Dorel Home 4105419 Owner's manual

DO NOT RETURN TO THE STORE !

Visit www.dhpfurniture.com/eng/support-home

or call Toll-Free 1-800-267-1739

4105019

B34410501900 - 10125-M

Date of Purchase

Rockstar Metal Bunk Bed

F.C. - 2016/9/5

If parts are missing or damaged, we will gladly ship your

replacement parts free of charge.

Lot Number

Thank you for purchasing from DHP!

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY

INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE.

1

Twin Over Futon

Black

Weight Limit:

200 Lb / 91 Kg For Upper Bed

600 Lb / 272 Kg For Lower Futon

TM

Contact Us!

cs@dhpfurniture.com

DHP

410E, First Street South, Wright City, MO 63390, USA

Attention: Consumer Service.

Read Before Beginning Assembly

1-800-267-1739

Monday - Friday, 9:00 am - 5:00 pm (Eastern Time)

Warranty Information

2

B34410501900

Caution

DHP warrants this product to be free from defects in material and workmanship and

agrees to remedy any such defect. This warranty covers one year from the date of

original purchase. This is solely limited to the repair or replacement of defective

parts and assembly labor is not included.

This warranty does not apply to any product which has been improperly assembled,

subjected to misuse or abuse or which has been altered or repaired in any way.

Liability for consequential damages is excluded to the extent exclusion is permitted

by law. This warranty gives you specific legal rights and you may also have other

rights which vary from state to state.

To obtain warranty service, purchaser must present original bill of sale. Components

repaired or replaced are warranted through the remainder of the original warranty

period only. The defective components will be repaired or replaced without charge,

subject to the terms and conditions described above.

Visit www.dhpfurniture.com to view the limited warranty valid in the U.S. and

Canada.

 Call our toll free number if you need assistance.

 Work in a spacious area and near where the unit will be used, preferably on a

carpet, or use a piece of the cardboard packaging to protect your floor and product.

 Recommended # of people needed for assembly: 2 (however it is always better

to have an extra hand). Estimated assembly time is 2 hours.

 Make sure all parts are included. Most parts are labeled or stamped on the raw

edge.

 Read each step carefully. It is very important that each step of the instructions is

performed in the correct order. If these steps are not followed in sequence,

assembly difficulties will occur.

 This product is designed for home use and not intended for commercial use.

 This product contains small components. Please ensure that they are kept away

from small children.

 Do not use power tools to assemble your furniture. Power tools may strip or

damage the parts.

For help with assembly, identifying parts, product information or to order parts,

please contact us:

Page is loading ...

4

Parts

B34410501900

All in 1 big box!

Before you throw the package, please use the

Check Box to identify the parts and ensure that

you have all the parts needed for the assembly.

There are inner box(es) that include components

required to complete this assembly.

Replacement Parts, Visit www.dhpfurniture.com/eng/support-home

A

Post 1

T942230

X 2

B

E

X1

M

Post 2

T942240

X 2

Guard Rail

T941980

X 2

Side Guard Rail 1

T942000

X 1

Side Guard Rail 2

T941990

X 1

I2

I1

Left Lower Guard Rail

T609090

X 1

Right Lower Guard Rail

T609080

X 1

F1

H

Front Rail

T615980

X 1

Rear Rail

T605490

X 1

V

N

E1

X

Lower Bed Frame-1

T919760

X 1

Lower Bed Frame-2

T919770

X 2

Lower Bed Frame-3

T929000

X 1

Transversal Brace

T929010

X 1

A

B

E

M

X1

I1

H

I2

F1

V

N

E1

X

5

Parts

B34410501900

All in 1 big box!

Before you throw the package, please use the

Check Box to identify the parts and ensure that

you have all the parts needed for the assembly.

There are inner box(es) that include components

required to complete this assembly.

Replacement Parts, Visit www.dhpfurniture.com/eng/support-home

Z

O

K

S

T

U

Y

W

Q

Ladder

T614270

X 2

Upper Slat

T919600

X 22

Lower Slat

T919780

X 40

Bottom Frame Connector

T608960

X 4

Mattress Retainer

T605640

X 2

Hook

T391180

X 3

Plastic Plug

T392590

X 124

Slat Space 01

T919480

X 22

Slat Space 02

T919490

X 21

Z

K

O

Q

W

Y

T

U

S

L

R

L

R

Mechanism 1

T605570

X 1

Mechanism 2

T605560

X 1

6

Hardware Pack

B34410501900

Hardware Pack #: T4105019-00

Hardware Note:

Please do not completely tighten all the hardware,

until the entire assembly is complete, unless

otherwise indicated in the step-by-step

instructions.

6

7

8

4

5

3

2

1

1/4" X 2 3/8"

X 8

1/4" X 1 3/4"

X 4

1/4" X 1 3/8"

X 8

1/4" X 1 3/16"

X 12

5/16" X 3/4"

X 8

1/4" X 3/4"

X 24

1/4"

X 20

1/4"

X 8

9

11

4mm

X 1

Wrench

X 1

A

B

7

B34410501900

Step

1

1.1 Slide (A) & (B) into (X1), then fasten

with BOLTS 6.

1.2 Attach (I2) to (A) & (B) with BOLTS 1

and WASHER 8.

X 4

A

B

I2

X1

A

I2

1.1

1.2

1

X 2

6

X 4

8

6

1

8

C

D

8

B34410501900

Step

2

2.1 Slide (A) & (B) into (M), then fasten

with BOLTS 6.

2.2 Attach (I1) to (A) & (B) with BOLTS 1

and WASHER 8.

X 4

A

B

I1

M

A

M

B

I1

2.1

2.2

1

6

8

X 2

X 4

6

8

1

E

9

B34410501900

Step

3

Attach (E) X 2 to (M) & (X1) with BOLTS 6

and BOLTS 2 .

X 4

A

B

A

B

E

M

X1

2

X 4

6

2

6

F

10

B34410501900

Step

4

Attach (F1) & (H) to (A) & (B) with BOLTS

5.

X 8

A

B

A

B

H

F1

B

F1

5

11

B34410501900

Step

5

5.1 Slide (O) into the slots on (E).

5.2 Lock (O) into place with (Y).

E

O

2

1

2

3

1

E

O

Y

5.1

5.2

12

B34410501900

Step

6

6.1 Press (W) onto (O) approximately in

the middle, as illustrated;

6.2 Press (Q) onto (W) alternating left and

right.

O

W

Q

6.1

6.2

G

H

13

B34410501900

Step

7

7.1 Attach (Z) to (X1) with BOLTS 4 and

NUTS 7.

7.2 Attach (Z) to (I2) with BOLTS 4 and

NUTS 7.

Repeat this step for the other side.

X 8

I2

I1

X1

M

Z

X1

Z

I2

7.1

7.2

4

X 8

7

4

7

J

14

B34410501900

Step

8

Attach (R) & (L) to (I1) & (I2) with BOLTS 4

and NUTS 7.

X 4

I1

R

I2

L

I1

R

4

7

X 4

For your safety, please ensure (L & R)

are mounted on corresponding

location as specified in drawing.

K

L

M

15

B34410501900

Step

9

N

X

E1

S

N

X

N

X

S

E1

9.1

9.2

9.3

X 8

6

9.1 Place (X) on top of (N).

9.2 Insert (S) X 2 into (N) and secure

with BOLTS 6 as shown.

9.3 Insert (E1) into (S) and secure with

BOLTS 6 as shown.

Wide side of the slot should

be facing up !

N

P

16

B34410501900

Step

10

N

V

S

N

S

10.1

10.2

6

X 8

10.1 Insert (S) X 2 into (V) and secure

with BOLTS 6.

10.2 Insert (N) into (S) and secure with

BOLTS 6.

Wide side of the slot should

be facing up !

17

B34410501900

Step

11

BACKREST

SEAT FRAME

V

N

E1

K

1

2

3

2

3

V

K

V

K

Y

11.1 Slide (K) into the slots on (V) & (N) &

(E1).

11.2 Lock (K) into place with (Y).

11.1

11.2

R

18

B34410501900

Step

12

N

L

R

N

R

X 4

3

7

X 4

7

Attach (N) to (R) & (L) with BOLTS 3 and

NUTS 7.

In order to perfectly align the Locking

Mechanism on part E1 with the Pin on

part F1, please do not completely

tighten the bolts 3 until next step is

completed.

E1

19

B34410501900

Step

13

E1

F1

E1

F1

Lift the SEAT FRAME to futon position and

lock the mechanism on part E1 with the pin

on part F1 as shown, then completely

tighten all bolts 3.

V

20

B34410501900

Step

14

V

R

L

N

R

3

7

X 4

3

7

Attach (N) on BACKREST to (R) & (L) with

BOLTS 3 and NUTS 7.

W

AA

21

B34410501900

Step

15

E1

T

E1

T

E1

T Attach (T) X 2 to E1 where indicated.

Page is loading ...

Dorel Home 4105419 Owner's manual

This manual is also suitable for

Dorel Home 4105419 Owner's manual

in other languages

Related papers

Other documents