Zanussi ZWD76NB4PW User manual

Brand: Zanussi

Model: ZWD76NB4PW

Category: Tumble dryers

Type: User manual

GETTING

STARTED?

EASY.

User Manual

ZWD76NB4PW

EN User Manual

Washer Dryer

VISIT OUR WEBSITE TO:

Get usage advice, brochures, trouble shooter, service and repair information:

www.zanussi.com/support

SAFETY INFORMATION

Before the installation and use of the appliance, carefully read the

supplied instructions. The manufacturer is not responsible for any

injuries or damage that are the result of incorrect installation or

usage. Always keep the instructions in a safe and accessible

location for future reference.

CHILDREN AND VULNERABLE PEOPLE SAFETY

WARNING!

Risk of suffocation, injury or permanent disability.

• This appliance can be used by children aged from 8 years and

above and persons with reduced physical, sensory or mental

capabilities or lack of experience and knowledge if they have

been given supervision or instruction concerning the use of the

appliance in a safe way and understand the hazards involved.

• Children between 3 and 8 years of age and persons with very

extensive and complex disabilities shall be kept away from the

appliance unless continuously supervised.

• Children of less than 3 years of age should be kept away from

the appliance unless continuously supervised.

• Do not let children play with the appliance.

• Keep all packaging away from children and dispose of it

appropriately.

• Keep detergents away from children.

• Keep children and pets away from the appliance when the door

is open.

• If the appliance has a child safety device, it should be activated.

• Children shall not carry out cleaning and user maintenance of

the appliance without supervision.

GENERAL SAFETY

• Do not change the speciﬁcation of this appliance.

• This appliance is intended to be used in household and similar

applications such as:

– staff kitchen areas in shops, ofﬁces and other working

environments;

– by clients in hotels, motels, bed & breakfast and other

residential type environments;

– areas for communal use in blocks of ﬂats or in launderettes.

• The appliance shall be installed as a freestanding product or

below the kitchen worktop if space margins permit.

• Do not install the appliance behind a lockable door, a sliding

door or a door with a hinge on the opposite side, that would

prevent the appliance door from being fully open.

• Connect the mains plug to the mains socket only at the end of

the installation process. Make sure that the mains plug is

accessible after installation.

• The ventilation opening in the base must not be covered by a

carpet, mat, or any ﬂoor covering.

• CAUTION: The appliance must not be supplied through an

external switching device, such as a timer, or connected to a

circuit that is regularly switched on and off by a utility.

• Ensure good air ventilation in the room where the appliance is

installed to avoid the backﬂow of unwanted gases into the room

from appliances burning gas or other fuels, including open ﬁres.

• Exhaust air must not be discharged into a ﬂue which is used for

exhausting fumes from any appliances burning gas or other

fuels.

• The operating water pressure at the water entry point from the

outlet connection must be between 0.5 bar (0.05 MPa) and 8

bar (0.8 MPa).

• Do not exceed the maximum load of 7 kg (refer to the

"Programme chart" chapter).

• The appliance must be connected to the water mains using the

new supplied hose sets, or other new hose sets supplied by

the Authorised Service Centre.

• Old hose sets must not be reused.

• If the mains power supply cable is damaged, it must be

replaced by the manufacturer, its Authorised Service Centre or

similarly qualiﬁed persons to avoid an electrical hazard.

• Wipe away lint or packaging debris that has accumulated

around the appliance.

• Items that have been soiled with substances such as vegetable

or mineral oil, acetone, alcohol, petrol, kerosene, spot removers,

turpentine, waxes and wax removers should be washed

separately with an extra amount of detergent before being dried

in the washer dryer.

• Do not use the appliance if items have been soiled with

industrial chemicals.

• Do not dry unwashed items in the wash dryer.

• Items such as foam rubber (latex foam), shower caps,

waterproof textiles, and rubber backed articles and clothes, or

pillows ﬁtted with foam rubber pads should not be dried in the

washer dryer.

• Fabric softeners, or similar products, should only be used as

speciﬁed by the product manufacturer’s instructions.

• Remove all objects from items that could be a source of ﬁre

ignition such as lighters or matches.

• Never stop the washer dryer before the end of the drying cycle

unless all items are quickly removed and separated so that

residual heat can dissipate.

• The ﬁnal part of the washer dryer cycle takes place without heat

(cool down cycle) to ensure that items reach a temperature that

will not cause damage to them.

• Do not use high pressure water sprays and/or steam to clean

the appliance.

• Clean the appliance with a moist cloth. Use only neutral

detergents. Do not use abrasive products, abrasive cleaning

pads, solvents or metal objects.

• Before any maintenance operation, deactivate the appliance

and disconnect the mains plug from the socket.

SAFETY INSTRUCTIONS

INSTALLATION

The installation must comply with

relevant national regulations.

• Follow the installation instructions supplied with

the appliance.

• Do not install or use the appliance where the

temperature can be less than 0°C or where it is

exposed to the weather.

• Always keep the appliance vertical when it is

being moved.

• Make sure that there is air circulation between

the appliance and the ﬂoor.

• Remove all the packaging and the transit bolts.

• The ﬂoor area on which the appliance is to be

installed must be ﬂat, stable, heat resistant and

clean.

• Keep the transit bolts in a safe place. If the

appliance is to be moved in the future they must

be reattached to lock the drum to prevent an

internal damage.

• Always take care when moving the appliance as

it is heavy. Always use safety gloves and

enclosed footwear.

• Do not install or use a damaged appliance.

• Do not install the appliance where the appliance

door cannot be fully opened.

• Adjust the feet to have the necessary space

between the appliance and the ﬂooring.

• When the appliance is in its permanent position,

check if it is levelled correctly with the aid of a

spirit level. If it is not, adjust the feet accordingly.

ELECTRICAL CONNECTION

WARNING! Risk of ﬁre and electric

shock.

• The appliance must be earthed.

• Always use a correctly installed shockproof

socket.

• Do not use multi-plug adapters and extension

cables.

• Do not pull the mains cable to disconnect the

appliance. Always pull the mains plug.

• Do not touch the mains cable or the mains plug

with wet hands.

• This appliance is ﬁtted with a 13 A mains plug. If

it is necessary to change the mains plug fuse,

use only a 13 A ASTA (BS 1362) fuse (UK and

Ireland only).

WATER CONNECTION

• Do not cause damage to the water hoses.

• Before connection to new pipes, pipes not used

for a long time, where repair work has been

carried out or new devices ﬁtted (water meters,

etc.), let the water ﬂow until it is clean and clear.

• Ensure that there are no visible water leaks

during and after the ﬁrst use of the appliance.

USE

WARNING! Risk of injury, electric

shock, ﬁre, burns or damage to the

appliance.

• Do not put ﬂammable products or items that are

wet with ﬂammable products in, near or on the

appliance.

• Do not touch the glass door while a programme

operates. The glass can get hot.

• Do not dry damaged (torn, frayed) items that

contain padding or ﬁllings.

• If laundry has been washed with a stain remover,

carry out an additional rinse cycle before

starting a drying cycle.

• Make sure that all metal objects are removed

from the laundry.

• Dry only fabrics that are suitable to dry in the

appliance. Follow the cleaning instruction on the

item label.

• Do not sit or stand on the open door of the

appliance.

• Do not dry dripping wet clothes in the

appliance.

• Do not let hot items to touch the plastic parts of

the appliance.

• Remove a detergent ball (if used) before

starting a drying programme.

• Do not use a detergent ball if setting a non-stop

programme.

INTERNAL LIGHTING

WARNING! Risk of injury.

• Concerning the lamp(s) inside this product and

spare part lamps sold separately: These lamps

are intended to withstand extreme physical

conditions in household appliances, such as

temperature, vibration, humidity, or are intended

to signal information about the operational

status of the appliance. They are not intended to

be used in other applications and are not

suitable for household room illumination.

• To replace the internal lighting, contact the

Authorised Service Centre.

SERVICE

• To repair the appliance contact the Authorised

Service Centre. Use original spare parts only.

• Please note that self-repair or non-professional

repair can have safety consequences and might

void the guarantee.

• The following spare parts will be available for 10

years after the model has been discontinued:

motor and motor brushes, transmission between

motor and drum, pumps, shock absorbers and

springs, washing drum, drum spider and related

ball bearings, heaters and heating elements,

including heat pumps, piping and related

equipment including hoses, valves, ﬁlters and

aquastops, printed circuit boards, electronic

displays, pressure switches, thermostats and

sensors, software and ﬁrmware including reset

software, door, door hinge and seals, other

seals, door locking assembly, plastic peripherals

such as detergent dispensers. Please note that

some of these spare parts are only available to

professional repairers, and that not all spare

parts are relevant for all models.

DISPOSAL

• Disconnect the appliance from the mains

electrical and water supplies.

• Cut off the mains electrical cable close to the

appliance and dispose of it.

• Remove the door catch to prevent children or

pets from becoming trapped in the drum.

• Dispose of the appliance in accordance with

local requirements for the disposal of Waste

Electrical and Electronic Equipment (WEEE).

PRODUCT DESCRIPTION

APPLIANCE OVERVIEW

1 2 3

Worktop

Detergent dispenser

Control panel

Door handle

Rating plate

Quick Reminder sticker

Drain pump ﬁlter

Feet for levelling the appliance

00000000

00A

Mod.

xxxxxxxxx

000V ~ 00Hz 0000 W

910000000

Prod.No.

The rating plate reports the model name (A),

product number (B), electrical ratings (C) and

serial number (D).

TECHNICAL DATA

Dimension Width/ Height/ Total depth 59.7 cm /84.7 cm /55.7 cm

Electrical connection Voltage

Overall power

Fuse

Frequency

230-240 V

2200 W

13 A

50 Hz

Level of protection against ingress of solid particles and

moisture ensured by the protective cover, except where

the low voltage equipment has no protection against

moisture

IPX4

Water supply

1) Cold water

Water supply pressure

Minimum

Maximum

0.5 bar (0.05 MPa)

8 bar (0.8 MPa)

Maximum wash load Cotton 7 kg

Maximum dry load Cotton

Synthetics

4 kg

3 kg

Spin Speed Maximum spin speed 1551 rpm

1) Connect the water inlet hose to a water tap with a 3/4'' thread.

2) The appliance works correctly if the water pressure is not lower than 0.05 MPa (0.5 bar). If you cannot

connect the water inlet hose to the cold water tap of the primary hydraulic system, connect it to your do-

mestic cold water storage system. Make sure not to exceed a distance of 5.02 m (16.5 ft) between the

appliance inlet hose and the bottom of the water storage tank.

INSTALLATION

WARNING! Refer to Safety chapters.

UNPACKING

WARNING! Remove all the packaging

and the transit bolts before installing

the appliance.

1. Use the gloves. Remove the external ﬁlm. If

necessary, use a cutter.

2. Remove the cardboard top. Remove the

polystyrene packaging materials.

3. Remove the internal ﬁlm.

4. Open the door. Remove the polystyrene piece

from the door seal and all the items from the

drum.

5. Put one of the polystyrene packaging elements

on the ﬂoor behind the appliance. Carefully put

down the appliance with the rear side on it.

Make sure not to damage the hoses.

6. Remove the polystyrene protection from the

bottom. Pull up the appliance in vertical

position.

7. Remove the power supply cable and the drain

hose from the hose holders.

8. Remove the three bolts. Use the key supplied

with the appliance. Pull out the plastic spacers.

9. Put the plastic caps in the holes. You can ﬁnd

these caps in the user manual bag.

We recommend that you keep the

packaging and the transit bolts for any

movements of the appliance.

INFORMATION FOR INSTALLATION

Positioning and levelling

Adjust the appliance correctly to prevent vibration,

noise and movement of the appliance when it

operates.

1. Install the appliance on a ﬂat hard ﬂoor. The

appliance must be levelled and stable. Make sure

that the appliance does not touch the wall or other

units and there is air circulation below the

appliance.

2. Loosen or tighten the feet to adjust the level. All

feet must rest ﬁrmly on the ﬂoor.

WARNING! Do not put cardboard,

wood or equivalent materials below

the appliance feet to adjust the level.

The inlet hose

CAUTION! Make sure there is no

damage to hoses and there are no

leaks from the couplings. Do not use

an extension hose if the inlet hose is

too short. Contact the service centre

for a replacement inlet hose.

1. Connect the water inlet hose to the back of the

appliance.

20º20º

45º45º

2. Position it toward left or right depending on the

positon of the water tap. Make sure that the inlet

hose is not in vertical position.

3. If necessary, loosen the ring nut to set it in the

correct position.

4. Connect the water inlet hose to the cold water

tap with 3/4'' thread.

Water drainage

The drain hose should stay at a height of no less

than 60 cm and not more than 100 cm.

You can extend the drain hose to

maximum 400 cm. Contact the

authorised service centre for the other

drain hose and the extension.

It is possible to connect the drain hose in different

ways:

1. Make a U shape with the drain hose and put it

around the plastic hose guide.

2. On the edge of a sink - Fasten the guide to the

water tap or to the wall.

Make sure that the plastic guide

cannot move when the appliance

drains and the drain hose end is not

immersed in the water. There may be a

return of dirty water into the appliance.

3. If the end of the drain hose looks like this (see

the picture), you can push it directly into the stand

pipe.

4. To a stand pipe with vent hole - Insert the drain

hose directly into a drain pipe. Refer to the

illustration.

The end of the drain hose must always

be ventilated , i.e. the inner diameter of

the drain pipe (min. 38 mm - min. 1.5")

must be larger than the external

diameter of the drain hose.

5. Without the plastic hose guide, to a sink spigot-

Put the drain hose in the spigot and tighten it with a

clamp. Refer to the illustration.

Make sure that the drain hose makes a loop to

prevent particles going into the appliance from the

sink.

ø16

W011

Connect the drain hose to the spigot and tighten it

with a clamp. Make sure that the drain hose makes

a loop to prevent particles going into the appliance

from the sink.

6. Position the hose directly to a built-in drain pipe

in the room wall and tighten it with a clamp.

INSTALLATION ON SUSPENDED FLOORING

Suspended wooden ﬂoors are particularly

susceptible to vibration.

To limit vibration we recommend placing a

waterproof wooden panel, at least 15 mm thick,

under the appliance. It should be screwed to at

least 2 ﬂoor beams and should extend beyond the

front feet.

If possible, install the appliance where the ﬂoor is

more stable.

ELECTRICAL CONNECTION

At the end of installation you can connect the mains

plug to the mains socket.

The rating plate and the 'Technical Data' chapter

indicate the necessary electrical ratings. Make sure

that they are compatible with the mains power

supply.

Check that your domestic electrical installation can

take the maximum load required, also taking into

account any other appliances in use.

Connect the appliance to an earthed socket.

The power supply cable must be easily accessible

after installing the appliance.

For any electrical work required to install this

appliance, contact our Authorised Service Centre.

The manufacturer does not accept any

responsibility for damage or injury through failure to

comply with the above safety precaution.

CONTROL PANEL

CONTROL PANEL DESCRIPTION

20°

90°

40°

30°

1000

60°

1200

1600

800

20min Wash

Delicates

CleanBoost

Cottons

Temp

Spin

Flexi

Time

Delay

Start

Time

Dry

Auto

Dry

Extra

Rinse

Prewash

Eco 40-60

Synthetics

Wool

Drain

Spin

Rinse

Cottons

Synthetics

Wool

60min

Wash&Dry

1 2 3 4

1011

Programme knob

Spin speed reduction (Spin)

Temperature selection (Temp.)

Display

Drying time selection (Time Dry)

Prewash phase (Prewash)

Additional rinse (Extra Rinse)

Automatic drying level (Auto Dry)

Start/Pause

Delay start setting (Delay Start)

Time saving (Flex Time)

DISPLAY

A B

E DFG

Time area

: Programme duration

: Selected drying time

: Delay start

: Alarm codes

: Message of error

: The programme is completed.

Time programme indicators

: Normal duration indicator

: Quick indicator

: Super quick indicator

B Delay start indicator

Child safety lock indicator

Door locked indicator

, ,

Indicators of dryness level

Drying phase indicator

Washing phase indicator

PROGRAMMES

PROGRAMME CHART

Programme

Default temperature

Temperature range

Maximum load

Reference spin

speed

Programme description

(Type of load and level of soiling)

Eco 40-60 (Wash only

mode)

40 °C

60 °C

- 30 °C

7 kg

1600 rpm

White cotton and fast-coloured cotton.

Normally soiled items.

Eco 40-60 + Cupboard

dry level (Wash & Dry

mode)

40 °C

60 °C - 30 °C

4 kg

1600 rpm

Eco 40-60 + Cupboard

dry level (Dry only mode)

4 kg

White cotton and fast-coloured cotton.

Programme

Default temperature

Temperature range

Maximum load

Reference spin

speed

Programme description

(Type of load and level of soiling)

Cottons

40 °C

90°C - (Cold)

7 kg

1600 rpm

White cotton and coloured cotton.

Normally, heavily and lightly soiled items.

Synthetics

40 °C

60°C - (Cold)

3 kg

1200 rpm

Synthetic items or mixed fabric items.

Normally soiled items.

Wool

40 °C

40°C - (Cold)

1.5 kg

1200 rpm

Machine washable wool, hand washable

wool and other fabrics with «hand washing»

care symbol

Delicates

30 °C

40°C - (Cold)

2 kg

1200 rpm

Delicate fabrics such as acrylics, viscose

and mixed fabrics requiring gentler wash-

ing. Normally and lightly soiled items.

CleanBoost

60 °C

7 kg

1600 rpm

White cotton items.

It combines a high performance wash pro-

gramme and steam vapour to remove allergens

and bacteria from your favourite garments. The

Santize Vapour programme keeps the tempera-

ture above 60° by reheating throughout the

washing phase and the vapour action on the ﬁ-

bre allows very good detergent residue removal

during rinsing.

20min Wash

30 °C

40 °C - 30 °C

3 kg

1200 rpm

A very short cycle for lightly soiled cotton

and synthetic items or worn only once.

Drain 7 kg To drain the water in the drum. All fabrics.

Spin

7 kg

1600 rpm

All fabrics, except woollens and delicate

fabrics. To spin the laundry and to drain the

water in the drum.

Rinse

7 kg

1600 rpm

To rinse and spin the laundry. All fabrics, ex-

cept woollens and very delicate fabrics. Reduce

the spin speed accordingly to the type of laun-

dry.

Wool

1 kg

Drying programme for woollens.

Synthetics

3 kg

Drying programme for synthetic items.

Cottons

4 kg

Drying programme for cotton items.

Programme

Default temperature

Temperature range

Maximum load

Reference spin

speed

Programme description

(Type of load and level of soiling)

60min Wash&Dry

30 °C

40 °C - 30 °C

1 kg

1200 rpm

Complete programme composed of a washing

phase and of a drying phase for a small load of

mixed fabrics (cotton and synthetic items).

Off position

1) According to Commission Regulation EU 2019/2023. This programme at default temperature and

spin speed, in washing only mode, with rated capacity 7 kg is able to clean normally soiled cotton laundry

declared to be washable at 40 °C or 60 °C, together in the same cycle.

For the reached temperature in the laundry, the programme duration and other data, please

refer to 'Consumption Values' chapter.

The most efﬁcient programmes in terms of energy consumption are generally those that per-

form at lower temperatures and longer duration.

2) Cottons energy saving programme. This programme at 60ºC with a load of 7 kg is the reference

programme for data entered in the energy label, in compliance with 96/60/EC Directive. Set this pro-

gramme to have a good washing results and decrease the energy consumption. The time of the washing

programme is extended.

3) According to Commission Regulation EU 2019/2023. This programme at default temperature and

spin speed, in washing and drying mode, with rated capacity 4 kg and with Cupboard dry level performs

the wash and dry cycle able to clean normally soiled cotton laundry declared to be washable at 40 °C or

60 °C, together in the same cycle and, after drying phase, the laundry can be immediately stored in a cup-

board.

4) This programme is the drying reference programme for data entered in the energy label on compliance

with 96/60/EC Directive. The test performance, in accordance with EN 50229, must be carried out with a

FIRST drying load of the maximum declared drying capacity (load composition according to EN61121) by

setting the AUTOMATIC CUPBOARD DRY for Eco 40-60 programme. The SECOND drying load with

the residual load must be tested by setting the AUTOMATIC CUPBOARD DRY for Eco 40-60 pro-

gramme.

5) During this cycle the drum rotates slowly to ensure a gentle wash. It can seem that the drum doesn't

rotate or doesn't rotate properly, but this is normal for this programme.

6) The maximum load refers to cottons items. Reduce the load accordingly in case of other type of laundry.

7) The maximum spin speed is related to cotton items. Set the spin speed. Make sure that it agrees with

the laundry.

Programme options compatibility

Programme

Spin

Flex Time

Delay Start

Eco 40-60

■ ■ ■ ■ ■

■

Cottons ■ ■ ■ ■ ■ ■ ■

Synthetics ■ ■ ■ ■ ■ ■ ■

Programme

Spin

Flex Time

Delay Start

Wool

■ ■ ■ ■

Delicates ■ ■ ■ ■ ■ ■

CleanBoost ■ ■ ■ ■ ■ ■

20min Wash ■ ■ ■

Drain ■

Spin ■ ■ ■

Rinse ■ ■ ■ ■ ■

Wool

■

Synthetics

■

Cottons

■

60min Wash&Dry ■

1) Only the QUICK option is available.

Suitable detergents for each programme

Programme

Universal

powder

Liquid

Universal

Liquid for

coloureds

Delicates

woollens

Special

Eco 40-60 ▲ ▲ ▲ -- --

Cottons ▲ ▲ ▲ -- --

Synthetics ▲ ▲ ▲ -- --

Delicates -- -- -- ▲ ▲

Wool -- -- -- ▲ ▲

20min Wash -- ▲ ▲ -- --

CleanBoost ▲ ▲ -- -- ▲

60min

Wash&Dry

-- ▲ ▲ -- --

1) At temperature higher than 60 °C the use of powder detergent is recommended.

▲ = Recommended -- = Not recommended

AUTOMATIC DRYING

Dryness Level Type of fabric Load

Extra Dry

For towelling materials

Cottons and Linen

(bathrobes, bath towels, etc)

up to 4 kg

Cupboard Dry

For items to be stored

Cottons and Linen

(bathrobes, bath towels, etc)

up to 4 kg

Synthetics and mixed fab-

rics

(jumpers, blouses, underwear,

household and bed linen)

up to 3 kg

Wool items (woollen jumpers) up to 1 kg

Iron Dry

Suitable for ironing

Cottons and Linen

(sheets, tablecloths, shirts, etc)

up to 4 kg

TIMED DRYING

Dryness Level Type of fabric Load (kg)

Spin

speed

(rpm)

Suggested

duration

(mins)

Extra Dry

For towelling materials

Cottons and Linen

(bathrobes, bath towels, etc)

4 1600 165 - 180

2 1600 90 - 100

1 1600 60 - 70

Cupboard Dry

For items to be stored

Cottons and Linen

(bathrobes, bath towels, etc)

4 1600 155 - 170

2 1600 80 - 90

1 1600 50 - 60

Cupboard Dry

For items to be stored

Synthetics and mixed fab-

rics

(jumpers, blouses, underwear,

household and bed linen)

3 1200 90 - 105

1 1200 40 - 50

Wool

(woollen jumpers)

1 1200 80 - 100

Iron Dry

Suitable for ironing

Cottons and Linen

(sheets, tablecloths, shirts, etc)

4 1600 110 - 125

2 1600 65 - 75

1 1600 40 - 50

OPTIONS

TEMP.

Set this option to change the default temperature.

Indicator = cold water.

The display shows the set temperature.

SPIN

With this option you can change the default spin

speed.

The indicator of the set speed comes on.

Additional spin options:

No Spin

• Set this option to deactivate all spin phases.

Only the drain phase is available.

• The related indicator comes on.

• Set this option for very delicate fabrics.

• The rinses phase uses more water for some

washing programmes.

Rinse Hold

• Set this option to prevent the laundry creases.

• The related indicator comes on.

• There is a water in the drum when the

programme is completed.

• The drum turns regularly to prevent the laundry

creases.

• The door stays locked. You must drain the water

to unlock the door.

To drain the water refer to ‘At the end

of the programme’.

TIME DRY

With this option you can set the time for the fabrics

you have to dry. The display shows the set value.

Each time you press this touchpad the time value

increases by 5 minutes.

You cannot set all time values for

different types of fabrics.

AUTO DRY

With this option you can set an automatic level of

dryness for the laundry. The display shows the

symbol of the set level.

•

Extra dry level for cotton items

• Cupboard dry level for cotton and synthetic

items

• Iron dry level for cotton items

PREWASH

With this option you can add a prewash phase to a

washing programme.

Use this option for heavy soil.

When you set this option the programme duration

increases.

The related indicator comes on.

EXTRA RINSE

With this option you can add extra rinses to a

washing programme.

Use this option for persons allergic to detergents

and in areas where the water is soft.

The related indicator comes on.

DELAY START

With this option you can delay the start of a

programme from 30 minutes to 20 hours.

The display shows the related indicator.

FLEX TIME

Press Flex Time to decrease the programme time.

You can select:

•

QUICK: to wash items with daily soil.

• SUPER QUICK: to wash quickly items with

almost no soil.

Some programmes accept only one of

these options.

SETTINGS

CHILD LOCK

With this option you can prevent that the children

play with the control panel.

• To activate/deactivate this option, press

and at the same time until the indicator

comes on/goes off.

You can activate this option:

• After you press

: the options and the

programme knob are locked.

• Before you press : the appliance cannot

start.

PERMANENT EXTRA RINSE

With this option you can permanently have an extra

rinse when you set a new programme.

• To activate/deactivate this option press

and at the same time until the indicator

comes on/goes off.

ACOUSTIC SIGNALS

The acoustic signals operate when:

• The programme is completed.

• The appliance has a malfunction.

To deactivate/activate the acoustic signals,

press

and at the same time for 6 seconds.

If you deactivate the acoustic signals,

they continue operate when the

appliance has a malfunction.

BEFORE FIRST USE

During installation or before ﬁrst use

you may observe some water in the

appliance. This is residual water left in

the appliance after a full functional test

in the factory to ensure the appliance

is delivered to customers in perfect

working order and is no cause for

concern.

1. Connect the mains plug to the mains socket.

2. Open the water tap.

3. Put 2 litre of water in the detergent

compartment for washing phase.

This activates the drain system.

4. Put a small quantity of detergent in the

compartment for washing phase.

5. Set and start a programme for cotton at the

highest temperature without laundry.

This removes all possible dirt from the drum and the

tub.

DAILY USE - WASHING ONLY

WARNING! Refer to Safety chapters.

LOADING THE LAUNDRY

1. Open the appliance door.

2. Empty the pockets and unfold the items before

you put them in the appliance.

3. Put the laundry in the drum, one item at a time.

Do not put too much laundry in the drum.

4. Close the door ﬁrmly.

CAUTION! Make sure that no laundry

gets caught between the seal and the

door to avoid risk of water leakage and

damage to the laundry.

Washing heavily oiled, greasy stains

could cause damage to rubber parts

of the washing machine.

USING DETERGENT AND ADDITIVES

1. Measure out the detergent and the fabric

conditioner.

2. Put the detergent and the fabric conditioner

into the compartments.

Always follow the instructions that

you ﬁnd on the packaging of the

detergent products, but we

recommend that you do not

exceed the maximum indicated

level. This quantity will however

guarantee the best washing

results.

3. Carefully close the detergent drawer.

CHECK THE POSITION OF THE DETERGENT

FLAP

1. Pull out the detergent dispenser until it stops.

2. Press the lever down to remove the dispenser.

3. To use powder detergent, turn the ﬂap up.

4. To use liquid detergent, turn the ﬂap down.

With the ﬂap in the position DOWN:

• Do not use gelatinous or thick liquid

detergents.

• Do not exceed to liquid detergent dose

indicated on the ﬂap.

• Do not set the prewash phase.

• Do not set the delay start function.

5. Measure out the detergent and the fabric

conditioner.

6. Carefully close the detergent dispenser.

Make sure that the ﬂap does not cause a blockage

when you close the drawer.

SETTING A PROGRAMME

1. Turn the programme knob to switch the

appliance on and set the required programme:

• The indicator

ﬂashes.

• The display shows the level of the Time

Manager, the programme duration and the

indicators of the phases of the programme.

2. If necessary, change the temperature and the

spin speed or add available options. When you

activate an option, the indicator of the set

option comes on.

If you set something incorrect, the

display shows the message .

STARTING A PROGRAMME WITHOUT THE

DELAY START

Press .

• The indicator of

stops to ﬂash and

stays on.

• The indicator starts to ﬂash on the

display.

• The programme starts, the door locks, the

display shows the indicator .

• The drain pump can operate for a short time

when the appliance ﬁlls water.

After approximately 15 minutes from

the start of the programme:

• The appliance adjusts automatically

the programme duration agree with

the laundry load.

• The display shows the new value.

STARTING A PROGRAMME WITH THE

DELAY START

1. Press Delay Start again and again until the

display shows the delay you want to set.

The related indicator comes on the display.

2. Press :

• The appliance starts the countdown.

• The door locks, the display shows the

indicator .

• When the countdown is completed, the

programme starts automatically.

You can cancel or change the set of

the delay start before you press the

. To cancel the delay start:

• Press to set the appliance

to pause.

• Press until the display

shows '.

• Press again to start the

programme immediately.

INTERRUPTING A PROGRAMME AND

CHANGING THE OPTIONS

You can change only some options before they

operate.

1. Press .

The indicator ﬂashes.

2. Change the options.

3. Press again.

The programme continues.

CANCELLING A RUNNING PROGRAMME

1. Turn the programme knob to position to

cancel the programme and to deactivate the

appliance.

2. Turn the programme knob again to activate the

appliance. Now, you can set a new washing

programme.

Before starting the new programme

the appliance could drain the water. In

this case, make sure that the detergent

is still in the detergent compartment, if

not ﬁll the detergent again.

OPENING THE DOOR

CAUTION! If the temperature and

level of the water in the drum are too

high and the drum still rotates, you

cannot open the door.

While a programme or the delay start operates, the

appliance door is locked and the display shows the

indicator .

Open the appliance door when the

programme or the delay start operates:

1. Press

to pause the appliance.

2. Wait until the door lock indicator goes off.

3. Open the door.

4. Close the door and press again .

The programme or delay start continues to operate.

AT THE END OF THE PROGRAMME

• The appliance stops automatically.

• The acoustic signal operates (if it is activated).

• In the display comes on.

• The indicator of the goes off.

• The door lock indicator goes off.

• You can open the door.

• Remove the laundry from the appliance. Make

sure that the drum is empty.

• Close the water tap.

• Turn the programme knob to position to

deactivate the appliance.

• Keep the door ajar, to prevent the mildew and

odours.

The washing programme is completed, but

there is water in the drum:

• The drum turns regularly to prevent the creases

in the laundry.

Page is loading ...

Zanussi ZWD76NB4PW User manual

Brand: Zanussi

Model: ZWD76NB4PW

Category: Tumble dryers

Type: User manual

Download PDF

report

Zanussi ZWD76NB4PW User manual

Zanussi ZWD76NB4PW User manual

Related papers

Other documents