Rothenberger 1000001652 User manual

Category
Angle grinders
Type
User manual
RO AG8000
RO BC14/36, RO BP18/2-18/4
www.rothenberger.com
DE Bedienungsanleitung
EN Instructions for use
FR Instruction d’utilisation
ES Instrucciones de uso
IT Istruzioni d’uso
NL Gebruiksaanwijzing
PT Instruções de serviço
DA Brugsanvisning
SV Bruksanvisning
NO Bruksanvisning
FI Käyttöohje
PL Instrukcja obslugi
HU Kezelési útmutató
EL Οδηγίεςχρήσεως
RU Инструкцияпоиспользованию
RO AG8000
Overview RO AG8000
1
2
3
A
5
6
7
8
9
10
4
12
11
RO BC14/36, RO BP18/2-18/4
B
1
5 6
100%
75%
50%
25%
<20%
RO BP18/2 no.: 1000001652
18V - 2,0Ah
RO BP18/4 no.: 1000001653
18V - 4,0Ah
2
4
3
RO BC14/36 no.:
1000001654- 230V Typ C
1000001655- 230V Typ I
1000001656- 110V Typ A
1000001691- 230V Typ G
Intro
EU-KONFORMITÄTSERKLÄRUNG
Wir erklären in alleiniger Verantwortung, dass dieses
Produkt mit den angegebenen Normen und Richtlinien
übereinstimmt.
EU-DECLARATION OF CONFORMITY
We declare on our sole accountability that this product
conforms to the standards and guidelines stated.
DECLARATION EU DE CONFORMITÉ
Nous déclarons sous notre propre responsabilité que ce
produit est conforme aux normes et directives indiquées.
DECLARACION DE CONFORMIDAD EU
Declaramos, bajo nuestra responsabilidad exclusiva, que
este producto cumple con las normas y directivas
mencionadas.
DICHARAZIONE DI CONFORMITÀ EU
Dichiariamo su nostra unica responsabilità, che questo
prodotto è conforme alle norme ed alle direttive indicate.
EU-KONFORMITEITSVERKLARING
Wij verklaren in eigen verantwoordelijkheid dat dit
product overeenstemt met de van toepassing zijnde
normen en richtlijnen.
DECLARAÇÃO DE CONFORMIDADE EU
Declaramos, sob responsabilidade exclusiva, que o
presente produto está conforme com as Normas e
Directivas indicadas.
EU-KONFORMITETSERKLÆRING
Vi erklærer som eneansvarlig, at dette produkt er i
overensstemmelse med anførte standarder,
retningslinjer og direktiver.
EU-FÖRSÄKRAN
Vi försäkrar på eget ansvar att denna produkt uppfyller
de angivna normerna och riktlinjerna.
EU-SAMSVARSERKLÆRING
Vi erklærer på eget ansvar at dette produktet stemmer
overens med de følgende normer eller normative
dokumenter.
TODISTUS EU-STANDARDINMUKAISUUDESTA
Todistamme täten ja vastaamme yksin siitä, että tämä
tuote on allalueteltujen standardien ja
standardomisasiakirjojen vaatimusten mukainen.
DEKLARACJA ZGODNOŚCI EU
Oświadczamy z pełną odpowiedzialnością, że produkt
ten odpowiada wymaganiom następujących norm i
dokumentów normatywnych.
EU-AZONOSSÁGI NYILATKOZAT
Teljes felelősségünk tudatában kijelentjük, hogy jelen
termék megfelel a következő szabványoknak vagy
szabványossági dokumentumoknak.
ΔΗΛΩΣΗ ΣΥΜΜΟΡΦΩΣΗΣ ΕΕ
Δήλώνουμε με αποκλειστική μας ευθύvη, ότι αυτό το
προϊόv αvταποκρίvεται στα ακόλουθα πρότυπα ή
έγγραφα τυποποίησης.
ДЕКЛАРАЦИЯ О СООТВЕТСТВИИ СТАНДАРТАМ
EU.
Мы заявляем что этот продукт соответствует
следующим стандартам.
RO AG8000:
2006/42/EG, 2014/30/EU, 2011/65/EU, EN 60745-1,
EN 60745-2-3, EN 55014-1, EN 55014-2, EN 50581
RO BC14/36:
2014/35/EU, 2014/30/EU, 2011/65/EU, EN 62233,
EN 60335-1, EN 60335-2-29, EN 55014-1, EN 55014-2,
EN 61000-3-2, EN 61000-3-3, EN 50581
Herstellerunterschrift
Manufacturer / authorized representative signature
ppa. Thorsten Bühl Kelkheim, 25.02.2016
Director Corporate Technology
Technische Unterlagen bei / Technical file at:
ROTHENBERGER Werkzeuge GmbH
Spessartstrasse 2-4
D-65779 Kelkheim/Germany
ENGLISH 17
Contents
Page
1 Safety Notes ........................................................................................................................ 18
1.1 Intended use..................................................................................................................... 18
1.2 General Power Tool Safety Warnings ............................................................................... 18
1.3 Special safety instructions ................................................................................................ 20
2 Technical Data RO AG8000 ................................................................................................ 24
2.1 Technical Data RO BC14/36 Charger, RO BP18/2 and RO BP18/4 battery ...................... 25
3 Function of the Unit ............................................................................................................ 25
3.1 Overview RO AG8000 (A) ................................................................................................ 25
3.2 Overview RO BC14/36 Charger, RO BP18/2 and RO BP18/4 battery (B) ......................... 25
3.3 Start of operation .............................................................................................................. 25
3.4 Attaching the grinding wheel ............................................................................................. 27
3.5 Operating ......................................................................................................................... 27
4 Troubleshooting RO AG8000 ............................................................................................. 29
5 Care and Maintenance ........................................................................................................ 29
6 Accessories......................................................................................................................... 29
7 Customer service ................................................................................................................ 29
8 Disposal ............................................................................................................................... 29
Markings in this document:
Danger!
