Apply when air and surface temperatures are above 45°F (7°C) . For
exterior use, recommended only as a spot primer. Do not use on
solvent sensitive stains such as asphalt and tar. Must be topcoated.
Extended period before topcoating may affect performance. Drying
times listed may vary depending on temperature, humidity and air
movement. DANGER - Rags, steel wool or waste soaked with this
product may spontaneously catch fire if improperly discarded.
Immediately after use, place rags, steel wool or waste in a sealed
water-filled metal container. Refer to www.pittsburghpaints.com,
Spontaneous Combustion Advisory for additional information.
SPEEDHIDE® Interior Quick Dry Stain Kill Primer SealerSPEEDHIDE® Interior Quick Dry Stain Kill Primer SealerSPEEDHIDE® Interior Quick Dry Stain Kill Primer Sealer
Excellent Adhesion to a Wide Variety of Surfaces (including glossy
substrates)
For Blocking Stains, including Water, Nicotine, Markers
Quick Dry-Re-coat in 1 hour
Interior Only
Meets MPI Category #136, Stain Blocking Primer (Solvent Based)
Our best professional alkyd stain blocking primer designed to meet
the performance requirements of the professional applicators.
SPEEDHIDE® Primer provides excellent adhesion to a wide range of
surfaces, blocking and sealing out a variety of common stains
including water, nicotine, markers, and graffiti stains. SPEEDHIDE®
Primer can be re-coated in 1 hour and provides excellent adhesion to
glossy surfaces, like Formica, aluminum, and tile. It is also
recommended for use on wood, wallboard, brick, cement composition
board, and cured masonry, plaster, cement, and stucco.
Architectural Coatings
General Description
Tinting and Base Information
Recommended Uses
Features / Benefits
Limitations of Use
Generic Type
Alkyd Resin
Brick Cement
Concrete Block (CMU)Concrete Block (CMU)Concrete Block (CMU)Concrete Block (CMU) Masonry
Plaster Wallboard
Wood
DO NOT TINT.DO NOT TINT.
6-146-146-14 White
Product Data
SPEEDHIDE®SPEEDHIDE®
A1.7A1.7A1.7A1.7
6-146-146-14
4 to 10 (60º Gloss Meter)4 to 10 (60º Gloss Meter)4 to 10 (60º Gloss Meter)4 to 10 (60º Gloss Meter)4 to 10 (60º Gloss Meter)4 to 10 (60º Gloss Meter)4 to 10 (60º Gloss Meter)4 to 10 (60º Gloss Meter)
Gloss:Gloss:
3.50 lbs/gal (420.00 g/L) 3.50 lbs/gal (420.00 g/L) 3.50 lbs/gal (420.00 g/L) 3.50 lbs/gal (420.00 g/L) 3.50 lbs/gal (420.00 g/L) 3.50 lbs/gal (420.00 g/L) 3.50 lbs/gal (420.00 g/L) 3.50 lbs/gal (420.00 g/L) 3.50 lbs/gal (420.00 g/L) 3.50 lbs/gal (420.00 g/L) 3.50 lbs/gal (420.00 g/L) 3.50 lbs/gal (420.00 g/L) 3.50 lbs/gal (420.00 g/L) 3.50 lbs/gal (420.00 g/L)
VOC*:VOC*:
