Cisco Systems ME 6500 User manual

Brand: Cisco Systems

Model: ME 6500

Category: Network switches

Type: User manual

Americas Headquarters

Cisco Systems, Inc.

170 West Tasman Drive

San Jose, CA 95134-1706

USA

http://www.cisco.com

Tel: 408 526-4000

800 553-NETS (6387)

Fax: 408 527-0883

Cisco ME 6500 Series Ethernet Switch

Installation Guide

October 2009

Text Part Number: OL-8900-03

THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL

STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT

WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.

THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT

SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE

OR LIMITED WARRANTY, CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.

The following information is for FCC compliance of Class A devices: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant

to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio-frequency energy and, if not installed and used in accordance with the instruction manual, may cause

harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case users will be required

to correct the interference at their own expense.

The following information is for FCC compliance of Class B devices: The equipment described in this manual generates and may radiate radio-frequency energy. If it is not

installed in accordance with Cisco’s installation instructions, it may cause interference with radio and television reception. This equipment has been tested and found to

comply with the limits for a Class B digital device in accordance with the specifications in part 15 of the FCC rules. These specifications are designed to provide reasonable

protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation.

Modifying the equipment without Cisco’s written authorization may result in the equipment no longer complying with FCC requirements for Class A or Class B digital

devices. In that event, your right to use the equipment may be limited by FCC regulations, and you may be required to correct any interference to radio or television

communications at your own expense.

You can determine whether your equipment is causing interference by turning it off. If the interference stops, it was probably caused by the Cisco equipment or one of its

peripheral devices. If the equipment causes interference to radio or television reception, try to correct the interference by using one or more of the following measures:

• Turn the television or radio antenna until the interference stops.

• Move the equipment to one side or the other of the television or radio.

• Move the equipment farther away from the television or radio.

• Plug the equipment into an outlet that is on a different circuit from the television or radio. (That is, make certain the equipment and the television or radio are on circuits

controlled by different circuit breakers or fuses.)

Modifications to this product not authorized by Cisco Systems, Inc. could void the FCC approval and negate your authority to operate the product.

The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB’s public

NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED “AS IS” WITH

ALL FAULTS. CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT

LIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF

DEALING, USAGE, OR TRADE PRACTICE.

IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING,

WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO

OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

CCDE, CCENT, CCSI, Cisco Eos, Cisco HealthPresence, Cisco IronPort, the Cisco logo, Cisco Lumin, Cisco Nexus, Cisco Nurse Connect, Cisco Pulse, Cisco StackPower,

Cisco StadiumVision, Cisco TelePresence, Cisco Unified Computing System, Cisco WebEx, DCE, Flip Channels, Flip for Good, Flip Mino, Flipshare (Design), Flip Ultra,

Flip Video, Flip Video (Design), Instant Broadband, and Welcome to the Human Network are trademarks; Changing the Way We Work, Live, Play, and Learn, Cisco Capital,

Cisco Capital (Design), Cisco:Financed (Stylized), Cisco Store, and Flip Gift Card are service marks; and Access Registrar, Aironet, AllTouch, AsyncOS, Bringing the

Meeting To You, Catalyst, CCDA, CCDP, CCIE, CCIP, CCNA, CCNP, CCSP, CCVP, Cisco, the Cisco Certified Internetwork Expert logo, Cisco IOS, Cisco Press,

Cisco Systems, Cisco Systems Capital, the Cisco Systems logo, Cisco Unity, Collaboration Without Limitation, Continuum, EtherFast, EtherSwitch, Event Center, Explorer,

Fast Step, Follow Me Browsing, FormShare, GainMaker, GigaDrive, HomeLink, iLYNX, Internet Quotient, IOS, iPhone, iQuick Study, IronPort, the IronPort logo, Laser

Link, LightStream, Linksys, MediaTone, MeetingPlace, MeetingPlace Chime Sound, MGX, Networkers, Networking Academy, Network Registrar, PCNow, PIX,

PowerKEY, PowerPanels, PowerTV, PowerTV (Design), PowerVu, Prisma, ProConnect, ROSA, ScriptShare, SenderBase, SMARTnet, Spectrum Expert, StackWise, The

Fastest Way to Increase Your Internet Quotient, TransPath, WebEx, and the WebEx logo are registered trademarks of Cisco Systems, Inc. and/or its affiliates in the United

States and certain other countries.

All other trademarks mentioned in this document or website are the property of their respective owners. The use of the word partner does not imply a partnership relationship

between Cisco and any other company. (0908R)

Cisco ME 6500 Series Ethernet Switch Installation Guide

iii

Cisco ME 6500 Series Ethernet Switch Installation Guide

OL-8900-03

CONTENTS

Preface vii

Audience vii

Organization vii

Conventions viii

Statement 1071—Warning Definition ix

Related Documentation xiv

Obtaining Documentation and Submitting a Service Request xv

CHAPTER

1Product Overview 1-1

Cisco ME 6524 Ethernet Switch (ME-C6524GS-8S) 1-1

Cisco ME 6524 Ethernet Switch (ME-C6524GT-8S) 1-7

CHAPTER

2Preparing for Installation 2-1

Safety 2-1

Site Requirements 2-3

Temperature and Air Circulation 2-3

Humidity 2-4

Altitude 2-4

Dust and Contamination 2-4

Corrosion 2-5

Electromagnetic and Radio Frequency Interference 2-5

Shock and Vibration 2-5

System Grounding 2-6

Preventing Electrostatic Discharge Damage 2-7

Power Requirements 2-9

Power Connection Guidelines for AC-Powered Systems 2-10

Power Connection Guidelines for DC-Powered Systems 2-10

Cabling Requirements 2-11

Site Preparation Checklist 2-11

Contents

Cisco ME 6500 Series Ethernet Switch Installation Guide

OL-8900-03

CHAPTER

3Installing the Switch 3-1

Preparing for Installation 3-1

Warnings 3-1

Verifying Package Contents 3-4

Required Tools 3-4

Rack-Mounting 3-4

Attaching L Brackets to the Chassis 3-5

Installing the Chassis in the Rack 3-6

Desk-Top Mounting 3-7

Installing the System Ground 3-8

Connecting Source Power to the Chassis 3-9

Connecting Source DC to the DC-Input Power Supply 3-10

Connecting Source AC to the AC-Input Power Supply 3-11

Connecting the Console Port 3-11

Installing the SFP Transceivers 3-12

Powering Up the Chassis 3-15

Where to Go Next 3-15

CHAPTER

4Removal and Replacement Procedures 4-1

Removing and Installing the DC-Input Power Supply 4-1

Required Tools 4-2

Removing the DC-Input Power Supply 4-2

Installing the DC-Input Power Supply 4-4

Removing and Installing the AC-Input Power Supply 4-6

Required Tools 4-6

Removing the AC-Input Power Supply 4-7

Installing the AC-Input Power Supply 4-8

Removing and Installing the Fan Tray 4-8

Required Tools 4-8

Removing the Fan Tray 4-9

Installing the Fan Tray 4-9

Upgrading the Memory 4-10

Contents

Cisco ME 6500 Series Ethernet Switch Installation Guide

OL-8900-03

APPENDIX

APower Supply Specifications A-1

400 W DC-Input Power Supply A-1

400 W AC-Input Power Supply A-3

400 W Power Supply AC Power Cords A-5

APPENDIX

BSFP Transceiver Specifications B-1

NDEX

Contents

Cisco ME 6500 Series Ethernet Switch Installation Guide

OL-8900-03

vii

Cisco ME 6500 Series Ethernet Switch Installation Guide

OL-8900-03

Preface

This preface describes who should read the Cisco ME 6500 Series Ethernet Switch Installation Guide,

how it is organized, and its document conventions.

Audience

Only trained and qualified service personnel (as defined in IEC 60950 and AS/NZS3260) should install,

replace, or service the equipment described in this publication.

Organization

This publication is organized as follows:

Chapter Title Description

Chapter 1 Product Overview Describes and lists the hardware features and

functionality of the Cisco ME 6500 series Ethernet

switches.

Chapter 2 Preparing for Installation Describes how to prepare your site before installing the

Cisco ME 6500 series Ethernet switches.

Chapter 3 Installing the Switch Describes how to install your Cisco ME 6500 series

Ethernet switches.

Chapter 4 Removal and

Replacement Procedures

Provides procedures for removing and installing chassis

field replaceable unit (FRU) components.

Appendix A Power Supply

Specifications

Provides specifications for the Cisco ME 6500 series

Ethernet switches power supplies.

Appendix B SFP Transceiver

Specifications

Gives descriptions of the SFP optical and copper

transceivers used with the Cisco ME 6500 series

Ethernet switches.

viii

Cisco ME 6500 Series Ethernet Switch Installation Guide

OL-8900-03

Preface

Conventions

This publication uses the following conventions:

Notes use the following conventions:

Note Means reader take note. Notes contain helpful suggestions or references to material not covered in the

publication.

Cautions use the following conventions:

Caution Means reader be careful. In this situation, you might do something that could result in equipment

damage or loss of data.

Convention Description

boldface font Commands, command options, and keywords are in

boldface.

italic font Arguments for which you supply values are in italics.

[ ] Elements in square brackets are optional.

{ x | y | z } Alternative keywords are grouped in braces and

separated by vertical bars.

[ x | y | z ] Optional alternative keywords are grouped in brackets

and separated by vertical bars.

string A nonquoted set of characters. Do not use quotation

marks around the string or the string will include the

quotation marks.

screen font Terminal sessions and information the system displays

are in screen font.

boldface screen

font

Information you must enter is in boldface screen font.

italic screen font Arguments for which you supply values are in italic

screen font.

^The symbol ^ represents the key labeled Control. For

example, the key combination ^D in a screen display

means hold down the Control key while you press the D

key.

< > Nonprinting characters, such as passwords, are in angle

brackets.

Cisco ME 6500 Series Ethernet Switch Installation Guide

OL-8900-03

Preface

Conventions

Warnings use the following conventions:

Statement 1071—Warning Definition

Warning

IMPORTANT SAFETY INSTRUCTIONS

This warning symbol means danger. You are in a situation that could cause bodily injury. Before you

work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar

with standard practices for preventing accidents. Use the statement number provided at the end of

each warning to locate its translation in the translated safety warnings that accompanied this

device.

SAVE THESE INSTRUCTIONS

Waarschuwing

BELANGRIJKE VEILIGHEIDSINSTRUCTIES

Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die lichamelijk letsel kan

veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust te zijn van de bij

elektrische schakelingen betrokken risico's en dient u op de hoogte te zijn van de standaard

praktijken om ongelukken te voorkomen. Gebruik het nummer van de verklaring onderaan de

waarschuwing als u een vertaling van de waarschuwing die bij het apparaat wordt geleverd, wilt

raadplegen.

BEWAAR DEZE INSTRUCTIES

Varoitus

TÄRKEITÄ TURVALLISUUSOHJEITA

Tämä varoitusmerkki merkitsee vaaraa. Tilanne voi aiheuttaa ruumiillisia vammoja. Ennen kuin

käsittelet laitteistoa, huomioi sähköpiirien käsittelemiseen liittyvät riskit ja tutustu

onnettomuuksien yleisiin ehkäisytapoihin. Turvallisuusvaroitusten käännökset löytyvät laitteen

mukana toimitettujen käännettyjen turvallisuusvaroitusten joukosta varoitusten lopussa näkyvien

lausuntonumeroiden avulla.

SÄILYTÄ NÄMÄ OHJEET

Attention

IMPORTANTES INFORMATIONS DE SÉCURITÉ

Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une situation pouvant

entraîner des blessures ou des dommages corporels. Avant de travailler sur un équipement, soyez

conscient des dangers liés aux circuits électriques et familiarisez-vous avec les procédures

couramment utilisées pour éviter les accidents. Pour prendre connaissance des traductions des

avertissements figurant dans les consignes de sécurité traduites qui accompagnent cet appareil,

référez-vous au numéro de l'instruction situé à la fin de chaque avertissement.

CONSERVEZ CES INFORMATIONS

Cisco ME 6500 Series Ethernet Switch Installation Guide

OL-8900-03

Preface

Conventions

Warnung

WICHTIGE SICHERHEITSHINWEISE

Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu Verletzungen führen

kann. Machen Sie sich vor der Arbeit mit Geräten mit den Gefahren elektrischer Schaltungen und

den üblichen Verfahren zur Vorbeugung vor Unfällen vertraut. Suchen Sie mit der am Ende jeder

Warnung angegebenen Anweisungsnummer nach der jeweiligen Übersetzung in den übersetzten

Sicherheitshinweisen, die zusammen mit diesem Gerät ausgeliefert wurden.

BEWAHREN SIE DIESE HINWEISE GUT AUF.

Avvertenza

IMPORTANTI ISTRUZIONI SULLA SICUREZZA

Questo simbolo di avvertenza indica un pericolo. La situazione potrebbe causare infortuni alle

persone. Prima di intervenire su qualsiasi apparecchiatura, occorre essere al corrente dei pericoli

relativi ai circuiti elettrici e conoscere le procedure standard per la prevenzione di incidenti.

Utilizzare il numero di istruzione presente alla fine di ciascuna avvertenza per individuare le

traduzioni delle avvertenze riportate in questo documento.

CONSERVARE QUESTE ISTRUZIONI

Advarsel

VIKTIGE SIKKERHETSINSTRUKSJONER

Dette advarselssymbolet betyr fare. Du er i en situasjon som kan føre til skade på person. Før du

begynner å arbeide med noe av utstyret, må du være oppmerksom på farene forbundet med

elektriske kretser, og kjenne til standardprosedyrer for å forhindre ulykker. Bruk nummeret i slutten

av hver advarsel for å finne oversettelsen i de oversatte sikkerhetsadvarslene som fulgte med denne

enheten.

TA VARE PÅ DISSE INSTRUKSJONENE

Aviso

INSTRUÇÕES IMPORTANTES DE SEGURANÇA

Este símbolo de aviso significa perigo. Você está em uma situação que poderá ser causadora de

lesões corporais. Antes de iniciar a utilização de qualquer equipamento, tenha conhecimento dos

perigos envolvidos no manuseio de circuitos elétricos e familiarize-se com as práticas habituais de

prevenção de acidentes. Utilize o número da instrução fornecido ao final de cada aviso para

localizar sua tradução nos avisos de segurança traduzidos que acompanham este dispositivo.

GUARDE ESTAS INSTRUÇÕES

¡Advertencia!

INSTRUCCIONES IMPORTANTES DE SEGURIDAD

Este símbolo de aviso indica peligro. Existe riesgo para su integridad física. Antes de manipular

cualquier equipo, considere los riesgos de la corriente eléctrica y familiarícese con los

procedimientos estándar de prevención de accidentes. Al final de cada advertencia encontrará el

número que le ayudará a encontrar el texto traducido en el apartado de traducciones que acompaña

a este dispositivo.

GUARDE ESTAS INSTRUCCIONES

Cisco ME 6500 Series Ethernet Switch Installation Guide

OL-8900-03

Preface

Conventions

Varning!

VIKTIGA SÄKERHETSANVISNINGAR

Denna varningssignal signalerar fara. Du befinner dig i en situation som kan leda till personskada.

Innan du utför arbete på någon utrustning måste du vara medveten om farorna med elkretsar och

känna till vanliga förfaranden för att förebygga olyckor. Använd det nummer som finns i slutet av

varje varning för att hitta dess översättning i de översatta säkerhetsvarningar som medföljer denna

anordning.

SPARA DESSA ANVISNINGAR

xii

Cisco ME 6500 Series Ethernet Switch Installation Guide

OL-8900-03

Preface

Conventions

Aviso

INSTRUÇÕES IMPORTANTES DE SEGURANÇA

Este símbolo de aviso significa perigo. Você se encontra em uma situação em que há risco de lesões

corporais. Antes de trabalhar com qualquer equipamento, esteja ciente dos riscos que envolvem os

circuitos elétricos e familiarize-se com as práticas padrão de prevenção de acidentes. Use o

número da declaração fornecido ao final de cada aviso para localizar sua tradução nos avisos de

segurança traduzidos que acompanham o dispositivo.

GUARDE ESTAS INSTRUÇÕES

Advarsel

VIGTIGE SIKKERHEDSANVISNINGER

Dette advarselssymbol betyder fare. Du befinder dig i en situation med risiko for

legemesbeskadigelse. Før du begynder arbejde på udstyr, skal du være opmærksom på de

involverede risici, der er ved elektriske kredsløb, og du skal sætte dig ind i standardprocedurer til

undgåelse af ulykker. Brug erklæringsnummeret efter hver advarsel for at finde oversættelsen i de

oversatte advarsler, der fulgte med denne enhed.

GEM DISSE ANVISNINGER

xiii

Cisco ME 6500 Series Ethernet Switch Installation Guide

OL-8900-03

Preface

Conventions

xiv

Cisco ME 6500 Series Ethernet Switch Installation Guide

OL-8900-03

Preface

Related Documentation

For additional Cisco ME 6500 series Ethernet switch information, refer to these publications:

• Regulatory Compliance and Safety Information for the Cisco ME 6500 Series Ethernet Switches

• Cisco ME 6500 Series Ethernet Switch Software Configuration Guide

• Cisco ME 6500 Series Ethernet Switch Command Reference

• For information about MIBs, refer to this URL:

http://www.cisco.com/public/sw-center/netmgmt/cmtk/mibs.shtml

Cisco ME 6500 Series Ethernet Switch Installation Guide

OL-8900-03

Preface

Obtaining Documentation and Submitting a Service Request

For information on obtaining documentation, submitting a service request, and gathering additional

information, see the monthly What’s New in Cisco Product Documentation, which also lists all new and

revised Cisco technical documentation, at:

http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html

Subscribe to the What’s New in Cisco Product Documentation as a Really Simple Syndication (RSS) feed

and set content to be delivered directly to your desktop using a reader application. The RSS feeds are a free

service and Cisco currently supports RSS Ve r s io n 2.0.

xvi

Cisco ME 6500 Series Ethernet Switch Installation Guide

OL-8900-03

Preface

Obtaining Documentation and Submitting a Service Request

CHAPTER

1-1

Cisco ME 6500 Series Ethernet Switch Installation Guide

OL-8900-03

Product Overview

This chapter describes the Cisco ME 6500 series Ethernet switches and contains these sections:

• Cisco ME 6524 Ethernet Switch (ME-C6524GS-8S), page 1-1

• Cisco ME 6524 Ethernet Switch (ME-C6524GT-8S), page 1-7

Cisco ME 6524 Ethernet Switch (ME-C6524GS-8S)

The ME 6524 Ethernet switch (ME-C6524GS-8S) is a member of the Cisco ME 6500 series Ethernet

switches. The Cisco ME 6524 Ethernet switch (ME-C6524GS-8S) is a 1.5 RU horizontal chassis with

24 SFP downlink ports and 8 SFP uplink ports. Figure 1-1 shows the front view of the chassis with the

major features identified; Figure 1-2 shows the rear view of the chassis with the major features

identified.

Figure 1-1 Cisco ME 6524 Ethernet Switch (ME-C6524GS-8S)—Front View

1Status LEDs 6Uplink ports LEDs

2Console port (RJ-45 connector) 7ESD chassis ground connector

3Downlink ports LEDs 8Uplink ports (SFP transceivers required)

4USB ports 9Downlink ports (SFP transceivers required)

5PCMCIA connector

147977

Catalyst 6524GS

PS1

USB

FLASH

PS2

FAN

STATUS

CONSOLE

1-2

Cisco ME 6500 Series Ethernet Switch Installation Guide

OL-8900-03

Chapter 1 Product Overview

Cisco ME 6524 Ethernet Switch (ME-C6524GS-8S)

Figure 1-2 Cisco ME 6524 Ethernet Switch (ME-C6524GS-8S)—Rear View

Table 1-1 lists the features of the Cisco ME 6524 Ethernet switch (ME-C6524GS-8S) chassis.

1System ground pad/NEBS ground location 4Power supply status LEDs

2Power supplies (DC-input power supplies

shown)

5Power supply terminal block (DC-input power

supply only)

3Fan tray 6Power on/off switch (DC-input power supply)

147978

INPUT

OUTPUT

FAN

INPUT

OUTPUT

FAN

456

Ta b l e 1-1 Cisco ME 6524 Ethernet Switch (ME-C6524GS-8S) Features

Feature Description

Chassis 1.5 RU height, fixed configuration chassis

Modules Fixed configuration chassis; modules cannot be installed in the chassis.

Fan tray • The chassis supports one hot-swappable fan tray. One fan tray model is

available:

–

FAN-C6524

Note The fan tray contains seven individual fans for chassis cooling. The

individual fans are not field replaceable; you must replace the fan

tray.

• Fan tray FAN status LED

–

Green—Fan tray is operating normally.

–

Red—One or more individual fans have failed.

1-3

Cisco ME 6500 Series Ethernet Switch Installation Guide

OL-8900-03

Chapter 1 Product Overview

Cisco ME 6524 Ethernet Switch (ME-C6524GS-8S)

Power supplies • Supports one or two power supplies. The following power supplies are

supported:

–

PWR-400W-DC (400 W DC-input power supply)

–

PWR-400W-AC (400 W AC-input power supply)

Note The 400 W AC-input power supply requires single-phase source AC.

Source AC can be out of phase between multiple power supplies

because all AC power supply inputs are isolated.

Note Both the AC-input power supply and the DC-input power supply

have status LEDs. Refer to Appendix A for descriptions of the LEDs

and their meanings.

Note The ME6524 switches support a combination of AC-input and

DC-input power supplies in the same chassis.

Pluggable transceivers supported • The chassis supports SFP transceivers.

• The 8 uplink ports support the following SFP transceiver types:

–

GLC-T—1000BASE-T

–

GLC-SX-MM—1000BASE-SX

–

GLC-LH-SM—1000BASE-LX/LH

–

GLC-ZX-SM—1000BASE-ZX

–

GLC-BX-D—1000BASE-BX10-D

–

GLC-BX-U—1000BASE-BX10-U

–

GLC-FE-100BX-D—100BASE-BX10-D

–

GLC-FE-100BX-U—100BASE-BX10-U

–

CWDM-SFP-xxxx—CWDM SFP transceivers

–

DWDM-SFP-xxxx—DWDM SFP transceivers

• The 24 downlink ports support the following SFP transceiver types:

–

GLC-T—1000BASE-T

–

GLC-SX-MM—1000BASE-SX

–

GLC-LH-SM—1000BASE-LX/LH

–

GLC-ZX-SM—1000BASE-ZX

–

GLC-BX-D—1000BASE-BX10-D

–

GLC-BX-U—1000BASE-BX10-U

–

GLC-FE-100BX-D—100BASE-BX10-D

–

GLC-FE-100BX-U—100BASE-BX10-U

Note CWDM and DWDM SFP transceivers are not supported in the

downlink ports.

Note Refer to Appendix B for SFP transceiver cabling distances and

additional information.

Table 1-1 Cisco ME 6524 Ethernet Switch (ME-C6524GS-8S) Features (continued)

Feature Description

1-4

Cisco ME 6500 Series Ethernet Switch Installation Guide

OL-8900-03

Chapter 1 Product Overview

Cisco ME 6524 Ethernet Switch (ME-C6524GS-8S)

Chassis front panel features

STATUS LED The STATUS LED indicates the system health.

• Green—The system is operating normally.

• Red—A fault has been detected in the system.

• Amber—System is booting up.

• Off—The system is not powered up.

PS1 (Power supply 1) LED The PS1 LED indicates the status of the power supply installed in power

supply bay 1.

• Green—Power supply is on and the input and output voltages are OK.

• Red—The power supply has a fault.

• Off—The power supply is off or is not installed.

PS2 (Power supply 2) LED The PS2 LED indicates the status of the power supply installed in power

supply bay 2.

• Green—Power supply is on and the input and output voltages are OK.

• Red—The power supply has a fault.

• Off—The power supply is off or is not installed.

FAN The FAN LED indicates the status of the individual fans in the fan tray.

• Green—Fan tray is operating normally.

• Red—One or more individual fans in the fan tray have failed.

RESET switch A recessed switch allows the user to reset the system.

Console port A single console port allows the user access to the command-line interface.

The console port has an RJ-45 connector.

USB ports The switch has two USB ports:

• Port 1 is a device port with a Type B USB connector. A standard

USB 1.1 host, such as a PC, can plug into this port.

• Port 2 is a host port with a Type A USB connector. A standard USB 1.1

device, such as flash memory, can plug into this port.

PCMCIA connector Type 2 CompactFlash devices can be plugged into this connector.

Table 1-1 Cisco ME 6524 Ethernet Switch (ME-C6524GS-8S) Features (continued)

Feature Description

Page is loading ...

Cisco Systems ME 6500 User manual

Brand: Cisco Systems

Model: ME 6500

Category: Network switches

Type: User manual

Download PDF

report

Cisco Systems ME 6500 User manual

Cisco Systems ME 6500 User manual

Related papers

Other documents