IDS GigE uEye SE Rev. 4 Technical Manual

Brand
IDS
Model
GigE uEye SE Rev. 4
Type
Technical Manual
GigE uEye FA
IDS Imaging Development Systems GmbH
Dimbacher Str. 6-8
D-74182 Obersulm, Germany
T: +49 7134 96196-0
E: info@ids-imaging.com
W: http://www.ids-imaging.com
Technical Manual
January 2020 2
Technical Manual: GigE uEye FA
Contents
1 Preface .............................................................................................................................................. 3
2 Symbols and hints ............................................................................................................................ 4
3 Safety instructions ............................................................................................................................ 5
4 Standards and directives .................................................................................................................. 7
5 GigE uEye FA .................................................................................................................................... 8
5.1 Ambient conditions ...................................................................................................................... 9
5.2 System requirements ................................................................................................................. 10
5.3 Connecting a GigE uEye FA ....................................................................................................... 10
6 Mechanical specifications ................................................................................................................ 11
7 Optical specifications ...................................................................................................................... 12
7.1 Immersion depth for lenses ......................................................................................................... 12
7.2 Position accuracy of the sensor .................................................................................................. 13
8 Electrical specifications ................................................................................................................... 14
8.1 Pin assignment M12 Ethernet connector ...................................................................................... 14
8.2 Pin assignment I/O connector ..................................................................................................... 14
8.3 Digital input wiring ...................................................................................................................... 15
8.4 Digitaloutput wiring ..................................................................................................................... 16
8.5 General Purpose I/O wiring ......................................................................................................... 18
9 Status LED ...................................................................................................................................... 20
10 Filter glasses ................................................................................................................................. 21
10.1 Filter types .............................................................................................................................. 21
10.2 Cleaning the filter glasses ......................................................................................................... 22
Index .................................................................................................................................................. 24
January 2020 3
Technical Manual: GigE uEye FA
1 Preface
Introduction
IDS Imaging Development Systems GmbH has taken every possible care in preparing this manual. We
however assume no liability for the content, completeness or quality of the information contained therein. The
content of this manual is regularly updated and adapted to reflect the current status of the software. We
furthermore do not guarantee that this product will function without errors, even if the stated specifications are
adhered to.
Under no circumstances can we guarantee that a particular objective can be achieved with the purchase of
this product.
Insofar as permitted under statutory regulations, we assume no liability for direct damage, indirect damage or
damages suffered by third parties resulting from the purchase of this product. In no event shall any liability
exceed the purchase price of the product.
Please note that the content of this manual is neither part of any previous or existing agreement, promise,
representation or legal relationship, nor an alteration or amendment thereof. All obligations of IDS Imaging
Development Systems GmbH result from the respective contract of sale, which also includes the complete and
exclusively applicable warranty regulations. These contractual warranty regulations are neither extended nor
limited by the information contained in this manual. Should you require further information on this product, or
encounter specific problems that are not discussed in sufficient detail in the manual, please contact your local
dealer or system installer.
Trademarks The IDS logo is a registered trademark of IDS Imaging Development Systems GmbH,
registered for U.S. (Reg.No. 4,513,138) and other countries.
IDS NXT and uEye are registered trademarks of IDS Imaging Development Systems
GmbH. Microsoft and Windows are trademarks or registered trademarks of Microsoft Corporation. All other
products or company names mentioned in this manual are used solely for purposes of identification or
description and may be trademarks or registered trademarks of the respective owners.
Copyright
ยฉ IDS Imaging Development Systems GmbH. All rights reserved. This manual may not be reproduced,
transmitted or translated to another language, either as a whole or in parts, without the prior written permission
of IDS Imaging Development Systems GmbH.
Status: January 2020
Contact
Visit our web site http://www.ids-imaging.com where you will find all the latest information about our software
and hardware products. Please contact your local IDS distributors for first level support in your language. For
a list of IDS distributors worldwide please go to our website http://www.ids-imaging.com.
Address
IDS Imaging Development Systems GmbH
Dimbacher Str. 6-8
D-74182 Obersulm, Germany
T
+49 7134 96196-0
E
info@ids-imaging.com
W
http://www.ids-imaging.com
January 2020 4
Technical Manual: GigE uEye FA
2 Symbols and hints
This symbol indicates hints with useful information for better understanding and using
features and functions.
This symbol indicates important warnings for product safety to prevent damage.
This symbol indicates important warnings for personal safety to prevent injury.
January 2020 5
Technical Manual: GigE uEye FA
3 Safety instructions
Read carefully these safety instructions before installing and using the product. The producer is not
responsible for damages and injury, which can occur due to false handling of the product and ignoring the
safety instructions. All warranty will be spoiled in this case.
Intended use
IDS industrial cameras are to be used to capture images for visualization and image processing tasks. They
are designed for use in industrial environments. Please comply with the requirements for the proper use of this
product. Failure to do so will render the warranty void.
The product is not authorized for use in security relevant applications. If it used in security relevant
applications, the customer is responsible for the necessary approvals.
If the product is modified or changed, all approval becomes invalid. In this case, the customer is responsible
for ensuring product conformity.
The warranty expires if the product is improperly disassembled, reworked or repaired by the customer or a
third party and IDS Imaging Development Systems GmbH assumes no liability for defects. If you need
service, please contact the support team.
The product is not a toy. Operate and store out of the reach of children.
Protection against electrostatic discharge (ESD)
Board-level cameras are especially sensitive to electrostatic discharge. Make sure to avoid mechanical or
electrical damage of the printed circuit board or its connections. Wear ESD-protective clothing and observe
the rules for handling ESD-sensitive components.
Do not touch the printed circuit board while it is powered.
Always hold the board by the edges to avoid the risk of electrostatic discharge damage.
For optimum ESD behavior, a clearance of 4 mm from non-shielded housings must be maintained all the
way around. For shielded housings, a smaller clearance is possible.
Attach the board to a conductive surface using the fixing screws. If this is not possible, ensure an insulating
connection.
Use connecting cable with a low-resistance shield on both sides.
Installation, operation and maintenance
The product must be connected, taken into operation and maintained only by appropriately qualified
personnel. The error-free and safe operation of this product can only be ensured if it is properly transported,
stored, set up and assembled, and operated and maintained with due care. The installation, inspection,
maintenance, extension, and repair may only be done by authorized personnel.
Observe the specifications in the documentation when installing the product.
Do not subject the product to direct sunlight, moisture or shock. Note in particular the permitted IP code of
the product.
Only operate the product under ambient conditions for which the respective product is approved. The use
under other ambient conditions may result in damage.
To avoid any damage to the connectors, only mount or remove the product with the cables disconnected.
Lay cables in such way that no one is endangered.
Before starting up, check if the electrical wiring corresponds to the specifications in the documentation.
Faulty wiring (overvoltage, undervoltage) can result in a damage in the electronics.
Transport
Only use ESD packaging for storage and transport of ESD-sensitive components.
Keep packing materials like films away from children. Abuse may result in suffocation.
January 2020 6
Technical Manual: GigE uEye FA
Operation and power supply
The camera power supply must meet the requirements for SELV (safety extra low voltage)/LPS (limited power
source) or ES1/PS2.
WARNING! Non-approved power supplies for camera operation may cause painful or dangerous electric
shock. Serious injury or death may occur. Use a power supply that meet the requirements for SELV (safety
extra low voltage)/LPS (limited power source) or ES1/PS2.
In order to ensure electrical safety, we recommend using a shielded connection cable or grounding the
camera housing so that the camera housing is connected to ground via the appropriate installation.
Avis pour le Canada
Fonctionnement et alimentation รฉlectrique
L'alimentation รฉlectrique de la camรฉra doit รชtre conforme aux exigences de sรฉcuritรฉ SELV (trรจs basse
tension de sรฉcuritรฉ)/LPS (source ร  puissance limitรฉe) ou ES1/PS2.
AVERTISSEMENT ! Avec un bloc d'alimentation non prรฉvu pour les camรฉras, il existe des risques de
dรฉcharges รฉlectriques douloureuses ou dangereuses. Celles-ci peuvent provoquer des blessures graves,
voire mortelles. Utilisez un bloc d'alimentation conforme aux exigences de sรฉcuritรฉ SELV (trรจs basse
tension de sรฉcuritรฉ)/LPS (source ร  puissance limitรฉe) ou ES1/PS2.
Pour garantir la sรฉcuritรฉ รฉlectrique, nous recommandons l'utilisation d'un cรขble de connexion blindรฉ ou la
mise ร  la terre du boรฎtier de la camรฉra, afin que ce dernier soit reliรฉ correctement ร  la masse.
CAUTION! As the camera housing may get hot depending on the operating conditions there may be risk of
burns. Provide sufficient heat dissipation so that the housing temperature does not exceed 55 ยฐC (131 ยฐF).
NOTICE! Cameras with Power-over-Ethernet (PoE) can be supplied with voltage both from an external source
and via PoE. The camera should not be supplied through both voltage sources at once as this can irreparably
damage the camera.
Correct disposal
Dispose the camera and accessories properly and separately from other types of waste to encourage
recycling of reusable materials and to protect the environment.
According to the EC Directive 2012/19/EU (WEEE) we are obliged to take back this product, distributed by us
after August 13, 2005, free of charge at the end of its useful life and to ensure it correct disposal. As this
product is exclusively for commercial use (B2B), it must not be handed over to a public disposal facility. The
product can be disposed of by specifying the date of purchase and the serial number at the following address:
IDS Imaging Development Systems GmbH
Dimbacher Str. 6-8
D-74182 Obersulm, Germany
January 2020 7
Technical Manual: GigE uEye FA
4 Standards and directives
(only valid for devices with housing)
IDS Imaging Development Systems GmbH hereby confirms that this product has been developed, designed
and manufactured in compliance with the following European directives
2014/30/EU: EMC - Electromagnetic compatibility
2011/65/EU: RoHS - Restriction of the use of certain hazardous substances in electrical and electronic
equipment
Regulation (EC) No. 1907/2006 concerning the Registration, Evaluation, Authorization and Restriction of
Chemicals (REACH)
The CE declaration of conformity is available on the IDS website.
If the product is modified or changed all approval becomes invalid. In this case the customer is responsible for
ensuring product conformity.
Product type
GigE uEye FA
Information for CE
EMC specifications
EN 61000-6-2
EN 61000-6-3*
EN 55032 (Class B)
Information for USA
This equipment has been tested and found to comply with part 15 of
the FCC Rules.
Class B
Information for Canada
Renseignements pour le Canada
CAN ICES-3 (B)/NMB-3(B)
Information for UL
To be compliant with the UL safety criteria GigE cameras must be
operated with indoor networks only.
UL 62368-1
CAN/CSA C22.2 No. 62368-1-14
Further information
KC (R-R-img-GIGEFA)
ChinaRoHS EFUP 25
* Cameras are intended for use in industrial, residential, commercial and light industrial environments.
For customers in the USA
For a class B digital device:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and Receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Name of Responsible Party
IDS Imaging Development Systems, Inc.
92 Montvale Ave., Ste 2800
Stoneham, MA 02180
U.S.A.
T: +1 781 787 0048
January 2020 8
Technical Manual: GigE uEye FA
5 GigE uEye FA
Housing/board-level
+/-
Dimensions height x width x length
41 x 53 x 42.7 mm
Mechanical specifications
Mechanical specifications
IP code
IP 65
Protection against penetration of dust: No ingression of dust at
a vacuum of 20 mbar in the housing
Protection against water (out of a nozzle) from all directions
Test conditions: Using a jet nozzle with an inside diameter of
6.3 mm, a jet of water at a volume flow of 12.5 liters per minute
is applied to the housing from all directions at a distance of
2.5-3 m. The testing period is at least 3 min.
IP 67
Protection against penetration of dust: No ingression of dust at
a vacuum of 20 mbar in the housing
Protection against ingress of water in case of temporary
immersion
Test conditions: The housing is dipped completely under water
in a dip tank. The submerged depth is 1 m and the testing
period is 30 min. Water may not intrude in a quantity which
causes harmful effects while the housing is dipped in water
under standardized pressure and time conditions.
Ambient conditions
Ambient conditions
Lens mount
C-mount, see Optical specifications
Mounting holes bottom/top/side/front
3/0/0/0
Thread diameter
M5
Status LED
Status LED
Interface connector
M12 connector, screwable
Power supply
PoE or 12-24 V external
I/O connector
8-pin Binder 712, screwable
Electrical specifications
Electrical specifications
Special features
Integrated image memory
Internal pixel pre-processing
Can be supplied via Power-over-Ethernet
January 2020 9
Technical Manual: GigE uEye FA
5.1 Ambient conditions
The temperature values given below refer to the outer device temperature of the camera housing. The
temperature inside of the camera housing is generally higher than the outer temperature and may be up to
70 ยฐC (158 ยฐF).
Device temperature during operation
0 ยฐC โ€ฆ 55 ยฐC
32 ยฐF โ€ฆ 131 ยฐF
Device temperature during storage
-20 ยฐC โ€ฆ 60 ยฐC
-4 ยฐF โ€ฆ 140 ยฐF
Humidity*
20 % โ€ฆ 100 %, relative, non-condensing
* Only if GigE uEye FA lens tube and IP65/67 cables are used
Non-condensing means that the relative air humidity must be below 100 %. Otherwise, moisture will form on
the camera surface. If, for example, air has a relative humidity of 40 % at 35 ยฐC (95 ยฐF), the relative humidity
will increase to over 100 % if the air cools down to 19.5 ยฐC (67 ยฐF); condensation begins to form.
CAUTION! As the camera housing may get hot depending on the operating conditions there
may be risk of burns. Provide sufficient heat dissipation so that the housing temperature does
not exceed 55 ยฐC (131 ยฐF).
Notes on ambient conditions
Avoid high air humidity levels and rapid temperature changes when using IDS cameras.
Temperatures below +4 ยฐC (39 ยฐF) combined with excessive relative air humidity levels can cause icing.
Provide sufficient heat dissipation so that the specified device temperature is not exceeded during operation.
In general, the following recommendations apply:
For a passive heat dissipation, mount the camera on a thermally-conductive surface like a metal plate or a
heat sink.
If necessary, provide an active cooling for example by means of a fan.
With increasing device temperatures, the image quality could be reduced due to thermal noise. It is
recommended to mount the camera to a heat-dissipating unit even if the camera is operated below the
maximum specified temperature.
Vibration and shock resistance
Vibration and shock resistance of the cameras were tested as specified in EN 60068-2-6 and EN 60068-2-27.
Test parameter EN 60068-2-6 "Environmental testing - Tests: Vibration"
Vibration mode: Sinus
Lower frequency: 30 Hz
Upper frequency: 500 Hz
Acceleration: 10 g
Throughput speed: 1 octave/minute, logarithmic
Number of frequency cycles: 10 per axis
Test parameter EN 60068-2-27 "Environmental testing - Tests: Shock"
Shock form: half sine
Pulse duration: 1,9 ms
Peak acceleration: 80 g
Number of shocks per direction: 3 (ยฑ X, ยฑY, ยฑZ)
Shock form: half sine
Pulse duration: 6 ms
Peak acceleration: 25 g
Number of shocks per direction: 100 (ยฑ X, ยฑY, ยฑZ)
January 2020 10
Technical Manual: GigE uEye FA
5.2 System requirements
For operating the cameras, the following system requirements must be met:
Camera
GigE uEye FA
Interface
Gigabit Ethernet-Port (1000 Mbps)
CPU
Intel i3 or better
Memory
Min. 2 GB
Disk space
Min. 500 MB
Operating system Windows
Windows 10 (32/64-bit)
Windows 8.1/8 (32/64-bit)
Windows 7 Service Pack 1 (32/64-bit)
Operating system Linux
Linux > Kernel 2.6 (32/64-bit)
Depending on the sensor model, the camera performance may be limited with the minimum system
requirements.
5.3 Connecting a GigE uEye FA
Check the power supply to the camera. Connect the camera to to a Gigabit Ethernet port on the PC either
directly or using switches. Please read the following notes before setting up.
Cabling
The data network and the camera network should be cabled separately. Therefore, it is recommend
connecting the cameras by a separate network card.
It is recommend to use Cat5e type cables.
The cable length of the individual segments must not exceed 100 m. A segment is a continuous cable
connection between two network devices (e.g. PC, camera, switch).
It is recommended to cable the network throughout at 1000 Mbit/s.
Network card
To ensure optimum performance of the network connection, you need to install the latest drivers for your
network card.
GigE network adapters for PCI slots are limited in its transfer rate to approximately 80-90 MByte/s.
It is recommended to set the "Receive Descriptors" in the network card settings to the maximum value.
It is recommended to set the "Jumbo Frames" (also: Jumbo Packet) in the network card settings to the
maximum value.
Note that the connection between the camera and the PC must continuously be able to transport jumbo
packets to ensure the transmission of the jumbo packets. Information on these settings is provided in the
manual supplied with the network adapter.
January 2020 11
Technical Manual: GigE uEye FA
6 Mechanical specifications
The mechanical data for each camera model can be found on our website directly at the respective camera
model beneath in the "Downloads" tab.
NOTICE! The camera connectors may be damaged if you install or remove the camera with
plugged in cables. Therefore, first unplug the GigE and/or I/O cable from the camera.
Note on the IP 65/67 standards
The GigE uEye FA housing version is IP 65/67 compliant. The following requirements must
be met for conformance to the IP 65/67 standards:
Cables must be attached to both connectors during operation.
A lens tube must be connected.
Attention: The GigE uEye FA has not been approved for underwater use.
Note on the rubber gasket at the tube thread (camera side)
Check the rubber gasket for damage before mounting a protective lens tube. If you will be
using the camera without a lens tube for a prolonged time, remove the rubber gasket and
store it away from light, as UV light and ozone can cause the gasket to become porous.
If you need to grease the thread, use only silicone oil or silicone grease.
January 2020 12
Technical Manual: GigE uEye FA
7 Optical specifications
Immersion depth for lenses
Position accuracy of the sensor
7.1 Immersion depth for lenses
Some C-mount lenses reach deep into the camera flange. This may cause the lens to push against the back
of the filter glass inside the camera or even make it impossible to screw in the lens.
The table below indicates the maximum possible immersion depth. The actual immersion depth of a lens is
given in the relevant data sheet. As lens parts with a small diameter are allowed to reach deeper into the
camera flange, the immersion depths are specified based on the diameter (named as A, B, and C in the
image below).
Beside the immersion depth also the back focal length has to be considered, that means the distance between
the last lens and the sensor (named "bfl" in the image below). The back focal length can be calculated for C-
mount with the following formula:
x17.526bfl
x stands for the maximum immersion depth (see table below).
Fig. 2: Camera front (sectional view)
The data given in the table include the following tolerances as a safety clearance:
Immersion depth: 0.2 mm
Diameter: 0.2 mm
Type
Thread depth
(min.)
for diameter at lens end
[mm]
ร˜ A
resulting maximum
immersion depth [mm]
minimum required back
focal length [mm]
C-mount
5 mm
24.0
11.0
6.5
January 2020 13
Technical Manual: GigE uEye FA
7.2 Position accuracy of the sensor
The following illustrations show the tolerance margins of the sensor position relative to the outer camera
housing. A maximum error in all directions (rotation, translation) cannot occur at the same time.
Fig. 3: Position accuracy of the sensor (1)
Fig. 4: Position accuracy of the
sensor (2)
It cannot be guaranteed that the sensor cover glass or filter glass are absolutely parallel to each other.
C-mount lenses can also be subject to inaccuracies of the flange back distance. The
tolerance usually is ยฑ0.05 mm. In some cases, however, the inaccuracies of camera and lens
might add up, resulting in a total error > 0.05 mm.
Position accuracy, in each direction
ยฑ0.3 mm
Horizontal/vertical rotation (ฮฑ)
ยฑ1.0ยฐ
Translational rotation (ฮฒ)
ยฑ1.0ยฐ
Flange back distance
ยฑ0.05 mm
January 2020 14
Technical Manual: GigE uEye FA
8 Electrical specifications
Pin assignment M12 Ethernet connector
Pin assignment I/O connector
Digital input wiring
Digital output wiring
General Purpose I/O wiring
Exception: PoE may be considered a Network Environment 0 per IEC TR 62101, and thus
the interconnected ITE circuits may be considered SELV, if:
1. the function of the ITE being investigated to IEC 60950-1 is considered not likely to
require connection to an Ethernet network with outside plant routing, including campus
environment; and
2. the installation instructions clearly state that the ITE is to be connected only to PoE
networks without routing to the outside plant.
8.1 Pin assignment M12 Ethernet connector
8-pin M12 socket (M12 connector: MMT361A315)
Pin
Description
Designation 1000BASE-T
Designation 100BASE-TX
Fig. 5: Ethernet
connector, camera
rear view
1
MDX0+
BI_DA+
TX+
2
MDX0-
BI_DA-
TX-
3
MDX1+
BI_DB+
RX+
4
MDX1-
BI_DB-
RX-
5
MDX3+
BI_DD+
6
MDX3-
BI_DD-
7
MDX2-
BI-DC-
8
MDX2+
BI_DC+
The M12 connector of the GigE uEye FA complies with the IEC/PAS 61076-2-109 standard.
8.2 Pin assignment I/O connector
8-pin Binder connector (Binder series 712: 09-0427-020-08)
Pin
Description
Fig. 6: I/O
connector male,
camera rear view
1
Trigger input with optocoupler (+)
2
Input power supply (VCC) 12-24 V DC
3
General purpose I/O (GPIO) 1, 3.1 V
4
Ground (GND)
5
Flash output with optocoupler (+)
6
Flash output with optocoupler (-)
7
Trigger input with optocoupler (-)
8
General purpose I/O (GPIO) 2, 3.1 V
You can check the color assignment of the cable on the Website directly at the specific accessory item.
The maximum length of the I/O cable is 30 m. The cable must be shielded.
January 2020 15
Technical Manual: GigE uEye FA
Power supply
Voltage
Tolerance
Residual ripple
12-24 V
+/- 10 %
max. 120 mVpp
IDS Imaging Development Systems GmbH recommends to adjust the power supply to the power requirement
of the camera to limit overheating in case of short circuit. To ensure electrical safety, the power supply must
meet the requirements for SELV (safety extra low voltage)/LPS (limited power source) or ES1/PS2.
Avis pour le Canada:
IDS Imaging Development Systems GmbH recommande d'adapter l'alimentation รฉlectrique aux besoins de
la camรฉra afin de limiter la surchauffe en cas de court-circuit. Pour garantir la sรฉcuritรฉ รฉlectrique,
l'alimentation doit รชtre conforme aux exigences de sรฉcuritรฉ SELV (trรจs basse tension de sรฉcuritรฉ)/LPS
(source ร  puissance limitรฉe) ou ES1/PS2.
Information on the power consumption of individual camera models can be found in the model data sheet.
NOTICE! The camera can be supplied with voltage both from an external source and via
Power-over-Ethernet (PoE). The camera should not be supplied through both voltage sources
at once as this can irreparably damage the camera.
Keep in mind that a voltage drop will occur when you use long cables for power supply to the
camera. Choose the size of the cable in such a way that the supply voltage available at the
input of the camera is at least 12 V.
To supply the GigE uEye FA camera with power using PoE or PoE+, you can use PoE
injectors or switches that are compatible with IEEE standard 802.3af or IEEE standard
802.at.
The cameras register to the PoE class 2 (3.84-6.49 W). Depending on the operating mode, a
camera can also consume less than 3.84 W.
8.3 Digital input wiring
Symbol
Min.
Typ.
Max.
Unit
Input high range
VIH
5
24
V
Input low range
VIL
0
0
1
V
Input leakage current
II
ยตA
Trigger pulse width (edge)
10
ยตs
Trigger edge steepness
35
V/ms
For interpreting the trigger signal, either the rising or the falling edge can be used. The digital input is
galvanically isolated using an optocoupler to protect the camera and the PC against surges. Only DC voltages
may be applied to the digital input.
January 2020 16
Technical Manual: GigE uEye FA
Digital input wiring
Fig. 7: Wiring of the trigger connector
8.4 Digitaloutput wiring
Symbol
Min.
Typ.
Max.
Unit
Recommended supply voltage
VCC
30
V
Collector-emitter saturation voltage
VCE(SAT)
0.03
0.15
V
Collector-emitter breakdown voltage
V(BR)CE
100
V
Collector current continuous
IC
150
mA
The digital output is galvanically isolated using an optocoupler to protect the camera and the PC against
surges. Only DC voltages may be applied to the digital output.
The output of the optocoupler can be used as an open collector or open emitter output. This means that the
output signal can be connected to ground or to the supply voltage. The output signal is active if the collector-
emitter switch is closed.
Digital output wiring
The following figures show examples of how the digital output is wired.
January 2020 17
Technical Manual: GigE uEye FA
Fig. 8: Wiring of the digital output as an open collector output
Fig. 9: Wiring of the digital output as an open emitter output
January 2020 18
Technical Manual: GigE uEye FA
8.5 General Purpose I/O wiring
The two programmable GPIOs (general purpose I/O) can be used as inputs or outputs. This selection is made
by software using the corresponding functions. Please observe the following criteria:
Symbol
Min.
Typ.
Max.
Unit
IO voltage range
VCCIO
0
-
3.3
V
Input high range
VIH
1.7
-
3.3
V
Input low range
VIL
-0.3
-
0.8
V
Input leakage current
II
-
-
-
ยตA
Output high range
VOH
-
-
3.15
V
Output low range
VOL
-
-
0.2
V
Output current high
IOH
-
-
8
mA
Output current low
IOL
-
-
8
mA
NOTICE! The General Purpose I/Os are not potential-free and have no protective circuit.
Faulty wiring (overvoltage, undervoltage) can result in a damage in the electronics.
GPIO wiring as input
Fig. 10: GPIO wiring as input
January 2020 19
Technical Manual: GigE uEye FA
GPIO wiring as output
Fig. 11: GPIO wiring as output (1)
Fig. 12: GPIO wiring as output (2)
January 2020 20
Technical Manual: GigE uEye FA
9 Status LED
Fig. 13: Status LEDs
The camera has two LEDs that indicate information of the current status.
LED 1: camera status (two-color)
LED 2: Network status (two-color)
LED 1
Camera is off/no power
Camera is booting
Camera is ready
Camera is open
No firmware loaded
LED 2
No network connection
Network connection OK
Network connection OK + data transfer
Continuous data transfer
Network error
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24

IDS GigE uEye SE Rev. 4 Technical Manual

Brand
IDS
Model
GigE uEye SE Rev. 4
Type
Technical Manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents