2. Bintronic
  3. Motorized Smart Zebra Shades
Motorized Smart Zebra Shades

Bintronic Motorized Smart Zebra Shades User manual

  • Hello! I have reviewed the instruction manual for the Bintronic Zebra Shade. This document provides detailed instructions on how to set up the shades, including adjusting upper and lower limits, light filtering settings, and adding additional remote controls. I can answer questions about the setup, operation, and maintenance of your motorized smart Zebra Shades.
  • How do I set the upper limit?
    How do I add another remote control unit?
    How do I clear off the password?
How to open Battery Compartment Cover
Motorized/Smart Zebra Shades
Instruction Manual
P1
BINTRONIC ENTERPRISE CO., LTD
No.62, Bengong 5th Rd., Gangshan Dist., Kaohsiung City 82059, Taiwan (R.O.C.)
Email: [email protected]
This instruction manual version is v1.0.
All Rights Reserved.
Copyright © 2022 Bintronic Enterprise
1-1 Setting or modifying position of Upper-Limit
1-2 Setting or modifying position of Lower-Limit
1-3 Setting of Light Filtering Position
1-4 Setting of Auto Light Filtering
2-1 Adding another Remote Control Unit
3-1 Alter direction of Zebra Shade movement
4-1 Clear off Password
5-1 Externally connected Manual Switch Box
6-1 Battery Replacement
6-2 Product Specifications
6-3 Quick Setting Index
6-4 Instructions for using Remote Control Holder
UP
STOP
RIGHTWARD
LIGHT FILTERING
UPWARD
LIGHT FILTERING
DOWN
Push the cover out
Insert latches into
corresponding slots
Place Battery
Compartment Cover
to engage it with Slides
1 2 3
Insert latches
How to replace Battery Compartment Cover
Push the cover in
making settings
Key check-points prior to When setting Upper-/Lower-Limit points,
set Upper-Limit first, then the Lower-Limit.
STEP-1
1 2
1-1 Setting or modifying position of Upper-Limit
STEP-1
First, make sure if the direction of movement is correct. Verify if the Zebra Shade moves upwards
by pressing [UP] and downwards by pressing [DOWN]. After that, carry out setting or modification
of Upper-/Lower-Limit points. In case the Zebra Shade moves in the opposite direction, refer to
the Steps of Item 3-1 in Table of Contents to correct the direction.
Press [SET] + [UP] keys until the Motor
makes a twitch, indicating the setting mode
of Upper-Limit is activated.
STEP-1
STEP-2 Press [UP] or [DOWN] key to move the Zebra Shade to a pre-determined position,
to be set as the Upper-Limit.
back
the Motor will make a twitch
When the Motor makes a
twitch, the Zebra Shade will
move upwards and
downwards at the same time
as a response.
While the Shade is getting close to reaching
the Upper-Limit, please press [STOP] to stop
the movement to avoid damage to the motor.
Then, tap to fine tune to the place where you
would like it to be set up as the Upper-Limit.
press [STOP] and tap
to fine tune to the
Upper-Limit
Tap to fine tune. Press for 2 seconds,
and it will move continuously.
CAUTION
Motorized/Smart Zebra Shades
Instruction Manual
P2
BINTRONIC ENTERPRISE CO., LTD
No.62, Bengong 5th Rd., Gangshan Dist., Kaohsiung City 82059, Taiwan (R.O.C.)
Email: [email protected]
This instruction manual version is v1.0.
All Rights Reserved.
Copyright © 2022 Bintronic Enterprise
1-2 Setting or modifying position of Lower-Limit
STEP-1
STEP-3 When the pre-determined position is reached, press [STOP] key once to stop the movement; press any
of the keys [UPWARD LIGHT FILTERING] or [DOWNWARD LIGHT FILTERING] + [SET] to confirm;
the setting is completed when Motor makes a twitch.
STEP-1
STEP-3 When the pre-determined position is reached, press [STOP]
key once to stop the movement; press any of the keys
[UPWARD LIGHT FILTERING] or [DOWNWARD LIGHT
FILTERING] + [SET] to confirm; the setting is completed
when Motor makes a twitch.
STEP-1
STEP-1 Press [SET] + [DOWN] keys until Motor makes a twitch,
indicating that the setting mode of Lower-Limit is activated.
STEP-1
STEP-2 Press [UP] or [DOWN] key to move the Zebra Shade to a
pre-determined position, to be set as the Lower-Limit.
The motor makes a twitch.
press [STOP] press 1 of the keys + [SET]
When the Motor makes a
twitch, the Zebra Shade will
move upwards and
downwards at the same time
as a response.
When all procedures are done, the Upper-Limit
setting is completed, too. And the setting of
Lower-Limit has been cleared as well.
back
the Motor will make a twitch
reach to the Lower-Limit
When the Motor makes a
twitch, the Zebra Shade will
move upwards and
downwards at the same time
as a response.