1.70 minimum to 1.80 maximum mils 1.70 minimum to 1.80 maximum mils 1.70 minimum to 1.80 maximum mils 1.70 minimum to 1.80 maximum mils 1.70 minimum to 1.80 maximum mils 1.70 minimum to 1.80 maximum mils 1.70 minimum to 1.80 maximum mils 1.70 minimum to 1.80 maximum mils
DFT:DFT:
400 to 450 sq. ft./gal. (37 to 42 sq. m/3.78L)400 to 450 sq. ft./gal. (37 to 42 sq. m/3.78L)400 to 450 sq. ft./gal. (37 to 42 sq. m/3.78L)400 to 450 sq. ft./gal. (37 to 42 sq. m/3.78L)400 to 450 sq. ft./gal. (37 to 42 sq. m/3.78L)400 to 450 sq. ft./gal. (37 to 42 sq. m/3.78L)400 to 450 sq. ft./gal. (37 to 42 sq. m/3.78L)400 to 450 sq. ft./gal. (37 to 42 sq. m/3.78L)400 to 450 sq. ft./gal. (37 to 42 sq. m/3.78L)400 to 450 sq. ft./gal. (37 to 42 sq. m/3.78L)400 to 450 sq. ft./gal. (37 to 42 sq. m/3.78L)400 to 450 sq. ft./gal. (37 to 42 sq. m/3.78L)400 to 450 sq. ft./gal. (37 to 42 sq. m/3.78L)400 to 450 sq. ft./gal. (37 to 42 sq. m/3.78L)400 to 450 sq. ft./gal. (37 to 42 sq. m/3.78L)400 to 450 sq. ft./gal. (37 to 42 sq. m/3.78L)400 to 450 sq. ft./gal. (37 to 42 sq. m/3.78L)400 to 450 sq. ft./gal. (37 to 42 sq. m/3.78L)400 to 450 sq. ft./gal. (37 to 42 sq. m/3.78L)400 to 450 sq. ft./gal. (37 to 42 sq. m/3.78L)400 to 450 sq. ft./gal. (37 to 42 sq. m/3.78L)
Coverage:Coverage:
Note: Does not include loss due to varying application method, surface porosity, or mixing.Note: Does not include loss due to varying application method, surface porosity, or mixing.Note: Does not include loss due to varying application method, surface porosity, or mixing.Note: Does not include loss due to varying application method, surface porosity, or mixing.
46% +/- 2.0%46% +/- 2.0%46% +/- 2.0%46% +/- 2.0%46% +/- 2.0%46% +/- 2.0%
Volume Solids*:Volume Solids*:
71% +/- 2.0%71% +/- 2.0%71% +/- 2.0%71% +/- 2.0%71% +/- 2.0%71% +/- 2.0%
Weight Solids*:Weight Solids*:
12.1 lbs. (5.5 kg) +/- 0.2 lbs. (91 g)12.1 lbs. (5.5 kg) +/- 0.2 lbs. (91 g)12.1 lbs. (5.5 kg) +/- 0.2 lbs. (91 g)12.1 lbs. (5.5 kg) +/- 0.2 lbs. (91 g)12.1 lbs. (5.5 kg) +/- 0.2 lbs. (91 g)12.1 lbs. (5.5 kg) +/- 0.2 lbs. (91 g)12.1 lbs. (5.5 kg) +/- 0.2 lbs. (91 g)12.1 lbs. (5.5 kg) +/- 0.2 lbs. (91 g)12.1 lbs. (5.5 kg) +/- 0.2 lbs. (91 g)12.1 lbs. (5.5 kg) +/- 0.2 lbs. (91 g)12.1 lbs. (5.5 kg) +/- 0.2 lbs. (91 g)12.1 lbs. (5.5 kg) +/- 0.2 lbs. (91 g)12.1 lbs. (5.5 kg) +/- 0.2 lbs. (91 g)12.1 lbs. (5.5 kg) +/- 0.2 lbs. (91 g)12.1 lbs. (5.5 kg) +/- 0.2 lbs. (91 g)12.1 lbs. (5.5 kg) +/- 0.2 lbs. (91 g)12.1 lbs. (5.5 kg) +/- 0.2 lbs. (91 g)12.1 lbs. (5.5 kg) +/- 0.2 lbs. (91 g)
Weight/Gallon*:Weight/Gallon*:Weight/Gallon*:Weight/Gallon*:
Mineral Spirits
Cleanup:Cleanup:
*Product data calculated on product 6-14.*Product data calculated on product 6-14.*Product data calculated on product 6-14.*Product data calculated on product 6-14.*Product data calculated on product 6-14.*Product data calculated on product 6-14.
Drying Time:Drying Time:
20 minutes20 minutesTo Touch:To Touch:
1 hour1 hourTo Handle:To Handle:
1 hour1 hourTo Recoat:To Recoat:
4 hours4 hoursTo Full Cure:To Full Cure:
Dry Time @77°F (25°C); 50% relative humidityDry Time @77°F (25°C); 50% relative humidityDry Time @77°F (25°C); 50% relative humidityDry Time @77°F (25°C); 50% relative humidityDry Time @77°F (25°C); 50% relative humidityDry Time @77°F (25°C); 50% relative humidityDry Time @77°F (25°C); 50% relative humidityDry Time @77°F (25°C); 50% relative humidityDry Time @77°F (25°C); 50% relative humidityDry Time @77°F (25°C); 50% relative humidityDry Time @77°F (25°C); 50% relative humidityDry Time @77°F (25°C); 50% relative humidityDry Time @77°F (25°C); 50% relative humidity
73°F, (22.8°C)73°F, (22.8°C)73°F, (22.8°C)73°F, (22.8°C)73°F, (22.8°C)73°F, (22.8°C)73°F, (22.8°C)73°F, (22.8°C)73°F, (22.8°C)73°F, (22.8°C)
Flash Point:Flash Point:
SPEEDHIDE® Interior Quick Dry Stain Kill Primer SealerSPEEDHIDE® Interior Quick Dry Stain Kill Primer SealerSPEEDHIDE® Interior Quick Dry Stain Kill Primer Sealer
Recommended Spread Rates:
Packaging:
Wet Mils :
Dry Mils :
maximumminimum to
Architectural Coatings
minimum to
Surface to be primed must be clean, dry, and free of dirt, loose and peeling paint, mildew, chalk, grease, rust, and other surface contaminants. Cracks,
gouges or other surface imperfections should be repaired prior to using sealer. For best adhesion, sand all glossy, rough, and patched surfaces.
WARNING! If you scrape, sand, or remove old paint, you may release lead dust or fumes. LEAD IS TOXIC. EXPOSURE TO LEAD DUST OR
FUMES CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD
ALSO AVOID EXPOSURE. Wear a properly fitted NIOSH-approved respirator and prevent skin contact to control lead exposure. Clean up
carefully with a HEPA vacuum and a wet mop. Before you start, find out how to protect yourself and your family by contacting the USEPA
National Lead Information Hotline at 1-800-424-LEAD or log on to www.epa.gov/lead. In Canada contact a regional Health Canada office. Follow
these instructions to control exposure to other hazardous substances that may be released during surface preparation.
NEW WOOD: New wood should be sanded smooth and wiped clean. Any knots or resinous areas should be sealed before painting. Countersink all
nails. Putty flush with surface, then prime.
PREVIOUSLY PAINTED WOOD: All excessive chalking must be removed and the surface rinsed thoroughly. Remove all loose, peeling, or flaking
paint by scraping or sanding. Feather back all rough edges to sound surface by sanding. Prime all bare wood areas.
CONCRETE BLOCK, CINDER BLOCK, VERTICAL MASONRY: New concrete should cure for at least 30 days and preferably 90 days prior to
priming.
Severe stains may require two coats of primer.
General Surface Preparation
Recommended Primers
1-Gallon (3.78L)1-Gallon (3.78L)1-Gallon (3.78L)1-Gallon (3.78L)1-Gallon (3.78L)1-Gallon (3.78L)1-Gallon (3.78L)1-Gallon (3.78L)1-Gallon (3.78L)
5-Gallon (18.9L)5-Gallon (18.9L)5-Gallon (18.9L)5-Gallon (18.9L)5-Gallon (18.9L)5-Gallon (18.9L)5-Gallon (18.9L)5-Gallon (18.9L)5-Gallon (18.9L)
Quart (946 mL)Quart (946 mL)Quart (946 mL)Quart (946 mL)Quart (946 mL)
Application Information
Plaster 4-6034-6034-603
New Concrete/MasonryNew Concrete/MasonryNew Concrete/Masonry 4-6034-6034-603
SPEEDHIDE®SPEEDHIDE®
maximum
91.491.491.4 101.6101.6101.6
minimum to
maximum
maximum
43.843.843.8 45.745.745.7
minimum to
3.63.63.6 4.04.04.0
1.71.71.7 1.81.81.8
Material:
Ambient:
Substrate:
50 to 9050 to 9050 to 90
45 to 10545 to 10545 to 105
45 to 10545 to 10545 to 105
°F°F
°F°F
°F°F
Permissible temperatures during application:
10 to 3210 to 3210 to 32
7 to 417 to 417 to 41
7 to 417 to 417 to 41
°C°C
°C°C
°C°C
Stir thoroughly before using and frequently during use. USE WITH
ADEQUATE VENTILATION. KEEP OUT OF REACH OF
CHILDREN. Explosion-proof equipment must be used when coating with
these materials in confined areas. Keep containers closed and away from
heat, sparks, and flames when not in use. Read all label and Material
Safety Data Sheet (MSDS) information prior to use. MSDS are available
through our website or by calling 1-800-441-9695.
Directions for Use
Not all products are available in all sizes.
Wet Microns:
Dry Microns:
Application Equipment: Apply with a high quality brush, roller,
paint pad, or by spray equipment. Severe stains may require two
coats of primer. Spray equipment must be handled with due care
and in accordance with manufacturer's recommendation.
High-pressure injection of coatings into the skin by airless
equipment may cause serious injury.
Airless Spray:Airless Spray: Pressure 1700 psi, 0.011" - 0.019" tipPressure 1700 psi, 0.011" - 0.019" tipPressure 1700 psi, 0.011" - 0.019" tipPressure 1700 psi, 0.011" - 0.019" tipPressure 1700 psi, 0.011" - 0.019" tipPressure 1700 psi, 0.011" - 0.019" tipPressure 1700 psi, 0.011" - 0.019" tipPressure 1700 psi, 0.011" - 0.019" tipPressure 1700 psi, 0.011" - 0.019" tipPressure 1700 psi, 0.011" - 0.019" tipPressure 1700 psi, 0.011" - 0.019" tipPressure 1700 psi, 0.011" - 0.019" tip
Brush:Brush: High Quality Natural Bristle Brush
Roller:Roller: 3/8" - 3/4" nap roller cover.3/8" - 3/4" nap roller cover.3/8" - 3/4" nap roller cover.3/8" - 3/4" nap roller cover.3/8" - 3/4" nap roller cover.3/8" - 3/4" nap roller cover.3/8" - 3/4" nap roller cover.3/8" - 3/4" nap roller cover.3/8" - 3/4" nap roller cover.3/8" - 3/4" nap roller cover.
DO NOT THIN.DO NOT THIN.
Thinning:
6-146-146-14
10/200610/200610/2006A1.7A1.7A1.7A1.7
PPGAF believes the technical data presented is currently accurate: however, no guarantee of accuracy, comprehensiveness, or performance is given or implied.
Improvements in coatings technology may cause future technical data to vary from what is in this bulletin. For complete, up-to-date technical information, visit our web site or
call 1-800-441-9695.
PPG Industries, Inc.
Architectural Coatings
One PPG Place
Pittsburgh, PA 15272
www.pittsburghpaints.com
Technical Services
1-800-441-9695
1-888-807-5123 fax
Architect/Specifier
1-888-PPG-IDEA
PPG Architectural Finishes
400 S. 13th Street
Louisville, KY 40203
PPG Canada, Inc.
Architectural Coatings
4 Kenview Blvd
Brampton, ON L6T 5E4
/