Powerplus POWXG6310 Owner's manual

Brand: Powerplus

Model: POWXG6310

Type: Owner's manual

POWXG6310 EN

1 INTENDED USE ............................................................................... 3

2 DESCRIPTION (FIG A, B & C) ........................................................ 3

3 PACKAGE CONTENT LIST ............................................................. 3

4 EXPLANATION OF USED SYMBOLS ............................................ 4

5 SAFETY INSTRUCTIONS ................................................................ 4

5.1 Training.................................................................................................................... 4

5.2 Preparation .............................................................................................................. 4

5.3 Operation ................................................................................................................. 5

5.3.1 General ..................................................................................................................... 5

5.3.2 Additionally when the machine is operating automatically ......................................... 5

5.3.3 Maintenance and storage .......................................................................................... 5

5.3.4 Recommendations .................................................................................................... 5

6 SPECIAL SAFETY REGULATIONS FOR ROBOTIC

LAWNMOWER ............................................................................................. 6

6.1 Robotic lawnmower safety warning ....................................................................... 6

6.2 Battery/Battery charger safety warnings ............................................................... 6

7 OPERATION ..................................................................................... 7

7.1 Lawn preparation .................................................................................................... 7

7.2 Charging station placement and connection (Fig. 5) ............................................ 7

7.3 Charging the lawnmower ........................................................................................ 8

7.4 Setting up the perimeter wire (Fig 3, Fig 4 and Fig 5) ........................................... 8

7.5 Setting up the robotic lawnmower ....................................................................... 10

7.5.1 Blade height adjusting knob (2) ............................................................................... 10

7.5.2 Password ................................................................................................................ 10

7.5.3 Start the mower ....................................................................................................... 10

7.5.4 Stop the robotic mower ........................................................................................... 11

7.5.5 Change password ................................................................................................... 11

7.5.6 Stand-by modus ...................................................................................................... 11

7.6 Smartphone application (APP) ............................................................................. 12

7.6.1 Download the APP .................................................................................................. 12

7.6.2 Add your mower into the APP ................................................................................. 12

POWXG6310 EN

7.6.3 Connect the APP on two way .................................................................................. 12

7.7 Control panel information (Fig 7) ......................................................................... 13

7.7.1 Light status ............................................................................................................. 13

7.7.2 Buttons ................................................................................................................... 13

8 TROUBLE SHOOTING .................................................................. 13

8.1 Fault codes ............................................................................................................ 13

8.1.1 Fault codes (when outside charging station)............................................................ 13

8.1.2 Fault codes (when charging) ................................................................................... 14

8.1.3 Clear the fault code ................................................................................................. 14

8.2 Mower does not work ........................................................................................... 14

8.3 Troubleshooting of the application ...................................................................... 15

9 MAINTENANCE ............................................................................. 18

9.1 General maintenance plan .................................................................................... 18

9.2 Cleaning the mower .............................................................................................. 18

9.3 Blade replacement (Fig 8) ..................................................................................... 19

9.4 Storage .................................................................................................................. 19

10 TECHNICAL DATA ........................................................................ 19

11 NOISE ............................................................................................. 20

12 WARRANTY ................................................................................... 21

13 ENVIRONMENT ............................................................................. 21

13.1 Battery pack .......................................................................................................... 21

POWXG6310 EN

ROBOTIC LAWNMOWER 18V 5.0AH 1000M²

POWXG6310

1 INTENDED USE

The robotic lawnmower is designed to mow grass ground areas where the slope is less than

17°. No collection of grass is required, and small particles of cut grass will reduce the need of

fertilizers. Before you can start mowing with your robotic lawnmower, you have to prepare the

lawn initially, find a proper place for your charging station and set up the perimeter wire to

define the borders of the mowing area.

WARNING! For your own safety, read this manual and the general safety

instructions carefully before using the appliance. Your power tool should

only be given to other users together with these instructions.

2 DESCRIPTION (FIG A, B & C)

1. Stop button

2. Blade height adjust knob

3. Control panel

4. Rain sensor

5. Handle

6. On/Off switch

7. Blades

8. Wheels

9. Caster wheels

10. Charging pins

11. Mounting holes

12. Charging indicator

13. Charging socket

14. Terminals for perimeter wire

15. Power adapter

16. Peg for charging station

17. Spare blades & screws

18. Wire connector

3 PACKAGE CONTENT LIST

 Remove all packing materials.

 Remove remaining packaging and transit supports (if existing).

 Check the completeness of the packing content.

 Check the appliance, the power cord, the power plug and all accessories for transportation

damages.

 Keep the packaging materials as long as possible till the end of the warranty period.

Dispose it into your local waste disposal system afterwards.

WARNING: Packing materials are no toys! Children must not play with

plastic bags! Danger of suffocation!

1 x robotic lawnmower

1 x charging station

1 x power adapter

4 x peg for charging station

6 x spare blades & screws

1 x wire connector

180 x installation peg

150m perimeter wire

1 x manual

1 x paper gauge

When parts are missing or damaged, please contact your dealer.

POWXG6310 EN

4 EXPLANATION OF USED SYMBOLS

Read manual before use.

Always keep a safe

distance from the machine

when operating.

Never use the machine

when persons, children or

pets are in the cutting area.

Always remove the disabling

device（On/Off switch） before

working on or lifting the

machine.

Do not sit or ride on the

machine.

The product complies with the

applicable European directives

and an evaluation method of

conformity for these directives

was done.

At the end of its lifecycle,

the device must not be

disposed of with normal

household waste. Ensure

that the device is disposed

of in accordance with local

regulations.

Li-ion battery. This product has

been marked with a symbol

relating to ‘separate collection’

for all battery packs. It will then

be recycled or dismantled in

order to reduce the impact on

the environment.

Guaranteed sound power

level.

5 SAFETY INSTRUCTIONS

IMPORTANT: READ CAREFULLY BEFORE USE! KEEP FOR FUTURE

REFERENCE!

5.1 Training

 Read the instructions carefully. Be familiar with the controls and the proper use of the

machine.

 Never allow people unfamiliar with these instructions or children to use the machine. Local

 regulations may restrict the age of the operator.

 The operator or user is responsible for accidents or hazards occurring to other people or

their property.

 Never allow children, persons with reduced physical, sensory or mental capabilities or lack

of experience and knowledge or people unfamiliar with these instructions to use the

machine, local regulations may restrict the age of the operator.

5.2 Preparation

 Ensure the correct installation of the charging station and boundary wire as instructed.

POWXG6310 EN

 Periodically inspect the area where the machine is to be used and remove all stones,

sticks,

 wires, bones, and other foreign objects.

 Periodically visually inspect to see that the blades, blade bolts and cutter assembly are not

worn or damaged. Replace worn or damaged blades and bolts in sets to preserve

balance.

 On multi-spindle machines, take care as rotating one blade can cause other blades to

rotate.

5.3 Operation

5.3.1 General

 Never operate the machine with defective guards, or without safety devices.

 Do not put hands or feet near or under rotating parts.

 Never pick up or carry an machine while the motor is running.

 Remove (or Operate) the disabling device from the machine

o before clearing a blockage;

o before checking, cleaning or working on the machine;

o after striking a foreign object to inspect the machine for damage;

o if the machine starts to vibrate abnormally, and to check for damage

before restarting.

5.3.2 Additionally when the machine is operating automatically

 Do not leave the machine to operate unattended if you know that there are pets, children

or people in the vicinity.

5.3.3 Maintenance and storage

 Keep all nuts, bolts, and screws tight to be sure the machine is in safe working condition.

 Replace worn or damaged parts for safety.

 Ensure that only replacement cutting means of the right type are used.

 Ensure that batteries are charged using the correct charger recommended by the

manufacturer. Incorrect use may result in electric shock, overheating or leakage of

corrosive liquid from the battery.

 In the event of leakage of electrolyte flush with water/neutralizing agent, seek medical help

if it comes into contact with the eyes, etc.

 Servicing of the machine should be according to manufacturers’ instructions.

5.3.4 Recommendations

 Connect the machine and/or its peripherals only to a supply circuit protected by a residual

current device (RCD) with a tripping current of not more than 30 mA.

 Avoid using the machine and its peripherals in bad weather conditions especially when

there is a risk of lightning.

 Read all safety warnings and all instructions. Failure to follow all warnings and instructions

may result in electric shock, fire and/or serious injury. Save all warnings and instructions

for future reference. The term "power tool" in the warnings refers to your mains operated

(corded) power tool or battery operated (cordless) power tool.

POWXG6310 EN

6 SPECIAL SAFETY REGULATIONS FOR ROBOTIC LAWNMOWER

6.1 Robotic lawnmower safety warning

 Never allow people unfamiliar with these instructions or children to use the machine.

 The use of the appliance by persons (including children) who have limited physical,

sensory or mental abilities or lack the necessary experience and knowledge is prohibited

unless they have been supervised at work by a person responsible for their safety and

have received prior training in the use of the appliance. Do not allow children to play with

the appliance. The appliance is not a toy.

 Wear long pants and sturdy shoes when nearby or inside the work area while the lawn

mower is operating.

 Do not ride on the lawn mower, push the lawn mower, or use it for anything other than its

intended purpose, otherwise you or someone else may be injured.

 Do not use automatic lawn watering systems while the lawn mower is operating, because

the watering equipment may become damaged and the likelihood of water penetrating into

the lawn mower is greatly increased. Adjust the work time of the lawn mower so that the

watering systems and the lawn mower do not operate at the same time.

 Ensure the correct installation of the charging station and boundary wire as instructed in

this manual.

 Periodically inspect the area where the machine is to be used and remove all stones,

sticks, wires, branches and other foreign objects.

WARNING: The machine can be dangerous if used improperly.

WARNING: When carrying the lawn mower, make sure to carry it by the

designed areas. If you carrying the lawn mower in any other way, you risk

injury from the blades or charging socket of the lawn mower.

6.2 Battery/Battery charger safety warnings

 Protect the battery charger from rain and moisture. The penetration of water in a battery

charger increases the risk of electric shock.

 Recharge only with the charger specified by the manufacturer. A charger that is suitable

for one type of battery pack may create a risk of fire when used with another battery pack.

 Do not charge other batteries. The battery charger is suitable only for charging lithium ion

batteries of POWXG6310. Otherwise danger, fire and explosion may occur.

 Keep the battery charger clean. Contamination may cause the danger of electric shock.

 Check the battery charger, cable and plug each time before using. Do not use the battery

charger when defects are detected. Do not open the battery charger yourself and have it

repaired only by qualified personnel using original spare parts. Damaged battery chargers,

cables and plugs increase the risk of electric shock.

 Do not operate the battery charger on easily inflammable surfaces (e. g. paper, textiles,

etc.) or in combustible environments. There is danger of fire due to the heating of the

battery charger during charging.

 Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact

accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical

help. Liquid ejected from the battery may cause irritation or burns.

 Do not open the battery yourself. There is danger of a short circuit.

 Protect the battery against heat, e.g., including against continuous sun irradiation and fire.

There is a danger of explosion.

 Do not short-circuit the battery. There is a danger of explosion.

POWXG6310 EN

 In case of damage and improper use of the battery, vapours may be emitted. In case of

complaints, provide for fresh air and consult a physician. The vapours can irritate the

respiratory system.

7 OPERATION

7.1 Lawn preparation

Before operating the robotic lawnmower, ensure that the mowing area is free of pets, kids or

objects. Remove stones, loose pieces of wood, wire, cables from the lawn. Make sure that the

lawn height is 50 mm or less. If the height is more than that, cut the lawn to a height of 50

using a standard lawnmower. Cut the area where you intend to lay the perimeter wire to the

lowest setting you have with your conventional mower.

7.2 Charging station placement and connection (Fig. 5)

Find the best place for your charging station (if possible out of the sun), where your robotic

lawnmower will return to get charged.

1. Take the robotic lawnmower from the charging station and place the charging

station on level ground outside the mowing area.

Make sure

 that you have a straight 1.5 m track in front of the charging station.

 that the base stand is firmly on the ground and does not bend.

 not to put the charging station in confined spaces.

 that you have 1.0 m of free space perpendicular to the rear the charging

station.

 that the next power socket is within 6 meters.

 that the charging station is not placed in direct sunlight, if possible.

It is recommended to place the charging as close to the power supply as possible. The total

length of the power cable is 6 m.

Note: Your robotic lawnmower can only automatically return to the charging

station counter-clockwise.

Note: When your robotic lawnmower receives direct sunlight for a

prolonged period of time the battery can get too hot and will not function

correctly.

2. Fix the charging station with the four supplied pegs.

3. Connect the charging socket to the charging adaptor.

4. Connect the charging adaptor to the power supply (Fig 1).

Make sure that the power supply is

 close to the charging station

 protected from rain, e.g. under a roof

 protected from direct sunlight, if possible

 Once connected you should now see a red light (power) on the charging

station.

 The green light (work) on the charging station indicates wiring conditions of the

charging station. When the green light flashes, the wire loop is interrupted and

the mower cannot work.

Note: When mower is charging the green light on charging station will also

flash. If mower is not in charging station and green light on charging station

POWXG6310 EN

flashes this will indicate that wire loop is interrupted, and then mower will not

work.

7.3 Charging the lawnmower

Your robotic lawnmower´s battery may be charged to a certain degree on delivery, but it´s

recommended to fully charge the battery of the lawnmower before use. To charge your robotic

lawnmower follow these steps:

1. Switch the robotic lawnmower on. The On/Off switch (6) is located at the bottom

side of the robotic lawnmower (FIG A and Fig 2).

Note: Your robotic lawnmower will not charge when it is not turned on.

Note: The robotic lawnmower will enter a self-checking state (normally within

5 seconds) after entering the password or when the power is interrupted

during mowing or charging (indicated by a flashing status light). If the mower

is in a self-check state, you will not hear a sound when pressing a button and

the buttons won´t work.

2. Slide the robotic lawnmower into the charging station to charge.

3. Check the indicator on the charging station. The red power light turns up and the

robotic lawnmower charges (green light flashes). If the power light does not light up,

you should check the mains plug of the power supply is plugged in properly and that

the mower is in the station correctly.

4. It takes about 180 minutes to get the battery fully loaded.

7.4 Setting up the perimeter wire (Fig 3, Fig 4 and Fig 5)

The wire defines the borders of the mowing area. Everything in the inner area belongs to the

mowing area, everything in the outer area doesn´t belong to the mowing area. The wire also

serves to mark obstacles and exclude them from the mowing area.

1. Feed the end of the perimeter wire through the groove on the front at the bottom

side of the charging station, until it appears on the rear side (Fig 3).

2. Carefully strip off 10-15 mm of the insulation of the wire.

Note: You should keep a length of 15-20 cm at start and the end of the wire for

operating and handling the wire.

3. Connect the wire to the right hand (black) B terminal of the charging station (Fig 4).

4. Start installing the perimeter wire from the charging station in a clockwise direction

(Fig 5). Pull the wire from the coil, tauten and fix it with one peg. Use a mallet to

insert them in the lawn. Ensure the wire is straight and in line with the charging

station groove for 1.5 m.

5. Recommended distance between pegs is 50 to 75 cm (max).

6. Continue to set the wire around the perimeter of the mowing area.

7. For a more accurate perimeter, we advise that you leave less than 75 cm between

pegs when wiring objects (like flower beds, bushes, trees and other items).

Loose wire can be cut during mowing. Make sure the wire is flat to the ground.

Use additional pegs where the wire is slack. The wire is taut before placing the

next peg (if you can place a couple of fingers under the wire this is not taut

enough). Increase the number of pegs at a corner.

POWXG6310 EN

Note: If the mowing area borders against a flat path or a surface that is level

with the lawn, your robotic lawnmower will be able to run over it. In such

cases the perimeter wire should be positioned right up to the edge of the lawn

(approx. 10 cm). This is not applicable for gravel, as your robotic lawnmower

could hit a stone or get stuck in the gravel.

Note: When installing the wire around the perimeter of pond of water, the

distance between the wire and the edge of the pond must be more than 75 cm,

because of safety reasons. In case there is a power cut your robotic

lawnmower will stop after not noticing the wire for 100 cm.

Note: When marking objects remember there must be at least 75 cm distance

between two objects. Leaving less distance than this will cause some

interference.

Note: Do not install the wire on the slope (max 17° or 30%), or your mower

could be slip out the boundary easily.

Note: The robotic lawnmower cannot go through distance less than 60cm.

8. Encircling obstacles (Fig 5). Mark out permanent objects you do not want the mower

to run over, e.g. roots, ponds, flower beds or rocks. This will prevent your robotic

lawnmower colliding with objects or going straight into them.

To mark a obstacle:

a. Run the wire from the lawn perimeter to the object.

b. Continue round the objects in a clockwise direction. When going around

the object use more pegs. So they are closer than 75 cm.

c. Return the wire back to the lawn perimeter. Ensure the distance from the

wire around the object and lawn perimeter wire is at least 75 cm.

Please ensure that the two parallel wires leading to and from the marked object are

as close as possible by placing the wire under the same side of the peg. This will

make the wire undetectable to your robotic lawnmower. Please ensure that the

wires do not cross over each other at any point..

Note: Remember to leave 30 cm around the object to the wire! If objects are

less than 75 cm from the lawn edge, surround the object when installing the

wire, leaving the object outside of the lawn cutting area.

9. When the perimeter wire has been laid around the entire cutting area, cut the wire

and strip 10-15 mm of insulation off.

10. Connect the wire to the left hand (red) terminal (Fig 4).

Note: Observe the distances in Fig 6 if a second mower is used next or on the

property.

POWXG6310 EN

7.5 Setting up the robotic lawnmower

When your robotic lawnmower´s battery is fully loaded, you can start setting up the

lawnmower.

Note: The maximum waiting time is up to 3 minutes for the mower receiving

the GPS signal after the initialization.

7.5.1 Blade height adjusting knob (2)

First you have to set up the cutting height. Turn the knob to adjust the blades to a appropriate

cutting height. They can be adjusted between 25 mm-50 mm manually.

7.5.2 Password

The robotic lawnmower is password protected. To start the lawnmower for the first time, you

have to enter the password. Factory default password is 1111. You can enter the password by

the panel on the top side of the mower.

See Fig 7, panel on the top side, GPS light marked with a rectangle.

1. Press HOME (for password number “1”). The GPS light flashes 3 times.

2. Press HOME(for password number “1”) a second time. The GPS light flashes 2

times.

3. Press HOME(for password number “1”) a third time. The GPS light flashes 1 time.

4. Press HOME (for password number “1”)a fourth time. The GPS light will work

according to the real status of the satellite's signal (it works when the satellite's

signal is lighting up continuous ,otherwise ,it turns off).

Note: When no password is entered, the GPS light flashes 4 times. You cannot

control the mower through panel after entering wrong password.

7.5.3 Start the mower

If you have entered the correct password:

1. Press START + OK in order within 5 seconds: the mower will start working when the

mowing conditions are allowed after self-check status.

The mowing conditions are:

1. The temperature of the mower is within working temperature;

2. There is no water on the rainy detector;

3. The battery is over 30% capacity.

4. The mower is charging or detects itself in the boundaries.

5. The GPS light is on.

Note: It’s necessary to enter the password before pressing the buttons.

You can operate the mower with or without the change of the automatic starting time by the

following combinations:

Button

Action

START + OK (within 5 seconds)

The mower starts the work task.

HOME + OK (within 5 seconds)

The mower stops the work task and returns to the

charging station.

START + HOME at the same time

Change the password

POWXG6310 EN

7.5.4 Stop the robotic mower

You can always stop your robotic mower by pressing the EMERGENCY STOP button (1) on

the top.

The robotic mower will stop immediately.

Note: The stop button has the highest priority, the robotic lawnmower will

stop running in any case.

To restart the mower after pressing the STOP button:

1. Make sure that all conditions for starting the mower are met (for the mower itself and

in the mowing area).

2. Enter the password.

3. Press START + OK at the same time to leave emergency stop state.

4. Press START + OK within 5 seconds to restart the mower.

Remark:

1. If GPS light is off, means sat signal is not ready, mower must wait for sat signal.

2. If GPS light is blinking as a fault state mentioned in the manual, means some fault

state still exists and mower cannot work.

3. If GPS light is blinking continuously, means panel is locked. You need to enter the

password to unlock the panel. When sat signal is ready (GPS light is on

continuously), mower can start to work again.

When the mower stops working, restart the mower by turning the power switch Off and On

again, insert password and start by pressing START and then OK (within 5 seconds).

7.5.5 Change password

You can change the password from default (“1111”) to your own combination of 4 numbers.

The password combination consists 4 digits from 1 to 3.

1. Press START and HOME at the same time, the GPS light flashes 4 times

2. Enter a new password that consists of four numbers, each number pressed needs

to be within 3 seconds. The flashing situation of the GPS light is the same like

“When entering the default password ”.

3. Enter the new password a second time, after pressing fourth number, the GPS light

will work according to the real status of the satellite's signal (it works when the

satellite's signal is lighting up continuous ,otherwise ,it turns off).

 If two passwords are equal, the change is successful, the GPS light is still on.

Otherwise, two lights flash at the same time(change failed).

Note: Press HOME (for password number “1”), press START (for password

number “2”), press OK (for password number “3”).

7.5.6 Stand-by modus

When the mower is without task over 30 minutes, and when there is no new mowing task

within 30 minutes, the mower goes into stand-by modus.

The GPS- and Status lights will go off (no indication), only when activating the mower

manually or with use of the APP, both lights will be re-activated.

POWXG6310 EN

7.6 Smartphone application (APP)

7.6.1 Download the APP

Scan the QR, see fig. 9, with your mobile phone to download the application. Select the

appropriate channel for your mobile, Android or Apple.

You can also find the APP on Google Play or Apple App Store under the name: "Powerplus

mower POWXG6310".

The advantages of the APP are shown below:

1. The panel is limited to basic control, and the APP can set up the work plan

2. The APP can set the working mode

3. The APP can monitor the mower remotely and display the fault directly

4. The APP can upgrade online

7.6.2 Add your mower into the APP

Once APP is downloaded and you can add your robotic mower by following these steps:

1. Switch the mower on. The On/Off switch is located at the bottom side of the robotic

lawnmower. Enter into the step 2 when the mower has enough power for working.

2. Wait for the power LED turns on (solid green, not flashing).

3. Scan the unique QR or input the code of the mower to find it. See fig. 10 for your

mower’s individual QR and code.

4. Match the mower with your smartphone within 10 meters.

7.6.3 Connect the APP on two way

You have two options to connect to the robotic lawnmower.

1. Via Bluetooth

 Connect your mobile to the robotic lawnmower via Bluetooth. This is

within a radius of max. 10 meters from the robotic lawnmower.

2. Via Wi-Fi

 Connect both the robotic lawnmower and your mobile to your Wi-Fi

network. It is important that the Wi-Fi signal is also available in the garden

at the location of the robotic lawnmower.

 When connecting via Wi-Fi, a server connection is available so that you

can call up information from the robotic lawnmower with your mobile

regardless of location.

Note: It is necessary to connect the Bluetooth ion necessary before setting up

the Wi-Fi connection.

Note: When open the “Rainy days work”, the mower will still work when it

detects the rain..

Note: Users can choose two orientations to mow the working area. Press

“Parallel mode” and “General mode (random mode)” buttons to set. In the

“General mode”, the north （ N ） means that the mowing orientation is 0°，

the south （S）means that the mowing orientation is 180°，the east （E）

means that the mowing orientation is 90°， the Mower Setting Page Wi-Fi

Binding Page west （W）means that the mowing orientation is 270°. The

mowing orientation can be set at any direction.

POWXG6310 EN

Note: The mowing direction only can be set while the mower is charging in the

charging station.

Note: When the GPS signal turns red, wait for 10 minutes. When it turns green

it means it is in normal state. If the GPS signal doesn’t turn green, please

contact a specialist to check the mower.

7.7 Control panel information (Fig 7)

7.7.1 Light status

Light

1st function

2nd function

Status light

Shows the mower is on

Shows fault code in case of a problem

GPS light

Shows whether the

mower connects to the

satellite steadily

When entering the password: represents

the digit of the password

7.7.2 Buttons

Button

1st function

2nd function

HOME

Send the mower to the

charging station after

pressing HOME+OK

(within 5 seconds)

- When entering the password: number

one (1)

START

Start the robotic mower

after pressing

START+OK (within 5

seconds) when the

power light is on

- When entering the password: number

two (2)

Confirm the status

- When entering the password: number

three (3)

Note: The mower returns to the charging station automatically with a low

battery.

8 TROUBLE SHOOTING

8.1 Fault codes

The robotic mower displays a fault code when unexpected events occurs. You can check the

fault code to find out the problem. See the list of fault codes below.

8.1.1 Fault codes (when outside charging station)

Status light flashing

Machine status

2 times

The emergency stop button is triggered

3 times

Excessive inclination or overturning causes the mowing to end

6 times

The lift sensor is triggered causes the mowing to end

7 times

The mower is in trouble causes the mowing to end

POWXG6310 EN

8 times

Low battery causes the mowing to end

9 times

High temperature causes the mowing to end

10 times

Abnormal clogging of the mowing motor causes the mowing to

end

11 times

Alternative brake abnormally causes the mowing to end

13 times

Over-temperature of the mowing motor causes the mowing to

end

14 times

Rain caused the mower come back to charging station

15 times

Driving motor operates abnormally

16 times

Abnormal current of mowing motor

17 times

Left driving motor operates abnormally

18 times

Right driving motor operates abnormally

This light is on

The mower runs normally

The light is off

No power or in low voltage protection

8.1.2 Fault codes (when charging)

Status light flashing

Machine status

Continuous block flash

quickly (four times a

second)

The mower is charging

Continuous slow flash

(every two seconds)

The mower is completely charged

1 time

Over charging temperature protection

2 times

Abnormal charger protection, charging voltage is too high

3 times

Abnormal charger protection, charging current is too high

4 times

Abnormal battery protection, battery voltage is too low (no

charging below 10V)

5 times

BMS (Battery Management System) protection, no charging

allowed

The light is off

The mower does not turn on or is in low voltage protection state

(the voltage is lower than 16V, the mower should be restarted)

8.1.3 Clear the fault code

To clear the fault code follow these steps:

1. Make sure that all conditions for restarting the mower are met (for the mower itself

and in the mowing area).

2. Enter the Password.

3. Press START +OK at the same time to leave fault code.

4. Press START +OK within 5 seconds to restart the mower.

8.2 Mower does not work

Problem

Cause

Action

The mower stops during

mowing

Battery low

Re-charge the mower.

POWXG6310 EN

Buttons respond

abnormally

The password is wrong.

See the chapter of “password” .

The power of the mower

is cut off automatically

due to low battery

Battery low

Re-charge the mower.

8.3 Troubleshooting of the application

The mobile displays a fault code when unexpected events occurs. Solve the problem as

shown below.

Error

Icon

How to solve

Wire sensor power

inversion!

The perimeter wire is

set in the opposite

terminal of the

charging station.

Press the “Reset” button.

Reconnect the perimeter

wire correctly. See chapter

“Setting up the perimeter

wire” for details.

Reconfirm

boundary?

The perimeter wire is

set wrong which

cannot be detected

by the mower.

Press the “YES” button.

Reconnect the perimeter

wire correctly. See chapter

“Setting up the perimeter

wire” for details.

Unable to get out!

The mower is in

trouble to get through

the working area.

Press the “OK” button.

Check the working area if

the ground is flat. IF not, do

not allow the mower

mowing there again.

POWXG6310 EN

There are obstacles

in the path!

The mower is in

trouble with some

obstacles in the path.

Press the “OK” button.

Move the obstacles from

the path.

Out!

The mower is not in

the boundaries.

Press the “OK” button.

Stop the mower and move

the mower into the working

area , restart it.

Walk time out!

The mower impacting

the obstacles causes

the walk time out

during the recharging

procedure.

Press the “OK” button.

Move the obstacles from

the recharging path.

Abnormal power

loss!

The battery of the

mower is losing

power.

Press the “OK” button.

Recharge the mower.

POWXG6310 EN

Mower was turned

over!

Stop the mower and rotate

the mower, restart it.

Fault of left-wheel

motor!

Stop the mower and

contact a specialist to

repair it.

Fault of right-wheel

motor!

Stop the mower and

contact a specialist to

repair it.

Wired sensor signal

loss!

Stop the mower and

contact a specialist to

repair it.

Emergency stop!

Press the “OK” button.

Restart the mower.

POWXG6310 EN

9 MAINTENANCE

Note: To ensure long and reliable service, carry out the following

maintenance regularly.

WARNING: Be aware of the danger of moving hazardous parts.

WARNING: Do not touch moving hazardous parts. Make sure the power

switch is set to OFF and make sure that all moving parts have come to a

stop before doing any maintenance on the mower.

9.1 General maintenance plan

Item

Action

Once a

week

Once a year / every 500

hours

Blades

Inspect

Blade plate

Inspect

STOP button

Inspect

Chassis accessories

Clear

Inspect

X (twice a year)

Charging station

Clear

Inspect

Charging station base

Inspect / Adjust

Driving wheel

Clear

Inspect

X (twice a year)

Omnidirectional wheels

Clear

Inspect

X (twice a year)

9.2 Cleaning the mower

ATTENTION! The power switch must be set to OFF before cleaning the

mower!

Wear thick gloves before turning the mower and while cleaning. The blades are sharp!

Do not use high pressure cleaners!

1. Set the On / Off switch of the mower to OFF.

2. Clear the blades and the blade plate with a brush. Remove all dirt and check

whether the blades can move free. Check this every two weeks.

3. Clean the surface of the mower with a piece of cloth. Don´t use any dissolvent.

POWXG6310 EN

9.3 Blade replacement (Fig 8)

ATTENTION! When fitting new blades, make sure you replace ALL the

blades. Always use new screws when fitting blades. This is important to

ensure blade retention. Failure to use screws could cause serious injury.

ATTENTION! Wear gloves when handling the blade. Only use original

replacement parts specified for this mower. Powerplus spare blades and

screws item reference number: POWACG9101.

It’s recommended that replace the blades within 2-3 months.

There are 3 blades on the robotic lawnmower, which are screwed into the blade disc. All 3

blades and screws must be replaced at the same time to obtain a balanced cutting system.

1. Set the on/off switch of the mower to "OFF".

2. Turn the robotic lawnmower upside down. Place the robotic lawnmower on a soft

and clean surface to avoid scratching the body and the cover.

3. Rotate the blade plate so that its holes align with the hole in the machine frame and

insert screw driver to block the blade plate.

4. Remove the 3 screws with a screwdriver.

5. Remove each blade and screw.

6. Fasten new blades and screws.

7. Check that the blades can pivot freely.

9.4 Storage

Keep your mower and the charging station in a warm and dry place during winter.

1. Fully charge the battery.

2. Set the On / Off switch of the mower to OFF.

3. Clean the mower.

4. Disconnect the charging station from the power supply.

5. Disconnect the wire from the charging station.

6. Lift the charging station from the ground and clean it.

7. Store the mower and the charging station in a dry place.

10 TECHNICAL DATA

Type

POWXG6310

Mains voltage (charger unit)

220-240 V / 50 Hz

No load speed

3200 min

-1

Running time

140 min

Battery type

Li-Ion

Battery voltage

18 V

Battery capacity

5.0 Ah

Charging time (empty battery)

180 min

Motor type

Brushless

Max. area

1000 m2

Cutting width

18 cm

Max slope

30% （17°)

Boundary wire(max.)

150 m

Charging current

2 A

Weight with 5.0 Ah battery

7.9 kg

POWXG6310 EN

11 NOISE

The declared vibration total value has been measured in accordance with a standard test

method and may be used for comparing one tool with another.

The declared vibration total value may also be used in a preliminary assessment of exposure.

The vibration emission during actual use of power tool can differ from the

declared total value depending on the ways in which the tool is used.

The safety measures to protect the operator are identified based on an

estimation of exposure in the actual conditions of use.

A-weighted emission sound pressure level at the operator position as determined according to

the relevant standard, where this level does not exceed 70 dB(A):

Acoustic pressure level LpA

48 dB(A)

Uncertainties surrounding the determined

noise emission values K

3 dB(A)

Acoustic power level LwA

59 dB(A)

If there is any abnormal vibration please inspect your mower for any abnormal blockage. If

necessary clean the mower and/or replace the blades.

Page is loading ...

Powerplus POWXG6310 Owner's manual

Powerplus POWXG6310 Owner's manual

Powerplus POWXG6310 Owner's manual

Related papers

Other documents