Laufen 9505792 Technical Guide

Laufen
Brand
Laufen
Model
9505792
Type
Technical Guide

Laufen 9505792 is a mixer that can be used in domestic, hotel, and commercial settings. It has a chrome finish and is suitable for use with storage tank and continuous flow hot water units. The maximum continuous operating pressure is 1000kPa, but for best performance and longer life, it is recommended to use between 150-500kPa. Hot and cold water inlet pressure should be equal. The maximum continuous working temperature is 80°C. The mixer comes factory assembled and tested, and it is not recommended to dismantle any internal parts.

Laufen 9505792 is a mixer that can be used in domestic, hotel, and commercial settings. It has a chrome finish and is suitable for use with storage tank and continuous flow hot water units. The maximum continuous operating pressure is 1000kPa, but for best performance and longer life, it is recommended to use between 150-500kPa. Hot and cold water inlet pressure should be equal. The maximum continuous working temperature is 80°C. The mixer comes factory assembled and tested, and it is not recommended to dismantle any internal parts.

SIMIBOX LIGHT W/O SHUT-OFF
To see the complete LAUFEN range go to
www.reece.com.au/bathrooms
LAUFEN
Disclaimer: Products in this specification manual must by regulation be installed by licensed and registered trade
people. The manufacturer/distributor reserves the right to vary specifications or delete models from their range without
prior notification. Dimensions are nominal measurements only. Dimensions and set-outs listed are correct at time of
publication however the manufacturer/distributor takes no responsibility for printing errors.
Tech Page Version 1
CLEANING RECOMMENDATIONS
We recommend the use of soapy water or approved cleaners.
This product should not be cleaned with abrasive materials.
Damage caused by any improper treatment is not covered by the product warranty. Refer to Warranty Conditions.
Dimensions are nominal measurements only.
TM
WMK25894
AS/NZS 3718
SPECIFICATIONS
Recommended use Domestic, Hotel and Commercial
Colour availability Chrome
Pressure rating Maximum continuous operating pressure 1000kPa.
As per AS/NZS3500 pressure must be limited to
500kPa on any new home, extension or renovation.
For best performance and longer life we recommend
150-500kPa.
Hot and cold water inlet pressure should be equal.
Temperature rating Maximum continuous working temperature 80°C
Suitable Hot Water
Units
Storage Tank: Yes
Continuous Flow: Yes
Gravity Feed: Not suitable
page 1 of 7
LAUFEN
Plumbers, please ensure a copy of the installation
instructions is left with the end user for future reference
Important Note
Mixer must be installed to the requirements of AS/NZS 3500 by a qualified plumber. Your mixer comes to you already factory
assembled and tested. We do not recommend the dismantling of any internal part of the mixer. The mixers are factory tested and
sealed so as to give the best performance.
SIMIBOX LIGHT W/O SHUT-OFF
INSTALLATION INSTRUCTIONS
Simibox Light
Hot water = left
Simibox Light
Cold water = right
HOT COLD
G 1/2
G 1/2
Upper outlet
To close off the unused outlet, fit the plug and check the seal.
Lower outlet
Hot water
Cold water
Connection to the water mains
page 2 of 7
LAUFEN
Plumbers, please ensure a copy of the installation
instructions is left with the end user for future reference
SIMIBOX LIGHT W/O SHUT-OFF
Connection to the water mains
Cold or mixed water Mixer
Purge from the front
7.81038.000.000
Hot waterCold water Cold water
Plug/gasket x 2
Thin wall
The mounting flanges are adjustable according to the depth of the housing
Thick wall
Fitting the flanges
page 3 of 7
LAUFEN
Plumbers, please ensure a copy of the installation
instructions is left with the end user for future reference
SIMIBOX LIGHT W/O SHUT-OFF
The front face of the tiling must lie between the min. and max. dimension shown on the label
mm
25
Front face of the tiling
Use the mounting flanges as drilling template
It is recommended to use at least 4 fixing
points (Ø 5 screws) to fix the appliance into or
onto the wall. For front wall installation, it is
strongly recommended to use 8 x M5 screws
Position and align the built-in unit using a spirit level
Pre-installation
page 4 of 7
LAUFEN
Plumbers, please ensure a copy of the installation
instructions is left with the end user for future reference
SIMIBOX LIGHT W/O SHUT-OFF
Embedded in the wall with fixing rails
Cold water = right
Embedded in the wall
Surface mounting
Simibox Light
Hot water = left
Simibox Light
Remote installation on the wall with flanges
(each flange 8 mm thick)
Examples of installation
page 5 of 7
LAUFEN
Plumbers, please ensure a copy of the installation
instructions is left with the end user for future reference
SIMIBOX LIGHT W/O SHUT-OFF
Installation with supporting frame
Installation behind a prefabricated wall
Examples of installation
Pressure test and network purging
Both exits must be purged
Purge through the outlets Purge from the front
O P TION 9.20793.903.001
Rinsing device with stop-cock
Pressure test
While still accessible, the water pipes
must be subjected to a pressure test. The
resistance pressure of the concealed body
Simibox) is PN 10,
current local instructions
page 6 of 7
LAUFEN
Plumbers, please ensure a copy of the installation
instructions is left with the end user for future reference
SIMIBOX LIGHT W/O SHUT-OFF
If necessary put a silicone seal between the wall and the box
Coat the wall with adhesive and fit the sealing cu
Apply the wall decoration
Take the lid off and cut the plastic case flush with the wall using a cutter
Finishing
page 7 of 7
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7

Laufen 9505792 Technical Guide

Laufen
Brand
Laufen
Model
9505792
Type
Technical Guide

Laufen 9505792 is a mixer that can be used in domestic, hotel, and commercial settings. It has a chrome finish and is suitable for use with storage tank and continuous flow hot water units. The maximum continuous operating pressure is 1000kPa, but for best performance and longer life, it is recommended to use between 150-500kPa. Hot and cold water inlet pressure should be equal. The maximum continuous working temperature is 80°C. The mixer comes factory assembled and tested, and it is not recommended to dismantle any internal parts.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages