Best P195ES52SB Installation guide

Brand: Best

Model: P195ES52SB

Category: Cooker hoods

Type: Installation guide

This manual is also suitable for

P195ES70SB

Best P195ES52SB is a power module designed for domestic cooking only. It is intended to be installed inside a cabinet with a minimum internal height of 16 inches, and should be mounted centered over the cook top burners. The device comes with a damper, four mounting screws, and a parts bag containing installation instructions. It requires two 13 watt G24q1 Compact Fluorescent lamps, which are included. The Best P195ES52SB has a thermal overload which will automatically shut off the motor if it becomes overheated.

- 1 -

ENGLISH.........................................3

FRANÇAIS......................................11

ESPAÑOL.......................................19

In USA - BEST Hartford, Wisconsin

In CANADA - BEST Drummondville, QC, Canada

For additional Information visit www.BestRangeHoods.com

Power Module

Module de Puissance

Módulo de potencia

Mod. P195ES52SB

Page is loading ...

- 3 -

READ AND SAVE THESE INSTRUCTIONS

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS,

OBSERVE THE FOLLOWING:

1. Use this unit only in the manner intended by the manufacturer. If you have questions,

contact the manufacturer at the address or telephone number listed in the warranty.

2. Before servicing or cleaning unit, switch power off at service panel and lock service

panel to prevent power from being switched on accidentally. When the service

disconnecting means cannot be locked, securely fasten a prominent warning device,

such as a tag, to the service panel.

3. Installation work and electrical wiring must be done by a qualified person(s) in accor-

dance with all applicable codes and standards, including fire-rated construction codes

and standards.

4. Sufficient air is needed for proper combustion and exhausting of gases through the flue

(chimney) of fuel burning equipment to prevent backdrafting. Follow the heating equip-

ment manufacturer’s guidelines and safety standards such as those published by the

National Fire Protection Association (NFPA), and the American Society for Heating,

Refrigeration and Air Conditioning Engineers (ASHRAE), and the local code authorities.

5. When cutting or drilling into wall or ceiling, do not damage electrical wiring and other

hidden utilities.

6. Ducted fans must always be vented to the outdoors.

7. Do not use this unit with any separate solid-state speed control device.

8. To reduce the risk of fire, use only metal ductwork.

9. This unit must be grounded.

INTENDED FOR DOMESTIC COOKING ONLY

- 4 -

CAUTION

1. For indoor use only.

2. To reduce risk of fire and to properly exhaust air, be sure to duct air outside. Do not vent

exhaust air into spaces within walls or ceilings or into attics, crawl spaces, or garages.

3. Take care when using cleaning agents or detergents.

4. Avoid using food products that produce flames under the Range Hood.

5. For general ventilating use only. Do not use to exhaust hazardous or explosive materi-

als and vapors.

6. To avoid motor bearing damage and noisy and/or unbalanced impellers, keep drywall

spray, construction dust, etc. off power unit.

7. Your hood motor has a thermal overload which will automatically shut off the motor if it

becomes overheated. The motor will restart when it cools down. If the motor continues

to shut off and restart, have the hood serviced.

8. For best capture of cooking impurities, the bottom of the hood should be a minimum of

24" and a maximum of 30" above the cooking surface.

9. Use with approved cord-connection kit only.

10. Please read specification label on product for further information and requirements.

WARNING

TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:

A. Never leave surface units unattended at high settings. Boilovers cause smoking and

greasy spillovers that may ignite. Heat oils slowly on low or medium settings.

B. Always turn hood ON when cooking at high heat or when cooking flaming foods. (i.e.

Crepes Suzette, Cherries Jubilee, Peppercorn Beef Flambe’).

C. Clean ventilating fans frequently. Grease should not be allowed to accumulate on fan or

filter.

D. Use proper pan size. Always use cookware appropriate for the size of the surface

element.

TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE TOP

GREASE FIRE, OBSERVE THE FOLLOWING:*

1. SMOTHER FLAMES with a close-fitting lid, cookie sheet, or metal tray, then turn off the

burner. BE CAREFUL TO PREVENT BURNS. If the flames do not go out immediately,

EVACUATE AND CALL THE FIRE DEPARTMENT.