This sign warns against the danger of personal injuries.
Caution!
This sign warns against the danger of property damage and damage to the envi-
ronment.
Call for action
18 ENGLISH
1 Safety Notes
1.1 Intended use
The user bears sole responsibility for any damage caused by improper use.
Generally accepted accident prevention regulations and the enclosed safety information must be
observed.
RO AG8000:
The cordless angle grinders, when fitted with original ROTHENBERGER accessories, are suita-
ble for grinding, sanding, cutting-off and wire brushing metal, concrete, stone and similar materi-
als without the use of water.
RO BC14/36 Charger, RO BP18/2 and RO BP18/4 battery:
The chargers are only suitable for charging ROTHENBERGER RO BP battery packs.
This tool is not designed for use by persons with physical, sensory or mental disabilities, or with
insufficient experience and/or knowledge, unless they are supervised by a person responsible
for their safety, or have received instructions on how to use the tool by this person.
Never attempt to charge batteries that are not rechargeable. Danger of explosion!
The battery packs are designed for use in corresponding ROTHENBERGER battery-operated
power tools. They must only be charged using ROTHENBERGER RO BC14/36 chargers. To se-
lect the appropriate device, please contact your ROTHENBERGER dealer. Read the relevant
instructions for the devices used.
1.2 General Power Tool Safety Warnings
WARNING!
Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may result in electric shock, fire and/or serious in-
jury.
Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your electrically-operated (corded) power tool or
battery-operated (cordless) power tool.
1) Work area safety
a) Keep work area clean and well lit. Cluttered and dark areas invite accidents.
b) Do not operate power tools in explosive atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or
fumes.
c) Keep children and bystanders away while operating a power tool. Distractions can
cause you to lose control.
2) Electrical safety
a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not use
any adapter plugs with (grounded) power tools. Unmodified plugs and matching outlets
will reduce risk of electric shock.
b) Avoid body contact with grounded surfaces such as pipes, radiators, ranges and re-
frigerators. There is an increased risk of electric shock if your body is grounded.
c) Do not expose power tools to rain or wet conditions. Water entering a power tool will in-
crease the risk of electric shock.
d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the
power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or
entangled cords increase the risk of electric shock.
e) When operating a power tool outdoors only, use an extension cords suitable for out-
door use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
f) If operating a power tool in a damp location is unavoidable, use a residual current de-
vice (RCD) protected supply. Use of an RCD reduces the risk of electric shock.
3) Personal safety
ENGLISH 19
a) Stay alert, watch what you are doing and use common sense when operating a power
tool. Do not use a power tool while you are tired or under the influence of drugs, al-
cohol or medication. A momentary lack of attention while operating power tools may result
in serious personal injury.
b) Use personal protective equipment. Always wear eye protection. Protective equipment
such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropri-
ate conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the switch is in the off-position before connect-
ing to power source and/or battery pack, picking up or carrying the tool. Carrying
power tools with your finger on the switch or energising power tools that have the switch on
invites accidents.
d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a
key left attached to a rotating part of the power tool may result in personal injury.
e) Do not overreach. Keep proper footing and balance at all times. This enables better
control of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and
gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in
moving parts.
g) If devices are provided for the connection of dust extraction and collection facilities,
ensure these are connected and properly used. Use of these devices can reduce dust re-
lated hazards.
4) Power tool use and care
a) Do not force the power tool. Use the correct power tool for your application. The cor-
rect power tool will do the job better and safer at the rate for which it was designed.
b) Do not use the power tool if the switch does not turn it on and off. Any power tool that
cannot be controlled with the switch is dangerous and must be repaired.
c) Disconnect the plug from the power source and/or the battery pack from the power
tool before making any adjustments, changing accessories, or storing power tools.
Such preventive safety measures reduce the risk of starting the power tool accidentally.
d) Store idle power tools out of the reach of children and do not allow persons unfamil-
iar with the power tool or these instructions to operate the power tool. Power tools are
dangerous in the hands of untrained users.
e) Maintain power tools. Check for misalignment or binding of moving parts, breakage
of parts and any other condition that may affect the power tools operation. If dam-
aged, have the power tool repaired before use. Many accidents are caused by poorly
maintained power tools.
f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting
edges are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc., in accordance with these instruc-
tions, taking into account the working conditions and the work to be performed. Use
of the power tool for operations different from those intended could result in a hazardous sit-
uation.
5) Battery tool use and care
a) Recharge only with the charger specified by the manufacturer. A charger that is suita-
ble for one type of battery pack may create a risk of fire when used with another battery
pack.
b)
WARNING! Use power tools only with specifically designated battery packs
and respectively battery types. Use of any other battery packs may create a risk
of explosions, injury and fire.
c) When battery pack is not in use, keep it away from other metal objects like paper
clips, coins, keys, nails, screws, or other small metal objects that can make a connec-
tion from one terminal to another. Shorting the battery terminals together may cause
burns or a fire.
20 ENGLISH
d) Under abusive conditions, liquid may be ejected from the battery; avoid contact. If
contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek
medical help. Liquid ejected from the battery may cause irritation or burns.
6) Service
Have your power tool serviced by a qualified repair person using only identical re-
placement parts. This will ensure that the safety of the power tool is maintained.
1.3 Special safety instructions
RO AG8000:
Safety Warnings Common for Grinding, Sanding, Wire Brushing or Abrasive Cutting-Off Opera-
tions:
a) This power tool is intended to function as a grinder, sander, wire brush or cut-off tool.
Read all safety warnings, instructions, illustrations and specifications provided with this
power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or
serious injury.
b) Operations such as polishing are not recommended to be performed with this power
tool. Operations for which the power tool was not designed may create a hazard and cause per-
sonal injury.
c) Do not use accessories which are not specifically designed and recommended by the
tool manufacturer. Just because the accessory can be attached to your power tool, it does not
assure safe operation.
d) The rated speed of the accessory must be at least equal to the maximum speed
marked on the power tool. Accessories running faster than their rated speed can break and fly
apart.
e) The outside diameter and the thickness of your accessory must be within the capacity
rating of your power tool. Incorrectly sized accessories cannot be adequately guarded or con-
trolled.
f) Threaded mounting of accessories must match the grinder spindle thread. For acces-
sories mounted by flanges, the arbour hole of the accessory must fit the locating diame-
ter of the flange. Accessories that do not match the mounting hardware of the power tool will
run out of balance, vibrate excessively and may cause loss of control.
g) Do not use a damaged accessory. Before each use inspect the accessory such as
abrasive wheels for chips and cracks, backing pad for cracks, tear or excess wear, wire
brush for loose or cracked wires. If a power tool or accessory is dropped, inspect for
damage or install an undamaged accessory. After inspecting and installing an accessory,
position yourself and bystanders away from the plane of the rotating accessory and run
the power tool at maximum no-load speed for one minute. Damaged accessories will nor-
mally break apart during this test time.
h) Wear personal protective equipment. Depending on application, use face shield, safety
goggles or safety glasses. As appropriate, wear dust mask, hearing protectors, gloves
and workshop apron capable of stopping small abrasive or workpiece fragments. The eye
protection must be capable of stopping flying debris generated by various operations. The dust
mask or respirator must be capable of filtering particles generated by your operation. Prolonged
exposure to high intensity noise may cause hearing loss.
i) Keep bystanders a safe distance away from work area. Anyone entering the work area
must wear personal protective equipment. Fragments of workpiece or of a broken accessory
may fly away and cause injury beyond immediate area of operation.
j) Hold power tool by insulated gripping surfaces only, when performing an operation
where the cutting accessory may contact hidden wiring or its own cord. Cutting accessory
contacting a "live" wire may make exposed metal parts of the power tool "live" and shock the
operator.
k) Position the cord clear of the spinning accessory. If you lose control, the cord may be cut
or snagged and your hand or arm may be pulled into the spinning accessory.
I) Never lay the power tool down until the accessory has come to a complete stop. The
spinning accessory may grab the surface and pull the power tool out of your control.
ENGLISH 21
m) Do not run the power tool while carrying it at your side. Accidental contact with the spin-
ning accessory could snag your clothing, pulling the accessory into your body.
n) Regularly clean the power tool’s air vents. The motor’s fan will draw the dust inside the
housing and excessive accumulation of powdered metal may cause electrical hazards.
o) Do not operate the power tool near flammable materials. Sparks could ignite these mate-
rials.
p) Do not use accessories that require liquid coolants. Using water or other liquid coolants
may result in electrocution or shock.
Kickback and Related Warnings:
Kickback is a sudden reaction to a pinched or snagged rotating wheel, backing pad, brush or
any other accessory. Pinching or snagging causes rapid stalling of the rotating accessory which
in turn causes the uncontrolled power tool to be forced in the direction opposite of the accesso-
ry’s rotation at the point of the binding.
For example, if an abrasive wheel is snagged or pinched by the workpiece, the edge of the
wheel that is entering into the pinch point can dig into the surface of the material causing the
wheel to climb out or kick out. The wheel may either jump toward or away from the operator, de-
pending on direction of the wheel’s movement at the point of pinching. Abrasive wheels may al-
so break under these conditions.
Kickback is the result of power tool misuse and/or incorrect operating procedures or conditions
and can be avoided by taking proper precautions as given below.
a) Maintain a firm grip on the power tool and position your body and arm to allow you to
resist kickback forces. Always use auxiliary handle, if provided, for maximum control
over kickback or torque reaction during start-up. The operator can control torque reactions
or kickback forces, if proper precautions are taken.
b) Never place your hand near the rotating accessory. Accessory may kickback over your
hand.
c) Do not position your body in the area where power tool will move if kickback occurs.
Kickback will propel the tool in direction opposite to the wheel’s movement at the point of snag-
ging.
d) Use special care when working corners, sharp edges etc. Avoid bouncing and snag-
ging the accessory. Corners, sharp edges or bouncing have a tendency to snag the rotating
accessory and cause loss of control or kickback.
e) Do not attach a saw chain woodcarving blade or toothed saw blade. Such blades create
frequent kickback and loss of control.
Safety Warnings Specific for Grinding and Cutting-Off Operations:
a) Use only wheel types that are recommended for your power tool and the specific guard
designed for the selected wheel. Wheels for which the power tool was not designed cannot be
adequately guarded and are unsafe.
b) The grinding surface of centre depressed wheels must be mounted below the plane of
the guard lip. An improperly mounted wheel that projects through the plane of the guard lip
cannot be adequately protected.
c) The guard must be securely attached to the power tool and positioned for maximum
safety, so the least amount of wheel is exposed towards the operator. The guard helps to
protect the operator from broken fragments, accidental contact with the wheel and sparks which
could ignite clothing.
d) Wheels must be used only for recommended applications. For example: do not grind
with the side of cut-off wheel. Abrasive cut-off wheels are intended for peripheral grinding,
side forces applied to these wheels may cause them to shatter.
e) Always use undamaged wheel flanges that are of correct size and shape for your se-
lected wheel. Proper wheel flanges support the wheel thus reducing the possibility of wheel
breakage. Flanges for cut-off wheels may be different from grinding wheel flanges.
f) Do not use worn down wheels from larger power tools. Wheels intended for larger power
tools are not suitable for the higher speed of a smaller tool and may burst.
Additional Safety Warnings Specific for Abrasive Cutting-Off Operations:
22 ENGLISH
a) Do not “jam” the cut-off wheel or apply excessive pressure. Do not attempt to make an
excessive depth of cut. Overstressing the wheel increases the loading and susceptibility to
twisting or binding of the wheel in the cut and the possibility of kickback or wheel breakage.
b) Do not position your body in line with and behind the rotating wheel. When the wheel, at
the point of operation, is moving away from your body, the possible kickback may propel the
spinning wheel and the power tool directly at you.
c) When wheel is binding or when interrupting a cut for any reason, switch off the power
tool and hold the power tool motionless until the wheel comes to a complete stop. Never
attempt to remove the cut-off wheel from the cut while the wheel is in motion otherwise
kickback may occur. Investigate and take corrective action to eliminate the cause of wheel
binding.
d) Do not restart the cutting operation in the workpiece. Let the wheel reach full speed
and carefully reenter the cut. The wheel may bind, walk up or kickback if the power tool is re-
started in the workpiece.
e) Support panels or any oversized workpiece to minimize the risk of wheel pinching and
kickback. Large workpieces tend to sag under their own weight. Supports must be placed under
the workpiece near the line of cut and near the edge of the workpiece on both sides of the
wheel.
f) Use extra caution when making a "pocket cut" into existing walls or other blind areas.
The protruding wheel may cut gas or water pipes, electrical wiring or objects that can cause
kickback.
Safety Warnings Specific for Sanding Operations:
a) Do not use excessively oversized sanding disc paper. Follow manufacturer's recom-
mendations when selecting sanding paper. Larger sanding paper extending beyond the
sanding pad presents a laceration hazard and may cause snagging, tearing of the disc or kick-
back.
Safety Warnings Specific for Wire Brushing Operations:
a) Be aware that wire bristles are thrown by the brush even during ordinary operation. Do
not overstress the wires by applying excessive load to the brush. The wire bristles can eas-
ily penetrate light clothing and/or skin.
b) If the use of a guard is recommended for wire brushing, do not allow any interference
of the wire wheel or brush with the guard. Wire wheel or brush may expand in diameter due
to work load and centrifugal forces.
Additional Safety Instructions:
WARNING Always wear protective goggles
Use elastic cushioning layers if they have been supplied with the abrasive and if required.
Observe the specifications of the tool or accessory manufacturer! Protect the discs from grease
or impacts!
Grinding discs must be stored and handled with care in accordance with the manufacturer's in-
structions.
Never use parting grinder discs for roughing work! Do not apply pressure to the side of parting
grinder discs.
The workpiece must lay flat and be secured against slipping, e.g. using clamps. Large workpiec-
es must be sufficiently supported.
If accessories with threaded inserts are used, the end of the spindle may not touch the base of
the hole on the grinding tool. Make sure that the thread in the accessory is long enough to ac-
commodate the full length of the spindle. The thread in the accessory must match the thread on
the spindle. See technical Specifications for more information on the spindle length and thread.
Use of a fixed extractor system is recommended.
Dust from material such as paint containing lead, some wood species, minerals and metal may
be harmful. Contact with or inhalation of the dust may cause allergic reactions and/or respiratory
diseases to the operator or bystanders.
ENGLISH 23
Certain kinds of dust are classified as carcinogenic such as oak and beech dust especially in
conjunction with additives for wood conditioning (chromate, wood preservative). Material con-
taining asbestos must only be treated by specialists.
-Where the use of a dust extraction device is possible it shall be used.
-The work place must be well ventilated.
-The use of a dust mask of filter class P2 is recommended.
Follow national requirements for the materials you want to work with.
Materials that generate dusts or vapours that may be harmful to health (e.g. asbestos) must not
be processed.
When working in dusty conditions, ensure that ventilation openings are not blocked. If it be-
comes necessary to remove dust, first remove the battery pack (use non-metallic objects) and
avoid damaging internal components.
Damaged, eccentric or vibrating tools must not be used.
Avoid damage to gas or water pipes, electrical cables and load-bearing walls (static).
Remove the battery pack from the machine before any adjustments, conversions or servicing
are performed.
Before fitting the battery pack, make sure that the machine is switched off.
A damaged or cracked additional handle must be replaced. Never operate a machine with a de-
fective additional handle.
A damaged or cracked safety guard must be replaced. Never operate a machine with a defec-
tive safety guard.
RO BC14/36 Charger, RO BP18/2 and RO BP18/4 battery:
This charger is not intended for use by children and persons
with physical, sensory or mental limitations or a lack of experi-
ence or knowledge. This charger can be used by children aged 8
and above and by persons who have physical, sensory or mental
limitations or a lack of experience or knowledge if a person re-
sponsible for their safety supervises them or has instructed
them in the safe operation of the charger and they understand
the associated dangers. Otherwise, there is a danger of operating
errors and injuries.
Supervise children during use, cleaning and maintenance. This
will ensure that children do not play with the charger.
Do not charge non-rechargeable batteries.
Danger - electrical voltage!!
Only use the charger indoors!
Protect the charger from moisture!
Never allow children to use the machine. Children should be supervised to ensure that they do
not play with the tool.
Keep children away from the battery charger and the working area!
Keep your battery charger out of reach of children!
Pull out the mains plug immediately if the battery charger starts to smoke or flames emerge!
Do not insert objects into the ventilation slots on the battery charger there is a danger of elec-
tric shocks and short circuits!
Do not recharge a fully charged battery pack!
24 ENGLISH
Protect battery packs from water and moisture!
Do not expose battery packs to naked flame!
Do not use faulty or deformed battery packs!
Do not open battery packs!
Do not touch or short-circuit battery packs!
Slightly acidic, flammable fluid may leak from defective Li-ion battery packs!
If battery fluid leaks out and comes into contact with your skin, rinse immediately
with plenty of water. If battery fluid leaks out and comes into contact with your eyes,
wash them with clean water and seek medical attention immediately!
Transporting li-ion battery packs: The shipping of li-ion battery packs is subject to laws relat-
ing to the carriage of hazardous goods (UN 3480 and UN 3481). Inform yourself of the currently
valid specifications when shipping li-ion battery packs. If necessary, consult your freight for-
warder. Certified packaging is available from ROTHENBERGER.
2 Technical Data RO AG8000
RO AG8000 without battery, art.-no.: 1300003381
Voltage of battery pack .....................................................................
18V
max. diameter of accessory ..............................................................
125mm / 5 in.
max. permitted thickness of clamping shank on accessory when
using "Quick"clamping nut (2) ...........................................................
6mm / ¼ in.
Roughing disc/Parting disc: max. permitted thickness of accessory ..
6mm / ¼ in.
Spindle thread ..................................................................................
M14 / 25 in.
Length of the grinding spindle ...........................................................
20mm / 32 in.
No-load speed (maximum speed) .....................................................
8000 min
-1
Weight without battery ......................................................................
2,4 kg / 5.3 lbs
Vibration total value (vector sum of three directions):
Vibration emission value, sanding surfaces (a
h,SG
) ............................
4,5 m/¦ K
h,SG
1,5 m/s²
Vibration emission value, sanding with sanding pad (a
h,DS
) ...............
< 2,5 m/s² ¦ K
h,DS
1,5 m/s²
Sound pressure level (L
pA
) ................................................................
83 dB (A) ¦ K
pA
3 dB (A)
Acoustic power level (L
WA
) ................................................................
94 dB (A) ¦ K
WA
3 dB (A)
The noise level during operation can exceed 80 dB (A). Wear hearing protection!
Measured values determined in accordance with EN 60745.
ENGLISH 25
2.1 Technical Data RO BC14/36 Charger, RO BP18/2 and RO BP18/4 battery
Battery, art.-no.: 2,0Ah 1000001652 /
4,0 Ah 1000001653
Charger, art. no.: EU 1000001654 /
AUS 1000001655 / USA CND 1000001656/
UK 1000001691
Typ/ model ......................................
RO BP18/2
RO BP18/4
Li-Ion Battery
Typ/ model ........................................
RO BC14/36
Charger for 18V Li-
Ion Akku
Voltage ...........................................
18 V DC
Input voltage .....................................
220V 240V AC /
100 120´V AC
Capacity .........................................
2,0 Ah / 4,0 Ah
Charging voltage.............................
20,75 V DC
Input frequency .................................
50 60 Hz
Charge current ................................
4A / 8A
Input power .......................................
85 W
Charging temperature .....................
0° - 46° C
Charging voltage ...............................
12-42V DC
Max. discharging temperature. ........
-15°C +75°C
Max. charge current ..........................
3A
Approx. charging time (90% full) .....
ca. 40 / 80 min.
Rated output .....................................
68 W
Weight ............................................
ca. 400 / 670g
No. of battery cells ............................
4-10
Recharge battery pack before first use!
Weight ..............................................
ca. 600 g
Pay attention to the electrical outlet
voltage! Check the label on the
bottom of the charger!
3 Function of the Unit
3.1 Overview RO AG8000 (A)
1
Clip to tighten/release the (tool-free)
clamping nut manually
7
Electronic signal indicator
2
Clamping nut (tool-free)
8
Battery pack release button
3
Support flange
9
Battery pack
4
Spindle
10
Dust filter
5
Spindle locking button
11
Additional handle
6
Sliding on/off switch
12
Safety cover
3.2 Overview RO BC14/36 Charger, RO BP18/2 and RO BP18/4 battery (B)
1
Battery pack
4
Warning display
2
Sliding seat
5
Capacity indicator button
3
Operation display
6
Capacity and signal indicator
3.3 Start of operation
RO AG8000 (fig. A):
Attaching the additional handle.
Always work with the additional handle attached (11)! Attach the additional handle
on the left or right of the machine and secure.
Install safety guard.
For safety reasons, always use the safety guard provided for the respective wheel!
See also chapter accessorie.
Safety guard for grinding:
Designed for work with roughing wheels, flap sanding pads, diamond cut-off wheels.
26 ENGLISH
Pull on the lever (15). Place the safety guard (12) in the position indicated.
Release the lever and turn the safety guard until the lever engages.
Pull on the (15) lever and turn the safety guard until the closed section is facing the operator.
Make sure that the guard is seated securely: the lever must engage and you should not be
able to turn the safety guard.
Use only accessories that are covered by at least 3.4 mm by the safety
guard.
Dust filter:
Always fit the dust filter if the surroundings are heavily
polluted (10).
The machine heats up faster when the dust filter is fitted
(10). It is protected by the electronics system from over-
heating (see chapter5.)
To fit:
Attach the dust filter (10) as shown.
To remove:
Holding the dust filter at the edges, raise it slightly (10) and then pull it downwards and re-
move.
Rotating battery pack:
The rear section of the machine can be rotated 270° in three
stages, thus allowing the machine's shape to be adapted to the
working conditions. Only operate the machine when it is in an
engaged position.
Removing and inserting the battery pack:
Removal:
Press the battery pack release (8) button and pull the battery pack (9) forwards.
Inserting:
Slide in the battery pack (9) until it engages.
RO BC14/36 Charger, RO BP18/2 and RO BP18/4 battery (fig. B):
Before plugging in, check to see that the rated mains voltage and mains fre-
quency, as specified on the rating label, match your power supply.
Devices such as this one, which generate direct current, may have an effect on basic residual-
current circuit breakers. Use type F or better, with a release current of max. 30 mA.
Before commissioning the charger, ensure that the air slots are free. Minimum
distance to other objects is 5 cm.
Self-test:
Insert mains supply plug.
The warning display (4) and the operating indicator (3) light up one after the other for approx. 1
second and the installed fan runs for approx. 5 seconds.
Battery pack:
Charge the battery pack before use (1).
If performance diminishes, recharge the battery pack.
ENGLISH 27
The ideal storage temperature is between 10°C and 30°C. The permissible storage temperature
is between 0°C and 50°C.
"Li-Power" li-ion battery packs have a capacity and signal indicator: (6)
Press the button (5), the LEDs indicate the charge level.
If one LED is flashing, the battery pack is almost flat and must be recharged.
3.4 Attaching the grinding wheel
Before carrying out any modifications: remove the battery pack from the ma-
chine. The machine must be switched off and the spindle at a standstill.
For reasons of safety, attach the parting guard before performing parting work
(see chapter accessories).
Locking the spindle:
Press in the spindle locking button (5) and turn the spindle (4) by hand until you feel the
spindle locking button engage.
Placing the grinding wheel in position:
Fit the support flange (3) on the spindle. The flange
should not turn on the spindle when properly attached.
Place the grinding wheel on the support flange (3). The
grinding wheel must lay flat on the supporting flange. The
metal flange on the parting grinder disc must lay flat on
the support flange
Note: The support flange (3) is secured to prevent it from falling off. To remove: use some force
if necessary.
Securing/releasing the (tool-free) clamping nut:
Only tighten the (tool-free) clamping nut (2) manually!
For the machine to operate, the clip (1) must always lie flat on clamping nut (2).
To secure the (tool-free) clamping nut (2):
Do not use the (tool-free) clamping nut if the accessory has a clamping shank thick-
er than 6 mm!
Lock the spindle.
Flip up the clip (1) on the clamping nut.
Fit the clamping nut (2) on the spindle (4).
Tighten the clamping nut on the clip (1) manually in a clockwise direction.
Flip down the clip (1) again.
To release the (tool-free) clamping nut (2):
Lock the spindle
Flip up the clip (1) on the clamping nut.
Unscrew the clamping nut (2) , turning it anticlockwise manually.
3.5 Operating
RO AG8000 (fig. A):
Switching On and Off:
Always guide the machine with both hands.
Switch on first, then guide the accessory towards the workpiece.
28 ENGLISH
The machine must not be allowed to draw in additional dust and shavings. When
switching the machine on and off, keep it away from dust deposits. After switching
off the machine, only place it down when the motor has come to a standstill.
Avoid switching on the machine accidentally: always switch it off when the battery
pack is removed from the machine.
In continuous operation, the machine continues running if it is forced out of your
hands. Therefore, always hold the machine with both hands using the handles
provided, stand in a safe position and concentrate.
Switching on: Push the slide switch (6)
forward. For continuous activation, now
tilt downwards until it engages.
Switching off: Press the rear end of the
slide switch (6) and release
Working instructions:
Grinding:
Press down the machine evenly on the surface and move back and forth so that the surface of
the workpiece does not become too hot.
Roughing: position the machine at an angle of 30° - 40° for the best working results.
Cutting-off:
Always work against the run of the disc (see illustration). Otherwise there is
the danger of the machine kicking back from the cut out of control. Guide the
machine evenly at a speed suitable for the material being processed. Do not
tilt, apply excessive force or sway from side to side.
Sanding:
Press down the machine evenly on the surface and move back and forth so that the surface
of the workpiece does not become too hot.
Wire brushing:
Press down the machine evenly.
RO BC14/36 Charger, RO BP18/2 and RO BP18/4 battery (fig. B):
Charging battery pack:
Push the battery pack completely to the stop on the sliding seat (2).
The operating indicator (3) flashes.
Conservation charge:
Once the charging process has finished, the battery charger automatically switches to conserva-
tion mode.
The battery pack can remain in the battery charger and is therefore always ready for use.
The operating display (3) lights up continuously.
Fault:
● Warning display (4) lights up continuously.
Battery pack is not charged. Temperature too high/ too low. When the temperature of the battery
pack is between 0 °C and 50 °C, the charging process begins automatically.
● Warning display (4) flashes.
Battery pack is defective. Remove the battery pack immediately from the charger.
ENGLISH 29
The battery pack was not pushed correctly onto the sliding seat (2).
4 Troubleshooting RO AG8000
Symptom
Possible Reason
Solution
The electronic signal display (7)
lights up and the load speed
decreases. The temperature is
too high!
Run the machine in idling until the
electronics signal indicator switches
off.
The electronic signal display (7)
flashes and the machine does
not start. The restart protection
is active.
The machine will not start if the battery
pack is inserted while the machine is
on. Switch the machine off and on
again.
5 Care and Maintenance
RO AG8000:
Cleaning:
Clean the dust filter regularly: remove and clean with a jet of compressed air.
RO BC14/36 Charger:
Repairs to the charger must only be carried out by qualified electricians.
If the mains connection cable of this tool is damaged, in order to prevent endangering personnel
and property it must be replaced by the manufacturer, or the Customer Service of the manufac-
turer, or a similarly qualified person.
6 Accessories
Accessory Name
ROTHENBERGER Part Number
INOX PROFI Plus Cutting disc 125x1.0, box
071534D
SAFE CUT Cutting disc 125x2/1, box
071552D
2 IN 1 Cutting and grinding disk 125x2,5, box
071554D
www.rothenberger.com
7 Customer service
The ROTHENBERGER service locations are available to help you (see listing in catalog or on-
line) and replacement parts and service are also available through these same service locations.
Order your accessories and spare parts from your specialist retailer or using our service-after-
sales hotline:
Phone: + 49 (0) 61 95 / 800 8200 Fax: + 49 (0) 61 95 / 800 7491
Email: service@rothenberger.com
www.rothenberger.com
8 Disposal
Components of the unit are recyclable material and should be put to recycling. For this purpose
registered and certified recycling companies are available. For an environmental friendly dispos-
al of the non-recyclable parts (e.g. electronic waste) please contact your local waste disposal
authority.
Old batteries can be taken to your specialist dealer who will dispose of them in conformity with
environmental regulations.
For EU countries only:
Do not dispose of electric tools with domestic waste. In accordance with European
Directive 2012/19/EC on waste electrical and electronic equipment and its implementa-
tion as national law, electric tools that are no longer serviceable must be collected
separately and utilised for environmentally compatible recycling.
1300003470-i0/F&E
www.rothenberger.com
ROTHENBERGER Worldwide
Austria
Belgium
Brazil
Bulgaria
China
Czech
Republic
Denmark
France
Germany
Hungary
India
Greece
ROTHENBERGER Italiana s.r.l.
Via G. Reiss Romoli 17-19 • I-20019 Settimo Milanese
Tel. + 39 02 / 33 50 601 • Fax + 39 02 / 33 50 0151
info@rothenberger.it • www.rothenberger.it
ROTHENBERGER Nederland bv
Postbus 45 • NL-5120 AA Rijen
Tel. + 31 1 61 / 29 35 79 • Fax + 31 1 61 / 29 39 08
info@rothenberger.nl • www.rothenberger.nl
ROTHENBERGER Polska Sp.z.o.o.
Ul. Annopol 4A • Budynek C • PL-03-236 Warszawa
Tel. + 48 22 / 2 13 59 00 • Fax + 48 22 / 2 13 59 01
biuro@rothenberger.pl • www.rothenberger.pl
ROTHENBERGER Russia
Avtosavodskaya str. 25
115280 Moscow, Russia
Tel. + 7 495 / 792 59 44 • Fax + 7 495 / 792 59 46
info@rothenberger.ru • www.rothenberger.ru
ROTHENBERGER-TOOLS SA (PTY) Ltd.
P.O. Box 4360 • Edenvale 1610
165 Vanderbijl Street, Meadowdale Germiston
Gauteng (Johannesburg), South Africa
Tel. + 27 11 / 3 72 96 31 • Fax + 27 11 / 3 72 96 32
info@rothenberger.co.za • www.rothenberger.co.za
ROTHENBERGER S.A.
Ctra. Durango-Elorrio, Km 2 • E-48220 Abadiano
(Vizcaya)
(P.O. Box) 117 • E-48200 Durango (Vizcaya)
Tel. + 34 94 / 6 21 01 00 • Fax + 34 94 / 6 21 01 31
export@rothenberger.es • www.rothenberger.es
ROTHENBERGER Sweden AB
Hemvärnsgatan 22 • S- 171 54 Solna, Sverige
Tel. + 46 8 / 54 60 23 00 • Fax + 46 8 / 54 60 23 01
roswe@rothenberger.se • www.rothenberger.se
ROTHENBERGER (Schweiz) AG
Herostr. 9 • CH-8048 Zürich
Tel. + 41 44 / 435 30 30 • Fax + 41 44 / 401 06 08
ROTHENBERGER TÜRKIYE
ROTHENBERGER Center, Barbaros Bulvarı No:9
TR-34775 Şerifali / Ümraniye-Istanbul
Tel. + 90 / 216 449 24 85 • Fax + 90 / 216 449 24 87
rothenberger@rothenberger.com.tr
www.rothenberger.com.tr
ROTHENBERGER Middle East FZCO
PO Box 261190 • Jebel Ali Free Zone
Dubai, United Arab Emirates
Tel. + 971 / 48 83 97 77 • Fax + 971 / 48 83 97 57
ofce@rothenberger.ae
ROTHENBERGER EQUIPMENT TRADING &
SERVICES LLC
PO Box 91208 • Mussafah Industrial Area
Abu Dhabi, United Arab Emirates
Tel. + 971 / 25 50 01 54 • + 971 / 25 50 01 53
uaesales@rothenberger.ae
ROTHENBERGER UK Limited
2, Kingsthorne Park, Henson Way,
Kettering • GB-Northants NN16 8PX
Tel. + 44 15 36 / 31 03 00 • Fax + 44 15 36 / 31 06 00
info@rothenberger.co.uk
ROTHENBERGER USA LLC
7130 Clinton Road • Loves Park, IL 61111, USA
Tel. +1 / 80 05 45 76 98 • Fax + 1 / 81 56 33 08 79
www.rothenberger-usa.com
Italy
Nether-
lands
Poland
Russia
South
Africa
Spain
Switzerland
Turkey
UAE
UK
USA
ROTHENBERGER Werkzeuge GmbH
Industriestraße 7
D- 65779 Kelkheim / Germany
Telefon + 49 (0) 61 95 / 800 - 0
Fax + 49 (0) 6195 / 800 - 3500
info@rothenberger.com
ROTHENBERGER Australia Pty. Ltd.
