Nexa WTE Owner's manual

Brand: Nexa

Model: WTE

Type: Owner's manual

WTE-1 / WTE-2

WALL TRANSMITTER

NEXA AB, DATAVÄGEN 37B, 436 32 ASKIM, SWEDEN

[email protected] | www.nexa.se

ENGLISH

SAFETY AND INFORMATION

Indoor range: up to 30 m (optimal conditions). The range is strongly

dependent on local conditions, such as the presence of metals. For

example, the thin metal coating in Low-emissivity (Low-E) glass has

a negative impact on the range of radio signals.

There may be restrictions on the use of this device outside the EU. If

applicable, check whether this device complies with local directives.

Maximum load: Never connect lights or equipment that exceed

the maximum load of the receiver, as it can result in defects, a short

circuit or ﬁre.

Life-support: Never use Nexa products for life-support systems or

other applications in which equipment malfunctions can have life-

threatening consequences.

Interference: All wireless devices may be subject to interference,

which could affect performance. The minimum distance between 2

receivers should be at least 50 cm.

Repairing: Do not attempt to repair this product. There are no user-

serviceable parts inside.

Water-resistance: This product is not water-resistant. Keep it dry.

Moisture will corrode the inner electronics and can result in a short

circuit, defects and shock hazard.

Cleaning: Use a dry cloth to clean this product. Do not use harsh

chemicals, cleaning solvents, or strong detergents.

Environment: Do not expose the product to excessive heat or cold,

as it can damage or shorten the life of electronic circuit boards.

WTE-1 / WTE-2 is a battery-powered System Nexa wall transmitter

which is compatible with Exxact and Elko Plus & RS switch frames.

They are simple to install on an switch box or on a ﬂat surface with

self-adhesive tape or screw.

The wall transmitter can control System Nexa ON/OFF and dimmer

receiver.

INSTALLATION

1. Open the battery holder on the wall transmitter.

2. Place the battery in the wall transmitter.

3. Fit the back unit on the wall (1a) or switch box (1b).

4. Place wall adapter and transmitter with the marking ”TOP”

upwards in the frame from Schneider Exxact or ELKO (not

included).

5. Screw the wall transmitter on to the back unit.

6. Fit the rocker/rockers on the wall transmitter.

PAIRING

1. Set the receiver to pairing mode – see respective manual.

2. Press the upper part (ON) of the selected rocker within 6 seconds.

PAIRING CONFIRMATION

The LED indicator on the receiver ﬂashes rapidly. If a light is

connected to the receiver, this ﬂashes twice. See also the receiver’s

manual.

DELETING MEMORY

1. Set the receiver to pairing mode – see respective manual.

2. Press the lower part (OFF) of the selected rocker within 6 seconds.

CONFIRMATION DELETION

The LED indicator on the receiver ﬂashes rapidly. If a light is

connected to the receiver, this ﬂashes twice. See also the receiver’s

manual.

OPERATING

ON Press the rocker’s upper part to turn on.

OFF Press the rocker’s lower part to turn off.

DIMMER

Press the rocker’s upper part to turn on. Press brieﬂy on the

rocker’s upper part to start dimming up/down, press brieﬂy again

to stop dimming at desired level.

Battery 1 x 3 V CR2032

Radio protocol System Nexa (433,92 MHz)

Range up to 30 m

Operating temperature 0–45 °C

IP rating IP20 indoor use

Size (W x L x D) 69 x 69 x 16 mm

TEKNISK DATA

Declaration of conformity is available at www.nexa.se

Rocker

Wall transmitter

Screw

Battery

Adapter

Frame

Back unit

1a 2 31b

Nexa WTE Owner's manual

Nexa WTE Owner's manual

Related papers

Other documents