2. NEVER PICK UP A FLAMING PAN - You may be burned.

3. DO NOT USE WATER, including wet dishcloths or towels - violent steam explosion will

result.

4. Use an extinguisher ONLY if:

A. You know you have a Class ABC extinguisher and you already know how to operate

it.

B. The fire is small and contained in the area where it started.

C. The fire department is being called.

D. You can fight the fire with your back to an exit.

* Based on “Kitchen Fire Safety Tips” published by NFPA.

- 5 -

PREPARE THE HOOD

Unpack hood and check contents.

1 - Hood

1 - Parts Bag (B08084044) containing:

4 - Mounting Screws (4,2 x 15mm Pan Head)

1 - 6” Damper

1 - Installation Instructions

DAMPER (B08088378)

4 MOUNTING SCREWS

(4,2 x 15mm Pan Head)

CAUTION

Wear safety gloves before every installation

and/or manitenance operation

- 6 -

AIR

GRILL

6” ROUND

DUCT AND

ELBOW

DUCT

CONNECTOR

HOOD

At least

15”

INSTALL THE DUCTWORK (Ducted Hoods Only) - Fig.1

NOTE: To reduce the risk of fire, use only metal ductwork.

1. Decide where to install the duct.

2. A straight, short duct will allow the hood to perform most efficiently.

3. Long duct, elbows, and transitions will reduce the performance of the hood. Use

as few of them as possible.

4. Use duct tape to seal the joints between ductwork sections.

5. Install a roof or wall cap. Connect 6” round metal ductwork to cap and work back

towards hood location

DUCTED

CONFIGURATION

ROOF CAP

6” ROUND

DUCT

WALL

CAP

HOOD

24” TO 30” ABOVE

COOKING SURFACE

6” ROUND

ELBOW

INSTALL DUCT CONNECTOR

1. Install the damper onto the hood by pressing it onto the discharge opening.

2. Remove the tape located on the damper.

Fig.1

Fig. 2

NON-DUCTED CONFIGURATION

INSTALL THE DUCTWORK (Non-Ducted Hoods Only) - Fig.2

NOTE: The following material must be purchased separately for non-ducted

recirculation installation.

• Non-ducted Charcoal Filter Model:

FILTEREB40

• 6” round metal ductwork and fittings.

• Grill

1. Attach 6” round metal ductwork and fittings.

2. Run ductwork to the location where it is

discharged back into the room.

3. Duct tape all joints to make them secure and

air tight.

4. Install a decorative grill. You may need to

purchase a metal round-to-rectangular

transition, depending on your application.

- 7 -

INSTALL THE HOOD

Note: The hood must be installed inside

the cabinet.

The internal height of cabinet must be

minimum 16”.

The hood should be mounted centered

over the cook top burners.

1. Remove the frame by moving the 2 slide

fasteners “A” forward (Fig.4 ). Push the

filter latch and tilt the filter downward (B)

and remove.

2. Cut a hole in the bottom of the cabinet,

using the dimensions shown (Fig.5 ).

3. Adjust the position of the clasping side

spring by turning the “D” screw

according to the thickness of the

cabinet to which it is going to be

anchored (Fig.6).

4. Insert the hood in the cabinet (Fig.7 ) and

lock in to position using the side spring.

5. Secure the hood with (4) “C” mounting

screws.

6. Replace the frame by moving the 2 slide

fasteners “A” backward. (Fig.4 ).

19-1/2

10-¼”

1”

Fig. 5

X = min 7/16”

max 13/16”

CLASPING SIDE

SPRING

Fig.6

Fig.7

CONNECT DUCTWORK

1. Use 6" round metal duct to connect

the duct connector on the hood to the

ductwork above.

2. Use duct tape to make all joints

secure and air tight.

Fig. 4

HOOD

33-7/16”

(85cm.)

MAX.

WIRING

Note: This range hood must be properly

grounded. The unit should be installed by

a qualified electrician in accordance

with all applicable national and local

electrical codes. The grounded 3 prong

outlet should be accessible after the

hood installation (i.e.: access door).

