Page is loading ...
TE-FW210
TE-FW310
Dimensions
Unit: mm
(1) (2) (3)
The subwoofer is heavy. Attach it firmly to a solid thick baffle-board.
Do not continuously use the speaker system beyond the peak power handling capacity.
Keep credit cards, watches, recorded tapes etc. with magnetic coding away from the speaker system to
prevent damage caused by the magnets in the speakers.
Clean the apparatus with soft, damp cloth. Never use substances such as alcohol, chemicals or
household cleaners on the apparatus.
Thank you for purchasing the subwoofer speaker. For the secure installation and perfect operation of
your speaker, please read and understand all instructions before you use the apparatus.
Important
◆
◆
◆
◆
Check and identify the contents of your package:
(1) Subwoofer ×1
(2) Installation manual ×1
(3) Screw (Ø5×30) ×8
What’s in the box
★ Accessories are subject to change wi thout notice.
TE-FW210 TE-FW310
★ Design and specifications are subject to change without notice.
Nominal Diameter:
Mounting Depth:
Rated Power (RMS):
MAX. Music Power:
Nominal Impedance:
Frequency Response:
Sensitivity (SPL/1W/1m):
Free Air Resonance (Fs):
Suspension Compliance (Cms):
Moving Mass (Mms):
Mechanical “Q” (Qms):
Electrical “Q” (Qes):
Total Speaker “Q” (Qts):
Equivalent Volume (Vas):
DC Resistance (Re):
Effective Piston Area (Sd):
Force Factor (BL):
Reference Efficiency (No):
Voice Coil (V.C.):
Magnet Mass:
Subwoofer Mass:
10 in (256 mm)
4.4 in (112 mm)
200 watts
1000 watts
4 ohms
63-2000 Hz
86 dB
63 Hz
73.421 mkm/N
84.597 g
5.177
1.221
0.988
0.44 cu ft (12.48 l)
3.4 ohms
2
53.6 sq in (346 cm )
9.721 Txm
0.257%
Φ49.5 mm, ASV
29.3 oz (830.6 g)
Approx. 2.8 kg
SPECIFICATIONS:
12 in (300mm)
5.4 in (136mm)
250 watts
1500 watts
4 ohms
56-1500 Hz
87 dB
56 Hz
40.954 mkm/N
191.304 g
4.957
0.906
0.766
0.61 cu ft (17.34 l)
3.4 ohms
2
84.6 sq in (546 cm )
16.018 Txm
0.340%
Φ49.5 mm, BASV
42.5 oz (1204.8 g)
Approx. 4.1 kg
CAR SUBWOOFER SPEAKERS
TE-FW210
INSTRUCTIONS
TE-FW310
◆ One Amplifier and
One Subwoofer
1 ch Output
◆ One Amplifier and Two Subwoofers
1 ch Output
You can mount the subwoofer on the rear tray.
(Fig.1)
★ Set the wiring firmly on the floor of the vehicle,
taking the utmost care not to break wires while
installing.
Option 1: Mount on rear tray
Turn off the car ignition key.
★ If the power is on, the click noise generated by
the connection may damage the subwoofer.
Cut out the mounting template from the packing
box and paste it onto the location selected for
mounting the subwoofer.
Mark the cut-off hole and the 8 bolt holes. (Fig.2)
Cut out the marked area and drill the bolt holes.
(Fig.3)
Fig.2 Fig.3
Fig.1
Installat io n
Fig.4
Speaker wire
(not supplied)
10~15mm
Amplifier
2 ch Output
Fig.5 Fig.6 Fig.7
Connect the subwoofer to the amplifier. (Fig.4-
Fig.7)
★ The TE-FW210 / TE-FW310 has an nominal
impedance of 4 ohm. Make sure that the output
impedance of the amplifier ’s speaker terminal is
rated at 4 ohms.
★ Consult the diagram. Be sure to connect
corresponding terminals, i.e. “+” to “+” and “-” to “-
”. Connection with reversed polarity will degrade
the quality of reproduction.
5.
1.
2.
3.
4.
Troubleshooting
Sympton
Probable cause
Remedy
No output
Audio cycle
on and off
no output
Distorted
output
Poor bass
response
Source or amplifier not turned on
Audio input not connected or no output
from source
Speaker wires not connected
Speaker damaged
Loose or poor audio input
Preamp volume set too high, exceeding
maximum input capability of amplifier
Impedance load to amplifier too low
Shorted speaker wires
Speaker damaged
Speakers wired with wrong polarity
causing cancellation at low frequencies
Check source or amplifier and repair as needed
Check RCA connections and signal integrity,
repair or replace as needed
Check speaker wires and repair or replace as needed
Check speaker impedance load, if below 1 ohm
rewire the speakers to achieve a higher impedance
Check speaker wire connections and repair or
replace as needed
Check volume of preamp and adjust appropriately,
Check speaker impedance load, if below 1 ohm
Rewire the speakers to achieve a higher impedance
Check speaker wire connections and repair or
replace as needed
Check system with known working speaker and
repair or replace as needed
Check speaker polarity and repair as needed
4Ω 4Ω
Amplifier
2Ω
Amplifier
4Ω
Amplifier
a
b
c
d
h
D1
D2
TE-FW210
TE-FW310
6.7 in (170mm)
11.2 in (285mm)
14.2 in (360mm)
15.4 in (391mm)
13.4 in (340mm)
2.7 in (68mm)
9.3 in (236mm)
8.3 in (210mm)
13.4 in (340mm)
14.6 in (370mm)
17.1 in (435mm)
14.0 in (355mm)
2.7 in (68mm)
11.0 in (280mm)
Fig.8
Mount the subwoofer into the rear tray with the supplied screws. (Fig.8)
6.
If the subwoofer cannot be mounted on the car, place it in a sealed enclosure. (Fig.9-
Fig.10)
All recommended enclosures have been designed and thoroughly tested.
Option 2: Install in a sealed enclosure
Fig.9
Connect the subwoofer to the amplifier. (See step 5 of “Option 1: Mount on rear tray”
section).
Install the subwoofer into the sealed enclosure with the supplied screws.
Fig.10
3
5
1
6
4
2
1
3
4
6
5
a
b
h
c
d
a
d
b
d
h
d
c
1 6
board thickness: 15mm.
2
a
b
h
c
/
