Marantec Digital 309 Owner's manual

Brand: Marantec

Model: Digital 309

Type: Owner's manual

Digital 309

Multi-channel transmitter for impulse

control

Versions

Digital 309 868 MHz (Art.-Nr. 70 466)

Digital 309 433 MHz (Art.-Nr. 71 671)

Safety advice

Attention:

• Please read these instructions carefully

before connecting and using this unit!

• When operating doors or other devices

with this unit please always make sure

that there are neither persons nor objects

in the operating range!

• Check regularly whether the unit is ready

for transmission!

• Have faulty devices checked by the manu

facturer.

• Do not carry out changes to the unit in an

unauthorized way.

Operation / transmitter

• When you push one of the four priority channel

buttons or a sequence of the channel buttons and

then you push one of the ENTER buttons, a

command is transmitted.

• After you have released the buttons, the

transmitter is still active for approx. 18 seconds, so

that a transmission is still possible when you push

one of the ENTER buttons again.

Advice:

Please enter your channel number within 10

seconds.

• You have the possibility to save up to 999 codes.

• The priority channel buttons and the channel

buttons are already coded by factory.

• When you enter more than 3 digits, the last three

digits are saved in each case.

• The transmitter transmits as long as a button is

pushed, but after 36 seconds it cuts automatically.

Learning

• Transmit the code of the multi-channel transmitter

to the RC remote control (see installation

instructions of the RC remote control of the unit

to be operated).

• The selection of channel is carried out by pushing

one of the four priority channel buttons or a

sequence of the channel buttons (enter max. 3

digits) and then by pushing one of the ENTER

buttons.

Coding modes

Learning:

Single button codes may be learned by already

existing transmitters and single codes of the

multi-channel transmitter can be transferred to other

transmitters.

Duplicating:

The codes of all buttons may be transferred

completely from one multi-channel transmitter to

another multi-channel transmitter.

Random coding:

Single buttons or button combinations of the multi-

channel transmitter can be programmed with a new

code.

Learning - hand transmitter to multi-channel

transmitter:

1. Connect the source transmitter (hand transmitter)

and the target transmitter (multi-channel trans

mitter) by means of the programming cable.

2. Hold button 2 of the target transmitter until

LED D glows.

3. Push the middle ENTER button.

LED D flashes slowly.

4. Either enter the channel number on the target

transmitter or push a priority button that shall be

relearned. Then hold the middle ENTER button

until the learning process is terminated

(see step 5).

5. Push within 10 seconds the button on the source

transmitter the code of which shall be transferred

and hold it. LED D of the target transmitter

flashes quickly and glows for approx. 3 seconds

after the learning process is terminated. Then

release both buttons.

6. Remove the programming cable.

Learning - multi-channel transmitter to hand

transmitter

1. Connect the source transmitter (multi-channel

transmitter) and the target transmitter (hand

transmitter by means of the programming cable.

2. Either enter the channel number on the source

transmitter and hold the middle ENTER button

until the learning process is terminated (see step

3) or push the priority button on the source

transmitter the code of which shall be transferred

and hold it until the learning process is

terminated.

3. Push the channel button on the target transmitter

that shall take over the code and hold it. The LED

on the target transmitter flashes quickly and

glows after the learning process is terminated.

Release both buttons.

4. Remove the programming cable.

Learning of single codes - multi-channel trans-

mitter to multi-channel transmitter

1. Connect the source transmitter and the target

transmitter by means of the programming cable.

2. Push button 2 of the target transmitter until

LED D glows.

3. Push the middle ENTER button. The LED D flashes

slowly.

4. Either enter the channel number on the target

transmitter or push the priority button on the

target transmitter that shall be re-learned. Then

hold the middle ENTER button until the learning

process is terminated (see step 5).

5. Either enter the channel number on the source

transmitter and then hold the middle ENTER

button or push the priority button on the source

transmitter the code of which shall be transferred

and hold it. The LED on the target transmitter

flashes quickly and glows for approx. 3 seconds

after the learning process is terminated. Release

both buttons.

6. Remove the programming cable.

Cancel the learning process.

Push the left or the right ENTER button.

Duplicating

1. Connect both multi-channel transmitters by

means of the programming cable.

2. Hold button 0 on the target transmitter (approx.

5 seconds) until LED C glows.

3. Then push the middle ENTER button on the target

transmitter and hold it until the duplicating

process is terminated (see Stepp 5).

The LED C flashes slowly.

4. Push the button 0 on the source transmitter

within 10 (short press) seconds and then the

middle ENTER button. The coding is transferred

and the LED C on the target transmitter flashes

quickly for approx. 70 seconds. The LED C on the

source transmitter flashes slowly.

5. As soon as the LED C on the target transmitter

glows for approx. 3 seconds, the duplicating

process is terminated.

6. Remove the programming cable.

Cancel duplicating

• Push the left or right ENTER button.

Attention:

Please note that all transferred data have been

saved already in the target transmitter!

LED

A, B, C, D

Vorzugstasten

A, B, C, D

Kanaltasten

0 bis 9

ENTER-

Tasten

ENTER

Priority channel

buttons

A, B, C, D

Channel buttons

0 to 9

ENTER

buttons

LED A, B, C, D

Random coding

1. Insert the programming cable into the socket of

the multi-channel transmitter and short-circuit at

the other end of the cable one of the outer pins

with the centre pin.

2. Hold button 1 until LED B glows.

3. Push shortly on the middle ENTER button.

The LED B flashes slowly.

4. Push the priority button or enter the channel

number for which a new random code shall be

set up.

5. Hold the middle ENTER button until LED B flashes

quickly. The new channel number is now saved.

6. As soon as the LED B glows permanently, the

coding is terminated and the middle

ENTER button can be released.

Cancel random coding

• Push the left or right ENTER button.

Attention:

The new coding has to be transferred to the RC

remote control of the unit that is to be

operated.

Change of battery

1. Open the bottom of the housing.

2. Remove the old batteries.

3. Insert two new 3 V batteries (type: CR2032).

Test the function. Observe right poling!

4. Close the bottom of the housing again.

Advice:

When changing the battery the saved data

remain unchanged.

Advice:

Do not dispose of old batteries in garbage!

Return them to the special trade or in a

recycling bin for old batteries.

Trouble shooting

• In case the LEDs glow weakly:

change the batteries.

• In case the LEDs do not glow:

check the poling of the batteries.

• In case the receiver does not react all the same:

reduce the distance to the RC remote control or

transfer the channels of the multi-channel

transmitter to the RC remote control(s) again.

Cleaning

Carefully wipe the housing with a damp and lint-

free cloth.

Attention:

Do not use cleansing agents containing solvents.

These are hazardous for your health and will destroy

the surface of the housing.

Technical details

Frequency: 868 MHz or 433 MHz

Power supply: 2 batteries 3V, CR 2032

Power consumption: approx. 15 mA

Protection category: IP 54

Range of temperature: -20°C to 60°C

Correct use

The multi-channel transmitter has been developed

to operate radio-controlled devices.

The manufacturer is not liable for damages that

occur due to incorrect or faulty use!

This product fulfils the essential requirements of the

R&TTE directive 1995/5/EG.

The Declaration of Conformity can be looked up at

the manufacturer mentioned in the supply

documents.

868 MHz

All European countries except:

BA / BG / YU / LV / RO / RU / SK / SI / UA / BY

433 MHz

All European countries except:

BA / YU / LT / RU / SI / UA / BY

Version: 05.2006

#73 158

1 - GB 360242 - M - 0.5 - 0105



ENTER

Marantec Digital 309 Owner's manual

Marantec Digital 309 Owner's manual

Marantec Digital 309 Owner's manual

Related papers

Other documents