RS2767i
user manual
manual de usuario
It is important to read this instruction prior to using your new product
for the first time.
Es importante leer este manual antes de usar por vez primera su equipo.
Important information
FCC information
This device complies with part 15 of
the FCC Rules. Operation is subject
to the following two conditions: (1)
This device may not cause harmful
interference, and (2) this device
must accept any interference
received, including interference
that may cause undesired operation.
This equipment has been tested
and found to comply with the
limits for a Class B digital device,
pursuant to part 15 of the FCC
Rules. These limits are designed
to provide reasonable protection
against harmful interference in
a residential installation. This
equipment generates, uses and
can radiate radio frequency energy
and, if not installed and used in
accordance with the instructions,
may cause harmful interference
to radio communications.
However, there is no guarantee
that interference will not occur
in a particular installation. If this
equipment does cause harmful
interference to radio or television
reception, which can be determined
by turning the equipment off and
on, the user is encouraged to try to
correct the interference by one or
more of the following measures:
– Reorient or relocate the
receiving antenna.
– Increase the separation between
This audio system
has earned the
ENERGY STAR.
For your records
In the event that service should be
required, you may need the model
number and the serial number. In
the space below, record the date
and place of purchase and the
serial number:
Model No.:
Date of Purchase:
Place of Purchase:
Serial No.:
This Class B digital apparatus complies
with Canadian ICES-003.
the equipment and receiver.
– Connect the equipment into
an outlet on a circuit different
from that to which the receiver
is connected.
– Consult the dealer or an
experienced radio/TV technician
for help.
WARNING:
Changes or modifications
to this unit not expressly approved
by the party responsible for
compliance could void the user's
authority to operate the equipment.
Some of the following information
may not apply to your particular
product; however, as with any
electronic product, precautions
should be observed during
handling and use.
• Read these instructions.
• Keep these instructions.
• Heed all warnings.
• Follow all instructions.
• Do not use this apparatus near
water.
• Clean only with dry cloth.
• Do not block any ventilation
openings.
Install in accordance with the
manufacturer’s instructions.
• Do not install near any heat
sources such as radiators, heat
registers, stoves, or other
apparatus (including amplifi ers)
that produce heat.
• Do not defeat the safety
purpose of the polarized
or grounding-type plug. A
polarized plug has two blades
with one wider than the
other. A grounding type plug
has two blades and a third
grounding prong. The wide
blade or the third prong is
provided for your safety. If
the provided plug does not
fi t into your outlet, consult an
electrician for replacement of
the obsolete outlet.
• Protect the power cord
from being walked on or
pinched particularly at plugs,
convenience receptacles, and
the point where they exit from
the apparatus.
• Only use attachments/
accessories specifi ed by the
manufacturer.
• Use only with the
cart, stand, tripod,
bracket, or table
specifi ed by the
manufacturer, or sold with the
apparatus. When a cart is used,
use caution when moving the
cart/apparatus combination to
avoid injury from tip-over.
• Unplug this apparatus during
lightning storms or when
unused for long periods of time.
• Refer all servicing to qualifi ed
service personnel. Servicing is
required when the apparatus
has been damaged in any way,
such as power-supply cord or
plug is damaged, liquid has been
spilled or objects have fallen into
the apparatus, the apparatus
has been exposed to rain or
moisture, does not operate
normally, or has been dropped.
• ADDITIONAL SAFETY
INFORMATION
• Apparatus shall not be exposed
to dripping or splashing and
no objects fi lled with liquids,
such as vases, shall be placed
on the apparatus.
• Always leave suffi cient space
around the product for
ventilation. Do not place
product in or on a bed, rug,
in a bookcase or cabinet that
may prevent air fl ow through
vent openings.
• Do not place lighted candles,
cigarettes, cigars, etc. on the
product.
• Connect power cord only to
AC power source as marked on
the product.
•
Care should be taken so that
objects do not fall into the product.
• Do not attempt to disassemble
the cabinet. This product
does not contain customer
serviceable components.
• Where the main plug or an
appliance coupler is used as
the disconnect device, the
disconnect device shall remain
readily operable.
• IF YOUR PRODUCT OPERATES
ON BATTERIES, adhere to
the following precautions:
A. Any battery may leak
electrolyte if mixed with
a different battery type, if
inserted\ incorrectly, or if all
batteries are not replaced at
the same time.
B. Any battery may leak
electrolyte or explode if
disposed of in fi re or an attempt
is made to charge a battery not
intended to be recharged.
C. Discard leaky batteries
immediately. Leaking batteries
can cause skin burns or
other personal injury. When
discarding batteries, be sure to
dispose of them in the proper
manner, according to your state/
provincial and local regulations.
PLEASE READ AND SAVE THIS FOR FUTURE REFERENCE
IMPORTANT SAFETY INSTRUCTIONS
Precations
• This compact disc player
uses a laser to read the
music on the disc. The laser
mechanism corresponds to
the cartridge and stylus of a
record player. Although this
product incorporates a laser
pick-up lens, it is completely
safe when operated
according to directions.
• Discs rotate at high speed
inside the player. Do not
use damaged, warped, or
cracked discs.
• Do not touch the pick-up
lens which is located inside
the disc compartment. To
keep dust from collecting
on the pick-up lens, do not
leave the compartment
door open for an extended
period of time. If the lens
becomes dirty, clean it with
a soft brush, or use an air
blower brush designed for
camera lenses.
Headset safety
• Have a Blast-
Just Not in your
eardrums! Make
sure you turn
down the volume on the
unit before you put on
headphones. Increase the
volume to the desired level
only after headphone are in
place.
• Do not play your headset
at high volume. Hearing
experts warn against
extended high-volume play.
• If you experience ringing in
your ears, reduce volume or
discontinue use.
• You should use with extreme
caution or temporarily
discontinue use in potentially
hazardous situations.
Even if your headset is an
open-air designed to let you
to hear outside sounds, do
not turn up the volume so
high that you are unable to
hear what is around you.
Getting started
Unpacking the system
You should have the following:
• one main unit (with 2 main
speakers)
• one remote control
• one AM loop antenna
• one user manual
Connections
Back view
1. FM pigtail antenna
2. AM loop antenna jack
3. Main speaker jacks
Using FM and AM antennas
Before you use your audio
system, you’ll want to make sure
both the FM and AM antennas
are positioned properly. Uncoil
the FM antenna at the back of
the unit, making sure it is fully
extended (you may even want
to tape it to the wall behind the
unit if possible, the higher the
better).
You’ll also need to connect the
AM antenna loop to the back
of the unit if you listen to AM
stations. Rotate the AM loop
antenna for better reception.
Connecting main speakers
Each speaker has a black/red
wire and a black/purple wire.
When connecting the speakers,
match the red/purple wires to
the red/purple
jacks and the black wires to the
black jacks on the main unit.
Installation
To ensure sufficient ventilation,
keep the spacing shown below
free from other surfaces:
Front view
Side view
4”
4”4”
4”
2”
General controls
Main Unit
– To stop CD/iPod playback.
FOLDER/PRESET /
– to
select the previous or next
folder in mp3/wma disc mode;
to select the previous or next
preset stations in tuner mode.
SHUFFLE – To turn on/off
random CD playback.
PLAY MODE – To cycle between
different CD play mode.
LINE IN – Ø3.5mm jack for
external sound input.
AUX IN•L/R – Jacks for external
sound input.
BASS – To turn BASS on or off.
EQ – To select the equalizer
presets.
– Jack for connecting
headphones.
PUSH OPEN – Push to open /
close the iPod dock.
AUTO PROG•BAND – To
change between FM and AM
tuner bands; to enter auto
preset program in FM mode.
SOURCE – To select among CD
player, tuner, iPod and line in
/AUX sources.
ON/STANDBY – To turn power
on or off (STANDBY mode).
PROGRAM – To enter program
mode for CD and tuner.
CLOCK – To show time and
enter clock setting mode.
TIMER – To turn the timer on/
off; press and hold to enter the
timer setting mode.
DIMMER•DEMO – To turn the
feature demonstration on or
off; to adjust display brightness.
SLEEP – To select the time
interval in minutes before the
unit turns off.
– To open or close the disc tray.
DISC SKIP – To skip to the next
CD in the tray.
VOLUME – To increase/decrease
the volume.
/
– To tune radio
frequency; to skip CD/iPod
track; to fast search through the
CD/iPod.
– To play or pause CD/iPod.
Remote control
– To turn power on or off
(STANDBY mode).
CD – To select the CD player.
TUNER – To select the tuner
and change the radio band.
iPod – To select iPod playback.
LINE IN / AUX – To select the
external sound input from LINE
IN / AUX IN jacks.
CD tray status:
Lights when loaded
Flashes for the current disc
Animates when playing
Source indication
Display
Showing demonstration
Press and hold DIMMER•DEMO
for more than 2 seconds to turn
on/off demonstration mode.
The demonstration scrolls
through all display operations.
Display brightness
Press DIMMER•DEMO
repeatedly to select the desired
level (DIM 1 – 3).
Clock and timer
Setting the clock
1.
Press and hold CLOCK until
the hour fl ashes on the display.
2. Press / to set the hour
and then press CLOCK to
shift to minute digits.
3.
Press / to set the minute.
4. Press CLOCK to save settings
or to quit setting.
• When system is
ON, you can press
CLOCK to display
the current time for
about 2 seconds.
• When the system is OFF
(standby), the display will
turn off to save power.
minute digits.
3. Press
/ to set the
minute.
4. Press TIMER to change to OF
(timer off time) with hour
fl ashing. Repeat steps 2 & 3
for timer off time setting.
5. Press TIMER to select the
source. Press / to select
among TUNER and CD.
6. Press TIMER to set the
volume. Adjust the volume
on the main unit or press
VOL +/– on the remote
control to select the desired
volume level.
7. Press TIMER to save settings
or to quit setting.
Activating the timer
Press and release TIMER to turn
on/off the timer. The timer is
active when the clock icon is
lit.
Setting the timer
1. Press and hold TIMER until
ON (timer on time) appears
with the hour fl ashing.
2. For setting time, press
/
to set the hour and then
press TIMER to shift to the
Bass boost
Press BASS to turn on/off
boosting the bass frequency. The
BASS icon lights on the display
when it is activated.
Muting audio
Press on the remote control
to cut or restore the sound.
Using preset equalizer curves
Press EQ on the unit to select
among FLAT, ROCK, POP, JAZZ,
CLASSIC and CUSTOM. The display
shows your selection briefly.
Creating a Custom Curve
1. Press EQ on the unit to
select the CUSTOM mode.
2. While CUSTOM is displayed,
press
/ to cycle among
the displayed BASS and TREB
range levels.
3. While BASS or TREB is
displayed, adjust the volume
to set the associated gain
between -10 - +10.
4. Press EQ to exit.
Sound features
The remote control
must be inserted with
2 “AAA” or “R3” or
“UM4” batteries prior to use.
INFO – To select among disc
display information.
FM ST. – To switch between FM
stereo and mono modes.
DISC SKIP – To skip to next CD.
VOL+ / VOL– – To increase/
decrease the volume.
– To play and pause the
CD/iPod playback.
PREV/
,NEXT/ – To tune
radio frequency; to skip CD/iPod
track; to fast search through the
CD/iPod.
OPEN/CLOSE – To open and
close CD disc tray.
STOP – To stop playing CD/iPod.
PLAY MODE – To cycle between
different CD play mode.
– To mute and restore audio
output.
SHUFFLE – To turn on/off
random CD playback.
MENU – To display iPod menu;
and return to previous menu.
SELECT – To confirm iPod menu
lists.
INTRO – To turn INTRO mode
on or off to play the first 10
seconds of each CD track.
FOLDER/PRESET – To select
previous / next tuner preset
station; previous / next folder
during mp3/WMA CD playback;
and navigate the iPod menu
lists.
SLEEP – To select the time
interval in minutes before the
unit turns off.
General controls
Push Speaker
terminal tab
down to insert
wire.
Release tab to
lock wire in
the terminal.
NOTE: Make sure the insulation
is completely removed from the
ends of the speaker wires at all
connection points.
1
2
3
SOURCE
CD
TUNER
iPod
LINE IN/
AUX
I
NF
O
F
M
S
T
.
VOL
VOL
V
E
R
P
T
X
E
N
PLAY MODE SHUFFLE
SELECT
DISC SKIP
MENU
SLEEP
INTRO
RS 2767i
OPEN/CLOSE STOP
FOLDER
/PRESET
TIMER
CLOCK
FOLDER
PRESET
TUNE
TUNE
FOLDER
PRESET
O
N
/
S
T
A
N
D
B
Y
SLEEP
DEMO
DIMMER
DISCSKIP
BAND
AUTO
PROG
SOURCE
PROGRAM
PLAYMODE
L
R
LINEIN
AUXIN
SHUFFLE
EQ
TIMER
CLOCK
FOLDER
PRESET
TUNE
TUNE
FOLDER
PRESET
O
N
/
S
T
A
N
D
B
Y
SLEEP
DEMO
DIMMER
DISCSKIP
BAND
AUTO
PROG
SOURCE
PROGRAM
PLAYMODE
L
R
LINEIN
AUXIN
SHUFFLE
EQ
Radio bands
BASS – bass boost activated
File format
STEREO – FM stereo mode activated
EQ – preset equalizer activated
PROG – program playback
mode activated
SLEEP – sleep mode activated
Playback
mode
status
Folder navigation mode
Timer activated
Sleep mode
You can select the time interval
in minutes before the unit turns
off automatically.
1. Press SLEEP to select among
OFF, 120, 90, 60, 45, 30, 15, 10
and 5 minutes. The sleep icon
lights on the display when
sleep mode is activated.
2. When sleep is activated,
press SLEEP once to view
remaining sleep time.
Press SLEEP again when
the remaining sleep time
is displayed to change the
sleep time.
• Sleep is automatically de-
activated when the unit is
turned off.
Limited warranty
This unit is compatible
with CD-RW/ CD-R discs
for playback.
Notes on CD-R/RW Disc:
• Do not affi x any type
of labels to either side
(recordable or labeled
side) of a CD-R/RW disc as
this may result in the unit
malfunctioning.
• To avoid damages to the
CD-R/RW disc, do not open
the disc compartment door
while the disc is being read.
• Do not load an unrecorded
CD-R/RW disc into the unit.
This may take a longer time
to read the disc.
• Playback capability for CD-
RW discs may vary due to
variations in the quality of
the CD-RW disc and the
recorder used to create the
disc.
Notes on Simple mp3/WMA
Playback:
• This unit is compatible with
simple mp3/WMA discs. Text
information can be shown
(e.g. ID3 tags)
• It is strongly recommended
that you use a single
folder structure for simple
mp3/WMA discs. If there
are more than only layer of
folders, the tracks may be
rearranged.
• The fi rst 100 folders from
the fi rst 8 folder levels can
be read on this unit.
• The unit reads the fi rst 412
fi les from each discs and the
fi rst 255 fi les in each folder.
CD playback
Loading discs
1. Press SOURCE repeatedly to
select CD mode.
2. Press OPEN/CLOSE or to
open the drawer.
3. Insert up to fi ve discs with
label face up. (Press DISC
SKIP to rotate the disc
carrier.)
4. Press OPEN/CLOSE or
to
close the drawer. Loaded
disc position icon lights.
Selecting discs
Press DISC SKIP to skip discs.
Selecting folders (mp3/
WMA CDs only)
In stop mode,
• Press
FOLDER/PRESET to
go to the previous folder.
• Press FOLDER/PRESET to
go to the next folder.
The folder number (TF) shows
briefly then the total number of
tracks (TT) is displayed.
Playing discs
• Press to begin or pause
playback, and STOP / to
stop playback.
• Press
/ to select a
specifi c track.
Searching through a CD
Press and hold / to search
through a CD while it is playing.
Shuffl ing play order
Press SHUFFLE to turn on/off
the playing of tracks in random
order.
Sampling tracks
Press INTRO to play the first 10
seconds of each track on the
current disc, all discs in the tray,
or turn INTRO mode off.
Play mode
Press PLAY MODE to cycle
between 1 Disc, All Discs,
Repeat 1, Repeat 1 Disc, and
Repeat All Discs.
You can program the CD player
to play up to any 32 tracks on
the CDs in the tray.
1. While the CD player is
stopped, press PROGRAM
to enter program mode.
The system displays the next
available program number: “-
- P:01,” with “- -” fl ashing,
prompts you for the fi rst
track in the program list.
2. Press / to select a track
(press DISC SKIP to select a
track from a different disc).
3. Immediately press
PROGRAM to assign
the selected track to the
program number. You are
prompted for the next track
in the program list. (In CD
program mode, PROG icon
will be lit.)
Playing a program List
While in PROGRAM mode, press
.
Displaying the program List
1. While the CD player is
stopped, press PROGRAM to
enter PROGRAM mode.
2. Press PROGRAM repeatedly
to list each track assignment
in the program list.
Deleting program List
While in PROGRAM mode, press
and hold STOP / for 3 seconds.
They unit displays the message
“CLEAR”.
CD program
Only the first 99 tracks
from each disc can be
programmed.
• Refer to the diagram below for playback sequence details on
multi-level folder structure.
• Songs are played before playing songs placed in folders at each
level.
• Folder playback sequence is indicated by the letters A to G.
• Song playback sequence is indicated by the numbers (1 to 15) in
front of the song name.
mp3/WMA playback sequence
Radio
Press SOURCE or TUNER on the
remote control to select TUNER.
Selecting tuner band
Press AUTO PROG•BAND
or press and hold TUNER on
the remote control to select
between AM and FM radio
bands.
Tuning to a station
Press / to select
frequencies. Press and hold to
start auto searching for the
next available station.
Preset and tune modes
The tuner can be in either
TUNE or PRESET mode. When in
PRESET mode, the PROG light is
on.
Presetting stations
Manually setting presets
1. Press / to access the
desired frequency.
2. Press PROGRAM button.
Additional information
Disconnect the audio system
from the power source before
performing any maintenance.
Cleaning
Clean the exterior of the system
using a soft dust cloth.
CD Player
CAUTION! This system operates
with a laser. It must be opened
by only a qualified technician.
Handling CDs
• Do not touch the signal
surfaces. Hold CDs by the
edges, or by one edge
and the hole. Do not affi x
labels or adhesive tapes to
the label surfaces. Do not
scratch or damage the label.
CDs rotate at high speeds
inside the player. Do not
use damaged (cracked or
warped) CDs
Cleaning CDs
• Dirty CDs can cause poor
sound quality. Always keep
CDs clean by wiping them
gently with a soft cloth
from the inner edge toward
the outer perimeter.
•
If a CD becomes dirty, wet a
soft cloth in water, wring it
out well, wipe the dirt away
gently, and then remove any
water drops with a dry cloth.
• Do not use record cleaning
sprays or antistatic agents
on CDs. Also, never clean
CDs with benzene, thinner,
or other volatile solvents
which may cause damage to
disc surface
CD Lens Care
When your CD lens gets dirty
it can also cause the system to
output poor sound quality. To
clean the lens you will need
to purchase a CD lens cleaner
which can maintain the output
sound quality of your system.
For instructions on cleaning
the CD lens, refer to the ones
accompanying the lens cleaner.
Troubleshooting tips
Technical specifi cations
Power supply: 120V~60Hz
Dimensions ( H x W x D inches):
Unit size - 12 x 11 x 17
Main Speaker - 12.1 x 9.5 x 9
Main unit weight: 13.6 lbs
CD player: Response curve (+/-
2dB): 60Hz to 15 kHz
Rating Plate: Look for it at the
back of the set.
The descriptions and
characteristics given in this
document are given as a
general indication and not as a
guarantee. In order to provide
the highest quality product
possible, we reserve the right
to make any improvement or
modification without prior
notice. The English version
serves as the final reference on
all products and operational
details should any discrepancies
arise in other languages.
System will not turn on
• Check power cord for a
secure connection.
• Unplug the unit for a
moment, and then plug into
power source again.
• Check the outlet by plugging
in another device.
No sound
• Increase the volume setting.
• Check connection to
speakers.
•
Check that you have selected
the appropriate function: CD,
TUNER, iPod, LINE IN/AUX.
• Make sure mute is off.
• Make sure headphones are
not plugged in.
Poor radio reception
• Check antenna connection.
• Move antenna.
• Turn off nearby electrical
appliances, such as hair
dryer, vacuum cleaner,
microwave, fl uorescent
lights.
CD does not play
• Check that CD is in the tray.
• Check that CD label is facing
up.
• Check that PAUSE mode is
not on.
• Check that CD function is
selected.
• Use CD lens cleaner.
• Clean the disc.
• Try another CD.
CD sound skips
• Clean the disc.
• Check disc for warping,
scratches, or other damage.
• Check if something is causing
the system to vibrate. If so,
move the system.
• Make sure the speakers are
at least 3 feet away or on a
different surface from the
main unit.
CD button will not respond,
or does not change discs
when you press DISC SKIP
• Switch to another function
(TUNER, iPod, LINE IN/AUX)
and then back to CD.
Remote control does not work
• Check that the batteries are
properly installed.
• Replace weak batteries.
• Check the system is plugged
into power source.
• Point the remote directly at
the system’s front panel.
• Move closer to the system.
• Remove any obstacles
between the remote and the
system.
iPod does not respond to
the speaker system
• Remove your iPod from
the dock and check
for obstruction on the
connectors in the dock and
on your iPod.
• Make sure that your iPod
is working properly before
docking into the unit. Please
refer to your iPod manual
for details.
AVC MULTIMEDIA (“AVC”) makes the following limited warranty.
This limited warranty extend to the original consumer
purchaser and is limited to non-commercial use of the product.
One Year Parts & Labor Warranty
AVC products purchased in the United States are warranted to be
free from defects in materials or workmanship for a period of one
year from the date of their original retail purchase. If the unit fails
to conform to this warranty, we will service the product using new or
refurbished parts and products, at AVC’s sole discretion.
During a period of one year from the effective warranty date, AVC
will provide, when needed, service labor to repair a manufacturing
defect at its designated Service Center. To obtain warranty service
in the Untied States, you must first call our Customer Support
Center at 1-866-444-6478 or 1-800-252-6123, during the hours
listed in the box on the right. The determination of service will
be made by AVC Customer Support. PLEASE DO NOT RETURN
YOUR UNIT TO AVC WITHOUT PRIOR AUTHORIZATION. New or
remanufactured replacements for defective parts or products will be
used for repairs by AVC at its designated Service Center for one year
from the effective warranty date. Such replacement parts or products
are warranted for an additional one year from the date of repair or
replacement. The Customer will be required to ship the unit to the
Service Center indicated at the time Customer Support is contacted
to make the necessary repairs. The customer is responsible for all
transportation charges to the service facility.
Packaging and Shipping Instruction
When you send the product to the AVC service facility you must use the
original carton box and packing material or an equivalent as designated
by AVC.
LIMITED WARRANTY
Your Responsibility
1) You must retain the original sale receipt to provide proof of
purchase.
2) These warranties are effective only if the product is purchased
and operated in the U.S.A. or Canada.
3) Warranties extend only to defects in material or workmanship,
and do not extend to any product or parts which have been lost
or discarded, or damage to product or parts caused by misuse,
accident, improper operation or maintenance, or use in violation
of instructions provided with the product, or to product which
has been altered or modifi ed without authorization of AVC, or
to products or parts thereof which have had the serial number
removed or changed.
Out of Warranty
Please take care
when loading or
unloading discs in the
disc drawer. Read below for
details.
• Remove all discs from the
disc drawer before moving
or transporting the unit.
• Do not put discs in the
trays of the disc drawer
when they are still
moving.
• Do not push or force the
rotation of the disc trays.
Always use the DISC SKIP
button.
• Do not put discs in any
unexposed disc trays.
• When an error occurs and
the disc drawer does not
close, empty all disc trays
and try again.
CD-R / RW
Folder 1
Folder 3
Song 1.1.1
Song 1.1.2
Song 1.1.3
Song 2.2
Song 2.3
Song 2.4
Song 1.2.1.1
Song 1.2.1.2
Song 1.2.1.3
Folder 1.2.1
Song 2.1.1
Song 2.1.2
Folder 2.1
Song 3.1
Song 3.2
Folder 1.1
Folder 1.2
Folder 2
A
E
G
B
C
F
D
3
4
5
6
7
8
9
10
11
12
13
LEVEL 1 LEVEL 2 LEVEL 3 LEVEL 4
Song 4
Song 5
1
2
14
15
Important:
Also keep your "Bill of Sale" as proof of purchase.
Model no. ..............................................................................
Product name ...................................................................................
Type of set .................................................................................
Serial no. ..................................................................................
Invoice no. ........................................................................
Date purchased ..........................................................................
Dealer name ..........................................................................
FOR SERVICE AND REPAIR, PLEASE VISIT
www.1800customersupport.com/RCA
Specifications and external appearance are subject to change
without notice.
In the event your product requires repair after the limited
warranty period has expired, please contact our Customer
Support Center at 1-866-444-6478, 1-800-252-6123 or
www.1800customersupport.com/RCA
Hours: Monday–Thursday: 9am–7pm, Friday: 9am–5pm,
Saturday: 9am–NOON Eastern time.
Important:
You are responsible for any transportation, shipping or insurance
relative to the return of product to our Product Returns Center.
The most recently accessed
program location will be
displayed.
3. If a different program
location is preferred, press
/ to select to the
desired preset number (1-32).
4. Press PROGRAM store the
selected frequency at that
preset.
Auto preset programming
(FM only)
Press and hold AUTO PROG•
BAND for 2 seconds to scan
stations in the FM band. The
stations will then be stored as
preset channels. A maximum of
32 stations can be stored.
Beware of your preset channels
being erased accidentally
because the scanning and
storing process is automatic
upon pressing and hold the
button.
You can stop the automatic
scan by pressing any button,
but the erased stations cannot
be recovered.
Using presets
Press FOLDER/PRESET to
access the previous or next
preset station. The display
first shows the preset program
number and after a few
seconds, the frequency will be
displayed. (e.g. P:01 is preset 1)
Suppressing stereo
signal
Press FM ST. to select between
FM mono and stereo for stereo
FM stations.
All warranties implied by state law, including the implied warranties
of merchantability and fitness for a particular purpose, are expressly
limited to the duration of the limited warranties set forth above.
With the exception of any warranties implied by state law as hereby
limited, the foregoing warranty is exclusive and in lieu of all other
warranties, guarantees, agreements and similar obligations of
manufacturer or seller with respect to the repair or replacement
of any parts. In no event shall AVC be liable for consequential or
incidental damages.
No person, agent, distributor, dealer or company is authorized to
change, modify or extend the terms of these warranties in any
manner whatsoever. The time within action must be commenced to
enforce any obligation of AVC arising under the warranty or under
any statute, or law of the United States or any state thereof, is hereby
limited to one year from the date of purchase. This limitation does
not apply to implied warranties arising under state law.
This warranty gives you specific legal rights and you may also have
other rights, which may vary, from state to state. Some states do not
allow limitation on how long an implied warranty lasts, when an
action may be brought, or the exclusion or limitation of incidental
or consequential damages, so the above provisions may not apply to
you.
For more information on other products and services, please visit our
web site at
www.1800customersupport.com/RCA
Printed in China
CD playback
iPod playback
Installing the iPod Dock
Adapter
1. Choose the iPod Dock
Adapter that fits your iPod.
Adapter no.3 – iPod mini (4GB, 6GB)
Adapter no.7 – iPod photo (40GB,
60GB); iPod with color display (60GB)
Adapter no.8 – iPod nano (2GB, 4GB)
Adapter no.9 – 5G iPod with video
(30GB); U2 iPod with video (30GB);
iPod classic 80GB
Adapter no.10 – 5G iPod with video
(60GB, 80GB); iPod classic 160GB
2. Push PUSH OPEN on the
unit to open the iPod dock.
3. Insert your iPod Dock
Adapter into the dock until
it sits firmly in place.
Removing the iPod
Dock Adapter
Remove the iPod
Dock Adapter as
illustrated.
Listening to your iPod
Insert your iPod into the
connector in the dock. Press
iPod to select iPod mode.
• Press to begin or pause
playback, and STOP/ to
stop playback.
• Press / to select a
specifi c song.
• Press and hold / to
search through a song while
it is playing.
• Press MENU to display iPod
menu, press again to return
to previous menu.
• Press
FOLDER/PRESET to
navigate iPod menu lists.
• Press SELECT to confirm
iPod menu lists.
• Your iPod will
charge automatically
(until fully charged)
once it is docked.
•
To prevent interference to
AM signal, please switch off
the iPod while using Radio.
For your safety
The AC power plug is polarized
(one blade is wider than the
other) and only fits into AC power
outlets one way. If the plug won’t
go into the outlet completely, turn
the plug over and try to insert
it the other way. If it still won’t
fit, contact a qualified electrician
to change the outlet, or use a
different one. Do not attempt
to bypass this safety feature.
CAUTION: TO PREVENT ELECTRIC
SHOCK, MATCH WIDE BLADE OF
PLUG TO WIDE SLOT, FULLY INSERT.
Technical information
Product: Audio System
Brand: RCA
Model: RS2767i
Power Supply: 120V ~ 60Hz
Power Consumption: 240 Watts
Service information
This product should be serviced
only by those specially trained in
appropriate servicing techniques.
For instructions on how to obtain
service, refer to the warranty
included in this Guide.
THE LIGHTNING FLASH AND ARROWHEAD
WITHIN THE TRIANGLE IS A WARNING
SIGN ALERTING YOU OF "DANGEROUS
VOLTAGE" INSIDE THE PRODUCT.
SEE MARKING ON BOTTOM / BACK OF PRODUCT
WARNING: TO PREVENT FIRE OR ELECTRICAL SHOCK HAZARD, DO NOT
EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF
PROCEDURES OTHER THAN THOSE SPECIFIED MAY RESULT IN HAZARDOUS
RADIATION EXPOSURE.
CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED.
REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE.
WARNING: MAINS PLUG IS USED AS DISCONNECT DEVICE AND IT SHOULD
REMAIN READILY OPERABLE DURING INTENDED USE. IN ORDER TO
DISCONNECT THE MAINS PLUG FROM MAINS COMPLETELY, THE MAINS PLUG
SHOULD BE DISCONNECTED FROM THE MAINS SOCKET OUTLET COMPLETELY.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
THE EXCLAMATION POINT WITHIN THE
TRIANGLE IS A WARNING SIGN ALERTING
YOU OF IMPORTANT INSTRUCTIONS
ACCOMPANYING THE PRODUCT.
CAUTION
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE COVER
(OR BACK). NO USERSERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
• Press INFO
repeatedly to view
elapsed track time,
track remain time and
disc remain time during
playback.
• The fi rst 99 tracks of each
disc will be played once
before any of them is
repeated.
• You may also press PLAY
MODE to select 1 disc or
all discs before activating
INTRO & SHUFFLE
functions.
• In stop mode for mp3 and
WMA CDs, press STOP /
to return to the fi rst track
of the current disc. The
total number of tracks
on the current disc is
displayed (TT).
Play external sound
through the speaker
system
Press SOURCE on the unit
repeatedily to select LINE IN or
AUX mode.
Or press LINE IN/AUX on the
remote control to change to LINE
IN mode form CD, TUNER or iPod
mode, press LINE IN/AUX again
to change to AUX mode.
LINE IN / AUX
Suggest using Ø3.5mm
LINE IN jack for mp3
player and AUX IN jacks
for auxillary equippment such
as DVD, VCR or PC.
Page is loading ...
-
1
-
2
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
in other languages
- español: RCA RS2767i Manual de usuario
