Panasonic PVC2024 Operating instructions

Panasonic
Brand
Panasonic
Model
PVC2024
Category
Cassette players
Type
Operating instructions

This manual is also suitable for

-1 2-
1) Presione Ź.
2) Para ajustar la FECHA de grabación,
presione Ÿź para seleccionar:
• 1 - 31 = Grabación única
• DIARIO = a la misma hora de lunes a viernes
• SEMANAL = a la misma hora una vez a la
semana
3) Para los ajustes siguientes, presioneŸź
para seleccionar y presione Ź para
ajustar los tiempos de INICIO/ PARADA,
CANAL, o entrada de LINEA, y velocidad
del casete.
Operaciones básicas para la
reproducción
■ Para encontrar una escena en
particular
Búsqueda hacia adelante Ö Presione FF
Búsqueda hacia atrás Ö Presione REW
• Después de comenzar la búsqueda, cada vez
que presione FF o REW cambiará la velocidad.
■ Para ver una imagen ¿ja (congelada)
Ö Presione PAUSE/SLOW
■ Para ver en cámara lenta
Ö Mantenga pulsado el botón
PAUSE/SLOW en el modo de imagen ¿ja
■ Para ver imágenes cuadro a
cuadro
Ö Presione PAUSE/SLOW en el modo de
imagen ¿ja
■ Para parar
Ö Presione STOP
■ Para rebobinar la cinta
Ö Presione REW
■ Para hacer avanzar la cinta
rápidamente
Ö Presione FF
■ Para expulsar la cinta
Ö Presione EJECT en el con trol remoto o
STOP/EJECT en el
videograbador
combinado
Operaciones básicas para la
grabación
Grabación con temporizador
Fecha de hoy
■ El videograbador combinado deja de
grabar a una hora pre¿jada.
(Grabación de un toque)
Presione REC repetidamente para ajustar la
duración de la grabación como sigue:
como sigue: 30 min. Ö 1 hr Ö 1:30 Ö 2:00 Ö
3:00 Ö 4:00 Ö Salida
Inserte un casete.
• El videograbador combinado se enciende
automáticamente.
1
Presione PLAY.
• La reproducción comienza automáticamente si
el casete no tiene la lengüeta para prevención
de grabación.
2
Inserte el casete con lengüeta de
protección de grabación.
• El videograbador combinado se enciende
automáticamente.
1
Presione CH Ÿź, o las teclas de
numéros para seleccionar el canal.
2
Presione SPEED para seleccionar la
velocidad de grabación.
SP = reproducción normal
SLP = reproducción super larga
• La velocidad seleccionada debe aparecer en la
pantalla.
3
Presione REC para comenzar a
grabar.
• Para editar partes no deseadas de una
grabación, presione PAUSE/SLOW para hacer
una pausa durante la grabación.
4
Presione PROG para visualizar la
pantalla FIJAR PROGRAMACION.
1
Presione Ÿź para seleccionar
TEMPORIZADOR.
2
FIJAR PROGRAMACION
TEMPORIZADOR
ENCENDIDO AUTOMATICO
ELEGIR : FIJAR:
TERMINAR:PROG
4
P FE INIC PARADA CA VEL
1 -- --:-- --:-- -- --
2 -- --:-- --:-- -- --
3 -- --:-- --:-- -- --
4 -- --:-- --:-- -- --
ELEGIR : FIJAR:
TERMINAR:PROG
Presione PROG para ¿nalizar el
programa.
Para introducir más programas.
presione Ÿź y Ź para seleccionar y
ajustar el número de programa en
blanco, y luego repita el paso 4.
5
P FE INIC PARADA CA VEL
1 10 9:00a12:00p 08 SP
2 -- --:-- --:-- -- --
3 -- --:-- --:-- -- --
4 -- --:-- --:-- -- --
FIJACION ES COMPLETO
CANCELAR:ADD/DLT
ELEGIR : FIJAR:
TERMINAR:PROG
Salga de este modo. Presione
PROG dos veces.
• Si está usando un decodi¿cador de TV cable,
asegúrese que se encuentra en el canal
deseado y que la alimentación queda
conectada para grabar con temporizador.
• El indicador PROG TIMER se enciende en el
videograbador combinado.
6
Presione STOP para detener la
grabación.
5
Presione Ź para visualizar la
pantalla.
3
Spanish Quick Use Guide/Guía para rápida consulta
Spanish Quick Use Guide/Guía para rápida consulta
-1 1-
Si el ajuste automático del reloj no se ha
completado, ajuste el reloj manualmente de la
siguiente manera:
Ajustar de nuevo el reloj
Ajuste manual del reloj
Conectando
Realizando Con¿guracion Inicial
Para Ant./Cable
Conecte Ant./Cable a la entrada de antena de la
TV (VHF/UHF).
Para Sistema Digital de Satelite (DSS)/Convertidor
de cable
Conecte la salida del convertidor de cable la
“VHF/UHF” con el RF cable.
CH AUTO SET PROCEEDING
AUTO CLOCK SET
PROCEEDING
CANCEL:STOP
1/ 4/2004 SUN 12:00PM
DST:ON
SETTING : CH
AUTO CLOCK SET
COMPLETED
AUTO CLOCK SET
IS INCOMPLETE
PLEASE SET CLOCK BY
PRESSING ACTION KEY
Presione la tecla ACTION en el control
remoto para visualizar la pantalla del
menú SET CLOCK (FIJAR RELOJ).
1
Presione Ÿź para seleccionar el mes
y Ź para ajustar. De la misma forma,
seleccione y ajuste la fecha, año, hora
y DST (Hora de Verano).
2
Presione dos veces la tecla ACTION
para poner el RELOJ en marcha y salir.
3
Presione ACTION para exhibir el menú.
1
Presione ŸźŻ Ź para seleccionar
“RELOJ,” y luego presione ACTION.
2
Presione Ÿź para seleccionar
“MANUAL” y luego presione .
3
Presione Ÿź y ŻŹ para seleccionar y
ajustar la hora y la fecha.
4
Presione ACTION dos veces para que
el reloj comience a funcionar y salir
desde este modo.
5
Si “AUTO CLOCK SET IS INCOMPLETE”
aparece en pantalla, coloque el tiempo usando
el procedimiento manual (MANUAL CLOCK
SET), usa un convertidor.
MENU PRINCIPAL
TV BLOQUEO IDIOMA
CANAL RELOJ SALIR
ELEGIR:
FIJAR :ACTION
FIJAR RELOJ
FIJACION AUTOMATICA
MANUAL
AJUSTE ZONA HORA : 0
ELEGIR : FIJAR:
TERMINAR:ACTION
FIJAR RELOJ
1/ 4/2004 DOM 12:00AM
VERANO:ACT
-----------------------
ELEGIR : FIJAR:
INICIAR :ACTION
Spanish Quick Use Guide/Guía para rápida consulta
Apretar demasiado los cables coaxiales RF
“tipo tuerca” podría dañar los conectores.
Asegúrelos solamente con los dedos.
PRECAUCIÓN
Realice todas las conexiones de cables o
antena antes de encenderlo.
Nota:
• Los botones de funciones no funcionarán durante la
con¿guración inicial.
• Para retirar un casete durante el ajuste automático,
presione EJECT en el control remoto. Luego ajuste
manualmente. (Vea la p.10 de Libro de operaciones
avanzadas).
• Dependiendo de las condiciones, el ajuste automático
de reloj podría llevar más de 30 minutos. En tal caso,
presione STOP para detener la con¿guración y realizar
los ajustes manualmente. (Vea la p.10 de Libro de
operaciones avanzadas).
Enchufe el cable de alimentación en el
tomacorrientes de CA de la pared.
• Si usa un convertidor de
cable, enciéndalo y
ajústelo al canal Public
Broadcasting Service
(PBS) de su zona horaria.
Si usa un receptor DSS
(Sistema digital de
satélite), éste deberá estar
apagado.
Los ajustes se realizarán
automáticamente. Cuando termine,
aparecerá esta pantalla.
Presione POWER en el control remoto
o la unidad. Comenzará el ajuste
automático de canales y del reloj.
1
2
3
SET CLOCK
1/ 1/2004 THU 12:00AM
DST:ON
-----------------------
SELECT: SET:
START :ACTION
SET CLOCK
1/ 4/2004 SUN 12:00AM
DST:ON
-----------------------
SELECT: SET:
START :ACTION
Please read these instructions carefully before attempting to connect,
operate, or adjust this product. Please save this manual.
Spanish Quick Use Guide is included.
(Guía para rápida consulta en español está incluida.)
Models No. PV-C1324/PV-C1334W/
PV-C2024
LSQT0767 A
As an
E
NERGY
S
TAR
®
Partner,
Matsushita Electric Corporation of Amer ica has de termined
that this prod uct or product mod el meets the
E
NERGY
S
TAR
®
guidelines for en ergy ef ¿ciency.
Combination VCR
Operating Instructions
(Basic Operations)
For advanced operations, see the separate
“Advanced Operations” instruction book.
For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at: http://www.panasonic.com/contactinfo
This operating instruction book is designed for use with models
PV-C1324, PV-C1334W and PV-C2024. Illustrations in this manual
show the PV-C2024.
Table of Contents
IMPORTANT SAFEGUARDS AND PRE CAU TIONS........................................2
Safety Precautions/Mesures de sécurité ..........................................................3
Customer Services Directory ............................................................................3
Before Using......................................................................................................4
Connections/Initial Setup (Ready to Play).........................................................5
Basic Operation (Unit) .......................................................................................6
Basic Operation (Tape)......................................................................................7
Limited Warranty ...............................................................................................8
Location of Controls ..........................................................................................9
Importantes Precauciones de Seguridad ........................................................10
Spanish Quick Use Guide/Guía para rápida consulta............................... 11, 12
-10-
1 Precauciones para los recursos de energía
Opérelo solamente usando la fuente de energía
indicada en el aparato o en este manual. Si tiene
dudas haga que su compañía de utilidades eléctricas
o a su distribuidor que veri¿quen las fuentes de
energía de su casa.
2 Enchufar el cordón de energía
Para la seguridad de este aparato, este posee una
clavija de tipo polarizado (una clavija ancha) o una
clavija de tres patas. Siempre mantenga el enchufe
¿rmemente y asegurase de que tenga las manos
secas cuando conecte o desconecte el enchufe del
cordón de energía. Limpie el polvo y la tierra del
enchufe regularmente.
PRECAUCIONES PARA EL ENCHUFE
POLARIZADO:
La clavija queda en el enchufe de una manera
solamente, si esta no entra trate de revertirla y si aun
no le es posible conectarla llame a un electricista
para que le instale un enchufe apropiado. No trate de
ajustar la clavija.
PRECAUCIÓN CON ENCHUFES CON TOMA A
TIERRA:
Este enchufe sólo entrará en una toma con conexión a
tierra de tres ori¿cios. Si fuera necesario, que un técnico
electricista le instale la toma de red adecuada. No
desactive esta función de seguridad manipulando el
enchufe de ninguna manera.
3 CORDON DE ENERGIA
Para evitar un mal funcionamiento del aparato y para
protegerse de un corto circuito, fuego o un daño
personal.
- Mantenga el cordón de energía alejado de los aparatos
que generen calor y de los espacios por donde se
camine. No coloque objetos pesados o cosas rodando
sobre el cordón de energía.
- No ajuste el cordón de ninguna manera.
- Si se usa una extensión de cordón, esta debe tener el
mismo tipo de clavija y estar seguramente conectado.
- Los enchufes sobrecargados o los cordones de
extensión, pueden causar incendios.
- Cordones dañados cortados o cables craqueados
pueden causar incendios y deben ser remplazados por
un electricista cali¿cado.
4 NO BLOQUEE LAS ABERTURAS DE
VENTILACION
Las aberturas de ventilación en el gabinete dejan
escapar el calor que es generado durante el
funcionamiento. Si estos son obstruidos el calor se
acumula, lo que puede resultar en un incendio o
daños a casetes o a discos.
Para su protección:
a. Nunca cubra las aberturas de ventilación mientras el
aparato este ENCENDIDO, no ponga el aparato a
funcionar sobre la cama, el sillón, el tapete, o alguna
super¿cie blanda.
b. Evite la instalación incorporada, como en una biblioteca
o estantería, a menos que esté correctamente ventilada.
5 EVITE LUGARES EXTREMADAMENTE
CALIENTES O CAMBIOS BRUSCOS DE
TEMPERATURA
No coloque el aparato sobre o junto a un aparato de
calefacción, radiador o lo exponga a los rayos
solares, o dentro de un vehículo cerrado, en altas
temperaturas de más de 95 ºF (35 ºC), o 75 % de
humedad. Si el aparato es cambiado bruscamente de
una temperatura fría a caliente la humedad se puede
condensar dentro del aparato y causar daños a las
cintas. Nunca exponga el aparato a vibraciones,
impactos o lo coloque en una super¿cie desnivelada
porque puede causar serios daños a las partes
interiores.
6 Para evitar daños personales
• Nunca coloque el aparato en alguna super¿cie
insegura, mantenga el aparato sobre una super¿cie
segura, nivelada y fuerte. De otra manera el aparato
podría caer causando daños a algún niño, adulto y
dañar el aparato.
• Mueva cualquier aparato con cuidado y usando una
mesa rodante. Las paradas rápidas,
exceso de fuerza, o las super¿cies
desniveladas pueden causar que los
objetos volteen.
• Siga cuidadosamente todas las
instrucciones de funcionamiento.
1 SEGURIDAD PARA LA INSTALACION DE LA ANTENA Y EL CABLE
Un sistema de antena o cable instalado afuera debe de estar apropiadamente
incrustado en la tierra para proveer algo de protección contra la estática y las
cargas de voltaje. La Sección 810 de el código nacional de electricidad ANSI
/ NFPA 70 (en Canadá parte 1 del código de electricidad de Canadá) que
provee con información acerca de la manera apropiada para poner tierra en
el mástil y asegurar la estructura, la
entrada del alambre a la tierra y
dirigirlo a una unidad de descarga
de la antena, tamaño de los
conductores de tierra, la ubicación
de la unidad de descarga de la
antena, conexiones de los
electrodos, y los requerimientos
para los electrodos de tierra.
2 MANTENGA LA ANTENA ALEJADA DE LOS CABLES Y CIRCUITOS
DE ALTO VOLTAJE.
Sitúe el sistema de antena de afuera alejado de las líneas eléctricas o
circuitos de energía para en caso de caerse este no toque las líneas de
energía eléctrica. Cuando instale la antena nunca toque los cables de
energía eléctrica, los circuitos eléctricos u otros recursos de energía.
EMPALMADOR
DE CONEXIÓN
A TIERRA
EQUIPO DE
SERVICIO
ELÉCTRICO
BAJADA DE ANTENA
UNIDAD DE DESCARGA
DELA ANTENA (SECCIÓN
S10-20 DEL NEC)
CONDUCTORES CONEXIÓN
A TIERRA (SECCIÓN
S10-20 DEL NEC)
SISTEMA DE ELECTRODOS DE
CONEXIÓN A TIERRA DEL SERVICIO
ELÉCTRICO (ART, 250 DEL NEC, PARTE H)
CÓDIGOO ELÉCTRICO
NEC-NATIONAL
EMPALMADOR DE
CONEXIÓN A TIERRA
PRECAUCION: PARA EVITAR LA POSIBILIDAD DE
UNA DESCARGA ELECTRICA NO DESMONTAR LA
CUBIERTA (O LA PARTE TRASERA). ESTE APARATO
NO PUEDE SER REPARADO POR EL PROPIETARIO.
PARA CUALQUIER TRABAJO DE SERVICIO SE
DEBE RECURRIR A UN TECNICO ESPECIALIZADO.
PELIGRO DE DESCARGA
ELECTRICA NO ABRIR
PRECAUCION
Precauciones de seguridad
ADVERTENCIA
PARA REDUCIR EL RIESGO DE GOLPES ELÉCTRICOS, INCENDIOS, HERIDAS O DAÑOS A ESTE
PRODUCTO, LEA Y GUARDE TODAS LAS INSTRUCCIONES DE SEGURIDAD Y FUNCIONAMIENTO.
TENGA EN CUENTA TODAS LAS ADVERTENCIAS INDICADAS EN EL MANUAL Y EN EL PRODUCTO.
ADVERTENCIA
PRECAUCIÓN
INSTALACION PARA LA ANTENA AFUERA
USANDO EL APARATO
Instalación
SERVICIOS
1 NO ARREGLE EL PRODUCTO USTED MISMO
Si, después de seguir las instrucciones cuidadosa y
detalladamente el aparato no funciona adecuadamente, no
trate de abrir ni quitar las cubiertas, o hacer ningunos ajustes
que no se encuentren descritos en el manual. Desconecte el
aparato y comuníquese con un técnico cali¿cado.
2 REEMPLAZO DE PARTES
Asegurase que el técnico de servicios use solamente partes
de manufactura o que tengan las características originales de
manufactura, el uso o substituto de partes inautorizadas
puede resultar en fuego, choques eléctricos o otros daños.
3 REVISION DE SEGURIDAD DESPUES DEL SERVICIO
Después de darle servicio o reparar el aparato solicite una
revisión cuidadosa de acuerdo como lo describe en las
escrituras de servicio de los fabricantes para asegurar que el
aparato este seguro y en condiciones operables.
Antes de sacar el aparato del almacén, o moverlo de lugar,
consulte de nuevo esta sección referente a la seguridad.
1 Mantenga el aparato alejado del agua o la humedad,
como Àoreros, lavabos, tinas, etc.
2 Si es expuesto a la lluvia la humedad, o a un impacto
fuerte, desconecte el aparato y deje que lo examine un
inspector técnico cali¿cado antes de usarlo.
3 Tormenta eléctrica
Durante una tormenta eléctrica, o antes de dejar el aparato
sin usar por un período largo de tiempo desconecte todo el
equipo de la energía eléctrica así como también la antena y el
sistema de cable.
4 CUANDO EL APARATO ESTE CONECTADO
• NO LO PONGA A FUNCIONAR SI:
- Ha caído líquido dentro del aparato.
- El aparato se cayó o se dañó de alguna otra manera.
- Si el aparato soltó humo, algún olor o hizo ruido, inmediatamente
desconecte el aparato, y haga que lo revise un técnico de
servicio para evitar las probabilidades de fuego y daños de
cortocircuitos.
• Nunca tire o empuje ningún objeto en la abertura del aparato.
Tocar las partes internas del aparato puede causar cortocircuito
o incendios. No coloque ningún objeto extraño en charola.
• Mantenga objetos magnéticos, tales como bocinas lejos del
aparato para evitar interferencia eléctrica.
5 USO DE ACCESORIOS
Use solamente objetos recomendados por los fabricantes
para evadir los riesgos de fuego, electrochoques u otros
daños.
6 PARA LIMPIAR EL APARATO
Desconecte el aparato. Use un trapo limpio y sin ningún
producto químico para limpiar el polvo suavemente. NO USE
químicos líquidos o aerosol, o aire forzado que se pueda
expandir, o deslizarse dentro del aparato y causar un choque
eléctrico. Cualquier substancia o cinta adhesiva, etc. pueden
marcar la super¿cie del gabinete. La exposición a la grasa, la
humedad o áreas con polvo pueden causar daños en las
partes internas del aparato.
Este símbolo es una advertencia para el usuario de que el voltaje dentro del aparato podría
contener la su¿ciente magnitud para causar choques eléctricos. Por eso es peligroso el tratar
de hacer cualquier clase de contacto con cualquier parte de adentro de este aparato.
Este símbolo es una advertencia de la literatura importante concerniente al funcionamiento y
mantenimiento de este aparato que ha sido incluida. Por lo tanto es de suma importancia que
esta sea leída cuidadosamente para poder evitar cualquier problema.
PARA PREVENIR INCENDIOS O CHOQUES ELÉCTRICOS NO EXPONGA
ESTE APARATO A LA LLUVIA O LA HUMEDAD.
PARA PREVENIR CHOQUES ELÉCTRICOS, ASEGURASE QUE LA CLAVIJA
HAGA JUEGO CON EL ENCHUFE Y CONÉCTELO COMPLETAMENTE.
IMPORTANTES PRECAUCIONES DE SEGURIDAD
Limited Warranty Remote Control Buttons Front View of the Unit and Indicators Rear View of the Unit Importantes Precauciones de
Seguridad
-9-
Remote Control Buttons
Front View of the Unit and Indicators
9,'(2,1 $8',2,1
32:(5 92/ &+
6723(-(&7 5(:
3/$<5(3($7
)) 5(& ,1387
$&7,21
5(& 217,0(5
352*7,0(5
Rear View of the Unit
VHF/UHF
1
AC Power Plug
When plugged into an AC outlet, the unit consumes 2.5 W of electric power in
OFF condition.
2
VHF/UHF Antenna Input Terminal In from your Antenna or Cable.
1
Built-In Speaker
Equipped with 2 front
speakers.
2
AUDIO/VIDEO IN Jack For dubbing.
3
POWER Turns unit on or off.
4
VOLUME UP/DOWN Adjusts volume.
SET/BACK SPACE
Sets a selected menu, or
goes back to correct.
5
CHANNEL UP/DOWN Selects a channel.
TRACKING
UP/DOWN
Reduces picture noise during
Playback and Slow Motion.
SELECT UP/DOWN
Controls navigation around
on-screen menu.
6
STOP Stops recording or playback.
EJECT Ejects tape.
ACTION Press together with REW.
7
REWIND/SEARCH
Rewinds tape, and searches
previous scene.
ACTION Press together with STOP.
8
PLAY Begins playback.
REPEAT Repeats a recording.
9
FAST FORWARD/
SEARCH
Fast forwards tape, and
searches next scene.
10
REC Records the program.
11
INPUT Selects LINE input.
12
Remote Sensor
Receives infrared signal from
remote control.
13
REC Indicator Lights during recording.
14
ON TIMER Indicator
Lights when the On-Timer is
set.
15
PROG TIMER
Indicator
Lights when the unit is set for
Timer Recording.
16
PHONES Jack
Connect an earphone or
headphones.
1
2345678910111213141516
12
1
2
3
4
5
6
7
8
9
10
11
12
13
25 24
23
22
21
20
19
18
17
16
15
14
26
1
POWER Turns unit on or off.
2
DISPLAY Displays VCR status and clock.
3
TAPE POSITION Locates tape position and amount of tape remaining.
4
COUNTER RESET Resets to “0:00:00.”
5
RAPID TUNE Displays the last channel you were watching.
6
MUTE Mutes the sound instantly.
7
CHANNEL UP/DOWN Selects a channel.
SELECT UP/DOWN Controls navigation around on-screen menu.
8
ACTION Displays Main Menu.
9
STOP Stops recording or playback.
10
REWIND/SEARCH Rewinds tape, and searches previous scene.
11
PAUSE/SLOW Pauses and slow motion and frame advance picture.
12
REC Records the program.
13
INPUT Selects LINE input.
14
SPEED Selects recording speed.
15
CM SKIP/ZERO
SEARCH
In Stop mode, goes to the counter “0:00:00.” In Play
mode, skips over 1 to 3 minutes of tape.
16
FAST
FORWARD/SEARCH
Fast forwards tape, and searches next scene.
17
PLAY Begins playback.
18
PROGRAM
Displays SET PROGRAM screen. You can set Timer
Program and On-Timer.
19
VOLUME UP/DOWN Adjusts volume.
SET/BACK SPACE Sets a selected menu, or goes back to correct.
20
SEARCH
Goes directly to the desired recording. Locates end
point of recording.
21
ADD/DELETE Adds or deletes a channel.
22
NUMBER Keys Selects channel directly.
23
TRACKING UP/DOWN Reduces picture noise during Play and Slow.
24
SLEEP Turns off the unit automatically.
25
NIGHT
Color and picture intensity level are adjusted for night
time use.
26
EJECT Ejects tape. Eject is not available during recording.
Location of Controls
-8-
Panasonic Consumer Electronics Company,
Division of Matsushita Electric Corporation of America
One Panasonic Way Secaucus,
New Jersey 07094
Panasonic Sales Company (“PSC”),
Division of Matsushita Electric of Puerto Rico, Inc.
Ave. 65 de Infanteria. Km. 9.5
San Gabriel Industrial Park, Carolina, Puerto Rico 00985
Printed in Indonesia
LSQT0767 A
S0104-0
P
PANASONIC CONSUMER ELECTRONICS
COMPANY, DIVISION OF MATSUSHITA
ELECTRIC CORPORATION OF AMERICA
One Panasonic Way Secaucus, New Jersey 07094
PANASONIC SALES COMPANY, DIVISION OF
MATSUSHITA ELECTRIC OF PUERTO RICO,
INC.,
AVE. 65 de Infantería, Km. 9.5 San Gabriel
Industrial Park, Carolina, Puerto Rico 00985
Panasonic/Quasar Video Products
Limited Warranty
Limited Warranty Coverage
If your product does not work properly because of a defect in materials or workmanship, Panasonic
Consumer Electronics Company or Panasonic Sales Company (collectively referred to as “the warrantor”)
will, for the length of the period indicated on the chart below, which starts with the date of original purchase
(“warranty period”), at its option either (a) repair your product with new or refurbished parts, or (b) replace it
with a new or a refurbished product. The decision to repair or replace will be made by the warrantor.
During the “Labor” warranty period there will be no charge for labor. During the “Parts” warranty period,
there will be no charge for parts. You must carry-in or mail-in your product or arrange for in-home service,
as applicable, during the warranty period.
If non-rechargeable batteries are included, they are not warranted. This warranty only ap plies to products
purchased and serviced in the United States or Puer to Rico. This warranty is extended only to the original
purchaser of a new product which was not sold “as is.” A purchase receipt or other proof of the original
purchase date is required for warranty service.
Carry-In, Mail-in or In-Home Service
For Carry-In, Mail-In or In-Home Service (as applicable) in the United States call toll free contact number
listed above or visit Panasonic Web Site: http://www.panasonic.com
For assistance in Puerto Rico call Panasonic Sales Company (787)-750-4300 or fax (787)-768-2910.
In-Home service, if applicable, requires clear, complete and easy access to the product by the authorized
servicer and does not include removal or re-installation of an installed product. It is possible that certain
in-home repairs will not be completed in-home, but will require that the product, or parts of the product, be
removed for shop diagnosis and/or repair and then re turned.
Limited Warranty Limits And Exclusions
This warranty ONLY COVERS failures due to defects in materials or workmanship, and DOES NOT
COVER normal wear and tear or cosmetic damage, nor does it cover markings or retained images on the
picture tube resulting from viewing ¿xed images (including, among other things, letterbox pictures on
standard 4:3 screen TV’s, or non-expanded standard 4:3 pic tures on wide screen TV’s, or onscreen data in
a stationary and ¿xed location). The warranty ALSO DOES NOT COVER damages which occurred in
shipment, or failures which are caused by products not supplied by the warrantor, or failures which result
from accidents, misuse, abuse, neglect, mishandling, misapplication, alteration, faulty installation, set-up
adjust ments, misadjustment of consumer controls, improper maintenance, power line surge, lightning
damage, modi¿cation, or commercial use (such as in a hotel, of¿ce, restaurant, or other business), rental
use of the product, service by anyone other than a Factory Servicenter or other Authorized Servicer, or
damage that is attributable to acts of God.
THERE ARE NO EXPRESS WARRANTIES EXCEPT AS LISTED UNDER “LIMITED WARRANTY
COVERAGE.” THE WARRANTOR IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL
DAMAGES RESULTING FROM THE USE OF THIS PRODUCT, OR ARISING OUT OF ANY BREACH OF
THIS WARRANTY. (As examples, this excludes damages for lost time, cost of having someone remove or
re-install an installed unit if applicable, or travel to and from the servicer, loss of media or images, data or
other memory or recorded content. The items listed are not exclusive, but are for illustration only.)
ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTY OF MERCHANTABILITY,
ARE LIMITED TO THE PERIOD OF THE LIMITED WARRANTY.
Some states do not allow the exclusion or limitation of incidental or consequential damages, or limitations
on how long an implied warranty lasts, so the exclusions may not apply to you.
This warranty gives you speci¿c legal rights and you may also have other rights which vary from state to
state. If a problem with this product develops during or after the warranty period, you may contact your
dealer or Servicenter. If the problem is not handled to your satisfaction, then write to the warrantor’s
Consumer Affairs Department at the addresses listed for the warrantor.
PARTS AND SERVICE (INCLUDING COST OF AN IN-HOME SERVICE CALL, WHERE APPLICABLE)
WHICH ARE NOT COVERED BY THIS LIMITED WARRANTY ARE YOUR RESPONSIBILITY.
Product Parts Labor Service Contact Number
Camcorder One (1) Year (except CCD
Image Sensor)
CCD Image Sensor - 6 (Six)
Months
Ninety (90) Days
Ninety (90) Days
Carry-In or Mail-In 1-800-211-PANA(7262)
DVD/VCR Deck,
A/V Mixer
One (1) Year Ninety (90) Days Carry-In or Mail-In 1-800-211-PANA(7262)
TV/VCR,
TV/DVD,
TV/DVD/VCR
Combination
One (1) Year (except CRT)
CRT - Two (2) Years
Ninety (90) Days
Ninety (90) Days
Carry-In: 21Ǝ CRT and
Smaller
In-Home or Carry-In: 22Ǝ
CRT and Larger
1-800-211-PANA(7262)
TV/HDR
Combination
One (1) Year (except CRT)
CRT - Two (2) Years
Ninety (90) Days
Ninety (90) Days
In-Home or Carry-In 1-888-843-9788
Rechargeable
Batteries
(in exchange for
defective item)
Ten (10) Days Not Applicable Carry-In or Mail-In 1-800-211-PANA(7262)
Tape
(in exchange for
defective item)
Five (5) Days Not Applicable Carry-In or Mail-In 1-800-211-PANA(7262)
Memory Cards (in
exchange for
defective item)
Ninety (90) Days Not Applicable Carry-In or Mail-In 1-800-211-PANA(7262)
Limited Warranty
-6-
REC 12:00PM CH 08
0:47 0:12:20
SLP
NO V-CHIP DATA
Press POWER on remote or unit.
Use CH Ÿź or NUMBER keys to select
a channel.
Press VOL + or VOL - to adjust volume.
■ Using 100 key
When selecting CABLE channels 100 to 125 with
NUMBER keys, ¿rst press 100 key, and then enter
the remaining two digits.
■ Rapid Tune
Press R-TUNE to display the last channel you were
watching.
■ Audio Mute
Press MUTE to instantly mute the sound. Press
again to restore the previous sound level.
■ Phones
Connect an earphone (not supplied) or headphones
(not supplied) to PHONES Jack.
NIGHT Mode
Color and picture intensity levels are adjusted so
the screen is easier on your eyes during night time
use.
Press NIGHT to set.
Press NIGHT to cancel.
• Previous settings are
restored.
• NIGHT mode is canceled
when power is turned off or
power failure occurs.
TV Operation
Selecting Input Mode
■ Method 1
Press INPUT repeatedly.
Channel Number Ù LINE
1
2
3
125LINE
(CABLE)
69
(TV)
or
Press DISPLAY to display or remove overlay.
Whenever a blank section of a tape comes up in
Play mode, or when the selected channel has no
broadcast signal with the Weak Signal Display set
to “OFF”, the screen will turn solid blue.
Function Status Current Time
Rec Time Remaining
(OTR mode only, see p. 7)
Counter
Tape Speed
Channel
VCR Status & Clock Display
Blue Screen Display
ACTION key on unit
Using ŸźŻ Ź keys
Ÿ : CH UP
ź : CH DOWN
Ź : VOLUME UP
Ż : VOLUME DOWN
Whenever the menu or program screen is
displayed, CHANNEL UP/DOWN function as Ÿź
and VOLUME UP/DOWN function as ŻŹ only.
On Remote On Unit
On Unit
You can operate the menu screen using unit
buttons. To display the menu, press STOP/EJECT
and REW together with no tape inserted. To exit
the menu, repeat above.
STOP/EJECT REW/
ACTION
VOL CH
Auto Operation Functions
■ Auto Shut Off
No broadcast signal in TV (Only when Weak Signal
Display is set to OFF), blank tape is played for 5
minutes
Ö Power turns off
• This feature is cancelled if any button is pressed during
above mode.
■ Auto Playback
Insert a tape Ö Power comes on
Ö Play starts if there is no record tab
■ Auto Rewind
Tape end Ö Rewind Ö Stop
■ Playback Auto Eject
(Repeat Play is “OFF”)
Play Ö Tape end Ö Rewind Ö Stop
Ö Tape ejects if there is no record tab
1
2
CH 08
3
24
NIGHT
■ Method 2
Press CH Ÿź. Display will change as below.
Note:
• You can set the Input mode from MENU.
MAIN MENU
Ö TV Ö INPUT SELECT Ö TUNER or
LINE
Basic Operation (Unit)
-5-
VHF/UHF
VHF/UHF
VHF/UHF
VHF/U
H
F
If “AUTO CLOCK SET IS INCOMPLETE”
appears, manually set clock. See “Manual
Clock Set” section.
Initial Setup (Ready to Play)
Plug unit power cord into AC wall
outlet.
• If you use a cable box,
turn it on and set it to
the Public
Broadcasting Service
(PBS) channel in your
time zone. If you use a
DSS receiver, it must
be turned off.
Settings are made automatically.
When complete, this screen
appears.
■ For ANT./Cable
Connect the cable from Antenna/Cable to
the VHF/UHF terminal on unit.
IN from
ANT./CABLE
VHF/UHF
Please make all cable or antenna connections before power on.
Cable TV
Converter Box
Connecting
IN from
ANT./CABLE
Press POWER on remote or unit.
Auto channel and clock set starts.
UNIT (rear view)
UNIT (rear view)
■ For DSS/Cable Box
Connect the OUT jack on your cable box to
the VHF/UHF terminal on unit with a RF
cable.
Notes:
• Function buttons are void during Initial Setup.
• To eject a tape during Auto Set, press EJECT on
remote. Then make settings manually. (See
Advanced Operations book, p10.)
• If Auto Clock Set takes more than 30 minutes, press
STOP and perform settings manually. (See
Advanced Operations book, p10.)
VHF/UHF
Manual Clock Set
If AUTO CLOCK SET was incomplete.
Press ACTION on remote to display
SET CLOCK menu.
Press Ÿź to select the month and
Ź to set. In the same manner, select
and set the date, year, time, and
DST. (Daylight Saving Time)
Press ACTION to start clock and
exit.
Reset all unit Memory Functions
Returns to factory setting. Use if relocating
unit, or if Initial Setup needs to be redone.
• Make sure a tape is not inserted in unit.
Turn unit Power on.
Press and hold both PLAY/REPEAT
and FF on unit for more than 5
seconds.
• The power will shut off.
• Please ignore “NO CASSETTE” warning.
Do “Initial Setup” at left.
1
2
CH AUTO SET PROCEEDING
AUTO CLOCK SET
PROCEEDING
CANCEL:STOP
3
1/ 4/2004 SUN 12:00PM
DST:ON
SETTING : CH
AUTO CLOCK SET
COMPLETED
AUTO CLOCK SET
IS INCOMPLETE
PLEASE SET CLOCK BY
PRESSING ACTION KEY
1
SET CLOCK
1/ 1/2004 THU 12:00AM
DST:ON
-----------------------
SELECT: SET:
START :ACTION
2
SET CLOCK
1/ 4/2004 SUN 12:00AM
DST:ON
-----------------------
SELECT: SET:
START :ACTION
3
1
2
3
CAUTION
Overtightening “Nut type” RF coaxial cables
may damage jacks. Finger tighten only.
Connections/Initial Setup (Ready to Play)
Note to CABLE System Installer
This reminder is provided to call the CABLE
(Cable TV) System Installers attention to
Article 820-40 of the NEC that provides
guidelines for proper grounding and, in
par ticular, speci¿es that the cable ground
shall be con nect ed to the grounding system
of the building, as close to the point of cable
entry as practical.
Congratulations Loading the
Batteries
Head Cleaning Features for a
Quality Picture
Record/Playback
Time
DST (Daylight
Saving Time)
Accessories Prevent
Accidental Tape
Erasure
SpeciÀcations Connecting Initial Setup
(Ready to Play)
Manual Clock Set Reset all unit
Memory
Functions
-4-
Head Clog Sensor
Screen-left appears during
play if clogging is detected.
To remove screen, press
PLAY.
Congratulations
• Date of Purchase
• Dealer Purchased From
• Dealer Address
• Dealer Phone No.
• Model No.
• Serial No.
Accessories
To order accessories,
call toll free 1-800-332-5368.
Battery replacement caution
• Do not mix old and new batteries.
• Do not mix alkaline with manganese batteries.
Break off the tab to
prevent recording.
Record
Tab
Screwdriver
To record again.
Cover the hole with
cellophane tape.
Loading the Batteries
Prevent Accidental Tape Erasure
■ Remote Control
■ Batteries 2 “AA”
on your new purchase! With proper use, this
dependable product will provide years of
enjoyment. Please ¿ll in the information below.
(Serial number is on tag on back of unit.)
EUR7723010
Old or damaged tapes may clog heads.
Head Cleaning
Record/Playback Time
Only use tapes with the mark in this unit.
Digital Auto Tracking
Continuously analyzes the signal and adjusts for
optimum picture quality.
Manual Tracking Control
(to reduce picture noise)
Use during Playback and Slow Motion mode to
reduce picture noise. Press the 3 or 6 number key on
the remote control or CH Ÿź on the unit until the
picture clears up. To return to Auto Tracking, press
POWER off, then on again a few seconds later.
Features for a Quality Picture
Tape Speed
Setting
Type of Video Cassette
T120 T160 T180
SP
(Standard
Play)
2 Hours
2 Hours
40
Minutes
3 Hours
SLP
(Super Long
Play)
6 Hours8 Hours9 Hours
• Use “dry” type head cleaning cassette only.
(Part No. NV-TCL30PT is recommended.)
• Follow cleaning tape instructions carefully.
Excessive use of tape can shorten head life.
Speci¿cations
Note:
• Designs and spec i¿ca tions are sub ject to change without
no tice.
Unit auto adjusts clock for DST.
DST (Daylight Saving Time)
Display
Picture Tube
• 13 inch measured diagonal
90° deÀection Picture Tube
(PV-C1324/PV-C1334W)
• 20 inch measured diagonal
90° deÀection Picture Tube
(PV-C2024)
VCR
Video Recording
System
2 rotary heads helical scanning
system
Audio Track 1 track
Tuner
Broadcast Channels VHF 2 ~ 13, UHF 14 ~ 69
CABLE Channels
Midband A through I (14 ~ 22)
Superband J through W (23 ~
36) Hyperband AA ~ EEE (37 ~
64) Lowband A-5 ~ A-1 (95 ~ 99)
Special CABLE chan nel 5A(01)
Ultraband 65 ~ 94, 100 ~ 125
General
Power Source 120 V AC, 60 Hz
Power
Consumption
Power
On
• Approx. 69 W
(PV-C1324/PV-C1334W)
• Approx. 110 W (PV-C2024)
Power
Off
Approx. 2.5 W
Television System EIA Standard NTSC color
Speaker 1 pieces
Operating
Temperature
5 °C ~ 40 °C (41 °F ~ 104 °F)
Operating Humidity 10 % ~ 75 %
Weight
• 12 K
g
(26.4 lbs.)
(PV-C1324/PV-C1334W)
• 23 K
g
(50.6 lbs.) (PV-C2024)
Dimensions
(W X H X D)
• 386 mm (15-3/16
s) X 385 mm
(15-3/16
s) X 374 mm (14-3/4s)
(PV-C1324/PV-C1334W)
• 515 mm (20-5/16
s) X 505 mm
(19-7/8
s) X 474 mm (18-11/16s)
(PV-C2024)
■ Spring (First Sunday in April)
DST: ON Ö Sets clock ahead one hour.
■ Autumn (Last Sunday in October)
DST: ON Ö Turns clock back one hour.
• If your area does not observe Daylight Saving Time,
select DST: OFF.
• Keep these time changes in mind when programming
unit for timer recordings.
VIDEO HEADS MAY
NEED CLEANING
PLEASE INSERT HEAD
CLEANING CASSETTE
OR REFER TO MANUAL
END:PLAY
Before Using
-3-
Customer Services Directory
AVERTISSEMENT:
AFIN DE PRÉVENIR TOUT RISQUE D’INCENDIE OU DE CHOCS
ÉLECTRIQUES, NE PAS EXPOSER CET APPAREIL À LA PLUIE OU À
UNE HUMIDITÉ EXCESSIVE.
ATTENTION:
POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA LAME
LA PLUS LARGE DE LA FICHE DANS LA BORNE
CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.
FCC WARNING:
ANY UNAUTHORIZED CHANGES OR MODIFICATIONS TO THIS
EQUIPMENT WOULD VOID THE USER’S AUTHORITY TO OPERATE.
This symbol warns the user that uninsulated voltage
within the unit may have suf¿cient magnitude to cause
electric shock. Therefore, it is dangerous to make any
kind of contact with any inside part of this unit.
CAUTION: TO REDUCE THE RISK
OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS
INSIDE REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION
This video recorder, equipped with the HQ (High Quality) System, is compatible with existing VHS
equipment. Only use those tapes with the mark. It is recommended that only cassette tapes
that have been tested and inspected for use in 2, 4, 6, and 8 hour VCR machines be used. This
television receiver provides display of television closed captioning in accordance with §15.119 of
the FCC rules.
As of October 2003
Obtain Product Information and Operating Assistance; locate your nearest Dealer or
Servicenter; purchase Parts and Accessories; or make Customer Service and Literature
requests by visiting our Web Site at:
http://www.panasonic.com/support
or, contact us via the web at:
http://www.panasonic.com/contactinfo
You may also contact us directly at:
1-800-211-PANA (7262),
Monday-Friday 9 am-9 pm; Saturday-Sunday 10 am-7 pm, EST.
Service in Puerto Rico
Matsushita Electric of Puerto Rico, Inc. Panasonic Sales Company
Factory Servicenter:
Ave. 65 de Infantería, Km. 9.5, San Gabriel Industrial Park, Carolina, Puerto Rico 00985
Phone (787)750-4300 Fax (787)768-2910
For hearing or speech impaired TTY users, TTY : 1-877-833-8855
Purchase Parts, Accessories and Instruction Books online for all Panasonic Products by
visiting our Web Site at:
http://www.pasc.panasonic.com
or, send your request by E-mail to:
[email protected]
You may also contact us directly at:
1-800-332-5368 (Phone) 1-800-237-9080 (Fax Only) (Monday – Friday 9 am to 8 pm, EST.)
Panasonic Services Company
20421 84th Avenue South,
Kent, WA 98032
(We Accept Visa, MasterCard, Discover Card, American Express, and Personal Checks)
Accessory Purchases
For hearing or speech impaired TTY users, TTY : 1-866-605-1277
WARNING
CAUTION
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS
EQUIPMENT TO RAIN OR MOIS TURE.
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG
TO WIDE SLOT, FULLY INSERT.
This symbol alerts the user that important literature
concerning the operation and main tenance of this unit
has been included. Therefore, it should be read carefully
in order to avoid any problems.
This product utilizes both a Cathode Ray Tube (CRT) and other components that contain lead.
Disposal of these materials may be regulated in your community due to environmental
considerations. For disposal or recycling information please contact your local authorities, or
the Electronics Industries Alliance: <http://www.eiae.org.
>
Important Safeguards and Pre cau tions Safety Precautions/Mesures de sécurité Customer Services Directory
Safety Precautions/Mesures de sécurité
-2-
1 SAFE ANTENNA AND CABLE
CONNECTION
An outside antenna or cable system must be
properly grounded to provide some protection
against built up static charges and voltage. Section
810 of the National Electrical Code, ANSI/NFPA 70
(in Canada, part 1 of the Canadian Electrical Code)
provides information regarding proper grounding of
the mast and supporting structure, grounding of the
lead-in wire to an antenna discharge unit, size of
grounding conductors, location of antenna
discharge unit, con nec tion to grounding electrodes,
and requirements for the grounding electrode.
2 KEEP ANTENNA CLEAR OF HIGH
VOLTAGE POWER LINES OR CIRCUITS
Locate an outside antenna system well away from
power lines and electric light or power circuits so it
will never touch these power sources should it ever
fall. When installing antenna, absolutely never
touch power lines, circuits or other power sources
as this could be fatal.
OUTDOOR ANTENNA INSTALLATION
USING THE UNIT
INSTALLATION
1 POWER SOURCE CAUTION
Operate only from power source indicated on unit
or in this manual. If uncertain, have your Electric
Utility Service Company or Video Products Dealer
verify your home power source.
2 POWER CORD PLUG
For safety, this unit has a polarized type plug (one
wide blade), or a three-wire grounding type plug.
Always hold the plug ¿rmly and make sure your
hands are dry when plugging in or unplugging the
AC power cord. Regularly remove dust, dirt, etc. on
the plug.
POLARIZED PLUG CAUTION:
The plug ¿ts into outlet one way. If it cannot be fully
inserted, try reversing it. If it still will not ¿t, have an
electrician install the proper wall outlet. Do not
tamper with the plug.
GROUNDING PLUG CAUTION:
The plug requires a three-hole grounding outlet. If
necessary, have an electrician install the proper
outlet. Do not tamper with the plug.
3 POWER CORD
To avoid unit malfunction, and to protect against
electrical shock, ¿re or personal injury:
- Keep power cord away from heating appliances and
walking traf¿c. Do not rest heavy objects on, or roll such
objects over the power cord.
- Do not tamper with the cord in any way.
- An extension cord should have the same type plug
(polarized or grounding) and must be securely
connected.
- Overloaded wall outlets or extension cords are ¿re
hazards.
- Frayed cords, damaged plugs, and damaged or cracked
wire insulation are hazardous and should be replaced by
a quali¿ed electrician.
4 DO NOT BLOCK VENTILATION HOLES
Ventilation openings in the cabinet release heat
generated during operation. If blocked, heat
build-up may result in a ¿re hazard or heat damage
to cassettes.
For your protection:
a. Never cover ventilation slots while unit is ON, or
operate unit while placed on a bed, sofa, rug, or
other soft surface.
b. Avoid built-in installation, such as a book case
or rack, unless properly ventilated.
5 AVOID EXTREMELY HOT LOCATIONS
OR SUDDEN TEMPERATURE CHANG ES
Do not place unit over or near a heater or ra di ator,
in di rect sunlight, etc. If unit is sud denly moved
from a cold place to a warm place, mois ture may
condense in unit and on the tape caus ing damage.
6 TO AVOID PERSONAL INJURY
• Never place unit on support or stand
that is not ¿rm, level, and adequately
strong. The unit could fall causing
serious injury to a child or adult and
damage to the unit.
• Move any appliance and cart
combination with care. Quick stops,
excessive force, and uneven surfaces
may cause objects to overturn.
• Carefully follow all operating
instructions.
Before unit is brought out of storage or moved to a
new location, refer again to the INSTALLATION
section of these safe guards.
1 KEEP UNIT WELL AWAY FROM WATER
OR MOISTURE, such as vases, sinks,
tubs, etc.
2 IF EXPOSED TO RAIN, MOISTURE, OR
STRONG IMPACT, unplug unit and have it
inspected by a quali¿ed service technician
before use.
3 ELECTRICAL STORMS
During a lightning storm, or before leaving unit
unused for extended periods of time, disconnect all
equipment from the power source as well as the
antenna and cable system.
4 WHEN UNIT IS PLUGGED IN
• DO NOT OPERATE IF:
- liquid has spilled into unit.
- unit was dropped or otherwise damaged.
- unit emits smoke, malodors, or noises.
Immediately unplug unit, and have it inspected by a
service technician to avoid potential ¿re and shock
hazards.
• Never drop or push any object through openings in unit.
Touching internal parts may cause electric shock or ¿re
hazard.
• Keep magnetic objects, such as speakers, away from
unit to avoid electrical interference.
5 USING ACCESSORIES
Use only accessories recommended by the
manufacturer to avoid risk of ¿re, shock, or other
hazards.
6 CLEANING UNIT
Unplug unit. Use a clean, dry, chemically untreated
cloth to gently remove dust or debris. DO NOT USE
cleaning Àuids, aerosols, or forced air that could
over-spray, or seep into unit and cause electrical
shock. Any substance, such as wax, adhesive tape,
etc. may mar the cabinet surface. Exposure to
greasy, humid, or dusty areas may adversely affect
internal parts.
SERVICE
1 DO NOT SERVICE PRODUCT
YOURSELF
If, after carefully following detailed operating
instruc tions, the unit does not operate properly, do
not attempt to open or remove covers, or make any
adjustments not described in the manual. Unplug
unit and contact a quali¿ed service tech nician.
2 REPLACEMENT OF PARTS
Make sure the service technician uses only parts
speci¿ed by the manufacturer, or have equal safety
char ac ter istics as original parts. The use of
unauthorized substitutes may result in ¿re, electric
shock, or other hazards.
3 SAFETY CHECK AFTER SERVICING
After unit is serviced or repaired, request that a
through safety check be done as described in the
manufacturer’s service literature to ensure video
unit is in safe operating condition.
GROUND
CLAMP
ELECTRIC
SERVICE
EQUIPMENT
ANTENNA LEAD
IN WIRE
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
GROUNDING
CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
POWER SERVICE
GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
NEC - NATIONAL
ELECTRICAL CODE
TO REDUCE THE RISK OF ELECTRIC SHOCK, FIRE, INJURY TO PERSONS OR
DAMAGE TO THIS PRODUCT, READ AND RETAIN ALL SAFETY AND OPERATING
INSTRUCTIONS. HEED ALL WARNINGS IN THE MANUAL AND ON THE PRODUCT.
WARNING
IMPORTANT SAFEGUARDS AND PRE CAU TIONS
-7-
Record On a Tape
Playback a Tape
Record tab
■ Press REW to rewind tape
■ Press FF to fast forward tape
■ Press EJECT on remote or
STOP/EJECT on unit to eject tape
Note:
• After 5 minutes in Pause mode, unit stops to protect
the tape and the video heads.
■ One Touch Recording (OTR)
Press REC repeatedly to set length as follows:
30 min. Ö 1 hr. Ö 1:30 Ö 2:00 Ö 3:00 Ö 4:00
Ö exit
■ Press FF to forward scene search
■ Press REW to reverse scene search
Notes:
• After search has begun, each additional press of
FF or REW changes speed.
• FF and REW search speed may vary depending
on current tape position.
• After 10 minutes in search mode, unit returns to
Play mode to protect the tape and the video
heads.
■ To Replace program...
■ To Clear program...
1) Press Ź.
2) Repeat step 4 (at
left) to set new
programs.
3) Press PROG.
Cancel a Timer Recording
Press ADD/DLT.
Review, Replace or Clear Program Contents
Today’s
Date
Example
DAILY(day)
7
2
1
31
68 9
SELECT / Selection Order
WEEKLY
(SA)
WEEKLY
(MO)
WEEKLY
(SU)
Notes:
• 2 minutes before Timer recording is performed,
“PLEASE PREPARE FOR TIMER REC” appears
and/or the PROG TIMER Indicator Àashes. Be sure
a cassette with record tab is loaded and the unit is in
Stop mode.
• If there is a power interruption of more than one
minute, the recording may not be performed or
continued.
Hold down STOP for a few seconds to cancel
the Timer Recording.
• Any future daily or weekly recordings will be
performed as programmed.
(Recording is not in progress)
(Recording is in progress)
Timer Recording
• 1~31 = One time
• DAILY = Mon,~Fri.
• WEEKLY = Same time
each week
1
Insert a tape.
• Unit power comes
on automatically.
• Loose or peeling
labels may cause
tape jam.
2
Press PLAY.
• Playback begins if
tape has no record
tab.
3
Press STOP.
1
Press PROG to display SET
PROGRAM screen.
2
Press Ÿź to select TIMER PROGRAMMING.
SET PROGRAM
TIMER PROGRAMMING
ON TIMER
SELECT: SET:
END :PROG
3
Press Ź to display screen.
1) Press Ź.
2) Set record DATE,
press Ÿź to select:
P DT START STOP CH SPD
1 -- --:-- --:-- -- --
2 -- --:-- --:-- -- --
3 -- --:-- --:-- -- --
4 -- --:-- --:-- -- --
SELECT: SET:
END :PROG
4
5
Press PROG to end the program.
To Enter More Programs, press Ÿź to
select and Ź to set an unused
program. Then repeat step 4.
P DT START STOP CH SPD
1 10 9:00a12:00p 08 SP
2 -- --:-- --:-- -- --
3 -- --:-- --:-- -- --
4 -- --:-- --:-- -- --
SET COMPLETED
CANCEL:ADD/DLT
SELECT: SET:
END :PROG
6
Press PROG twice to exit this mode.
• If you’re using a cable box, make sure that it is
tuned to the desired channel and the power is
left on for timer recording.
• PROG TIMER indicator lights on unit.
3) Set remaining items,
press Ź to set
START/ STOP times,
Channel or LINE, and
tape speed. Then
press Ÿź to select.
1
Insert a tape with record tab.
• The unit power comes on automatically.
2
Press CH Ÿź or NUMBER keys to
select a channel.
• For “LINE” input, see p. 6.
3
Press SPEED to select recording
speed. (P. 4)
4
Press REC to start recording.
• To edit, press PAUSE/SLOW to pause, and
again to resume recording.
5
Press STOP to stop recording.
1
Repeat steps 1~3 at left.
2
Press Ÿź to select the desired
program.
P DT START STOP CH SPD
1 10 9:00a12:00p 08 SP
2day 11:00a11:30a125 SLP
3 12 8:00p 9:30p L SP
4 -- --:-- --:-- -- --
CANCEL:ADD/DLT
SELECT: SET:
END :PROG
P DT START STOP CH SPD
1 10 9:00a12:00p 08 SP
2day 11:00a11:30a125 SLP
3 12 8:00p 9:30p L SP
4 -- --:-- --:-- -- --
SELECT: SET:
EXIT :PROG
P DT START STOP CH SPD
1 -- --:-- --:-- -- --
2day 11:00a11:30a125 SLP
3 12 8:00p 9:30p L SP
4 -- --:-- --:-- -- --
SELECT: SET:
END :PROG
3
Press PROG twice to exit this
mode.
Basic Operation (Tape)
TV
Operation
VCR Status &
Clock Display
Blue Screen
Display
Auto Operation
Functions
NIGHT Mode Selecting
Input Mode
Channel &
Function
Display
ACTION
key on
unit
Usingʆʈʉ ʇ
keys
Playback a
Tape
Timer
Recording
Record On a
Tape
Review, Replace
or Clear Program
Contents
Cancel a Timer
Recording
Notes:
• These features work best in SLP mode.
• After 3 minutes in Still or Slow mode, unit stops to
protect the tape and the video heads.
■
Press PAUSE/SLOW to still (freeze) picture
■ Hold down PAUSE/SLOW in Still
mode to slow motion picture
Ö Press PLAY to release.
-1 2-
Check the following points once again if you are having trouble with your unit.
(BO: refers to “Basic Operations” Instruction book.)
(AO: refers to “Advanced Operations” Instruction book.)
If you cannot resolve the problem, please call the Customer
Call Center for product
assistance at 1-800-211-PANA(7262).
To locate an authorized servicenter, please call toll free 1-800-211-PANA(7262)
or, contact us via the web at:http://www.panasonic.com/contactinfo.
Power CORRECTION
No power…
Completely insert Power Plug into an AC outlet.
Set POWER button ON.
Monitor CORRECTION
No picture or sound...
Make sure your antenna system (TV or CABLE) is correctly set.
(AO p. 10)
Completely insert Power Plug into an AC outlet.
Set POWER button to ON.
Poor picture with normal
sound...
Adjust BRIGHTNESS, SHARPNESS, and PICTURE controls in
the SET UP TV menu. (AO p. 2)
Poor sound with normal
picture...
Adjust VOLUME control. (BO p. 6)
Poor TV reception...
Adjust SHARPNESS and PICTURE controls in the SET UP TV
menu. (AO p. 2)
No color or poor color...
Adjust TINT and COLOR controls in the SET UP TV menu.
(AO p. 2)
Ghost (multiple) images... Install a directional antenna.
TV programs cannot be
watched...
Make sure the selected channel is in unit’s memory. (AO p. 10)
Channel cannot be selected... Only the channel being recorded can be viewed on this unit.
VCR CORRECTION
TV program cannot be
recorded...
Make sure your antenna system (TV or CABLE) is correctly set.
(AO p. 10)
Make sure cassette record tab is intact. (BO p. 4)
Timer recording cannot be
performed…
Check that clock is set to current time and date.
Make sure DSS/CABLE box (if used) is left on and tuned to
channel to be recorded.
Set recording Start/Stop times correctly. (BO p. 7)
Timer recording may not be performed or continued if a power
interruption of more than 1 minute occurs before or during a Timer
Recording, even after power is restored.
No playback picture, or the
playback picture is noisy or
contains streaks...
Adjust TRACKING control in either direction. (BO p. 4)
Try Head Cleaning. (BO p. 4)
VCR cannot be controlled...
Make sure VCR LOCK is set to off. (AO p. 5)
Make sure unit is not in a Timer Record operation.
Remote Control CORRECTION
Unit cannot be controlled...
Aim remote at remote sensor on unit (BO p. 9) so that signal is
unobstructed.
Inspect the remote batteries. (BO p. 4)
Make sure VCR LOCK is set to off. (AO p. 5)
Exposing unit remote sensor to direct Àuorescent or outdoor light
may cause signal interference.
ACTION and PROG buttons
cannot be selected...
Check remote batteries.
Miscellaneous CORRECTION
Video cassette cannot be
inserted...
Insert the cassette window side up; record tab facing you.
Video cassette cannot be
removed...
Completely insert Power Plug into an AC outlet.
Tape cannot be ejected or
inserted...
Try ejecting or inserting the tape again after turning POWER off,
then back on.
Video cassette ejects when a
recording is started, or the
power is turned off for timer
recording...
Make sure cassette record tab is intact. (BO p. 4)
In Stop mode, the VCR motor
(CYLINDER) continues to
rotate...
To enable Quick Play mechanism, the VCR cylinder will rotate for
about 3 minutes. This reduces response time from Stop to Play
mode and from Play to Rewind Search mode.
VCR cannot be controlled... Make sure VCR LOCK is set to off. (AO p. 5)
Before Requesting Service
Warning and Instruction Displays Before Requesting Service
-1 1-
Warning and Instruction Displays
These displays will alert you to a missed operation or provide further instructions.
OSD CAUTION Page
PLEASE SET CLOCK BY
PRESSING ACTION KEY
If you attempt to set or review a Timer
Recording, or set the On-Timer and the Clock is
not set...
See page 7 of Basic
Operations and see page
2 of Advanced Operations
book.
CHECK CASSETTE
RECORD TAB
If you press REC, and a cassette is inserted
with no record tab...
See pages 4 and 7 of
Basic Operations book
TO CANCEL TIMER REC
HOLD DOWN STOP KEY
FOR APPROX 3 SEC
If you press STOP during a Timer Recording...
See page 7 of Basic
Operations book
NO CASSETTE
If you press PLAY, FF, REW, or REC without a
cassette inserted...
PLEASE PREPARE
FOR TIM ER REC
If the unit is not in Stop mode, or cassette is not
inserted, or cassette has no record tab, or tape
is at its end two minutes before a Timer
Recording is about to begin...
VIDEO HEADS MAY
NEED CLEANING
PLEASE INSERT HEAD
CLEANING CASSETTE
OR REFER TO MANUAL
END: PLAY
If head cleaning becomes necessary while
playing back a tape...
See page 4 of Basic
Operations book
VCR LOCK ACTIVATED
If you press a function button other than
STOP/EJECT or POWER while the unit is in
VCR Lock mode...
See page 5
-10-
Language Channels Clock
Time Zone Adjust
and press Ź
repeatedly to
select mode.
(“TIME ZONE ADJUST”
appears only when auto
clock is set.)
(Only when Auto Clock
is set.)
Press ACTION to display MAIN MENU.
0
+
1
-
1
Add or Delete a Channel
■ To add channel
Select channel with number keys and press
ADD/DLT.
■ To delete channel
Select channel with CH Ÿź or number keys
and press ADD/DLT.
MAIN MENU
TV LOCK LANGUAGE
CH CLOCK EXIT
SELECT:
SET :ACTION
1
Press ŸźŻ Ź
to select
“LANGUAGE.”
MAIN MENU
TV LOCK LANGUAGE
CH CLOCK EXIT
SELECT:
SET :ACTION
2
Press ACTION
repeatedly.
For Spanish
MENU PRINCIPAL
TV BLOQUEO IDIOMA
CANAL RELOJ SALIR
ELEGIR:
FIJAR :ACTION
For French
MENU
TELE BLOCAGE LANGUE
CANAL HORLOGE SORTIE
SEL. :
REGLER:ACTION
For English
MAIN MENU
TV LOCK LANGUAGE
CH CLOCK EXIT
SELECT:
SET :ACTION
3
Press ŸźŻ Ź
to select
“EXIT,” and
press ACTION
to exit.
1
Press ŸźŻ Ź
to select “CH,”
and press
ACTION.
MAIN MENU
TV LOCK LANGUAGE
CH CLOCK EXIT
SELECT:
SET :ACTION
2
Press Ÿź to
select
“ANTENNA,”
then press Ź to
set your
antenna system
(“TV” or
“CABLE”).
SET UP CHANNEL
ANTENNA : TV
AUTO SET
WEAK SIGNAL DISPLAY:ON
SELECT: SET:
END :ACTION
3
Press Ÿź to
select “AUTO
SET,” then
press Ź.
• After Channel Auto
Set is ¿nished,
Clock Auto Set will
be performed. (If
clock is set
manually, Clock
Auto Set will not be
performed.)
1
Press ŸźŻ Ź to select “CLOCK,”
and press ACTION.
MAIN MENU
TV LOCK LANGUAGE
CH CLOCK EXIT
SELECT:
SET :ACTION
2
Press Ÿź to
select
“MANUAL” or
“AUTO CLOCK
SET” and
press Ź.
SET CLOCK
AUTO CLOCK SET
MANUAL
TIME ZONE ADJUST : 0
SELECT: SET:
END :ACTION
3
Press Ÿź and
press ŻŹ to
select and set
the month,
date, year,
time, and DST
(Daylight
Saving Time).
(If select “MANUAL”)
SET CLOCK
1/ 4/2004 SUN 12:00AM
DST:ON
-----------------------
SELECT: SET:
START :ACTION
4
Press ACTION
twice to start
the clock and
exit this mode.
2
Press Ÿź to
select “TIME
ZONE
ADJUST,”
SET CLOCK
AUTO CLOCK SET
MANUAL
TIME ZONE ADJUST : 0
SELECT: SET:
END :ACTION
3
Press ACTION
twice to exit.
CHANNEL 08 ADDED
CHANNEL 08 DELETED
Reset Language, Channels, Clock, Time Zone Adjust
Copy Your Tapes (Dubbing) Reset Language, Channels, Clock, Time Zone Adjust
-9-
Copy Your Tapes (Dubbing)
Unauthorized exchanging and/or copying of copyrighted recordings may be copyright infringement.
Connections you’ll need to make.
Playback (Source) Recording (Editing) unit
(Perform operation of steps 4 and 5 on both units at same time.)
STOP
Recording (Editing) unit
OUT
IN
AUDIO
AUDIO INVIDEO IN
IN FROM ANT.
OUT TO TV
VID EO
Playing (Source) VCR
IMPORTANT
1
Insert pre-recorded tape.
3
Press PLAY then PAUSE at starting
point to put in Standby mode.
4
Press PLAY to start dubbing.
5
Press STOP to stop dubbing.
1
Insert blank tape with record tab.
• Dubbing tapes protected with Copy Guard will have
poor quality results.
2
Select “LINE” mode.
• See “Selecting Input Mode” (p. 6 of Basic Operations
book.)
3
Press REC, then PAUSE/SLOW
immediately to put in Standby mode.
4
Press PAUSE/SLOW to start dubbing.
5
Press STOP to stop dubbing.
-8-
Panasonic Consumer Electronics Company,
Division of Matsushita Electric Corporation of America
One Panasonic Way Secaucus,
New Jersey 07094
Panasonic Sales Company (“PSC”),
Division of Matsushita Electric of Puerto Rico, Inc.
Ave. 65 de Infanteria. Km. 9.5
San Gabriel Industrial Park, Carolina, Puerto Rico 00985
Printed in Indonesia
LSQT0768 B
S0104-1034
P
Please read these instructions carefully before attempting to connect,
operate, or adjust this product. Please save this manual.
As an
E
NERGY
S
TAR
®
Partner,
Matsushita Electric Corporation of Amer ica has de termined
that this prod uct or product mod el meets the
E
NERGY
S
TAR
®
guidelines for en ergy ef ¿ciency.
Models No. PV-C1324/PV-C1334W/
PV-C2024
Combination VCR
Operating Instructions
(Advanced Operations)
For Basic operations, see the separate
“Basic Operations” instruction book.
This operating instruction book is designed for use with models
PV-C1324, PV-C1334W and PV-C2024. Illustrations in this manual show
the PV-C2024.
LSQT0768 B
For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at: http://www.panasonic.com/contactinfo
Table of Contents
TV Features.......................................................................................................2
Closed Caption System .....................................................................................3
VCR Features ....................................................................................................4
V-Chip Control Features....................................................................................6
Copy Your Tapes (Dubbing) ..............................................................................9
Reset Language, Channels, Clock, Time Zone Adjust....................................10
Warning and Instruction Displays .................................................................... 11
Before Requesting Service..............................................................................12
-6-
V-Chip Control Features
Enter Secret Code
This unit has a built-in V-Chip Control which allows you to block unwanted TV usage based on US MOVIES
and US TV PROGRAMS Ratings.
A 4-digit code must be entered to view a blocked
program or change rating settings.
Notes:
• DO NOT forget your secret code.
• Once ratings are set, restricted tapes or programs
cannot be accessed unless the secret code is entered.
■ Changing your secret code
• Take care that you are not
observed entering the
secret code.
To Make Corrections,
Press Ż repeatedly to move the cursor, and press
Number keys to make the correction.
Enter Code Setup Blocking
If LOCK menu is not displayed, do “Enter Secret
Code” steps at left.
Setup US MOVIES Ratings
NR (Not Rated) PROGRAMS
Some movies, such as old movies or foreign movies
have no ratings.
• You will need your current code. Perform steps 1~3.
In step 4, press ADD/DLT to clear current code.
Repeat steps 3 and 4 to enter new code.
Note:
• “NEXT PAGE” displays CANADIAN V-Chip menu. Not
necessary except Canadian tapes or broadcasts.
■ “ON” ➞ V-Chip Control is activated.
■ “OFF” ➞ V-Chip Control is deactivated.
1
Press ACTION to display menu.
2
Press ŸźŻ Ź to select “LOCK,” and
press ACTION.
MAIN MENU
TV LOCK LANGUAGE
CH CLOCK EXIT
SELECT:
SET :ACTION
3
Press NUMBER keys to enter your
secret code, and enter same code again
for con¿rmation.
LOCK
ENTER 4-DIGIT CODE
- ---
ENTER :0-9
END :ACTION
4
Press Ź to display US Ratings menu
(see at right).
Or
Press ACTION twice to exit.
LOCK
CONFIRM 4-DIGIT CODE
RECOGNIZED
CHANGE CODE:ADD/DLT
CONTINUE:
END :ACTION
Enter Code Setup Blocking
1
Press Ÿź to select “US MOVIES,” and
press Ź to set “ON” or “OFF.”
LOCK
US MOVIES :OFF
CHANGE SETTINGS
US TV PROGRAMS :OFF
CHANGE SETTINGS
NEXT PAGE
SELECT: SET:
END :ACTION
2
Press Ÿź to select “CHANGE
SETTINGS,” and press Ź.
LOCK
US MOVIES :OFF
CHANGE SETTINGS
US TV PROGRAMS :OFF
CHANGE SETTINGS
NEXT PAGE
SELECT: SET:
END :ACTION
3
Press Ÿź to select “VIEW NR
PROGRAMS?,” and press Ź to set
“YES” or “NO.”
VIEW NR PROGRAMS? : YES
G UNLOCKED
PG
PG-13
R
NC-17
X
CONTAINS NO RATING
SELECT: SET:
END :ACTION
4
Press Ÿź to select and Ź to set
ratings. (See ratings chart on page 7.)
VIEW NR PROGRAMS? : YES
G UNLOCKED
PG
PG-13
R
NC-17
X
GENERAL AUDIENCE
SELECT: SET:
END :ACTION
5
Press ACTION to continue with US TV
PROGRAMS Ratings (see page 7).
Or, press ACTION three times to exit.
-5-
Tape Position and Tape Status Display
• “DETECTING TAPE
POSITION” only
appears the ¿rst time a
cassette is inserted
and it takes several
seconds for correct
indication to appear.
To ¿nd out present tape position and amount of
tape remaining.
When set to “ON,” picture is displayed
regardless of signal strength.
Weak Signal Display ON/OFF
Notes:
• ON: Picture is displayed even if signal is very weak
but quality may be poor.
OFF: Screen turns solid blue when signal is weak or
non-existent.
• Selecting “ON” has no effect on connected
equipment with blue back feature.
VCR Lock
All operations are prohibited except Timer
recording and tape eject. Useful for families
with small children.
Note:
• VCR Lock cancels in 24 hours.
To turn on,
hold down REC on the
unit in Stop mode with
no tape inserted for 7
sec.
(Please ignore the NO
CASSETTE warning.)
To turn off,
repeat above.
• The present tape
position indication and
amount of tape
remaining (according
to tape speed) is
displayed. Tape
remaining time display
may not be precise.
1
Press TAPE POSITION to detect
tape position.
DETECTING TAPE POSITION
SLP
R 120 MIN.
BEGIN END
2
Press TAPE POSITION to return to
normal screen.
1
Press ACTION to display menu.
2
Press ŸźŻ Ź to select “CH,” and
press ACTION.
MAIN MENU
TV LOCK LANGUAGE
CH CLOCK EXIT
SELECT:
SET :ACTION
3
Press Ÿź to select “WEAK SIGNAL
DISPLAY,” and press Ź to set “ON”
or “OFF.”
SET UP CHANNEL
ANTENNA : TV
AUTO SET
WEAK SIGNAL DISPLAY:ON
SELECT: SET:
END :ACTION
4
Press ACTION twice to return to
normal screen.
Tape Select
Select your tape length so the tape position and
amount of tape remaining is properly displayed.
(See “Tape Position and Tape Status Display”
section below.)
1
Press ACTION to display menu.
2
Press Ÿź to select “TV,” and press
ACTION.
MAIN MENU
TV LOCK LANGUAGE
CH CLOCK EXIT
SELECT:
SET :ACTION
3
Press Ÿź to select “TAPE SELECT,”
and press Ź to set “T-120,” “T-160”
or “T-180.”
SET UP TV
CAPTION
INPUT SELECT :TUNER
VIDEO ADJUST
TAPE SELECT :T-120
SELECT: SET:
END :ACTION
• Select “T-120” for
tapes 120 minutes or
less, “T-160” if 140 or
160 minutes, and
“T-180” if 180 minutes.
4
Press ACTION twice to return to
normal screen.
VCR LOCK ACTIVATED
VCR LOCK OFF
T-120 T-160 T-180
Tape position is displayed incorrectly in the
following cases:
• If VHS-C type cassettes, tapes under 30 minutes,
tapes over 180 minutes, or incompatible tapes are
used.
• If the correct tape length is not selected.
(See “Tape Select” section above.)
VCR Features (continued)
Index Search Commercial Skip Zero Search Repeat Play Tape Select Tape Position Display VCR Lock Weak Signal Display
ON/OFF
-4-
VCR Features
For each recording, an invisible index mark is
placed on the tape. A program index and
information and also included for Timer recordings.
These marks are used to access or Scan recording.
Index Search
NOTE:
indicates start points of each recording.
■ To Calculate Index Number
Example 2:
To go to rec. 6 from rec. 2, enter 4 and press FF.
6
157
2 34
17
5
34 6
2
Example 1:
To go to rec. 2 from rec. 4, enter 3 and press REW.
Note:
• If Index Search is started very close to an index mark,
that index mark may not be counted in the search.
Zero Search
To quickly return to a speci¿ed tape location.
• Unit will go into FF or REW mode and stops at the last
point the Counter was set to 0:00:00.
Commercial Skip
Unit fast forwards (skips) over 1, 2, or 3 minutes of
recorded tape as desired.
Repeat Play
Set to see a recording over and over.
Note:
• Play repeats at tape end or if unrecorded position over
30 sec. is detected.
In PLAY mode, press
PLAY/ REPEAT on unit
to turn “ON.”
Repeat above to turn
“OFF.”
1
Press SEARCH in Stop or Play mode,
and then press NUMBER keys to select
recording number.
• To calculate number, see below.
Press FF or REW to start search.
INDEX SEARCH
ENTER INDEX NUMBER :1
USING 1-9 KEYS
FORWARD SEARCH :FF
REVERSE SEARCH :REW
EXIT:SEARCH
2
Play begins at search end. To search
forward or back 1 index, press FF or
REW while screen below is displayed
(10 sec.).
• To cancel, press PLAY.
INDEX SEARCH
FORWARD SEARCH :FF
REVERSE SEARCH :REW
1
Press CM/ZERO in Play mode.
• Press CM/ZERO repeatedly to change skip time as
shown below.
• No indication appears.
1
Press COUNTER RESET during play
to display Counter.
2
Press COUNTER RESET at the
desired position to reset to “0:00:00.”
0:00:00
3
Continue to record, playback, etc.
4
Press STOP.
5
Press CM/ZERO in Stop mode to
start ZERO SEARCH.
-1:23:45
PLAY
REPEAT ON
PLAY
REPEAT OFF
-3-
OFF
CAP C1
TEXT C1
CAP C2
TEXT C2
Closed Caption Mode Feature
This multi-use system not only allows the hearing impaired to enjoy selected programs, but also
makes useful information from TV stations available to everyone.
■ Recording and Playing Back a
Closed Caption/Text Program
NO
CAP C1
CAP C2
Caption On Mute Feature
Closed Caption narration is displayed when
MUTE button is pressed for silence.
Record:
Record normally. Closed Caption/ Text
signal is recorded automatically.
Playback:
Start playback, and do above steps to
select desired caption mode.
Note:
• The closed caption or text signal may be broadcast
over C1, C2, or both. Also, text contents can vary so
you may wish to try different settings.
1
Press ACTION to display menu.
2
Press ŸźŻ Ź to select “TV,” and
press ACTION.
MAIN MENU
TV LOCK LANGUAGE
CH CLOCK EXIT
SELECT:
SET :ACTION
3
Press Ÿź to select “CAPTION,” and
press Ź.
SET UP TV
CAPTION
INPUT SELECT :TUNER
VIDEO ADJUST
TAPE SELECT :T-120
SELECT: SET:
END :ACTION
4
Press Ÿź to select “CAPTION
MODE,” and press Ź repeatedly to
select mode. (See below.).
CAPTION
CAPTION MODE : CAP C1
CC ON MUTE : NO
SELECT: SET:
END :ACTION
■ CAP C1 or CAP C2
A narration of selected TV programs is
displayed. Check TV program listings for
CC (Closed Caption) broadcasts.
■ TEXT C1 or TEXT C2
The lower half of the screen will be blocked
out. When the TV station broadcasts
information, such as program listings, it will
appear in this space.
■ OFF
Closed Caption / Text narration will not be
displayed.
5
Press ACTION three times to exit.
1
Do steps 1~3 at left.
2
Press Ÿź to select “CAPTION
MODE,” and press Ź repeatedly to
select “OFF.”
CAPTION
CAPTION MODE : OFF
CC ON MUTE : CAP C1
SELECT: SET:
END :ACTION
3
Press Ÿź to select “CC ON MUTE,”
and press Ź repeatedly to select a
mode. (See below.)
CAPTION
CAPTION MODE : OFF
CC ON MUTE : CAP C1
SELECT: SET:
END :ACTION
4
Press ACTION three times to exit.
5
Press MUTE to mute the sound and
display closed captioning.
• To cancel, press MUTE again.
Closed Caption System
Picture Adjustment ON-TIMER Sleep Timer Closed Caption Mode Feature Caption On Mute Feature
-2-
TV Features
Picture Adjustment
To Reset Picture Controls,
press Ÿź and Ź to select and set “NORMAL.” All
controls return to their factory settings.
■ COLOR Control
Adjust color intensity.
■ TINT Control
Adjust for natural Àesh tones.
■ BRIGHTNESS Control
Adjust picture brightness.
■ PICTURE Control
Adjust picture intensity by adjusting both contrast
and color level in the proper balance.
■ SHARPNESS Control
Adjust picture sharpness.
Press SLEEP repeatedly to set SLEEP TIMER.
• Pressing DISPLAY with sleep timer set displays
remaining time.
To cancel,
press SLEEP repeatedly until “SLEEP TIMER 0”
appears.
Sleep Timer
This unit can be set for auto power off.
SLEEP TIMER 30
SLEEP TIMER 60
SLEEP TIMER 90
SLEEP TIMER 0
1
Press ACTION to display menu.
2
Press ŸźŻ Ź to select “TV,” and press
ACTION.
MAIN MENU
TV LOCK LANGUAGE
CH CLOCK EXIT
SELECT:
SET :ACTION
3
Press Ÿź to select “VIDEO ADJUST,”
and press Ź.
SET UP TV
CAPTION
INPUT SELECT :TUNER
VIDEO ADJUST
TAPE SELECT :T-120
SELECT: SET:
END :ACTION
4
Press Ÿź to select an adjustment item
(see below.), and press ŻŹ to adjust.
COLOR
TINT
BRIGHTNESS
PICTURE
SHARPNESS
NORMAL
SELECT: ADJUST:
END :ACTION
5
Press ACTION three times to exit.
COLOR
TINT
BRIGHTNESS
PICTURE
SHARPNESS
NORMAL
SELECT: SET:
END :ACTION
This unit can be set to automatically power on in
one of 2 modes (TV, Playback).
Press PROG to display SET PROGRAM
screen.
• Make sure a tape is inserted if Playback mode is
selected.
• ON-TIMER mode
selection order
Press PROG to set ON TIMER.
• “ON TIMER SET” is displayed.
• ON TIMER Indicator lights on unit.
Press Ÿź to select “ON TIMER,” and
press Ź to display ON TIMER screen.
C
H
01
PLAY
C
H
125
C
H
02
C
H
03
To Cancel ON-TIMER ,
Repeat steps 1 and 2. Then, press ADD/DLT to
clear the time in step 3. Now, press PROG to end.
“ON TIMER END” brieÀy appears on-screen.
SET PROGRAM
TIMER PROGRAMMING
ON TIMER
SELECT: SET:
END :PROG
ON-TIMER
1
2
3
4
Press Ÿź to select desired settings,
and press Ź to set the ON-TIMER time
and ON-TIMER mode.
To Make Corrections, use Ÿź and ŻŹ to
move back and correct.
ON TIMER
10:--AM CH --
SELECT: SET:
END :PROG
ON TIMER
10:00AM CH 05
CANCEL:ADD/DLT
SELECT: SET:
END :PROG
CH 08
PROGRAM RATING EXCEEDED
RATING:PG-13
ACCESS CODE ----
ENTER :0-9
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Panasonic PVC2024 Operating instructions

Panasonic
Brand
Panasonic
Model
PVC2024
Category
Cassette players
Type
Operating instructions
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents