Utilitech Dusk to Dawn Light Control UT-5403-WH User manual

Dusk to Dawn Light Control

Questions or problems? Before returning to your

retailer, refer to the troubleshooting guide in this

manual or call our technical service department at

1-800-858-8501 (English speaking only), 7:30 am to

4:30 pm, CST, Monday – Friday.

Features

Photocell automatically turns lighting on at dusk and

off at dawn.

Requirements

• The light control requires 120-volts AC.

• Some codes require installation by a qualiﬁed

electrician.

• This product is intended for use with the enclosed

gasket and with a junction box marked for use in

wet locations.

• In some applications a universal adaptor plate may

be needed (if needed for your installation). Adaptors

are available at home centers and electrical supply

stores.

Package Contents

2 Shells

Mounting Bolt

Mounting Strap

Plastic Hanger

Rubber Plug

Bulb Holders

Cover

Plate

Light

Sensor

Dusk to Dawn Light Control

Gasket

2 Wire

Connectors

6 Mounting

Screws (3 sizes)

Items Models

247594 UT-5403-BZ

247593 UT-5403-WH

2 598-1299-01

INSTALLATION

Estimated Installation Time: 30 minutes

Items needed for installation (not included):

• Phillips and ﬂathead screwdrivers

• Pliers • Wire strippers/cutters

• Safety glasses • Silicone caulk

• Ladder • Light bulbs

• Black tape

For easy installation, select an existing light operated

by a wall switch for replacement.

IMPORTANT: Avoid mounting light control in an

extremely dark area. This may cause the lights to

stay on all the time.

For best performance, mount the ﬁxture about 8 feet

(2.4 m) above the ground.

Wire the Light Control

Eave Mount Wall Mount

Mount the Light Control

IMPORTANT: For under eave installation, the

light sensor needs to face toward the changing

light source.

Avoid water damage and

electrical shock - keep bulb

holders below horizontal.

Lock Nuts

Black to Black

White to White

Gasket

1. Remove the existing light ﬁxture.

2. Install the mounting strap as shown using two

screws that ﬁt your junction box.

3. The plastic hanger can be used to hold the ﬁxture

while wiring. The small end of the plastic hanger

can be threaded through the hole in the center of

the cover plate. The small end then goes into one

of the slots on the mounting strap.

WARNING: Turn power off at the fuse or

circuit breaker.

1. Align the light control cover plate and cover plate

gasket. Secure with the mounting bolt.

2. Align the three slots in the decorative shell with the

bulb holder pins. Push the shell in and then twist

clockwise to lock. Repeat for other shell.

3. Push the Rubber Plug ﬁrmly into place.

4. If not installed on a weatherproof box or if an adap-

tor plate (not included) was used, caulk the wall

plate and mounting surface with silicone.

5. Adjust the bulb holders by loosening the lock nuts

but do not rotate the bulb holders more than 180°

from the factory setting. When screwing in the

ﬂoodlamps, do not overtighten.

Junction box ground wire to

green ground screw on ﬁxture.

4. Route the light control’s wires through the large

gasket hole.

5. Connect the junction box wires to the light control

wires. Twist together and secure with a wire con-

nector.

3598-1299-01

SPECIFICATIONS

Electrical Load ............Up to 300 Watt Maximum

Incandescent [Up to 150 Watt

maximum each bulb holder.]

Power Requirements ..120 VAC, 60 Hz

Operating Modes ........Dusk to Dawn

HeathCo LLC reserves the right to discontinue prod-

ucts and to change speciﬁcations at any time without

incurring any obligation to incorporate new features

in products previously sold.

WARNING: Risk of ﬁre. Do not aim the bulbs

at a combustible surface within 3 ft. (1 m).

TEST AND ADJUSTMENT

Turn on the circuit breaker and light switch.

Monitor light control to verify that the lights come on

at night and turn off during the day.

Adjust bulb holders as needed.

TROUBLESHOOTING GUIDE

SYMPTOM POSSIBLE CAUSE SOLUTION

Lights will not come on. 1. Light switch is turned off.

2. Floodlight is loose or burned out.

3. Fuse is blown or circuit breaker is

turned off.

4. Daylight turn-off is in effect.

5. Incorrect circuit wiring, if this is a

new installation.

1. Turn light switch on.

2. Check ﬂoodlight and replace if

burned out.

3. Replace fuse or turn circuit breaker

on.

4. Recheck after dark.

5. Verify wiring is correct.

Lights stay on continuously. Light control is mounted in a dark

location.

Relocate light control to an area that

receives more light.

Lights ﬂash on and off. 1. Light may be leaking through the

ﬂoodlamp reﬂectors.

2. Light control may be sensing shad-

ows.

1. Replace the bulbs with new high

quality PAR 38 bulbs.

2. Relocate light control to an area

away from shadows.

4 598-1299-01

TWO YEAR LIMITED WARRANTY

This is a “Limited Warranty” which gives you speciﬁc legal rights. You may also have other rights which

vary from state to state or province to province.

For a period of two years from the date of purchase, any malfunction caused by factory defective parts

or workmanship will be corrected at no charge to you.

Not Covered - Repair service, adjustment and calibration due to misuse, abuse or negligence, light

bulbs, batteries, and other expendable items are not covered by this warranty. Unauthorized service

or modiﬁcation of the product or of any furnished component will void this warranty in its entirety. This

warranty does not include reimbursement for inconvenience, installation, setup time, loss of use, unau-

thorized service, or return shipping charges.

This warranty covers only HeathCo LLC assembled products and is not extended to other equipment

and components that a customer uses in conjunction with our products.

THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED,

INCLUDING ANY WARRANTY, REPRESENTATION OR CONDITION OF MERCHANT ABILITY OR

THAT THE PRODUCTS ARE FIT FOR ANY PARTICULAR PURPOSE OR USE, AND SPECIFICALLY

IN LIEU OF ALL SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES.

REPAIR OR REPLACEMENT SHALL BE THE SOLE REMEDY OF THE CUSTOMER AND THERE SHALL

BE NO LIABILITY ON THE PART OF HEATHCO LLC FOR ANY SPECIAL, INDIRECT, INCIDENTAL,

OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED TO ANY LOSS OF BUSINESS OR

PROFITS, WHETHER OR NOT FORESEEABLE. Some states or provinces do not allow the exclusion

or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply

to you. Please keep your dated sales receipt, it is required for all warranty requests.

TECHNICAL SERVICE

Please call 1-800-858-8501 (English speaking only) for assistance before return-

ing product to store.

If you experience a problem, follow this guide. You may also want to visit our Web site at: www.hzsupport.

com. If the problem persists, call* for assistance at 1-800-858-8501 (English speaking only), 7:30 AM to 4:30

PM CST (M-F). You may also write* to:

HeathCo LLC

P.O. Box 90004, Bowling Green, KY 42102-9004

ATTN: Technical Service

* If contacting Technical Service, please have the following information available: Model Number, Date of

Purchase, and Place of Purchase.

No Service Parts Available for this Product

Page is loading ...

Utilitech Dusk to Dawn Light Control UT-5403-WH User manual

This manual is also suitable for

Utilitech Dusk to Dawn Light Control UT-5403-WH User manual

in other languages

Related papers

Other documents