When the Motor makes a
twitch, the Zebra Shade will
move upwards and
downwards at the same time
as a response.
Tap to fine tune. Press for 2 seconds,
and it will move continuously.
When entering the Lower-Limit position
setting mode, the mode will be deactivated if
no keys are pressed within 5 seconds. Plus,
previous setting will not be recorded. Please
go back to STEP-1 and reset it.
The motor makes a twitch.
press [STOP] press 1 of the keys + [SET]
Setting Completed
When all procedures are done, the
Lower-Limit setting is completed, too.
CAUTION
Setting Completed
Motorized/Smart Zebra Shades
Instruction Manual
P3
BINTRONIC ENTERPRISE CO., LTD
No.62, Bengong 5th Rd., Gangshan Dist., Kaohsiung City 82059, Taiwan (R.O.C.)
Email: [email protected]
This instruction manual version is v1.0.
All Rights Reserved.
Copyright © 2022 Bintronic Enterprise
STEP-1
STEP-1 Press [SET] + [DOWN] keys until Motor makes a twitch;
then, press [SET] + [DOWN] keys again until Motor makes
another twitch, indicating that the setting mode of Light
Filtering Position is activated.
STEP-1
STEP-2 Press [UP] or [DOWN] key to move the Zebra Shade to a pre-determined position,
to be set as the Light Filtering Position.
back
the Motor will make a twitchpress [SET] + [DOWN] twice
When the Motor makes a
twitch, the Zebra Shade will
move upwards and
downwards at the same time
as a response.
STEP-1
STEP-3 When the pre-determined position is reached, press the
[STOP] key once to stop the movement; press either of
the keys [UPWARD LIGHT FILTERING] or [DOWN-
WARD LIGHT FILTERING] + [SET] to confirm; the
setting is completed when the Motor makes a twitch.
When the Motor makes a
twitch, the Zebra Shade will
move upwards and
downwards at the same time
as a response.
The motor makes a twitch.
press [STOP] press 1 of the keys + [SET]
When all procedures are done, the Light
Filtering Position setting is completed, too.
1-3 Setting of Light Filtering Position
Do not press any key within 5 seconds; and then press
[STOP] to return to the full light transmittance mode
from any position.
1-4 Setting of Auto Light Filtering
Tap to fine tune. Press for 2 seconds,
and it will move continuously.
press [STOP] after 5 seconds, the Zebra Shade
will close automatically and return to the full
light transmittance mode
When entering the Light Filtering
Position setting mode, the mode
will be deactivated if no keys are
pressed within 5 seconds. Plus,
previous setting will not be
recorded. Please go back to
STEP-1 and reset it.
reach to the
Light Filtering
Position
CAUTION
Setting Completed
Motorized/Smart Zebra Shades
Instruction Manual
P4
BINTRONIC ENTERPRISE CO., LTD
No.62, Bengong 5th Rd., Gangshan Dist., Kaohsiung City 82059, Taiwan (R.O.C.)
Email: [email protected]
This instruction manual version is v1.0.
All Rights Reserved.
Copyright © 2022 Bintronic Enterprise
STEP-1
STEP-2 Now press [STOP] key of the Remote Control to be added; the adding
process is completed when the Motor makes a twitch.
When all procedures are done,
please do not press any key and
wait for 5 seconds until the
Motor makes a twitch, indicating
that the setting is completed.
STEP-1
STEP-1 Press and hold [SET] + [STOP] until the Motor makes a
twitch, indicating that the setting mode of Adding another
Remote Control Unit is activated.
2-1 Adding another Remote Control Unit
STEP-1
STEP-1 Press [SET] + [STOP] keys until the Motor makes a twitch,
indicating that the setting mode of Altering direction of
Zebra Shade is activated.
3-1 Alter direction of Zebra Shade
back
the Motor will make a twitch the Motor will make a twitch
When the Motor makes a
twitch, the Zebra Shade will
move upwards and
downwards at the same time
as a response.
back
the Motor will make a twitch
When the Motor makes a
twitch, the Zebra Shade will
move upwards and
downwards at the same time
as a response.
When the Motor makes a
twitch, the Zebra Shade will
move upwards and
downwards at the same time
as a response.
STEP-1
STEP-2 Now press [UP] + [STOP] + [DOWN] keys all together, the Motor will
rotate in reverse direction; press [UP] + [STOP] + [DOWN] keys all
together again, the Motor will rotate in forward direction.
the Motor rotates in forward
direction for the 2nd time
When all procedures are done,
please do not press any key and
wait for 5 seconds until the
Motor makes a twitch, indicating
that the setting is completed.
Setting Completed
Setting Completed
the Motor rotates in reverse
direction for the 1st time
Motorized/Smart Zebra Shades
Instruction Manual
P5
BINTRONIC ENTERPRISE CO., LTD
No.62, Bengong 5th Rd., Gangshan Dist., Kaohsiung City 82059, Taiwan (R.O.C.)
Email: [email protected]
This instruction manual version is v1.0.
All Rights Reserved.
Copyright © 2022 Bintronic Enterprise
the Motor makes a twitch forward
and backward
When all the procedures are
done, only the password of this
remote remains, others will be
erased. If a new password is
not added, the old password
will not be erased.
When the Motor makes a
twitch, the Zebra Shade will
move upwards and
downwards at the same time
as a response.
STEP-1
STEP-1 Unplug power supply of the Motor, wait for 15 seconds, resume power
supply of it. Press [UP] + [STOP] + [DOWN] + either of the keys
[UPWARD LIGHT FILTERING] or [DOWNWARD LIGHT FILTERING]
altogether 4 keys within 8 seconds until the Motor makes a twitch.
STEP-1
STEP-2 After Motor makes a twitch, simultaneously press [UP] +
[DOWN] keys of the Remote Control within 8 seconds;
password is cleared off when the Motor makes a twitch.
4-1 Clear off Password
5-1 Externally connected Manual Switch Box
unplug power supply wait for 15 seconds resume power supply press 4 keys altogether within 8 seconds the Motor makes a twitch
forward and backward
When the Motor makes a
twitch, the Zebra Shade will
move upwards and
downwards at the same time
as a response.
yellow
red
brown
green
System Manual Switch
A brief contact will activate the function;
DO NOT short-circuit continuously.
Green: Common
Brown: Up
Red: Stop
Yellow: Down
Manual Switch Function (code 2680 Type, code 2240 Type):
UP
STOP
DOWN
Press [UP] shortly, the full light transmittance mode of the Zebra Shade will be activated.
Press [UP] for 1 second, the Zebra Shade will be opened completely.
Press [STOP] shortly, the Zebra Shade will stop immediately.
When the Zebra Shade is fully closed, press [STOP] shortly,
the full light transmittance mode of the Zebra Shade will be activated.
When the full light transmittance mode is activated, press [STOP] for 1 second,
the Zebra Shade will be closed completely.
When the Zebra Shade is fully opened, press [STOP] for 1 second,
the Zebra Shade will be closed completely.
Press [CLOSE] shortly, the full light transmittance mode will be deactivated.
Press [CLOSE] for 1 second, the Zebra Shade will be closed completely.
(When the Zebra Shade is moving, press the key of another direction, it will stop immediately.)
1
2
1
2
1
2
3
4
Setting Completed
It’s the same as step 1-1 to 1-3.
Motorized/Smart Zebra Shades
Instruction Manual
P6
BINTRONIC ENTERPRISE CO., LTD
No.62, Bengong 5th Rd., Gangshan Dist., Kaohsiung City 82059, Taiwan (R.O.C.)
Email: [email protected]
This instruction manual version is v1.0.
All Rights Reserved.
Copyright © 2022 Bintronic Enterprise
6-1 Battery Replacement 6-2 Product Specifications
6-3 Quick Setting Index
6-4 Instructions for using Remote Control Holder
Completed.
1 2
With flat side (positive +) of the Battery
facing upwards, making sure that the
Battery is latched up by two spring plates,
insert Battery in a slanted angle to enter it
into the Battery Holder.
flat side (positive +)
latched up by two
spring plates
Battery: CR2450 3V (One-time type lithium battery)
Dimensions: L 13CM, W 4.8CM, H 1.1CM
Standby Current: <1uA
Modulation Method: OOK
Encoding Method: Internally-burnt fixed coding
Transmission Frequency: 433.92MHz
Antenna Type: on board, Gain=0 dbi
Weight (including battery): 66g
Upper-Limit Setting: [SET]+ [UP] Lower-Limit Setting: [SET]+ [DOWN]
Setting of Light Filtering Position: [SET]+ [DOWN] *twice Setting of Auto Light Filtering: do not press any key for 5 seconds, and then press [STOP]
Add another Remote Control: (Original Remote Control) [SET] + [STOP], (Remote Control 2) [STOP]
Alter direction of Zebra Shade movement: [SET] + [STOP], [UP] + [STOP] + [DOWN] (reverse direction), [UP] + [STOP] + [DOWN] (forward direction)
Clear off Password: [UP] + [STOP] + [DOWN] + either [UPWARD LIGHT FILTERING] or [DOWNWARD LIGHT FILTERING] key, [UP] + [DOWN].
Vertical Holder
Wall-mount Holder
Open-up support plate on
the back for the use as a
vertical holder.
open up
Apply the provided double-face
adhesive tape on the back of
Holder and stick it onto the
desired position on the wall, as
a wall-mounted holder.
Apply the adhesive tape
stick it onto the
desired position
/