 0dBm (overload at +6dBm)
Off - audio not present or < -40dBm
This represents the audio signals being transmitted on the optical fibre
Audio Present RX .............................. Green - audio present > -40dBm
Red - audio present > 0dBm (overload at +6dBm)
Off - audio not present or < -40dBm
This represents the audio signals being received from the optical fibre.
AMG Systems Ltd. reserves the right to make changes to this
document without notice. The information herein is believed to
be accurate. No responsibility is assumed by AMG for its use.
Page 8 of 12 AMG5914-2A9R Instruction Sheet
D22184-00.doc
Data and Alarm Channel Configuration
The AMG5914-2A9R receive unit sends and receives data to/from an AMG5913-2A9 or rackmount
equivalent AMG5913-2A9R transmit unit. The 2 physical data interfaces RS-485, RS-422 or RS-232
are individually selectable by the user with the slide switch mounted from the rear panel.
There are also 8 bi-directional alarm inputs provided, each alarm input is typically connected to a
contact closure switch. Each alarm output can receive an on/off signal from an AMG5913-2A9 and is
typically used to convey contact closure status.
Data Channel Configuration
Each low speed data channel provides an RS-232, RS-422 (full duplex, four wire) or RS-485 (half
duplex, two wire) interface defined by the corresponding mode switch inside the enclosure. Every data
channel as shipped from the factory is set up for RS-485 operation unless otherwise requested.
The data input for both the RS-485 and the RS-422 modes detects a tri-state input condition by
monitoring the differential voltage level across the input. A differential level below 600mV positive or
negative will be detected as a tri-state condition. A level above 600mV positive or negative will be
detected as a logic 1 or logic 0 respectively. It is important therefore to terminate the RS-485 bus or
the RS-422 input bus using 120Ω if a pre-bias is present on the RS-485 or RS-422 bus.
A large number of third party equipment manufacturers apply a pre-bias on their RS-485 bus. This pre-
bias is applied by pulling one arm of the RS-485 bus high (+5 volts) and the other arm low (0 volts)
using high value resistors within the third party equipment. In order to ensure that the AMG equipment
detects a tri-state condition, then these resistors should have a value above 5kΩ. If the third party
bias resistors are less the 750Ω the bus can be multiple terminated as required to ensure that a tri-
state level is detected.
The system detects a tri-state input condition on the data channel bus when in RS-485 or RS-422
mode.
Data Interface Connections
Connector
Pin No.
Data Channel
RS-485
[switch bottom] RS-422
[switch middle] RS-
232
[switch top]
1 IN/OUT - (B) OUT - (B) OUT
2 IN/OUT + (A) OUT + (A)
3 GND GND GND
4 IN - (B)
5 IN + (A) IN
Note: (A) or (B) in brackets in the above table refers to RS-485 / RS-422 data specification.
Data Channel Termination
The interface mode RS-232, RS-422 or RS-485 of each data port Data 1-4, is selected with the
corresponding external slide switch D1-D4. The actual number of data channels provided on the unit
depends upon the AMG model.
Internal 120Ω termination resistors across IN+ and IN- inputs may also be applied when in RS-422 or
RS-485 mode using internal DIP switches P0-P3 on the main PCB inside the enclosure. P0-P3 may
AMG Systems Ltd. reserves the right to make changes to this
document without notice. The information herein is believed to
be accurate. No responsibility is assumed by AMG for its use.
Page 9 of 12 AMG5914-2A9R Instruction Sheet
D22184-00.doc
be accessed by removing the 2 fixing screws in the rear panel and sliding the PCB out of the
enclosure.
For clarity, in the 3 examples shown below all 4 data ports D1-D4 are terminated the same, but each
data channel may be configured & terminated independently as required. The 3 examples shown are
RS-232 (no termination), RS-422 (120Ω) or RS-485 (120Ω).
Alarm Channel Configuration
The AMG5914-2A9R provides 8 bi-directional contact closure inputs / alarm outputs.
Each ALARM IN input is via an internal 10kΩ series resistor with a 47kΩ pull-up resistor to the internal
+3V3 supply.
Each ALARM OUT output can receive an on/off signal from an AMG5913-2A9 and is typically used to
convey contact closure status. Each alarm output is NPN open collector, maximum load 500mA /
24Vdc.
Alarm Channel Circuit
The output of each alarm channel is an NPN open collector transistor circuit, with an absolute
maximum rating of 1A / 60V. There is a common GND for all alarm channels.
AMG Systems Ltd. reserves the right to make changes to this
document without notice. The information herein is believed to
be accurate. No responsibility is assumed by AMG for its use.
Page 10 of 12 AMG5914-2A9R Instruction Sheet
D22184-00.doc
The alarm output circuit is designed for low dc voltage / low current operation and has minimal internal
protection. If an alarm output is used to drive an external relay circuit, the external crcuit MUST include
a protection (flyback) diode connected across the relay to prevent the high voltage generated from a
back EMF causing damage due to the AMG output transistor.
Alarm Interface Connections
Connector Pin
No.
Alarm Interfaces
Alarm IN
1-4, 5-8
Alarm OUT
1-4 , 5-8
1 ALARM 1/5 IN ALARM 1/5 OUT
2 ALARM 2/6 IN ALARM 2/6 OUT
3 GND GND
4 ALARM 3/7 IN ALARM 3/7 OUT
5 ALARM 4/8 IN ALARM 4/8 OUT
AMG Systems Ltd. reserves the right to make changes to this
document without notice. The information herein is believed to
be accurate. No responsibility is assumed by AMG for its use.
Page 11 of 12 AMG5914-2A9R Instruction Sheet
D22184-00.doc
Audio Channel Configuration
Audio Channel Configuration
The AMG5914-2A9R provides two bi-directional audio channels.
Each audio channel input can be configured as a single-ended high impedance 10kΩ input with GND
reference or alternativly as a balanced 600Ω input pair. The input impedance is selected using
jumpers on the audio expansion board JP1 (Channel 1) or JP2 (Channel 2), the default setting is
balanced 600Ω.
JP1/JP2 1-2 – High Impedance 10kΩ
JP1/JP2 2-3 – Balanced 600Ω
Audio Interface Connections Ch1 & Ch2
Connector Pin
No.
Balanced Input
600Ω High Z input 10kΩ
1 OUT - OUT -
2 OUT + OUT +
3 GND GND
4 IN + IN
5 IN - GND
AMG Systems Ltd. reserves the right to make changes to this
document without notice. The information herein is believed to
be accurate. No responsibility is assumed by AMG for its use.
Page 12 of 12 AMG5914-2A9R Instruction Sheet
D22184-00.doc
Physical Information
Dimensions
Height ................................................ 3U Plug-in
Width ................................................. 14HP
Depth ................................................. 170mm excluding connectors
Weight ............................................... 750grams
Mounting Details
The unit is designed to be mounted within an AMG2009 or AMG2015 Subrack on standard card
guides.
Safety
AMG Optical Fibre Products use Class 1 laser systems in accordance with EN 60825-2:2000.
It is always advisable to follow good practice when working with optical fibre systems. This includes:
§ Do not stare with unprotected eyes or with any unapproved collimating device at fibre
ends or connector faces, or point them at other people.
§ Use only approved filtered or attenuating viewing aids
For other safety issues and advice on good practice associated with optical fibre systems, please see
EN 60825-2:2000 or your local safety officer.
Maintenance and Repair
There are no user serviceable parts within AMG products. See unit data sheet for full specification.
In case of problem or failure, please call your local support centre or contact: AMG Systems Ltd. at
3 The Omega Centre, Stratton Business Park, Biggleswade, Beds., SG18 8QB, UK.
Phone +44 (0) 1767 600 777
Technical Support +44 (0) 1767 604 491
Email techsupport@amgsystems.com
/