GROUNDING INSTRUCTIONS

This appliance must be grounded. In the

event of an electical short circuit,

grounding reduces the risk of electric

shock by providing an escape wire for the

electric current. This appliance is equipped

with a cord having a grounding wire with a

grounding plug. The plug must by plugged

into an outlet that is properly installed and

grounded.

WARNING - Improper grounding can

result in a risk of electric shock.

Consult a qualified electrician if the

grounding instructions are not completely

understood, or if doubt exist as to wheter

the appliance is properly grounded. Do not

use an extension cord. If the power supply

cord is too short, have a qualified electrician

install an outlet near the appliance. Position

the power socket at a maximum distance

of 33-7/16” (85cm.) from where the lead

exits from the hood (see illustration

alongside). Fit the plug into the power

socket.

- 8 -

0123

INSTALL FILTERS

(NON-DUCTED HOODS ONLY - Fig.8 )

1. Install a charcoal filter on each side of

the blower (included with Non-ducted

Charcoal Filter Model: FILTEREB40

2. To install the charcoal filter, align center

keyhole slot on the filter with center of

the blower. Rotate to lock filter into place.

3. To remove the charcoal filter, rotate the

filter until it disengages from the blower.

(DUCTED AND NON-DUCTED HOODS)

• To remove the GREASE filter, grip the

latch tab and pull it down. This will

disengange the filter from the hood.

• To install the GREASE filter, align filter

tabs to the side of the filter with slots in

the hood drawer. Pull latch tab down,

push filter up into place and release the

tab.

• Make sure the filter is securely

enganged after assembly.

Fig.8

NON-DUCTED

RECIRCULATION FILTERS

MAINTENANCE

ALWAYS SWITCH OFF THE ELECTRICITY

SUPPLY BEFORE CARRYING OUT ANY

OPERATIONS ON THE APPLIANCE.

Grease Filters

The grease filter should be cleaned fre-

quently. Use a warm detergent solution.

Grease filter is dishwasher safe.

To remove the grease filter: push in on the

metal latch tab. Tilt the filter downward and

remove.

Cleaning

Occasional care will help preserve its fine

appearance.

• Clean with warm water and mild detergent

only.

• Follow all cleaning by rinsing with clear

water.

• Wipe dry with clean, soft cloth.

Light bulbs - (Fig.9)

This range hood requires two 13 watt G24q-

1 Compact Fluorescent lamps (included).

To change bulbs:

1. Remove the frame by moving the 2 slide

fasteners (A) (Fig.4, page 6).

2. To replace lamp, grasp lamp at

base and pull out to remove. Replace

with 13W Fluorescent lamp noted

above.

CAUTION: BULB MAY BE HOT!

Fig.9

OPERATION - Fig.10

Controls

The light switch turns the lamps on and

off.

The blower switch: makes it possible

to select the motor operating speed (3

speeds).

Position 0: motor off.

The pilot lamp lights up whenever the

blower is on.

LIGHT

SWITCH

BLOWER

SWITCH

PILOT LAMP

Fig.10

- 9 -

WARRANTY

ONE YEAR LIMITED WARRANTY FOR BEST PRODUCTS

Broan-NuTone LLC (Broan-NuTone) warrants to the original consumer purchaser of

Best products that such products will be free from defects in materials or workmanship

for a period of one year from the date of original purchase. THERE ARE NO OTHER

WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO,

IMPLIED WARRANTIES OR MERCHANT ABILITY OR FITNESS FOR A

PARTICULAR PURPOSE.

During this one-year period, Broan-NuTone will, at its option, repair or replace, without

charge, any product or part which is found to be defective under normal use and

service.

THIS WARRANTY DOES NOT EXTEND TO FLUORESCENT LAMP STARTERS,

TUBES, HALOGEN AND INCANDESCENT BULBS, FUSE, FILTERS, DUCTS, ROOF

CAPS, WALL CAPS AND OTHER ACCESSORIES FOR DUCTING. This warranty

does not cover (a) normal maintenance and service or (b) any products or parts

which have been subject to misuse, negligence, accident, improper maintenance or

repair (other than by Broan-NuTone), faulty installation or installation contrary to

recommended installation instructions.

The duration of any implied warranty is limited to the one-year period as specified for

the express warranty. Some states do not allow limitation on how long an implied

warranty lasts, so the above limitation may not apply to you.

BROAN-NUTONE'S OBLIGATION TO REPAIR OR REPLACE, AT BROAN-

NUTONE'S OPTION, SHALL BE THE PURCHASER'S SOLE AND EXCLUSIVE

REMEDY UNDER THIS WARRANTY. BROAN-NUTONE SHALL NOT BE LIABLE

FOR INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES ARISING OUT

OF OR IN CONNECTION WITH PRODUCT USE OR PERFORMANCE. Some states

do not allow the exclusion or limitation of incidental or consequential damages, so the

above limitation or exclusion may not apply to you.

This warranty gives you specific legal rights, and you may also have other rights,

which vary from state to state. This warranty supersedes all prior warranties.

To qualify for warranty service, you must (a) notify Broan-NuTone at the address

stated below or telephone number stated below, (b) give the model number and part

identification and (c) describe the nature of any defect in the product or part. At the

time of requesting warranty service, you must present evidence of the original

purchase date.

In USA - Best®, 926 W. State Street, Hartford, WI 53027 (800-558-1711)

In Canada - Best®, 550 Lemire Blvd., Drummondville, QC J2C 7W9

(866-737-7770)

www.BestRangeHoods.com

HEAT SENTRY™

Your hood is equipped with a HEAT SENTRY™ thermostat. This thermostat is a

device that will turn on or speed up the blower if it senses excessive heat above the

cooking surface.

1) If blower is OFF - it turns blower ON to HIGH speed.

2) If blower is ON at a lower speed setting - it turns blower up to HIGH speed.

When the temperature level drops to normal, the blower will return to its original

setting.

WARNING

The HEAT SENTRY thermostat can start the blower even if the hood is turned

OFF. When this occurs, it is impossible to turn the blower OFF with its switch. If

you must stop the blower, do it from the main electrical panel.

- 10 -

SERVICE PARTS

B08093943

B03295083

B02011013

B08087694

B02300985

B02320351

B03293051

B02300787

B03294033

B02300983

B08088378

B03202287

B03290499

B03295084

B032920170

B032920180

BR2300132

B032920200

B03294781

B08086668

B02300987

B02320352

B08080375

B03201014

B03295075

B03295072

B03295074

B03295073

B08084044

B06002195

B06108783

FRAME

SIDE FASTENER

SPRING

GREASE FILTER

CAPACITOR

FLUORESCENT LAMP

LIGHT LENS

HEAT SENTRY

ELECTRICAL PRINTED CIRCUIT BOARD BOX COVER

POWER CORD

DAMPER

CABLE STOP

WIRE GUIDE

GRID LATCH

WIRING BOX

WIRING BOX COVER

JUNCTION CLAMP

ELECTRICAL BOX WIRE CLAMP

ELECTRICAL PRINTED CIRCUIT BOARD BOX

ELECTRICAL PRINTED CIRCUIT BOARD

FLUORESCENT LAMP HOLDER

FLUORESCENT BALLAST

SWITCH MOUNTING BOARD

PILOT LAMP

SWITCH BOARD BOX COVER

SWITCH BOARD BOX

MOTOR SWITCH

LIGHT SWITCH

PARTS BAG

BLOWER ASSEMBLY (Included Key No. 45, 48, 49, 53)

SWITCH BOX ASSEMBLY (Included Key No. 228, 229,

230, 234, 238, 241)

107

114

134

145

146

147

151

165

166

197

208

228

229

230

234

238

241

998

CAS

AQI

KEY No. PART No. DESCRIPTION

Page is loading ...