Unit 6 • 13 Hoyle Avenue • Castle Hill • N.S.W. 2154
Tel. + 61 2 / 98 99 75 77 • Fax + 61 2 / 98 99 76 77
rothenberger@rothenberger.com.au
www.rothenberger.com.au
ROTHENBERGER Werkzeuge- und Maschinen
Handelsgesellschaft m.b.H.
Gewerbeparkstraße 9 • A-5081 Anif
Tel. + 43 62 46 / 7 20 91-45 • Fax + 43 62 46 / 7 20 91-15
ofce@rothenberger.at • www.rothenberger.at
ROTHENBERGER Benelux bvba
Antwerpsesteenweg 59 • B-2630 Aartselaar
Tel. + 32 3 / 8 77 22 77 • Fax + 32 3 / 8 77 03 94
info@rothenberger.be • www.rothenberger.be
ROTHENBERGER do Brasil LTDA
Av. Fagundes de Oliveira, 538 - Galpão A4
09950-300 - Diadema / SP - Brazil
Tel. + 55 11 / 40 44- 4748 • Fax + 55 11 / 40 44- 5051
spacente@rothenberger.com.br • www.rothenberger.com.br
ROTHENBERGER Bulgaria GmbH
Boul. Sitnjakovo 79 • BG-1111 Soa
Tel. + 35 9 / 2 9 46 14 59 • Fax + 35 9 / 2 9 46 12 05
info@rothenberger.bg • www.rothenberger.bg
ROTHENBERGER Pipe Tool (Shanghai) Co., Ltd.
D-4, No.195 Qianpu Road,East New Area of Songjiang
Industrial Zone, Shanghai 201611, China
Tel. + 86 21 / 67 60 20 61 • + 86 21 / 67 60 20 67
Fax + 86 21 / 67 60 20 63 • ofce@rothenberger.cn
ROTHENBERGER CZ
Prumyslova 1306/7 • 102 00 Praha 10
Tel. +420 271 730 183 • Fax +420 267 310 187
prodej@rothenberger.cz • www.rothenberger.cz
ROTHENBERGER Scandinavia A/S
Smedevænget 8 • DK-9560 Hadsund
Tel. + 45 98 / 15 75 66 • Fax + 45 98 / 15 68 23
roscan@rothenberger.dk
ROTHENBERGER France S.A.
24, rue des Drapiers, BP 45033 • F-57071 Metz Cedex 3
Tel. + 33 3 / 87 74 92 92 • Fax + 33 3 / 87 74 94 03
info-fr@rothenberger.com • www.rothenberger.fr
ROTHENBERGER Deutschland GmbH
Industriestraße 7 • D-65779 Kelkheim/Germany
Tel. + 49 61 95 / 800 81 00 • Fax + 49 61 95 / 800 37 39
verkauf-deutschland@rothenberger.com
www.rothenberger.com
ROTHENBERGER Werkzeuge Produktion GmbH
Lilienthalstraße 71- 87 • D-37235 Hessisch-Lichtenau
Tel. + 49 56 02 / 93 94-0 • Fax + 49 56 02 / 93 94 36
ROTHENBERGER Hellas S.A.
Agias Kyriakis 45 • 17564 Paleo Faliro • Greece
Tel. + 30 210 94 02 049 • +30 210 94 07 302 / 3
Fax + 30 210 / 94 07 322
[email protected] • www.rothenberger.com
ROTHENBERGER Hungary Kft.
Gubacsi út 26 • H-1097 Budapest
Tel. + 36 1 / 3 47- 50 40 • Fax + 36 1 / 3 47 - 50 59
info@rothenberger.hu • www.rothenberger.hu
ROTHENBERGER India Pvt. Ltd.
Plot No 17, Sector - 37, Pace city-I
Gurgaon, Haryana - 122 001, India
Tel. 91124- 4618900 • Fax 91124- 4019471
www.rothenberger.com
Australia
Sweden
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168
  • Page 169 169
  • Page 170 170
  • Page 171 171
  • Page 172 172
  • Page 173 173
  • Page 174 174
  • Page 175 175
  • Page 176 176
  • Page 177 177
  • Page 178 178
  • Page 179 179
  • Page 180 180
  • Page 181 181
  • Page 182 182
  • Page 183 183
  • Page 184 184
  • Page 185 185
  • Page 186 186
  • Page 187 187
  • Page 188 188
  • Page 189 189
  • Page 190 190
  • Page 191 191
  • Page 192 192
  • Page 193 193
  • Page 194 194
  • Page 195 195
  • Page 196 196
  • Page 197 197
  • Page 198 198
  • Page 199 199
  • Page 200 200
  • Page 201 201
  • Page 202 202
  • Page 203 203
  • Page 204 204
  • Page 205 205
  • Page 206 206
  • Page 207 207
  • Page 208 208
  • Page 209 209
  • Page 210 210
  • Page 211 211
  • Page 212 212
  • Page 213 213
  • Page 214 214
  • Page 215 215
  • Page 216 216
  • Page 217 217
  • Page 218 218
  • Page 219 219
  • Page 220 220
  • Page 221 221
  • Page 222 222
  • Page 223 223
  • Page 224 224

Rothenberger 1000001652 User manual

Category
Angle grinders
Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI