Pyle PDWM1950 is a compact UHF wireless microphone system with 16 channels, a 96dB signal-to-noise ratio, and a frequency response of 30Hz to 20kHz. It has a 500kHz channel interval, a 600 Ohm output impedance, and a power consumption of less than 85mA. The handheld transmitter has a power output of 10dBm and operates on 3V (normal battery) or 3.7V (lithium battery). The bodypack transmitter also has a power output of 10dBm and operates on 3V.
Pyle PDWM1950 is a compact UHF wireless microphone system with 16 channels, a 96dB signal-to-noise ratio, and a frequency response of 30Hz to 20kHz. It has a 500kHz channel interval, a 600 Ohm output impedance, and a power consumption of less than 85mA. The handheld transmitter has a power output of 10dBm and operates on 3V (normal battery) or 3.7V (lithium battery). The bodypack transmitter also has a power output of 10dBm and operates on 3V.
Compact UHF Wireless Microphone System
USB Powered Desktop Mic Receiver System
with Adjustable Volume Control
PDWM1950 PDWM1958B PDWM2850
PDWM2880B PDWM1980
PDWM1988B PDWM2950
PDWM2958B
www.PyleUSA.com
www.PyleUSA.com
1
• To set up the system and to avoid interference, each unit may have many
presented channels.
• When using numbers of receiversltransmitters together, each unit should use
dierent channels.
Tips
1. Transmitter and antenna should keep in a barrier-free linear relative position.
2. Do not place receiver close to metal surface object or digital equipment.
3. Try to keep receiver 1.5m above the floor and 1m away from the wall.
Contents
System Component
Receiver
Body Pack Transmitter
Body Pack Transmitter Connection
Charging the Microphone
Conguration of Multiple Systems
Troubleshooting
Specication
System Component
The contents above are for the whole system, the actual component may dier
1
2-3
4-6
7
8
8
9
11
8 8 8 8
12
1450 0
11
13
1. Wireless receiver
2. Adapter (optional)
3. Adapter (optional)
4. Cable (optional)
5. Charging cab|e(optional)
6. AA batteries (optional)
7. 14500 lithium battery (optional)
8. User manual (Optional)
9. Handheld transmitter (optional)
10. Body pack transmitter (optional)
11. Lavalier microphone (optional)
12. Headset mic (optional)
13. 6.35" signal output cable
www.PyleUSA.com
2
www.PyleUSA.com
3
1. Power signal lamp
2. LED display
3. Battery Cover
4. Frequency-change button
5. Power switch
Receiver
The images above are indicative only, the actual product may dier
VOL-A
POWER
VOL-A
POWER
AF RF
VOL-A
AF AF
POWER
RF RF
VOL-B
VOL-A VOL-B
POWER
ANT- A
ANT- B
DC 5V IN
A UD IO O U T
6 6
7
7
12
BAL ANCED -B
ANT -A ANT -B
BAL ANCED -A
D C 5 V O U T
D C 5 V I N
A UD IO O U T
12
11
10
9
8
8 10
BAL ANCED
ANT -A
ANT -B
D C 5 V I N
D C 5 V O U T
A UD IO O U T
11
10
9
8
2
5
5 5
8 8 8 8
8 8 8 8
5 5
5
1. Power Switch
2. VOL. A
3. VOL. B
4. RF Signal Lamp
5. AF Signal Lamp
6. Power Signal Lamp
7. LCD Display
8. 1/4 Audio Output Socket
9. XLR Audio Output Socket
10. Power Input Socket
11. Charging Socket
12. ANT-A
www.PyleUSA.com
4
www.PyleUSA.com
5
Matching Receiver and Transmitter (Only apply to some models)
1. Make sure the receiver is powered OFF.
2. On transmitter side, press and hold the frequency- change button, then press
and hold the power button till the display is flashing.
3. Turn ON the receiver and then you will see the RF light is flashing.
4. Attention: For the receiver that has LED display, turn ON the receiver and
wait for 3-5 seconds
5. Get back to the transmitter side and re-press the frequency-change button.
6. Matching is successful if the RF light is ON or the LED display shows frequency,
otherwise, re-do step 1 to step 5.
Body Pack Transmitter (Only apply to some models)
Functions
1. Clip microphone socket
2. LED Iight
3. Antenna
4. LED display
5. Frequency-change button
6. Power switch
1
1
1
1
1
Frequency-change button
1
Matching Receiver and Transmitter (Only apply to some models)
1. Make sure the receiver is powered OFF.
2. On transmitter side, press and hold the frequency- change button, then press
and hold the power button till the display is flashing.
