Gigabyte GA-8I865GVME User manual

GA-8I865GVME

Intel

®

Pentium

®

4 Processor Motherboard

User's Manual

Rev. 1003

12ME-865GVME-1003R

* The WEEE marking on the product indicates this product must not be disposed of with user's other household waste

and must be handed over to a designated collection point for the recycling of waste electrical and electronic equipment!!

* The WEEE marking applies only in European Union's member states.

Jul. 18. 2005

Motherboard

GA-8I865GVME

Motherboard

GA-8I865GVME

Jul. 18, 2005

Copyright

The trademarks mentioned in the manual are legally registered to their respective companies.

Notice

The written content provided with this product is the property of Gigabyte.

No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any

means without Gigabyte's prior written permission. Specifications and features are subject to

change without prior notice.

Product Manual Classification

In order to assist in the use of this product, Gigabyte has categorized the user manual in the

following:

 For quick installation, please refer to the "Hardware Installation Guide" included with the

product.

 For detailed product information and specifications, please carefully read the

"Product User Manual".

 For detailed information related to Gigabyte's unique features, please go to the

"Technology Guide" section on Gigabyte's website to read or download the information

you need.

For more product details, please click onto Gigabyte's website at www.gigabyte.com.tw

- 4 -

Table of Contents

GA-8I865GVME Motherboard Layout ............................................................................ 6

Block Diagram ................................................................................................................ 7

Chapter 1 Hardware Installation .................................................................................... 9

1-1 Considerations Prior to Installation .................................................................... 9

1-2 Feature Summary .......................................................................................... 10

1-3 Installation of the CPU and Heatsink ............................................................... 11

1-3-1 Installation of the CPU .......................................................................................... 11

1-3-2 Installation of the Heatsink .................................................................................. 12

1-4 Installation of Memory .................................................................................... 13

1-5 Installation of Expansion Cards ...................................................................... 15

1-6 I/O Back Panel Introduction ........................................................................... 16

1-7 Connectors Introduction .................................................................................. 17

Chapter 2 BIOS Setup ................................................................................................ 27

The Main Menu (For example: BIOS Ver. : E5) ....................................................... 28

2-1 Standard CMOS Features ............................................................................. 30

2-2 Advanced BIOS Features .............................................................................. 32

2-3 Integrated Peripherals ..................................................................................... 34

2-4 Power Management Setup ............................................................................. 37

2-5 PnP/PCI Configurations................................................................................. 38

2-6 PC Health Status ........................................................................................... 39

2-7 Frequency/Voltage Control ............................................................................. 40

2-8 Load Fail-Safe Defaults ................................................................................... 42

2-9 Load Optimized Defaults ................................................................................. 42

2-10 Set Supervisor/User Password ..................................................................... 43

2-11 Save & Exit Setup ......................................................................................... 44

2-12 Exit Without Saving ....................................................................................... 44

- 5 -

Chapter 3 Drivers Installation ...................................................................................... 45

3-1 Install Chipset Drivers .................................................................................... 45

3-2 Software Application ....................................................................................... 46

3-3 Software Information ....................................................................................... 46

3-4 Hardware Information ..................................................................................... 47

3-5 Contact Us ..................................................................................................... 47

Chapter 4 Appendix ................................................................................................... 49

4-1 Unique Software Utilities ................................................................................ 49

4-1-1 EasyTune 5 Introduction ..................................................................................... 49

4-1-2 Xpress Recovery2 Introduction ......................................................................... 50

4-1-3 Flash BIOS Method Introduction ........................................................................ 52

4-1-4 2- / 4- / 6- Channel Audio Function Introduction ............................................. 61

4-2 Troubleshooting ............................................................................................... 67

- 6 -

GA-8I865GVME Motherboard Layout

KB_MS

ATX_12V

CPU_FAN

Socket 478

AUDIO

Intel 865GV

SPDIF_IO

CODEC

VGA

LPT

USB

LAN

R_USB

Intel ICH5

F_PANEL

BIOS

PCI1

PCI2

EP82562G

F_AUDIO

F_USB2

F_USB1

SATA1

BATTERY

ATX

IDE1

FDD

SYS_FAN

PWR_LED

CD_IN

GA-8I865GVME

DDR1

DDR2

PCI3

COMA

IDE2

SATA0

LPC47M997

CLR_CMOS

- 7 -

Block Diagram

Line-Out

MIC

Pentium 4

Socket 478

CPU

CPUCLK+/-(133/200MHz)

33MHz

Host

Interface

Intel

865GV

GMCH

GMCHCLK (66MHz)

66MHz

48MHz

DDR 400/333/266MHz DIMM

14.318MHz

33MHz

LPC47M997

2 Serial ATA

ATA33/66/100

IDE Channels

Intel

ICH5

14.318MHz

BIOS

CODEC

Line-In

PCICLK

(33MHz)

3 PCI

PCI Bus

EP82562G

RJ45

8 USB

Ports

Dual Channel Memory

Floppy

PS/2 KB/Mouse

LPT Port

VGA

HCLK (133/200MHz)

COM Port

- 8 -

Hardware Installation- 9 -

English

1-1 Considerations Prior to Installation

Preparing Your Computer

The motherboard contains numerous delicate electronic circuits and components which can

become damaged as a result of electrostatic discharge (ESD). Thus, prior to installation, please

follow the instructions below:

1. Please turn off the computer and unplug its power cord.

2. When handling the motherboard, avoid touching any metal leads or connectors.

3. It is best to wear an electrostatic discharge (ESD) cuff when handling electronic components

(CPU, RAM).

4. Prior to installing the electronic components, please have these items on top of an antistatic

pad or within a electrostatic shielding container.

5. Please verify that the power supply is switched off before unplugging the power supply

connector from the motherboard.

Installation Notices

1. Prior to installation, please do not remove the stickers on the motherboard. These stickers

are required for warranty validation.

2. Prior to the installation of the motherboard or any hardware, please first carefully read the

information in the provided manual.

3. Before using the product, please verify that all cables and power connectors are connected.

4. To prevent damage to the motherboard, please do not allow screws to come in contact with

the motherboard circuit or its components.

5. Please make sure there are no leftover screws or metal components placed on the motherboard

or within the computer casing.

6. Please do not place the computer system on an uneven surface.

7. Turning on the computer power during the installation process can lead to damage to system

components as well as physical harm to the user.

8. If you are uncertain about any installation steps or have a problem related to the use of the

product, please consult a certified computer technician.

Instances of Non-Warranty

1. Damage due to natural disaster, accident or human cause.

2. Damage as a result of violating the conditions recommended in the user manual.

3. Damage due to improper installation.

4. Damage due to use of uncertified components.

5. Damage due to use exceeding the permitted parameters.

6. Product determined to be an unofficial Gigabyte product.

Chapter 1Hardware Installation

GA-8I865GVME Motherboard - 10 -

English

CPU  Socket 478 for Intel

®

Pentium

®

4 (Northwood, Prescott) with HT Technology

 Supports 800/533/400MHz FSB

 L2 cache varies with CPU

Chipset  Northbridge: Intel

®

865GV Chipset

 Southbridge: Intel

®

ICH5

Memory  2 DDR DIMM memory slots (supports up to 2GB memory)

 Supports dual channel DDR 400/333/266 DIMM

 Supports 2.5V DDR DIMM

Slots  3 PCI slots

IDE Connections  2 IDE connection (UDMA 33/ATA 66/ATA 100), allows connection of

4 IDE devices

FDD Connections  1 FDD connection, allows connection of 2 FDD devices

Onboard SATA  2 Serial ATA ports from ICH5 (SATA0, SATA1)

Peripherals  1 parallel port supporting Normal/EPP/ECP mode

 1 VGA port, 1 serial port (COMA)

 8 USB 2.0/1.1 ports (rear x 4, front x 4 via cable)

 1 front audio connector

 1 PS/2 keyboard port

 1 PS/2 mouse port

Onboard VGA  Built-in Intel

®

865GV Chipset

Onboard LAN  Onboard EP82562G chip (10/100 Mbit)

 1 RJ 45 port

Onboard Audio  ALC655 CODEC

 Supports Jack Sensing function

 Supports 2 / 4 / 6 channel audio

 Supports Line In (Rear Speaker Out) ; Line Out (Front Speaker Out) ;

MIC (Center/Subwoofer Speaker Out)

 SPDIF In/Out connection

 CD In connection

I/O Control  SMSC LPC47M997-NR

Hardware Monitor  System voltage detection

 CPU / System temperature detection

 CPU / System fan speed detection

BIOS  Use of licensed AWARD BIOS

 Supports Q-Flash

Additional Features  Supports @BIOS

 Supports EasyTune 5

(Note)

Overclocking  Over clock via BIOS (CPU/ AGP/ DDR/ PCI)

Form Factor  Micro ATX form factor; 24.4cm x 21.0cm

1-2 Feature Summary

(Note) EasyTune 5 functions may vary depending on different motherboards.

Hardware Installation- 11 -

English

1-3 Installation of the CPU and Heatsink

Before installing the CPU, please comply with the following conditions:

1. Please make sure that the motherboard supports the CPU.

2. Please take note of the one indented corner of the CPU. If you install the CPU in the wrong

direction, the CPU will not insert properly. If this occurs, please change the insert direction

of the CPU.

3. Please add an even layer of heat sink paste between the CPU and heatsink.

4. Please make sure the heatsink is installed on the CPU prior to system use, otherwise

overheating and permanent damage of the CPU may occur.

5. Please set the CPU host frequency in accordance with the processor specifications. It is not

recommended that the system bus frequency be set beyond hardware specifications since it

does not meet the required standards for the peripherals. If you wish to set the frequency

beyond the proper specifications, please do so according to your hardware specifications

including the CPU, graphics card, memory, hard drive, etc.

HT functionality requirement content :

Enabling the functionality of Hyper-Threading Technology for your computer system requires all

of the following platform components:

- CPU: An Intel

®

Pentium 4 Processor with HT Technology

- Chipset: An Intel

®

Chipset that supports HT Technology

- BIOS: A BIOS that supports HT Technology and has it enabled

- OS: An operation system that has optimizations for HT Technology

1-3-1 Installation of the CPU

Fig. 1

Position lever at a 90 degree angle.

Fig. 2

A gold-colored triangle is marked one edge of the CPU. Please align this

edge with the socket edge closest to the CPU lever. Gently place the CPU

into position making sure that the CPU pins fit perfectly into their holes.

Once the CPU is positioned into it socket, place one finger down on the middle

of the CPU and gently press the metal lever back into its original position.

Socket lever

Please use extra care when installing the CPU. The CPU will not fit if positioned incorrectly.

Rather than applying force, please change the positioning of the CPU.

GA-8I865GVME Motherboard - 12 -

English

1-3-2 Installation of the Heatsink

The heat sink may adhere to the CPU as a result of hardening of the heat sink paste. To prevent

such an occurrence, it is suggested that either thermal tape rather than heat sink paste be used for

heat dissipation or using extreme care when removing the heat sink.

Fig.1

Before installing the heat sink, please first add an even layer of heat sink

paste on the surface of the CPU. Install all the heat sink components (Please

refer to the heat sink manual for detailed installation instructions).

Fig.2

Please connect the heat sink power connector to the CPU_FAN connector

located on the motherboard so that the heat sink can properly function to

prevent CPU overheating.

Hardware Installation- 13 -

English

Before installing the memory modules, please comply with the following conditions:

1. Please make sure that the memory used is supported by the motherboard. It is

recommended that memory of similar capacity, specifications and brand be used.

2. Before installing or removing memory modules, please make sure that the computer power

is switched off to prevent hardware damage.

3. Memory modules have a foolproof insertion design. A memory module can be installed in

only one direction. If you are unable to insert the module, please switch the direction.

1-4 Installation of Memory

The motherboard supports DDR memory modules, whereby BIOS will automatically detect memory capacity

and specifications. Memory modules are designed so that they can be inserted only in one direction. The

memory capacity used can differ with each slot.

Notch

DDR

Fig.1

The DIMM socket has a notch, so the DIMM memory module can only

fit in one direction. Insert the DIMM memory module vertically into the

DIMM socket. Then push it down.

Fig.2

Close the plastic clip at both edges of the DIMM sockets to lock the

DIMM module.

Reverse the installation steps when you wish to remove the DIMM

module.

GA-8I865GVME Motherboard - 14 -

English

Dual Channel DDR

GA-8I865GVME supports the Dual Channel Technology. After operating the Dual Channel Technology, the

bandwidth of Memory Bus will add double up to 6.4GB/s(DDR400) or 5.3GB/s(DDR333).

GA-8I865GVME includes 2 DIMM sockets, and each Channel has one DIMM socket as following:

Channel A : DDR 1

Channel B : DDR 2

If you want to operate the Dual Channel Technology, please note the following explanations due to the

limitation of Intel chipset specifications.

1. Dual channel memory cannot be used if one DDR memory modules are installed.

2. If two DDR memory modules are installed, please use memory of the same storage capacity in

order to use dual channel memory and for BIOS to detect all the DDR memory modules.

The following table is for Dual Channel Technology combination: (DS: Double Side, SS: Single Side)

2 memory modules

DDR 1 DDR 2

DS/SS DS/SS

Hardware Installation- 15 -

English

1-5 Installation of Expansion Cards

You can install your expansion card by following the steps outlined below:

1. Read the related expansion card's instruction document before install the expansion card into the

computer.

2. Remove your computer's chassis cover, screws and slot bracket from the computer.

3. Press the expansion card firmly into expansion slot in motherboard.

4. Be sure the metal contacts on the card are indeed seated in the slot.

5. Replace the screw to secure the slot bracket of the expansion card.

6. Replace your computer's chassis cover.

7. Power on the computer, if necessary, setup BIOS utility of expansion card from BIOS.

8. Install related driver from the operating system.

Installing a AGP VGA card:

Please carefully pull out the small white-

drawable bar at the end of the AGP slot

when you try to install/uninstall the VGA

card. Please align the VGA card to the

onboard AGP slot and press firmly down on

the slot. Make sure your VGA card is locked

by the small white-drawable bar.

GA-8I865GVME Motherboard - 16 -

English

1-6 I/O Back Panel Introduction

You can use audio software to configure 2-/4-/6-channel audio functioning.

PS/2 Keyboard and PS/2 Mouse Connector

To install a PS/2 port keyboard and mouse, plug the mouse to the upper port (green) and the keyboard to the

lower port (purple).

Parallel Port

The parallel port allows connection of a printer, scanner and other peripheral devices.

COMA (Serial Port)

Connects to serial-based mouse or data processing devices.

VGA Port

Monitor can be connected to VGA port.

USB port

Before you connect your device(s) into USB connector(s), please make sure your device(s) such as

USB keyboard, mouse, scanner, zip, speaker...etc. have a standard USB interface. Also make sure

your OS supports USB controller. If your OS does not support USB controller, please contact OS ven

dor for possible patch or driver upgrade. For more information please contact your OS or device(s)

vendors.

LAN Port

The provided Internet connection provides data transfer speeds of 10/100Mbps.

Line In

Devices like CD-ROM, walkman etc. can be connected to Line In jack.

Line Out

Connect the stereo speakers or earphone to this connector.

MIC In

Microphone can be connected to MIC In jack.

Hardware Installation- 17 -

English

1-7 Connectors Introduction

1) ATX_12V

2) ATX (Power Connector)

3) CPU_FAN

4) SYS_FAN

5) FDD

6) IDE1 / IDE2

7) SATA0 / SATA1

8) PWR_LED

9) BATTERY

10) F_PANEL

11) F_AUDIO

12) CD_IN

13) SPDIF_IO

14) F_USB1 / F_USB2

15) CLR_CMOS

13

10

7

6

9

11

12

4 14 8513

2

15

GA-8I865GVME Motherboard - 18 -

English

1/2) ATX_12V/ATX (Power Connector)

With the use of the power connector, the power supply can supply enough stable power to all the

components on the motherboard. Before connecting the power connector, please make sure that all

components and devices are properly installed. Align the power connector with its proper location on

the motherboard and connect tightly.

The ATX_12V power connector mainly supplies power to the CPU. If the ATX_12V power connector

is not connected, the system will not start.

Caution!

Please use a power supply that is able to handle the system voltage requirements. It is

recommended that a power supply that can withstand high power consumption be used (300W or

greater). If a power supply is used that does not provide the required power, the result can lead to an

unstable system or a system that is unable to start.

34

12

Pin No. Definition

1 GND

2 GND

3 +12V

4 +12V

Pin No. Definition

1 3.3V

2 3.3V

3 GND

4 +5V

5 GND

6 +5V

7 GND

8 Power Good

9 5V SB (stand by +5V)

10 +12V

11 3.3V

12 -12V

13 GND

14 PS_ON(soft on/off)

15 GND

16 GND

17 GND

18 -5V

19 +5V

20 +5V

1

10

11

20

Hardware Installation- 19 -

English

3/4) CPU_FAN / SYS_FAN (Cooler Fan Power Connector)

The cooler fan power connector supplies a +12V power voltage via a 3-pin power connector and

possesses a foolproof connection design.

Most coolers are designed with color-coded power connector wires. A red power connector wire

indicates a positive connection and requires a +12V power voltage. The black connector wire is the

ground wire (GND).

Please remember to connect the power to the cooler to prevent system overheating and failure.

Caution!

Please remember to connect the power to the CPU fan to prevent CPU overheating and failure.

1

Pin No. Definition

1 GND

2 +12V

3 Sense

5) FDD (FDD Connector)

The FDD connector is used to connect the FDD cable while the other end of the cable connects to the

FDD drive. The types of FDD drives supported are: 360KB, 720KB, 1.2MB, 1.44MB and 2.88MB.

Please connect the red power connector wire to the pin1 position.

1

2

33

34

CPU_FAN / SYS_FAN

GA-8I865GVME Motherboard - 20 -

English

6) IDE1 / IDE2 (IDE Connector)

An IDE device connects to the computer via an IDE connector. One IDE connector can connect to one

IDE cable, and the single IDE cable can then connect to two IDE devices (hard drive or optical drive). If

you wish to connect two IDE devices, please set the jumper on one IDE device as Master and the other

as Slave (for information on settings, please refer to the instructions located on the IDE device).

2

40

1

39

7) SATA0 / SATA1 (Serial ATA Connector)

Serial ATA can provide up to 150MB/s transfer rate. Please refer to the BIOS setting for the Serial ATA

and install the proper driver in order to work properly.

Pin No. Definition

1 GND

2 TXP

3 TXN

4 GND

5RXN

6 RXP

7 GND

71

IDE2 IDE1

Page is loading ...

Gigabyte GA-8I865GVME User manual

Gigabyte GA-8I865GVME User manual

Related papers

Other documents