Bosch GHP 6-14 Operating instructions

Page is loading ...

English | 9

Bosch Power Tools F 016 L72 355 | (16.8.12)

Transport

Um den Hochdruckreiniger zu bewegen, fassen Sie diesen am

oberen Griff und rollen ihn auf den Rädern zum gewünschten

Ort.

Um den Hochdruckreiniger über Treppen oder Hindernisse zu

transportieren, fassen Sie diesen am oberen Griff und tragen

Sie ihn.

Nach Gebrauch/Aufbewahrung

Das Äußere des Hochdruckreinigers mit Hilfe einer weichen

Bürste und einem Lappen reinigen. Wasser, Lösemittel und

Poliermittel dürfen nicht verwendet werden. Alle Verschmut-

zungen entfernen, insbesondere die Lüftungsschlitze des Mo-

tors reinigen.

Lagerung nach Saisonende: Entleeren Sie alles Wasser aus

der Pumpe, indem Sie den Motor einige Sekunden laufen las-

sen und den Abzug betätigen.

Keine anderen Gegenstände auf das Gerät stellen.

Stellen Sie sicher, dass die Kabel während der Lagerung nicht

eingeklemmt sind. Knicken Sie den Hochdruckschlauch nicht

ab.

Kundendienst und Kundenberatung

www.bosch-garden.com

Deutschland

Robert Bosch GmbH

Servicezentrum Elektrowerkzeuge

Zur Luhne 2

37589 Kalefeld – Willershausen

Tel. Kundendienst: +49 (1805) 70 74 10*

Fax: +49 (1805) 70 74 11*

(*Festnetzpreis 14 ct/min, höchstens 42 ct/min aus Mobil-

funknetzen)

E-Mail: Servicezentrum.Elektrowerkzeuge@de.bosch.com

Tel. Kundenberatung: +49 (1803) 33 57 99

(Festnetzpreis 9 ct/min, höchstens 42 ct/min aus Mobilfunk-

netzen)

Fax: +49 (711) 7 58 19 30

E-Mail: kundenberatung.e[email protected]om

Österreich

Tel.: +43 (01) 7 97 22 20 10

Fax: +43 (01) 7 97 22 20 11

E-Mail: service.elektrowe[email protected]ch.com

Schweiz

Tel.: +41 (044) 8 47 15 11

Fax: +41 (044) 8 47 15 51

Luxemburg

Tel.: +32 2 588 0589

Fax: +32 2 588 0595

E-Mail: [email protected]om

Umweltschutz

Umweltbelastende Chemikalien dürfen nicht in den Boden,

ins Grundwasser, in Teiche, Flüsse etc. gelangen.

Bei der Verwendung von Reinigungsmitteln die Angaben auf

der Verpackung und die vorgeschriebene Konzentration ge-

nau einhalten.

Bei der Reinigung von Motorfahrzeugen die örtlichen Vor-

schriften beachten: Es muss verhindert werden, dass abge-

sprühtes Öl ins Grundwasser gelangt.

Entsorgung

Hochdruckreiniger, Zubehör und Verpackungen sollen einer

umweltgerechten Wiederverwertung zugeführt werden.

Werfen Sie Hochdruckreiniger nicht in den Hausmüll!

Nur für EU-Länder:

Gemäß der Europäischen Richtlinie

2002/96/EG über Elektro- und Elektronik-

Altgeräte und ihrer Umsetzung in nationales

Recht müssen nicht mehr gebrauchsfähige

Elektro- und Elektronikgeräte getrennt ge-

sammelt und einer umweltgerechten Wie-

derverwertung zugeführt werden.

Änderungen vorbehalten.

English

Safety Notes

Explanation of symbols

General hazard safety alert.

Never direct the water jet at people, ani-

mals, the unit or electric components.

Warning: High pressure jets can be dan-

gerous if subject to misuse.

According to the applicable regulations, the

appliance must never be used on the drinking

water network without a system separator.

Use a separator as per IEC 61770 Type BA.

Water flowing though a system separator is

considered not drinkable.

For self priming use special suction kit 3 m

long (F 016 800 335).

Safety Notes for pressure washer

Read all safety warnings and all instructions.

Failure to follow the warnings and instructions

may result in electric shock, fire and/or serious in-

jury.

The warning and information signs attached to the unit

provide important information for safe operation.

Apart from the information in the operating instructions

comply with the general safety regulations and regula-

tions for the prevention of accidents.

OBJ_BUCH-1762-001.book Page 9 Thursday, August 16, 2012 10:03 AM

10 | English

F 016 L72 355 | (16.8.12) Bosch Power Tools

Power supply

f The voltage indicated on the rating plate must correspond

to the voltage of the power source.

f We recommend that this equipment is only connected into

a socket which is protected by a circuit-breaker that would

be actuated by a 30 mA residual current.

f This is a class I unit and may only be connected to properly

earthed power sources.

f Remove the plug from socket whenever the machine is left

unattended for any period.

f The electric supply installation should comply with

IEC 60364-1.

f If the supply cord is damaged, it must be replaced by the

manufacturer, its service agent or similarly qualified per-

sons in order to avoid a hazard.

f Never touch the mains plug with wet hands.

f Do not pull plug while operating the device.

f Do not run over, crush or pull the power supply cable or ex-

tension lead, otherwise it may be damaged. Protect the ca-

ble from heat, oil and sharp edges.

f Do not use the appliance, if the power supply cable or im-

portant parts, e. g. high-pressure hose, trigger gun or safe-

ty devices are damaged.

f Warning: Inadequate extension cords can be dangerous.

f If an extension cord is used, the plug and socket must be of

watertight construction. The extension cord must have a

cross section in accordance with the operating instruc-

tions and be protected against splashed water. The con-

nection must not be in water.

f When replacing plugs on the power supply cable or exten-

sion lead the spray water guard and mechanical stability

must remain intact.

Water connection

f Comply with the regulations of your water supply compa-

ny.

f All connecting hoses must have properly sealed joints.

f The appliance should never be used on the drinking water

supply without a back flow valve. Water which has passed

the back flow valve is regarded as undrinkable.

f The high-pressure hose must not be damaged (danger of

bursting). A damaged high-pressure hose must be re-

placed immediately. Only use hoses and connections rec-

ommended by the manufacturer.

f High-pressure hoses, fittings and couplings are important

for the safety of the appliance. Use only hoses, fittings and

couplings recommended by the manufacturer.

f Only clean or filtered water should be used for intake.

Application

f Before use, check that the unit and operating equipment

are in perfect condition and are safe to operate. Do not use

the unit if it is not in perfect condition.

f Do not direct the jet against yourself or others in order to

clean clothes or footwear.

f Never draw in solvent-containing liquids, undiluted acids,

acetone or solvents! This includes petrol, paint thinners,

heating oil. The sprayed vapour is highly flammable, explo-

sive and toxic.

f The appropriate safety regulations must be observed

when using the unit in dangerous areas (e.g. petrol sta-

tions). It is forbidden to operate the unit in potentially ex-

plosive locations.

f The unit must be placed on a solid base.

f Only use detergents recommended by the manufacturer

and comply with the application, disposal and warning in-

structions of the detergent manufacturers.

f All current-conducting components in the working area

must be protected against splashed water.

f The gun trigger must not be jammed in position “ON” dur-

ing operation.

f Wear suitable protective clothing to protect against

splashing from some parts. Do not use the appliance within

the range of persons unless they also wear protective

clothing.

f High pressure may cause objects to rebound. If necessary

wear suitable personnel protective equipment such as

safety goggles.

f Vehicle tyres/tyre valves may only be cleaned from a mini-

mum distance of 30 cm, otherwise the vehicle tyre/tyre

valve could be damaged by the high-pressure jet. The first

indication of this is a discoloration of the tyre. Damaged

vehicle tyres/tyre valves can be extremely dangerous.

f Materials containing asbestos and other materials which

contain substances which are hazardous to your health

must not be sprayed.

f Detergents must not be used undiluted. The products are

safe to use as they contain no acids, alkalis or substances

which are detrimental to the environment. We recommend

that the detergents are kept out of the reach of children. If

detergent comes into contact with the eyes, wash immedi-

ately with plenty of water and if swallowed contact a doctor

immediately.

f Never use the pressure washer without the filter, a

dirty filter or a damaged filter. Using the pressure wash-

er without/damaged filter may invalidate the warranty.

f If necessary wear personal protective equipment (PPE)

e. g. safety goggles, breathing protection etc to protect

against water, particles and/or aerosols sprayed back from

parts.

f Metal parts may become hot after prolonged usage, if nec-

essary wear protective gloves.

f Avoid high pressure washing in bad weather conditions es-

pecially when there is a risk of lightening.

Operation

f The operator must use the unit in accordance with the reg-

ulations. He/she must take local conditions into account

and be aware of other people, especially children, when

operating the unit.

OBJ_BUCH-1762-001.book Page 10 Thursday, August 16, 2012 10:03 AM

English | 11

Bosch Power Tools F 016 L72 355 | (16.8.12)

f The unit may only be used by authorised persons who have

received training or have demonstrated their ability to op-

erate the unit. The unit must not be operated by children or

juveniles (danger of accidents due to incorrect use of the

unit). Children should be supervised to ensure that they do

not play with the appliance.

f The unit is not intended for use by persons (including chil-

dren) with reduced physical, sensory or mental capabili-

ties, or lack of experience and knowledge, unless they

have been given supervision or instruction concerning use

of the unit by a person responsible for their safety.

f The unit must never be left unsupervised while the unit is

switched on.

f The water jet from the high-pressure nozzle produces a re-

coil on the gun. You should therefore hold the gun and

spray lance firmly with both hands.

Transport

f Switch off the motor and secure the unit before transport-

ing.

Maintenance

f Switch off the unit prior to all cleaning and maintenance

work and before replacing components. Pull out the mains

plug if the unit is mains-operated.

f Repairs may only be carried out by authorised Bosch Serv-

ice Centres.

Accessories and spare parts

f Only use accessories and spare parts which have been ap-

proved by Bosch. Original accessories and spare parts

guarantee that the unit can be operated safely and without

any breakdowns.

Symbols

The following symbols are important for reading and under-

standing the operating instructions. Please take note of the

symbols and their meaning. The correct interpretation of the

symbols will help you to use the machine in a better and safer

manner.

Intended Use

The product is intended for cleaning areas and objects out-

side the house, tools, vehicles and boats, if the appropriate

accessories such as cleaning agents approved by Bosch are

used.

Intended use is related to operation within 0°C and 40°C am-

bient temperature.

Technical Data

Symbol Meaning

Movement direction

Weight

On

Off

Lo Low pressure

Hi High pressure

Accessories

Pressure washer GHP 5-14 GHP 6-14

Article number

3 600 J10 1.. 3 600 J10 2..

Rated power

kW 2.4 2.6

Supply Temperature max.

°C 50 50

Supply rate min.

l/min 8.3 10.5

Rated pressure

MPa 14 14

Max. operating pressure

MPa 15 15

Flow rate

l/min 8.3 10.5

Maximum input pressure

MPa 1 1

Repulsive force at the gun to the maximum pressure

N22.9832.24

Motor Insulation

Class F Class F

Motor Protection

IPX5 IPX5

Detergent tank

– z

Autostop function

z z

Net impedance

Ù Ù

Weight according to EPTA-Procedure 01/2003

kg 23.4 25.6

Protection class

/I /I

Serial number

See serial number (rating plate) on pressure washer.

Starting cycles generate brief voltage drops. Interference with other equipment/machines may occur in case of unfavourable mains system conditions.

Malfunctions are not to be expected for system impedances below 0,153 ohm.

OBJ_BUCH-1762-001.book Page 11 Thursday, August 16, 2012 10:03 AM

12 | English

F 016 L72 355 | (16.8.12) Bosch Power Tools

Noise/Vibration Information

Declaration of Conformity

Equipment category: 27

Technical file (2006/42/EC, 2000/14/EC) at:

Bosch Lawn and Garden Ltd., PT-LG/ENS,

Stowmarket, Suffolk IP14 1EY, England

Robert Bosch GmbH, Power Tools Division

D-70745 Leinfelden-Echterdingen

29.06.2012

Mounting and Operation

Starting

For Your Safety

Warning! Switch off, remove plug from mains be-

fore adjusting, cleaning or if cable is cut, dam-

aged or entangled.

Your pressure washer requires an earth connection. The op-

erating voltage is 230 V AC, 50 Hz (for non-EU countries

220 V, 240 V as applicable). Only use approved extension ca-

bles. Contact your Bosch Service Centre for details.

If you want to use an extension cable when operating your

high pressure washer, only the following cable dimensions

should be used:

– 2.5 mm

2

– max length 20 m

– 4.0 mm

2

– max length 50 m

Note: If an extension cable is used it must be earthed and con-

nected through the plug to the earth cable of your supply net-

work in accordance with prescribed safety regulations.

If in doubt contact a qualified electrician or the nearest Bosch

Service Centre.

WARNING! Inadequate extension cables can be

dangerous. Extension cable, plug and socket

must be of watertight construction and intended

for outdoor use.

Cable connections should be kept dry and off the ground.

For increased electrical safety to use a Residual Current De-

vice (RCD) with a tripping current of not more than 30 mA. Al-

ways check your RCD every time you use it.

If the supply cord is damaged, it must be replaced by a Bosch

Service Centre.

Products sold in GB only: Your product is fitted with an

BS 1363/A approved electric plug with internal fuse (ASTA

approved to BS 1362).

Measured sound values determined according to 2000/14/EC (1.60 m height, 1 m dis-

tance away).

3 600 ... J 10 1.. J10 2..

Typically the A-weighted noise levels of the product are:

Sound pressure level

Sound power level

Uncertainty K

Wear hearing protection!

dB(A)

dB

84.5

92

=3

82.5

90

=3

Vibration total values (triax vector sum) determined according to EN 60335:

Vibration emission value a

h

Uncertainty K

m/s

2

m/s

2

=4.91

=1.5

=4.91

=1.5

3 600 ... J 10 1.. J10 2..

We declare under our sole responsibility that the product described under “Technical data”

is in conformity with the following standards or standardization documents: EN 60335 ac-

cording to the provisions of the directives 2011/65/EU, 2004/108/EG, 2006/42/EG,

2000/14/EG.

2000/14/EC: Guaranteed sound power level

Conformity assessment procedure according to Annex V.

dB(A) 92 90

Dr. Egbert Schneider

Senior Vice President

Engineering

Helmut Heinzelmann

Head of Product Certification

PT/ETM9

Action Figure

Delivery Scope 1

Handle Assembly 2

Filling up detergent tank 3

Water connection 4

Cleaning the Filter 5

Connecting high pressure water supply hose/

nozzle 6

Adjust water pressure 7

Adjust water jet 8

Switching on and off 9

Clean nozzle 10

OBJ_BUCH-1762-001.book Page 12 Thursday, August 16, 2012 10:03 AM

English | 13

Bosch Power Tools F 016 L72 355 | (16.8.12)

If the plug is not suitable for your socket outlets, it should be

cut off and an appropriate plug fitted in its place by an author-

ised customer service agent. The replacement plug should

have the same fuse rating as the original plug.

The severed plug must be disposed of to avoid a possible

shock hazard and should never be inserted into a mains sock-

et elsewhere.

For products not sold in GB:

WARNING: For your safety, it is required that the plug at-

tached to the machine is connected with the extension cord.

The coupling of the extension cord must be protected against

splash water, be made of rubber or coated with rubber. The

extension cord must be used with a cable strain relief.

Drawing in water from open reservoirs

– Screw the suction hose with filter (special suction kit part

no. F 016 800 335) to the water connection.

– Switch on the appliance in low pressure mode.

– Let the appliance run for appx. 10 seconds, then switch

off. Repeat the procedure a couple of times until water ex-

iting is smooth and bubble free.

To prevent damage to the appliance, do not allow it to operate

dry.

Operation

Starting

Attach water supply hose (not supplied) to the mains water

supply and machine.

Connect the product to the mains supply ensuring that the

mains switch is in the off position.

Open water tap.

Press the safety lock to release the trigger. Fully press the

trigger until there is a constant flow of water to clear the air

from the machine and water supply hose. Release trigger.

Point the power gun downwards. Press the trigger safety lock

to release the trigger. Fully press the trigger.

Operate on/off switch.

Autostop function

The machine is designed to switch off the motor when the trig-

ger is released on the gun.

Working Advice

General

Ensure that the pressure washer is on level ground.

Do not overreach with the high pressure hose or move the

pressure washer by pulling the hose, this could cause the ma-

chine to become unstable and fall over.

Do not kink or drive a motor vehicle over the high pressure

hose. Do not expose the high pressure hose to sharp edges or

corners.

Never use the roto nozzle to clean motor vehicles.

Do not tamper with or adjust the safety valve setting.

Working advice for cleaning with detergents

f Only use cleaning agents suitable specifically for high

pressure washers.

We recommend that you use detergent sparingly for the sake

of the environment. Observe the recommended dilution on

the detergent label.

By offering you an individualised range of cleaning and pre-

serving agents, Bosch guarantees troublefree operation of

the unit.

Recommended cleaning method

Step 1: Loosening dirt

Spray on detergent sparingly and allow to react for a short

time.

Step 2: Removing dirt

Spray off the loosened dirt with the high-pressure spray.

Note: When cleaning a vertical surface spray off dirt/deter-

gent from the bottom and work in an upwards direction. Rinse

from the top and work downwards.

Troubleshooting

Problem Possible Cause Corrective Action

Motor refuses to start Plug not connected Connect plug

Mains socket faulty Use another socket

Fuse faulty/blown Replace fuse

Extension cable damaged Try without extension cable

Motor protector has activated Allow to cool for 15 minutes

Frozen Wait for pump/water supply hose/acces-

sory to thaw

Motor stops Fuse faulty/blown Replace fuse

Wrong mains voltage Check that mains voltage corresponds to

specifications on the model tag

Motor protector has activated Allow to cool for 15 minutes

Fuses blow Fuses incorrectly rated Change to a mains supply higher than the

pressure washer amp consumption

OBJ_BUCH-1762-001.book Page 13 Thursday, August 16, 2012 10:03 AM

14 | English

F 016 L72 355 | (16.8.12) Bosch Power Tools

Maintenance and Service

Maintenance

f Stop, remove plug from the power supply and discon-

nect from water supply.

Note: To ensure long and reliable service, carry out the follow-

ing maintenance regularly.

Regularly check for obvious defects such as loose fixings, and

worn or damaged components.

Check that covers and guards are undamaged and correctly

fitted. Carry out necessary maintenance or repairs before us-

ing.

If the machine should happen to fail despite the care taken in

manufacture and testing, repair should be carried out by an

authorised customer service agent for Bosch garden prod-

ucts.

In all correspondence and spare parts orders, please always

include the 10-digit article number given on the type plate of

the machine.

Transport

To move the pressure washer use the top handle and roll the

pressure washer on the wheels.

To transport the pressure washer up or down steps or over

obstacles, it must be lifted by the top handle.

Motor starts but no pressure Nozzle partly blocked Clean nozzle

Motor “sounds” but fails to start Insufficient power supply Check that the voltage of the mains pow-

er supply line is the same as that on the

plate

Voltage loss due to use of extension cable Check characteristics of extension cable

Appliance not used for a long period of

time

Contact your Bosch Service Centre

Problems with TSS (Total Stop System)

device

Contact your Bosch Service Centre

Pressure pulsating Air in the inlet water supply hose/pump Allow pressure washer to run with open

spray handle and nozzle at low pressure

until regular working pressure is obtained

Inadequate water supply Check that the water supply corresponds

to specifications. The minimum specifica-

tion for the water supply hose is 1/2" or

13 mm diameter

Water strainer blocked Clean water strainer

Water supply hoses squeezed Straighten out kinked water supply hoses

High pressure hose too long Remove high pressure extension hose.

Retry (extension hose max. 7 m)

Pressure too low, but steady

Note: Several types of accessory will nor-

mally deliver a lower pressure

Nozzle worn Change the nozzle

Start/stop valve worn Activate trigger five times in quick suc-

cession

Motor starts up but with restricted or no

working pressure

No water supply Connect water supply

Water strainer clogged up Clean the water strainer

Nozzle clogged up Clean nozzle

The pressure washer starts irregularly by

itself

Pump/power gun leaky Contact your Bosch Service Centre

Water leaks from machine Leaking pump A slight water leak is permissible; in case

of excessive leak, contact Service centre.

No detergent taken in Adjustable nozzle on high pressure set-

ting

Set nozzle on “Lo” setting

Detergent too dense Dilute with water

High pressure hose extension being used Fit original hose

Deposits or restriction in detergent cir-

cuit

Flush with clean water and eliminate any

restrictions. If the problem persists, con-

tact your Bosch Service Centre.

Problem Possible Cause Corrective Action

OBJ_BUCH-1762-001.book Page 14 Thursday, August 16, 2012 10:03 AM

English | 15

Bosch Power Tools F 016 L72 355 | (16.8.12)

After use/Storage

Clean the exterior of the machine thoroughly using a soft

brush or cloth. Do not use water, solvents or polishes. Re-

move all debris, especially from the ventilation slots.

End of season storage: Drain water out of pump running mo-

tor for a few seconds. Pull trigger to release all water.

Do not place other objects on top of the machine.

Ensure cables are not trapped when storing. Do not kink high

pressure hose.

After-sales Service and Customer Assistance

www.bosch-garden.com

Great Britain

Robert Bosch Ltd. (B.S.C.)

P.O. Box 98

Broadwater Park

North Orbital Road

Denham

Uxbridge

UB 9 5HJ

Tel. Service: +44 (0844) 736 0109

Fax: +44 (0844) 736 0146

E-Mail: [email protected]

Ireland

Origo Ltd.

Unit 23 Magna Drive

Magna Business Park

City West

Dublin 24

Tel. Service: +353 (01) 4 66 67 00

Fax: +353 (01) 4 66 68 88

Australia, New Zealand and Pacific Islands

Robert Bosch Australia Pty. Ltd.

Power Tools

Locked Bag 66

Clayton South VIC 3169

Customer Contact Center

Inside Australia:

Phone: +61 (01300) 307 044

Fax: +61 (01300) 307 045

Inside New Zealand:

Phone: +64 (0800) 543 353

Fax: +64 (0800) 428 570

Outside AU and NZ:

Phone: +61 (03) 9541 5555

www.bosch.com.au

Republic of South Africa

Customer service

Hotline: +27 (011) 6 51 96 00

Gauteng – BSC Service Centre

35 Roper Street, New Centre

Johannesburg

Tel.: +27 (011) 4 93 93 75

Fax: +27 (011) 4 93 01 26

E-Mail: [email protected]

KZN – BSC Service Centre

Unit E, Almar Centre

143 Crompton Street

Pinetown

Tel.: +27 (031) 7 01 21 20

Fax: +27 (031) 7 01 24 46

E-Mail: bsc.dur@za.bosch.com

Western Cape – BSC Service Centre

Democracy Way, Prosperity Park

Milnerton

Tel.: +27 (021) 5 51 25 77

Fax: +27 (021) 5 51 32 23

E-Mail: [email protected]

Bosch Headquarters

Midrand, Gauteng

Tel.: +27 (011) 6 51 96 00

Fax: +27 (011) 6 51 98 80

E-Mail: rbsa-hq.pt[email protected]

Environmental Protection

Chemicals dangerous to the environment must not be allowed

to enter the ground, ground water or ponds, streams, etc.

For the use of cleaning agents, observe the instructions on the

package and the prescribed concentration exactly.

For the cleaning of motor vehicles the local regulations should

be observed: Do not allow oil sprayed off to enter into the

ground water. Recycle raw materials instead of waste dispos-

al.

Disposal

The pressure washer, accessories and packaging should be

sorted for environmental-friendly recycling.

Do not dispose of pressure washers into household waste!

Only for EC countries:

According to the European directive

2002/96/EC for Waste Electrical and Elec-

tronic Equipment and its implementation

into national law, electrical and electronic

equipment that are no longer usable must

be collected separately and disposed of in

an environmentally correct manner.

Subject to change without notice.

OBJ_BUCH-1762-001.book Page 15 Thursday, August 16, 2012 10:03 AM

Page is loading ...

| 193

Bosch Power Tools F 016 L72 355 | (16.8.12)

1

25,6 kg

OBJ_BUCH-1762-001.book Page 193 Thursday, August 16, 2012 10:03 AM

F 016 L72 355 | (16.8.12) Bosch Power Tools

194 |

CHEM.

2

3

OBJ_BUCH-1762-001.book Page 194 Thursday, August 16, 2012 10:03 AM

| 195

Bosch Power Tools F 016 L72 355 | (16.8.12)

4

5

OBJ_BUCH-1762-001.book Page 195 Thursday, August 16, 2012 10:03 AM

F 016 L72 355 | (16.8.12) Bosch Power Tools

196 |

17 mm

6

7

OBJ_BUCH-1762-001.book Page 196 Thursday, August 16, 2012 10:03 AM

| 197

Bosch Power Tools F 016 L72 355 | (16.8.12)

Hi

Lo

9

8

OBJ_BUCH-1762-001.book Page 197 Thursday, August 16, 2012 10:03 AM

F 016 L72 355 | (16.8.12) Bosch Power Tools

198 |

10

OBJ_BUCH-1762-001.book Page 198 Thursday, August 16, 2012 10:03 AM

Bosch GHP 6-14 Operating instructions

Bosch GHP 6-14 Operating instructions

in other languages

Related papers

Other documents