3. Turn ON the receiver and then you will see the RF light is flashing.
4. Attention: For the receiver that has LED display, turn ON the receiver and
wait for 3-5 seconds
5. Get back to the transmitter side and re-press the frequency-change button.
6. Matching is successful if the RF light is ON or the LED display shows frequency,
otherwise, re-do step 1 to step 5.
www.PyleUSA.com
6
www.PyleUSA.com
7
BODYPACK TRANSMITTER CONNECTION
1. Lavalier Microphone Connection:
Connect the connector of supplied lavalier microphone to the connecting jack
of transmitter (Shown as below). Set the transmitter work state in wireless
lavalier system.
2. Headset Microphone Connection:
Connect the connectorof supplied headset microphone to the connecting
jack of transmitter (Shown as below). Set the transmitter work state in wireless
headset system.
8 8 8 8
VOL-A
AF AF
POWER
RF RF
VOL-B
Wa it for 4 5 s ec onds
VOL-A
AF AF
POWER
RF RF
VOL-B
POWE R OFF
8 8 8 8
Flashing
Frequence
change button
a
b
c
8 8 8 8
O K
VOL-A
AF AF
POWER
RF RF
VOL-B
P O W E R ON
Flashing
a
b
1
2 3
4
Press and hold
Press and hold
5
6
A B
A B
www.PyleUSA.com
8
www.PyleUSA.com
9
TROUBLESHOOTINGCharging the microphone (Only apply to some models)
CAUTION: For charging microphone, MUST NOT use AA battery to power the
microphone. MUST use 14500 lithium battery.
Conguration of Multiple Systems
1. Transmitters match corresponding receivers to prevent frequency interference
(See "Matching receiver and transmitter" for reference)
2. Using dierent frequencies among transmitters
(The dierence should be 3-4MHz for each transmitters)
BALANCED-B
ANT- A ANT- B
BALANCED-A
DC 5 V O UT
DC 5 V I N
A UD IO O U T
VOL-A
AF AF
POWER
RF RF
VOL-B
VOL-A VOL-B
POWER
Charging socket
Problem Status Solution
No sound
or sound is weak
Transmitter display
or light is o
1. Turn on transmitter
2. Make sure battery is
installed right
3. Replace batteries
Receiver display
or light is o
Make sure adapter is pluged
into receiver DC socket, and
the adapter is power supplied
Receiver display or light
indicate RF signal
1. Turn up receiver volume
2. Check the cable connection
of receiver
Receiver display or light
indicate no RF signal;
Transmitter and receiver
power light is on
1. Remove receiver away from
metal objects
2. Check if barrier is between
receiver and transmitter
3. See “Matching receiver and
transmitter”
Distortion or
unwanted noise
bursts
Receiver display or light
indicate RF signal
1. Remove interference
sources nearby
2. Change receiver and
transmitter working
frequency
3. Replace transmitter
batteries
4. If using many sets together,
increase working frequency
interval of systems
5. Maximize the volume
button
Failed to turn ON
transmitter
Press power button,
transmitter not working,
or shut down after a
second
1. Replace batteries
2. Re-press power button
after few seconds
www.PyleUSA.com
10
www.PyleUSA.com
11
SPECIFICATION
Some specication may not apply to some models.
RECEIVER
Channels ----------------------------------------------- 16 Channels
SNR --------------------------------------------------------- 96db
Sensitivity -------------------------------------------------- 96dbm
Frequency Response ---------------------------------------30~20kHz
Channel Interval ---------------------------------------------500kHz
Output Impedance ----------------------------------------- 600 Ohm
Power Supply --------------------------------------------------- 5V
Power Consumption ------------------------------------------<85Ma
LED Display
HANDHELD TRANSMITTER
Power Output ----------------------------------------------- 10dbm
Frequency Response ------------------------------------30kHz~20kHz
Power Supply ------------------------------------- 3v (Normal battery)
Power Supply ----------------------------------- 3.7V (Lithium battery)
BODYPACK TRANSMITTER
Power Output ----------------------------------------------- 10dbm
Frequency Response ------------------------------------30kHz~20kHz
Power Supply --------------------------------------------------- 3v
DESKTOP WIRELESS MICROPHONE SYSTEM
PDWM1950 PDWM1958B PDWM2850
PDWM2880B PDWM1980
PDWM1988B PDWM2950
PDWM2958B
-
1
-
2
-
3
-
4
-
5
-
6
-
7
Pyle PDWM1950 is a compact UHF wireless microphone system with 16 channels, a 96dB signal-to-noise ratio, and a frequency response of 30Hz to 20kHz. It has a 500kHz channel interval, a 600 Ohm output impedance, and a power consumption of less than 85mA. The handheld transmitter has a power output of 10dBm and operates on 3V (normal battery) or 3.7V (lithium battery). The bodypack transmitter also has a power output of 10dBm and operates on 3V.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