- 18 -

LISTE DES PIÈCES DE RECHANGE

B08093943

B03295083

B02011013

B08087694

B02300985

B02320351

B03293051

B02300787

B03294033

B02300983

B08088378

B03202287

B03290499

B03295084

B032920170

B032920180

BR2300132

B032920200

B03294781

B08086668

B02300987

B02320352

B08080375

B03201014

B03295075

B03295072

B03295074

B03295073

B08084044

B06002195

B06108783

ENCADREMENT

ARRET DE GRILLE

RESSORT

FILTRE Á GRAISSE

CONDENSATEUR

TUBE AU NEON

PLAFFONIERE

HEAT SENTRY

COUVERCLE BOITE CIRCUIT IMPRIME ELECTRIQUE

CABLE ALIMENTATION

BRIDE DE RACCORDEMENT

ARRET CABLE

SERRE CABLE

CROCHET

BOITE CABLE ALIMENTATION

COUVERCLE BOITE CABLE ALIMENTATION

BORNE

SERRE CABLE BOITE INSTALLATION ELECTRIQUE

BOITE INSTALLATION ELECTRIQUE

CIRCUIT IMPRIME ELECTRIQUE

SUPPORT NEON

RÉGULATEUR DE COURANT

CIRCUITE IMPRIME COMMANDES

LAMPE TEMOIN

COUVERCLE TABLEAU DE COMMANDES

BOITE TABLEAU DE COMMANDES

BOUTON MOTEUR

BOUTON LUMIERE

ACCESSOIRE DE FIXATION

ENSEMBLE CONVOYER (Comprend les repères n°. 45,

48, 49, 53)

ENSEMBLE TABLEAU DE COMMANDES (Comprend les

repères n°. 228, 229, 230, 234, 238, 241)

107

114

134

145

146

147

151

165

166

197

208

228

229

230

234

238

241

998

CAS

AQI

N°

REPÈRE

DESCRIPTION

N° DE

PIÈCE

Page is loading ...

- 26 -

LISTA DE PIEZAS DE RECAMBIO

B08093943

B03295083

B02011013

B08087694

B02300985

B02320351

B03293051

B02300787

B03294033

B02300983

B08088378

B03202287

B03290499

B03295084

B032920170

B032920180

BR2300132

B032920200

B03294781

B08086668

B02300987

B02320352

B08080375

B03201014

B03295075

B03295072

B03295074

B03295073

B08084044

B06002195

B06108783

MARCO

CIERRE LATERAL

MUELLE

FILTRO ANTI-GRASA

CONDENSADOR

LÁMPARA FLUORESCENTE

LENTE LUZ

SENSOR DE TEMPERATURA

TAPA DE LA CAJA BASE DE INSTALACIÓN ELÉCTRICA

CABLE DE ALIMENTACIÓN

CONEXIÓN DE SALIDA DE AIRE

TOPE DE CABLES

ALAMBRE GUÍE

CIERRE DE LA REJILLA

CAJA ELÉCTRICA

CUBIERTA DE LA CAJA

TERMINAL

CAJA ELÉCTRICA ABRAZADERA DE CABLE

CAJA ELÉCTRICA

TABLERO DE CIRCUITO IMPRESOS

SOPORTE DE LÁMPARA FLUORESCENTE

REGOLADOR DE CORRIENTE

TABLERO DE CIRCUITO IMPRESOS DE MANDOS

PILOTO

CUBIERTA DE LA CAJA DE INTERRUPTORES

CAJA DE INTERRUPTORES

INTERRUPTOR DEL MOTOR

INTERRUPTOR DE LA LUZ

JUEGO DE PIEZAS

CONJUNTO DEL VENTILADOR (Incluye las clave N° 45,

48, 49, 53)

CONJUNTO DE LA CAJA DE INTERRUPTORES (Incluye

las clave N° 228, 229, 230, 234, 238, 241)

107

114

134

145

146

147

151

165

166

197

208

228

229

230

234

238

241

998

CAS

AQI

CLAVE N° PIEZA N° DESCRIPCIÓN

Page is loading ...

Best P195ES52SB Installation guide

Brand: Best

Model: P195ES52SB

Category: Cooker hoods

Type: Installation guide

This manual is also suitable for

P195ES70SB

Download PDF

report

in other languages

français: Best P195ES52SB Guide d'installation
español: Best P195ES52SB Guía de instalación

Best P195ES52SB Installation guide

This manual is also suitable for

Best P195ES52SB Installation guide

in other languages

Related papers

Other documents