Kvaser Mini PCI Express 2xHS v2 User’s Guide
Copyright 2017-2022 Kvaser AB, Mölndal, Sweden
https://www.kvaser.com
Printed Thursday 8th September, 2022
We believe that the information contained herein was accurate in all respects at the time of printing.
Kvaser AB cannot, however, assume any responsibility for errors or omissions in this text. Also note
that the information in this document is subject to change without notice and should not be construed
as a commitment by Kvaser AB.
Kvaser Mini PCI Express 2xHS v2 User’s Guide 3 (17)
Contents
1 About this manual 4
2 Introduction 5
2.1 Welcome to Kvaser Mini PCI Express 2xHS v2 . . . . . . . . . . . . 5
2.2 Major features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.3 Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.4 Additional software and documentation . . . . . . . . . . . . . . . . 6
3 Kvaser Mini PCI Express 2xHS v2 hardware 7
3.1 Hardware installation . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3.2 Mini PCI Express connection . . . . . . . . . . . . . . . . . . . . . . 7
3.3 CAN channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3.4 Power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3.5 LED Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3.6 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
4 Appendices 9
4.1 Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
4.2 CAN connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
4.3 CAN bus termination . . . . . . . . . . . . . . . . . . . . . . . . . . 10
4.4 Updating the firmware . . . . . . . . . . . . . . . . . . . . . . . . . . 10
5 Disposal and Recycling Information 12
6 Legal acknowledgements 13
6.1 Usage warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
6.2 EU Regulatory Compliance . . . . . . . . . . . . . . . . . . . . . . . 14
6.3 FCC Regulatory Compliance . . . . . . . . . . . . . . . . . . . . . . 15
6.4 Patents, Copyrights and Trademarks . . . . . . . . . . . . . . . . . . 16
7 Document Revision History 17
Kvaser AB, Mölndal, Sweden — www.kvaser.com
Kvaser Mini PCI Express 2xHS v2 User’s Guide 4 (17)
1 About this manual
This manual is intended for Kvaser Mini PCI Express 2xHS v2 users. This
document contains a description of the hardware’s properties and general
instructions for connecting the device to a computer.
Kvaser AB, Mölndal, Sweden — www.kvaser.com
Kvaser Mini PCI Express 2xHS v2 User’s Guide 5 (17)
2 Introduction
This section will describe the functions and features of the Kvaser Mini PCI
Express 2xHS v2.
2.1 Welcome to Kvaser Mini PCI Express 2xHS v2
Figure 1: Kvaser Mini PCI Express 2xHS v2
Kvaser Mini PCI Express 2xHS v2 is a small, yet advanced, CAN multi-channel
real time CAN interface that handles transmission and reception of standard and
extended CAN messages on the bus with a high time stamp precision. The Kvaser
Mini PCI Express 2xHS v2 is compatible with applications that use Kvaser‘s
CANlib.
This guide applies to Kvaser Mini PCI Express 2xHS v2 devices listed in Table 1.
Device Product Number (EAN)
Kvaser Mini PCI Express 2xHS v2 73-30130-01029-1
Table 1: Kvaser Mini PCI Express 2xHS v2 devices and their product numbers.
Kvaser AB, Mölndal, Sweden — www.kvaser.com
Kvaser Mini PCI Express 2xHS v2 User’s Guide 6 (17)
2.2 Major features
•Fully compliant to the PCIe bus specification 1.2, type F2 form factor
(Full-Mini with bottom-side keep outs).
•Supports both 11-bit (CAN 2.0A) and 29-bit (CAN 2.0B active) identifiers.
•High-speed CAN connection (compliant with ISO 11898-2), up to 1 Mbit /s.
•Supports CAN FD, up to 8 Mbit/s (with correct physical layer implementation).
•100 % compatible with applications written using Kvaser CANlib targeting
other Kvaser CAN hardware.
•Fully compatible with J1939, CANopen, NMEA 2000 and DeviceNet.
•Supports silent mode for analysis tools – listen to the bus without interfering.
2.3 Interface
Kvaser Mini PCI Express 2xHS v2 provides a CAN bus interface through the PCIe
system bus in a mPCIe slot.
2.4 Additional software and documentation
The Kvaser CANlib SDK includes everything you need in order to develop software
applications interacting with Kvaser CAN and LIN hardware. The SDK contains full
documentation and many sample programs, written in C, C++, C#, Delphi, Python
and Visual Basic. Kvaser CAN and LIN hardware is built around the same common
software API. Applications developed using one device type will run without
modification on other device types.
The latest versions of documentation, software and drivers can be downloaded for
free at www.kvaser.com/download.
Kvaser AB, Mölndal, Sweden — www.kvaser.com
Kvaser Mini PCI Express 2xHS v2 User’s Guide 7 (17)
3 Kvaser Mini PCI Express 2xHS v2 hardware
In this section you can read more about the CAN channels and power supply.
3.1 Hardware installation
The Kvaser Mini PCI Express 2xHS v2 may be inserted in any free Mini PCI
Express slot with PCIe on the host computer. You do need to switch the power off
before inserting or removing the device. For the Kvaser Mini PCI Express 2xHS v2
to communicate with the host computer, compatible versions of the Kvaser driver
and firmware must be used. The firmware is downloaded and installed directly on
the Kvaser Mini PCI Express 2xHS v2. The driver is installed on the host computer.
The latest version of the drivers, , and firmware can
be downloaded from www.kvaser.com/download.
3.2 Mini PCI Express connection
The Kvaser Mini PCI Express 2xHS v2 is a card of type F2 (Full-Mini with bottom
side keep outs).
Figure 2: Mini PCI Express connector on Kvaser Mini PCI Express 2xHS v2
3.3 CAN channels
The Kvaser Mini PCI Express 2xHS v2 has two CAN channels in a single 7-pin
Molex connector (see Figure 3 on Page 8). See Section 4.2, CAN connectors, on
Page 9 for pinout information.
Kvaser AB, Mölndal, Sweden — www.kvaser.com
Kvaser Mini PCI Express 2xHS v2 User’s Guide 8 (17)
Figure 3: CAN connector on Kvaser Mini PCI Express 2xHS v2
3.4 Power supply
The Kvaser Mini PCI Express 2xHS v2 is only powered using +3.3 V from the Mini
PCI Express connector.
3.5 LED Indicators
The Kvaser Mini PCI Express 2xHS v2 has no LED indicators.
3.6 Troubleshooting
Use “Kvaser Device Guide” in the Control Panel to verify that the computer can
communicate with the Kvaser Mini PCI Express 2xHS v2. If the firmware version
shown is all zeros, there are communication problems.
Kvaser AB, Mölndal, Sweden — www.kvaser.com
Kvaser Mini PCI Express 2xHS v2 User’s Guide 9 (17)
4 Appendices
In this section you will find technical information about the Kvaser Mini PCI Express
2xHS v2 and its connectors.
4.1 Technical data
In Table 2 below you will find the technical specifications of Kvaser Mini PCI
Express 2xHS v2.
CAN Channels 2
CAN Transceivers MCP2561FD (Compliant with ISO 11898-2)
CAN Controller Kvaser CAN IP in FPGA
Galvanic isolation Yes
CAN Bit Rate 50 kbit/s to 1 Mbit/s “Classic CAN”
CAN FD Bit Rate Up to 8 Mbit/s (with correct physical layer implementation)
Time stamp resolution 1 µs
Max message rate 20000 msg/s per channel
Error Frame Detection Yes
Error Frame Generation Yes
Silent mode Yes
Kvaser CANtegrity No
Host interface PCIe system bus in a mPCIe slot, type F2 (i.e. full-Mini with bottom
side keep outs)
Host OS Windows (7 or later), Linux.
Power consumption Typically 700 mW idle plus max 150 mW per channel, i.e. max
1000 mW for a two channel interface. Only uses 3.3 V.
Hardware configuration Done by software.
Dimensions 51 x 30 x 5 mm
Weight 6 g (21 g including splitter cable)
Operating temperature −40 ◦C to +85 ◦C
Storage temperature −40 ◦C to +85 ◦C
Relative humidity 0 % to 85 % (non-condensing.)
Table 2: Technical Specifications.
4.2 CAN connectors
Kvaser Mini PCI Express 2xHS v2 devices that use the 7-pin Molex connector
(53780-0770) have the pinning described in Table 3 on Page 10.
Kvaser AB, Mölndal, Sweden — www.kvaser.com
Kvaser Mini PCI Express 2xHS v2 User’s Guide 10 (17)
Figure 4: Molex Connector 53780-0770
Molex pin number Function
1 GND channel 1
2 CAN_L channel 1
3 CAN_H channel 1
4 Shield
5 CAN_L channel 2
6 CAN_H channel 2
7 GND channel 2
Table 3: Molex pin configuration
4.3 CAN bus termination
Every CAN bus must be terminated with a 120 Ohm resistor at each end of the
bus. The Kvaser Mini PCI Express 2xHS v2 does not contain any CAN bus
termination, because their inclusion could cause severe disturbance in a system
which is already correctly terminated.
For laboratory or testing use, the exact value of the termination resistors is not
always critical. Sometimes a single terminator is sufficient. For production, proper
termination is essential. If you see error frames on the bus, you should check the
termination.
To save yourself a lot of trouble, always terminate the CAN
bus properly.
4.4 Updating the firmware
For the Kvaser Mini PCI Express 2xHS v2 to communicate with the host computer,
compatible versions of the Kvaser CANlib (including driver) and firmware must be
installed.
The latest versions of firmware and drivers can be downloaded for free at
www.kvaser.com/download.
Connect the Kvaser Mini PCI Express 2xHS v2 to your host computer
Kvaser AB, Mölndal, Sweden — www.kvaser.com
Kvaser Mini PCI Express 2xHS v2 User’s Guide 11 (17)
and start the update.exe application. A window opens showing the Firmware
Update Instructions, read and follow those carefully.
To check the current firmware version, open “Kvaser Device Guide” which can be
found in the Control Panel. Select “Kvaser Mini PCI Express 2xHS v2” in the tree
view to the left, and click on the channel. The firmware revision information now
appears in the right half of the window.
Kvaser AB, Mölndal, Sweden — www.kvaser.com
Kvaser Mini PCI Express 2xHS v2 User’s Guide 12 (17)
5 Disposal and Recycling Information
When this product reaches its end of life, please dispose of it
according to your local environmental laws and guidelines.
For information about Kvaser’s recycling programs, visit:
https://www.kvaser.com/en/kvaser/recycling-policy.html
Kvaser AB, Mölndal, Sweden — www.kvaser.com
Kvaser Mini PCI Express 2xHS v2 User’s Guide 13 (17)
6 Legal acknowledgements
6.1 Usage warning
WARNING FOR ALL USERS
WARNING! - YOUR USE OF THIS DEVICE MUST BE DONE WITH CAUTION AND A FULL
UNDERSTANDING OF THE RISKS!
THIS WARNING IS PRESENTED TO INFORM YOU THAT THE OPERATION OF THIS DEVICE
MAY BE DANGEROUS. YOUR ACTIONS CAN INFLUENCE THE BEHAVIOR OF A CAN-BASED
DISTRIBUTED EMBEDDED SYSTEM, AND DEPENDING ON THE APPLICATION, THE
CONSEQUENCES OF YOUR IMPROPER ACTIONS COULD CAUSE SERIOUS OPERATIONAL
MALFUNCTION, LOSS OF INFORMATION, DAMAGE TO EQUIPMENT, AND PHYSICAL
INJURY TO YOURSELF AND OTHERS. A POTENTIALLY HAZARDOUS OPERATING
CONDITION IS PRESENT WHEN THE FOLLOWING TWO CONDITIONS ARE
CONCURRENTLY TRUE: THE PRODUCT IS PHYSICALLY INTERCONNECTED TO A REAL
DISTRIBUTED EMBEDDED SYSTEM; AND THE FUNCTIONS AND OPERATIONS OF THE
REAL DISTRIBUTED EMBEDDED SYSTEM ARE CONTROLLABLE OR INFLUENCED BY THE
USE OF THE CAN NETWORK. A POTENTIALLY HAZARDOUS OPERATING CONDITION MAY
RESULT FROM THE ACTIVITY OR NON-ACTIVITY OF SOME DISTRIBUTED EMBEDDED
SYSTEM FUNCTIONS AND OPERATIONS, WHICH MAY RESULT IN SERIOUS PHYSICAL
HARM OR DEATH OR CAUSE DAMAGE TO EQUIPMENT, DEVICES, OR THE SURROUNDING
ENVIRONMENT.
WITH THIS DEVICE, YOU MAY POTENTIALLY:
•CAUSE A CHANGE IN THE OPERATION OF THE SYSTEM, MODULE, DEVICE,
CIRCUIT, OR OUTPUT.
•TURN ON OR ACTIVATE A MODULE, DEVICE, CIRCUIT, OUTPUT, OR FUNCTION.
•TURN OFF OR DEACTIVATE A MODULE, DEVICE, CIRCUIT, OUTPUT, OR
FUNCTION.
•INHIBIT, TURN OFF, OR DEACTIVATE NORMAL OPERATION.
•MODIFY THE BEHAVIOR OF A DISTRIBUTED PRODUCT.
•ACTIVATE AN UNINTENDED OPERATION.
•PLACE THE SYSTEM, MODULE, DEVICE, CIRCUIT, OR OUTPUT INTO AN
UNINTENDED MODE.
ONLY THOSE PERSONS WHO:
(A) ARE PROPERLY TRAINED AND QUALIFIED WITH RESPECT TO THE USE OF THE
DEVICE,
(B) UNDERSTAND THE WARNINGS ABOVE, AND
(C) UNDERSTAND HOW THIS DEVICE INTERACTS WITH AND IMPACTS THE FUNCTION
AND SAFETY OF OTHER PRODUCTS IN A DISTRIBUTED SYSTEM AND THE APPLICATION
FOR WHICH THIS DEVICE WILL BE APPLIED, MAY USE THE DEVICE.
PLEASE NOTE THAT YOU CAN INTEGRATE THIS PRODUCT AS A SUBSYSTEM INTO
HIGHER-LEVEL SYSTEMS. IN CASE YOU DO SO, KVASER AB HEREBY DECLARES THAT
KVASER AB’S WARRANTY SHALL BE LIMITED TO THE CORRECTION OF DEFECTS, AND
KVASER AB HEREBY EXPRESSLY DISCLAIMS ANY LIABILITY OVER AND ABOVE THE
REFUNDING OF THE PRICE PAID FOR THIS DEVICE, SINCE KVASER AB DOES NOT HAVE
ANY INFLUENCE ON THE IMPLEMENTATIONS OF THE HIGHER-LEVEL SYSTEM, WHICH
MAY BE DEFECTIVE.
Kvaser AB, Mölndal, Sweden — www.kvaser.com
Kvaser Mini PCI Express 2xHS v2 User’s Guide 14 (17)
6.2 EU Regulatory Compliance
Company Name:
Postal address:
Postcode:
City:
Telephone number:
E-mail address:
Product:
EU Declaration of Conformity (DoC)
We
Kvaser AB
Aminogatan 25
431 53
M¨olndal
+46 31 886344
sales@kvaser.com
declare that the DoC is issued under our sole responsibility and belongs to the following product:
Kvaser Mini PCI Express 2xHS v2
Object of the declaration (identification of apparatus allowing traceability):
Product: Kvaser Mini PCI Express 2xHS v2
Type: 73-30130-01029-1
The object of the declaration described above is in conformity with the relevant Union harmonisation
legislation:
Electromagnetic Compatibility (EMC) Directive 2014/30/EU (Art. 6)
RoHS recast Directive 2011/65/EU (Art. 4.1)
The following harmonised standards and technical specifications have been applied
(title, date of standard/specification):
EN 55024 (2010) EN 55032 (2012)
EN 61000-6-2 (2005) EN 61000-6-3 (2007 + A1:2011)
EN 50581 (2012)
Signed for and on behalf of:
M¨olndal
Place of issue
2019-12-05
Date of issue Claes Haglund, Supply Chain and Quality director
Kvaser AB, Mölndal, Sweden — www.kvaser.com
Kvaser Mini PCI Express 2xHS v2 User’s Guide 15 (17)
6.3 FCC Regulatory Compliance
Federal Communications Commission (FCC) Compliance Information Statement
IDENTIFICATION OBJECT:
Product: Kvaser Mini PCI Express 2xHS v2
Type: 73-30130-01029-1
APPLICABLE COMPLIANCE STATEMENTS:
CFR Title 47 Part 15 §15.107, §15.109
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired operation.
RESPONSIBLE PARTY (IN USA) NAME:
Kvaser Inc.
23881 Via Fabricante, Suite 503
Mission Viejo, CA 92691
Internet contact: [email protected]
Kvaser AB, Mölndal, Sweden — www.kvaser.com
Kvaser Mini PCI Express 2xHS v2 User’s Guide 16 (17)
6.4 Patents, Copyrights and Trademarks
All trademarks are the property of their respective owner. Windows is a registered
trademark of Microsoft Corporation in the United States and other countries.
Adobe, the Adobe logo, and Reader are either registered trademarks or trademarks
of Adobe Systems Incorporated in the United States and/or other countries.
MagiSync is a trademark of Kvaser AB.
DeviceNet is a trademark of Open DeviceNet Vendor Association, Inc.
NMEA 2000 is the registered trademark of the National Marine Electronics
Association, Inc.
For information about Kvaser related CAN patents, see www.kvaser.com/patent.
Kvaser AB, Mölndal, Sweden — www.kvaser.com
Kvaser Mini PCI Express 2xHS v2 User’s Guide 17 (17)
7 Document Revision History
Version history for document UG_98203_minipciexpress_2hs_v2:
Revision Date Changes
1.0 2018-10-15 Initial version
1.1 2019-02-11 Minor textual changes
1.2 2019-08-09 Url protocol updated
1.3 2020-01-27 Added sdoc
1.4 2020-08-19 Updated supported OS
1.5 2021-09-09 Dropped mention of Hi-Speed CAN
1.6 2022-04-01 Minor textual changes
Kvaser AB, Mölndal, Sweden — www.kvaser.com
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Kvaser Mini PCI Express 2xHS User guide
-
-
-
-
-
-
-
-
-