Oreck BB1000 User manual

Category
Vacuum cleaners
Type
User manual

This manual is also suitable for

U
SERS GUIDE
SIMPLY AMAZING
®
COMPACT
CANISTER
VACUUMS
•IMPORTANT•
SAVE THIS BOOKLET!
Includes:
Safety Warnings
Parts List
Operating Instructions
Maintenance
•Warranty
•Trouble Diagnosis
Accessories List
ENGLISH
series
FRANÇAIS
G
UIDE D’UTILISATION PAGE 5
ESPAÑOL
GUIA D
EL USUARIO PAGE 9
73050-01 REV B
2
BEFORE OPERATING
CLEANER, READ ALL
INSTRUCTIONS IN THIS
MANUAL CAREFULLY.
Table of Contents
Table of Contents, Safeguards,
Important Safety Instructions . . . . . . . . . . . . . . . . . . . page 5-2
Warranty, Parts List, Accessories . . . . . . . . . . . . . . . . page 5-3
Assembly, To Operate, Polarized Plug Notice,
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 5-4
Maintenance & Customer Service,
Troubleshooting Guide . . . . . . . . . . . . . . . . . . . . . . . . page 5-5
Français Guide D’utilisation . . . . . . . . . . . . . . . . . . . page 5-6
Españiol Guia Del Usuario . . . . . . . . . . . . . . . . . . . página-10
Safeguards
WARNING: Unplug cord from electrical
outlet before servicing.
IMPORTANT: Make sure filter bag is in place. Do not operate
cleaner without filter bag. Damage to motor may occur.
Be sure bag gasket is in place. If the white bag gasket is
damaged or lost, replace at once.
For best results, change disposable filter bag regularly even if
it is not completely full. An extremely dirty bag or a bag close
to full will affect the suction of the cleaner and can create
excessive motor heat that could damage the motor. A good
practice is to change filter bag every 30 days even if it is not full.
Do not pick up moist material or liquids.
Clean your vacuum cleaner with a damp (not wet) cloth in the
disposable bag cavity and the outside of canister unit.
MOTOR PROTECTION SYSTEM: If fine materials such as
soot, cement, plaster dust, copy machine powder, etc. are
picked up, the bag surface may seal and cause the motor to
shut off to avoid over-heating. If this happens, turn the switch
off and unplug the cleaner. Replace filter bag. Check and
clear any clogs in hose or accessories. After approximately
30 min. the motor will have cooled and the cleaner will be
ready to use.
Note: The cleaner must remain unplugged for 30 minutes
for motor to cool and system to reset.
ENGLISH
When using an electrical appliance, basic
precautions should always be followed,
including the following:
READ ALL INSTRUCTIONS BEFORE
USING THIS VACUUM CLEANER
WARNING
To reduce the risk of fire,
electric shock, or injury:
IMPORTANT
SAFETY INSTRUCTIONS
Do not leave appliance unattended when plugged in.
Unplug from outlet when not in use and before servicing.
Do not use outdoors or on wet surfaces.
Do not allow to be used as a toy. Close attention is
necessary when used by or near children.
Use only as described in this manual.
Do not use with damaged cord or plug. If appliance is not
working as it should, has been dropped,
damaged, left outdoors, or dropped into water, return it to
a service center or call customer service at:
US: 1-800-989-3535
Canada: 1-888-676-7325
Do not pull or carry by cord, use cord as a handle, close
door on cord, or pull cord around sharp edges or corners.
Do not run appliance over cord. Keep cord away from
heated surfaces.
Do not unplug by pulling on cord. To unplug, grasp the
plug, not the cord.
Do not handle plug or appliance with wet hands.
Do not put any object into openings. Do not use with any
opening blocked; keep free of dust, lint, hair and anything
else that may reduce air flow.
Keep hair, loose clothing, fingers and all parts of body
away from openings and moving parts.
Do not use to pick up anything that is burning or smoking,
such as cigarettes, matches, or hot ashes.
Do not use without filter bag assembly in place.
•Turn off all controls before unplugging.
Use extra care when cleaning on stairs.
Do not use to pick up flammable or combustible
liquids, such as gasoline, or use in areas where they may
be present.
SAVE THESE INSTRUCTIONS
Household Use Only
Parts List
1. Adjustable shoulder strap
2. Long, extendable, flexible hose
3. Crevice tool
4. Upholstery tool
5. Horsehair bare floor and wall tool
6. Horsehair dusting brush
7. Adjustable extension wand
8. On-board tool caddy
9. Paper filter bags
10. Tool adapter tube for fitting tools directly to vacuum when
not using hose.
HEPA filter (installed)
Scent cartridge (not shown)
Accessories
Replacement Hypo-Allergenic Filter
Bags (12 pk. with 1 Micro Filter) Part No. PKBB12DW
Replacement Micro Filter Part No. 72005-01
Replacement HEPA Filter Part No. HF1000
Replacement White Bag
Gasket Part No. 72017-02
Wire Tool Rack Part No. BBRACK
Vinyl Tool Rack Part No. CADDYBB
Fresh Air
®
Scent Cartridges
Notes of Vanilla
®
12pk. Part No. FA1PK
Spring Mullberries
®
12pk. Part No. FA2PK
Blooming Jasmine
®
12pk. Part No. FA3PK
To order new parts or accessories call:
US: 1-800-989-3535
Canada: 1-888-676-7325
3
Warranty
ORECK MANUFACTURING COMPANY: (ORECK gives you the
following limited warranty for this product only if it was originally
purchased for use, not resale, from ORECK or an ORECK
Authorized Retail Dealer.)
ORECK will repair or replace, free of charge, to the original
purchaser, any part which is found to be defective in material or
workmanship within three (3) years of the date of purchase; 10
years on housing. This limited warranty applies to normal
domestic use. Any commercial use of this product will void this
limited warranty.
Parts subject to normal wear are not covered by this limited
warranty.
This limited warranty does not apply to any part subjected to
accident, abuse, commercial use, alteration, misuse, damage
caused by fire or act of God, the use of voltages other than
indicated on the serial number plate of this product or service of
this product by other than ORECK or an ORECK Factory
Authorized Service Center.
ORECK does not authorize any person or representative to
assume or grant any other warranty obligation with the sale of
this product.
ORECK’s limited warranty is valid only if you retain proof of
purchase from ORECK or an ORECK Authorized Retail Dealer
for this product. If you purchase this product from any other
source, your purchase is “AS IS,” which means ORECK grants
you no warranty, and that you, not ORECK, assume the entire
risk of the quality and performance of this product, including the
entire cost of any necessary servicing or repairs of any defects.
ORECK’s liability for damages to you for any costs whatsoever
arising out of this statement of limited warranty shall be limited
to the amount paid for this product at the time of original
purchase, and ORECK shall not be liable for any direct, indirect,
consequential or incidental damages arising out of the use or
inability to use this product.
Some states do not allow the exclusion or limitation of incidental
or consequential damages, so the above limitation or exclusion
may not apply to you.
ALL EXPRESS AND IMPLIED WARRANTIES FOR THIS
PRODUCT, INCLUDING IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE, ARE LIMITED IN DURATION TO THE WARRANTY
PERIOD, AND NO WARRANTIES, WHETHER EXPRESS OR
IMPLIED, WILL APPLY AFTER THIS PERIOD.
Some states do not allow limitations on the duration of implied
warranties, so the above limitation may not apply to you.
This warranty gives you specific legal rights, and you may also
have other rights which vary from state to state.
ENGLISH
1
2
3
4
6
5
8
7
9
10
4
For Easy Cord Storage
fig. 12 Wrap cord around the cord wrap and cord dump located
on bottom of the canister. To release cord, twist the cord
dump.
Blower Port
fig. 13 Remove HEPA Filter cover and filter at back of machine.
Firmly insert flexible hose into exhaust port.
Maintenance
Changing the Filter Bag
fig. 14 Use only genuine ORECK XL filter bags. Stand unit on
its back. Twist knob counterclockwise to release and lift
out front plate.
fig. 15 Remove used bag and insert fresh bag. The cardboard
rim fits smoothly into the recessed top. Align tabs on
front plate with slots in housing and replace the front
plate. Close unit by turning knob clockwise.
fig. 16 IMPORTANT: The white bag gasket glued in the housing
must be in place or unit will not operate properly.
Replace if needed.
NOTE: The disposable inner filter bag must be replaced once a
month even if it is not full. Change it more often if it is
used in extremely dirty areas. Increase the cleaning
power of your vacuum by changing the bag often.
Replacing the Micro Filter
Remove filter bag by following the Changing the Filter Bag
instructions.
fig. 17 Remove old micro filter from bottom inside unit. Replace
with new filter.
NOTE: A replacement filter is supplied in each package of 12
ORECK XL filter bags or you may order filters separately.
Using a HEPA-Filter and Scent Cartridge
fig. 18 Remove HEPA Filter cover at back of machine by
pressing down in top slot and folding back the cover. Lift
cover to remove.
fig. 19 Insert Fresh Air™ Scent Cartridge on tab located in
center of the filter cover.
fig. 20 Place the HEPA Filter in the filter cover.
fig. 18 Replace the HEPA Filter assembly on the canister by
placing the bottom lip of the cover in the inside slot of
the canister and closing the cover until the top latch is
locked.
NOTE: It is recommended to replace the scent cartridge when
the inner filter bag is replaced.
Replace the HEPA filter every 6 months. Replace more
often if vacuum is used to pick up fine particles or in
extremely dirty areas.
Assembly
Attach Caddy and Insert Tools
fig. 1 Locate caddy clip slots at top rear corners of canister
handle. Place appliance on firm, non-slip surface or hold
in your lap. Grasp handle firmly. Place one of caddy clip
tabs inside slot on one side of handle and stretch the
other tab around handle until the opposite tab inserts in
slot.
fig. 2 Insert crevice tool, brush and fabric tool into caddy in
spaces provided.
fig. 3 Caddy will lift up 90° to allow access to the HEPA filter
cover.
Attach Shoulder Strap
fig. 4 Clamp one end of shoulder strap in front slot located at
front of handle.
fig. 5 Clamp opposite end of shoulder strap in slot at back of
handle.
fig. 6 Adjust length by pulling strap through clip.
IMPORTANT: Before using shoulder strap, pull both ends to be
sure it is secure.
Polarized Plug Notice
This product is equipped with a polarized alternating current line
plug (a plug having one blade wider than the other). This plug
will fit into the power outlet only one way. This is a safety
feature. If you are unable to insert the plug fully into the outlet,
try reversing the plug. If the plug should still fail to fit, contact an
electrician to replace the obsolete outlet. Do not defeat the
purpose of the polarized plug.
To Operate
Plug cord into electrical outlet.
Power Switch
fig. 7 Push power switch to “ON” (I) position.
Hose and Tool Installation
fig. 8 The flexible hose uses a Shurlock™ locking system that
prevents hose removal unless intended. To install hose,
align “J” slot in hose coupling with tab inside the suction
port. Insert hose in port. Twist collar clockwise to lock
hose coupling in port. Twist counterclockwise and pull to
remove hose.
fig. 9 The adjustable extension wand and cleaning tools
supplied with your Oreck XL compact vacuum lock
together with friction. T
wist and push to be sure they lock
tightly when installing. Twist and pull to remove.
fig.10 When installing tools directly to blower or suction port
without using hose, tool adapter tube must be used.
Adjustable Extension Wand
fig. 11 To adjust extension wand, press release button and pull
inner tube to desired length. Tube will lock when button
is released. To shorten length, press release button and
push inner tube.
ENGLISH
1.Not plugged in
properly
2.No electricity in
wall outlet.
3.Motor protector
tripped.
4.Needs service.
1.Filter bag is full.
2.Hose/wand tool
is clogged.
3.Air leak due to
missing or
damaged gasket.
1.Proper friction fit
not being
obtained.
Cleaner Will
Not Run
Vacuum Will
Not Pick Up
Or Has Low
Suction
Tools/Wands
Will Not Stay
Together
5
PROBLEM POSSIBLE SOURCE AREAS TO CHECK
Maintenance and Customer Service
Your ORECK COMPACT CANISTER VACUUM is a product of
precise engineering. The motor bearings are permanently
lubricated and should not be oiled. If you require additional
information or have problems with your ORECK appliance, you
may call ORECK customer service at:
US: 1-800-989-3535
Canada: 1-888-676-7325
Please specify the model number and serial/code number which
can be found on the data plate on the bottom of the vacuum.
Save your sales or purchase slip. Should your ORECK
appliance require warranty service in the U.S.A., present this slip
to the Authorized Service Center as your proof of purchase date,
or, in Canada, call customer service.
ALL OTHER SERVICING SHOULD BE DONE BY AN
ORECK AUTHORIZED SERVICE CENTER.
ENGLISH
Troubleshooting Guide
1.Be sure cleaner is
firmly plugged into
wall outlet.
2.Check electrical
source–fuse or
circuit breaker.
3.See Motor
Protection System
page 2.
4.Take to service
center or call for
nearest service
center.
1.Replace filter bag.
See “To Replace
Filter Bag,” page 4.
2.Remove
obstructions.
3.Replace gasket
See page 4.
1.Push and turn.
Whenever calling, please be sure to have your model and serial
number from data plate.
CALL CUSTOMER SERVICE HOT LINE
US: 1-800-989-3535 Canada: 1-888-676-7325
TOUT SIMPLEMENT ÉTONNANT
•IMPORTANTE•
CONSERVEZ CE FASCICULE
®
Comprend:
Avertissements de sécurité
Garantie
Nomenclature
Mode d’emploi
Entretien
Guide de dépannage
Accessoires
NOIR AVEC DES ROUES
GUIDE D’UTILISATION
FRANÇAIS
73050-01 REV B 06/01 ECN# R-6039
© 2001 Oreck Holdings, LLC. All rights reserved. All word marks, logos, product configurations, and registered trademarks are owned and used under the
authorization of Oreck Holdings, LLC.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15

Oreck BB1000 User manual

Category
Vacuum cleaners
Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages