Simplicity 1694010 User manual

Brand: Simplicity

Model: 1694010

Category: Lawnmowers

Type: User manual

OPERATOR’S

MANUAL

16HP Hydro Tractors

Mfg. No. Description

1694009 Broadmoor, 16HP

1694010 Broadmoor, 16HP

1694011 Conquest, 16HP Hydro

1694018 1606, 16HP Hydro

1694019 1616, 16HP Hydro

1694020 1716H, 16HP Hydro

1694027 2606, 16HP Hydro

1694028 2616, 16HP Hydro

1694029 2716H, 16HP Hydro

1694170 Conquest, 16HP Hydro (CE)

1694179 Broadmoor, 16HP Hydro (CE)

1694207 1616, 16HP Hydro (CE)

1694209 2616, 16HP Hydro (CE)

1694277 Broadmoor, 16HP Hydro

1694279 1626, 16HP Hydro

1694281 2626, 16HP Hydro

1694301 Broadmoor, 16HP Hydro (CE)

1694368 YT1644, 16HP Hydro

1694429 Broadmoor, 16HP Hydro

1694430 Broadmoor, 16HP Hydro (CE)

1694431 2616, 16HP Hydro

1694465 1616, 16HP Hydro

1694487 LT1644, 16HP Hydro

18HP Hydro Tractors

Mfg. No. Description

1694013 Conquest, 18HP Hydro

1694022 1718H, 18HP Hydro

1694031 2718H, 18HP Hydro

1694369 YT1850, 18HP Hydro

1694467 1618, 18HP Hydro

1694468 Broadmoor, 18HP Hydro

1694469 2618, 18HP Hydro

1694470 Conquest, 18HP Hydro (CE)

1694475 YT1844, 18HP Hydro

1694518 YT1844, 18HP Hydro (CE)

20HP Hydro Tractors

Mfg. No. Description

1694014 Conquest, 20HP Hydro

1694015 Prestige, 20HP Hydro

1694016 Prestige, 20HP Hydro PS

1694023 1720H, 20HP Hydro

1694024 1820H, 20HP Hydro

1694025 1820H, 20HP Hydro PS

1694032 2720H, 20HP Hydro

1694033 2820H, 20HP Hydro

1694034 2820H, 20HP Hydro PS

1694172 Prestige, 20HP Hydro (CE)

1694476 YT2050, 20HP Hydro

1694582 Prestige, 20HP Hydro (CE)

23HP Hydro Tractors

Mfg. No. Description

1694017 Prestige, 23HP Hydro PS

1694026 1823H, 23HP Hydro PS

1694035 2823H, 23HP Hydro PS

1694370 GT2354, 23HP Hydro PS

38” Mower Decks

Mfg. No. Description

1694036 38” Mower Deck

1694042 38” Mower Deck

1694453 38” Mower Deck (CE)

40” Mower Decks

Mfg. No. Description

1694041 40” Mower Deck

1694047 40” Mower Deck

1694177 40” Mower Deck (CE)

1694210 40” Mower Deck (CE)

1694339 40” Mower Deck

1694340 40” Mower Deck

1694341 40” Mower Deck (CE)

44” Mower Decks

Mfg. No. Description

1694037 44” Mower Deck

1694038 44” Mower Deck

1694043 44” Mower Deck

1694044 44” Mower Deck

1694173 44” Mower Deck (CE)

1694178 44” Mower Deck (CE)

1694371 44” Mower Deck

1694488 44” Mower Deck

1694519 44” Mower Deck (CE)

50” Mower Decks

Mfg. No. Description

1694039 50” Mower Deck

1694045 50” Mower Deck

1694174 50” Mower Deck (CE)

1694372 50” Mower Deck

54” Mower Decks

Mfg. No. Description

1694040 54” Mower Deck

1694046 54” Mower Deck

1694373 54” Mower Deck

1694366 54” Mower Deck

1694367 54” Mower Deck

1694491 54” Mower Deck

Prestige / 1800 / 2800 / GT

Conquest / 1700 / 2700 / YT

Broadmoor / 1600 / 2600 / LT

Series

1723204

Revision W

05/2009

Not for

Reproduction

Troubleshooting, Adjustment & Service .........33

Troubleshooting the Tractor..................................33

Troubleshooting the Mower ..................................34

Battery Charging ...................................................35

Seat Adjustment....................................................35

Manual Lift Assist Adjustment...............................35

Steering Wheel Adjustment ..................................36

Steering Gear Adjustment.....................................36

Brake Adjustment..................................................36

PTO Clutch Adjustment ........................................37

Mower Adjustments ..............................................38

Gauge Wheels ..............................................38

Leveling the Mower.......................................38

Mower Belt Replacement......................................40

44” & 50” PTO Belt Replacement .................40

54” PTO Belt Replacement ...........................40

Arbor Drive Belt Replacement, 44” 50” 54”...41

40” Mower PTO Belt Replacement ...............42

40” Mower Arbor Drive Belt Replacement ....43

38” Mower Drive Belt Replacement ..............44

Specifications ....................................................45

Parts & Accessories..........................................47

NOTE: In this manual, “left” and “right” are referred to as

seen from the operating position.

Safety Rules & Information.................................3

Identification Numbers........................................6

Safety Decals .......................................................7

Safety Icons .........................................................8

Features & Controls ............................................9

Control Functions....................................................9

Parking Brake Function.........................................11

Automatic Controlled Traction...............................11

Dashboard Display Functions ...............................12

Operating the Tractor ........................................13

Safety Interlock System ........................................13

General Operating Safety .....................................13

Adding Fuel...........................................................13

Starting the Engine ...............................................13

Stopping the Tractor & Engine..............................14

Driving the Tractor ................................................14

Mowing..................................................................14

Pushing the Tractor by Hand ................................14

Using a Mulching Mower.......................................15

Adjusting Mower Cutting Height - 40” Decks ........16

Adjusting Mower Cutting Height - 38” 44” 50” 54”.16

Mower Deck Removal & Installation .....................17

Attaching a Trailer.................................................20

Storage .................................................................20

Lift Variations When Using Attachments...............21

Regular Maintenance ........................................22

Maintenance Schedule .........................................22

Check / Clean Oil Cooler ......................................23

Safety Interlock System Check .............................23

Blade Brake Check ...............................................23

PTO Clutch Adjustment Check .............................23

Engine Maintenance .............................................23

Checking Tire Pressures.......................................24

Battery Maintenance .............................................24

Lubrication ............................................................25

Lubricate Rear Axes .............................................26

Servicing the Mower Blades .................................27

Check Mower Blade Timing ..................................28

Transmission Identification ...................................29

Transmission Maintenance ...................................29

Table of Contents

Not for

Reproduction

GENERAL OPERATION

1. Read, understand, and follow all instructions in the

manual and on the unit before starting.

2. Do not put hands or feet near rotating parts or under

the machine. Keep clear of the discharge opening at

all times.

3. Only allow responsible adults, who are familiar with

the instructions, to operate the unit (local regulations

can restrict operator age).

4. Clear the area of objects such as rocks, toys, wire,

etc., which could be picked up and thrown by the

blade(s).

5. Be sure the area is clear of other people before mow-

ing. Stop the unit if anyone enters the area.

6. Never carry passengers.

7. Do not mow in reverse unless absolutely necessary.

Always look down and behind before and while travel-

ling in reverse.

8. Never direct discharge material toward anyone.

Avoid discharging material against a wall or obstruc-

tion. Material may ricochet back toward the operator.

Stop the blade(s) when crossing gravel surfaces.

9. Do not operate the machine without the entire grass

catcher, discharge guard (deflector), or other safety

devices in place.

10. Slow down before turning.

11. Never leave a running unit unattended. Always disen-

gage the PTO, set parking brake, stop engine, and

remove keys before dismounting.

12. Disengage blades (PTO) when not mowing. Shut off

engine and wait for all parts to come to a complete

stop before cleaning the machine, removing the grass

catcher, or unclogging the discharge guard.

13. Operate the machine only in daylight or good artificial

light.

14. Do not operate the unit while under the influence of

alcohol or drugs.

15 Watch for traffic when operating near or crossing

roadways.

16. Use extra care when loading or unloading the unit

into a trailer or truck.

17. Always wear eye protection when operating this unit.

18. Data indicates that operators, age 60 years and

above, are involved in a large percentage of riding

mower-related injuries. These operators should eval-

uate their ability to operate the riding mower safely

enough to protect themselves and others from injury.

19. Follow the manufacturer’s recommendations for

wheel weights or counterweights.

20. Keep in mind the operator is responsible for accidents

occurring to other people or property.

21. All drivers should seek and obtain professional and

practical instruction.

22. Always wear substantial footwear and trousers.

Never operate when barefoot or wearing sandals.

23. Before using, always visually check that the blades

and blade hardware are present, intact, and secure.

Replace worn or damaged parts.

24. Disengage attachments before: refueling, removing

an attachment, making adjustments (unless the

adjustment can be made from the operator’s posi-

tion).

25. When the machine is parked, stored, or left unattend-

ed, lower the cutting means unless a positive

mechanical lock is used.

26. Before leaving the operator’s position for any reason,

engage the parking brake, disengage the PTO, stop

the engine, and remove the key.

27. To reduce fire hazard, keep the unit free of grass,

leaves, & excess oil. Do not stop or park over dry

leaves, grass, or combustible materials.

28. It is a violation of California Public Resource Code

Section 4442 to use or operate the engine on or near

any forest-covered, brush-covered, or grass-covered

land unless the exhaust system is equipped with a

spark arrester meeting any applicable local or state

laws. Other states or federal areas may have similar

laws.

Read these safety rules and follow them closely. Failure to obey these rules could result in loss of control

of unit, severe personal injury or death to you, or bystanders, or damage to property or equipment.

This mowing deck is capable of amputating hands and feet and throwing objects.

The triangle in text signifies important cautions or warnings which must be followed.

Safety Rules & Information

TRANSPORTING AND STORAGE

1. When transporting the unit on an open trailer, make

sure it is facing forward, in the direction of travel. If

the unit is facing backwards, wind lift could damage

the unit.

2. Always observe safe refueling and fuel handling prac-

tices when refueling the tractor after transportation or

storage.

3. Never store the unit (with fuel) in an enclosed poorly

ventilated structure. Fuel vapors can travel to an

ignition source (such as a furnace, water heater, etc.)

and cause an explosion. Fuel vapor is also toxic to

humans and animals.

4. Always follow the engine manual instructions for

storage preparations before storing the unit for both

short and long term periods.

5. Always follow the engine manual instructions for

proper start-up procedures when returning the unit to

service.

6. Never store the unit or fuel container inside where

there is an open flame or pilot light, such as in a

water heater. Allow unit to cool before storing.

TP 600-2459-06-UV-SMA

Not for

Reproduction

CHILDREN

Tragic accidents can occur if the operator is not alert to the

presence of children. Children are often attracted to the

unit and the mowing activity. Never assume that children

will remain where you last saw them.

1. Keep children out of the mowing area and under the

watchful care of another responsible adult.

2. Be alert and turn unit off if children enter the area.

3. Before and during reverse operation, look behind and

down for small children.

4. Never carry children, even with the blade(s) off. They

may fall off and be seriously injured or interfere with

safe unit operation. Children who have been given

rides in the past may suddenly appear in the mowing

area for another ride and be run over or backed over

by the machine.

5. Never allow children to operate the unit.

6. Use extra care when approaching blind corners,

shrubs, trees, or other objects that may obscure

vision.

EMISSIONS

1. Engine exhaust from this product contains chemicals

known, in certain quantities, to cause cancer, birth

defects, or other reproductive harm.

2. Look for the relevant Emissions Durability Period and

Air Index information on the engine emissions label.

IGNITION SYSTEM

1. This spark ignition system complies with Canadian

ICES-002.

Safety Rules and Information

SLOPE OPERATION

Slopes are a major factor related to loss-of-control and tip-

over accidents, which can result in severe injury or death.

Operation on all slopes requires extra caution. If you can-

not back up the slope or if you feel uneasy on it, do not

operate on it.

Control of a ride-on machine sliding on a slope will not be

regained by the application of the brake. The main rea-

sons for loss of control are: insufficient tire grip on the

ground, speed too fast, inadequate braking, the type of

machine is unsuitable for its task, lack of awareness of the

ground conditions, incorrect hitching and load distribution.

1. Mow up and down slopes, not across.

2. Watch for holes, ruts, or bumps. Uneven terrain could

overturn the unit. Tall grass can hide obstacles.

3. Choose a slow speed so that you will not have to

stop or change speeds while on the slope.

4. Do not mow on wet grass. Tires may loose traction.

5. Always keep unit in gear especially when traveling

down slopes. Do not shift to neutral and coast down-

hill.

6. Avoid starting, stopping, or turning on a slope. If tires

lose traction, disengage the blade(s) and proceed

slowly straight down the slope.

7. Keep all movement on slopes slow and gradual. Do

not make sudden changes in speed or direction,

which could cause the machine to rollover.

8. Use extra care while operating machines with grass

catchers or other attachments; they can affect the

stability of the unit.

9. Do not try to stabilize the machine by putting your

foot on the ground.

10. Do not mow near drop-offs, ditches, or embank-

ments. The mower could suddenly turn over if a

wheel is over the edge of a cliff or ditch, or if an edge

caves in.

11. Do not use grass catchers on steep slopes.

12. Do not mow slopes you cannot back up.

13. See your authorized dealer/retailer for recommenda-

tions of wheel weights or counterweights to improve

stability.

14. Remove obstacles such as rocks, tree limbs, etc.

15. Use slow speed. Tires may lose traction on slopes

even through the brakes are functioning properly.

16. Do not turn on slopes unless necessary, and then,

turn slowly and gradually downhill, if possible.

TOWED EQUIPMENT

1. Tow only with a machine that has a hitch designed

for towing. Do not attach towed equipment except at

the hitch point.

2. Follow the manufacturer’s recommendations for

weight limit for towed equipment and towing on

slopes.

3. Never allow children or others in or on towed equip-

ment.

4. On slopes, the weight of the towed equipment may

cause loss of traction and loss of control.

5. Travel slowly and allow extra distance to stop.

6. Do not shift to neutral and coast down hill.

WARNING

Never operate on slopes greater than 17.6 percent

(10°) which is a rise of 3-1/2 feet (106 cm) vertically in

20 feet (607 cm) horizontally.

When operating on slopes use additional wheel

weights or counterweights. See your dealer/retailer

to determine which weights are available and

appropriate for your unit.

Select slow ground speed before driving onto slope.

In addition to front weights, use extra caution when

operating on slopes with rear-mounted grass

catchers.

Mow UP and DOWN the slope, never across the

face, use caution when changing directions and DO

NOT START OR STOP ON SLOPE.

Not for

Reproduction

Safety Rules & Information

SERVICE AND MAINTENANCE

Safe Handling of Gasoline

1. Extinguish all cigarettes, cigars, pipes, and other

sources of ignition.

2. Use only approved gasoline containers.

3. Never remove the gas cap or add fuel with the engine

running. Allow the engine to cool before refueling.

4. Never fuel the machine indoors.

5. Never store the machine or fuel container where

there is an open flame, spark, or pilot light such as

near a water heater or other appliance.

6. Never fill containers inside a vehicle or on a truck bed

with a plastic bed liner. Always place containers on

the ground away from your vehicle before filling.

7. Remove gas-powered equipment from the truck or

trailer and refuel it on the ground. If this is not possi-

ble, then refuel such equipment on a trailer with a

portable container, rather than from a gasoline dis-

penser nozzle.

8. Keep nozzle in contact with the rim of the fuel tank or

container opening at all times until fueling is com-

plete. Do not use a nozzle lock-open device.

9. If fuel is spilled on clothing, change clothing immedi-

ately.

10. Never over-fill the fuel tank. Replace gas cap and

tighten securely.

11. Use extra care in handling gasoline and other fuels.

They are flammable and vapors are explosive.

12. If fuel is spilled, do not attempt to start the engine but

move the machine away from the area of spillage and

avoid creating any source of ignition until fuel vapors

have dissipated.

13. Replace all fuel tank caps and fuel container caps

securely.

Service & Maintenance

1. Maintain or replace safety and instruction labels as

necessary.

2. Never run the unit in an enclosed area where carbon

monoxide fumes may collect.

3. Keep nuts and bolts, especially blade attachment

bolts, tight and keep equipment in good condition.

4. Never tamper with safety devices. Check their proper

operation regularly and make necessary repairs if

they are not functioning properly.

5. Keep unit free of grass, leaves, or other debris build-

up. Clean up oil or fuel spillage.

6. Stop and inspect the equipment if you strike an

object. Repair, if necessary, before restarting.

7. Never make adjustments or repairs with the engine

running unless specified otherwise in the engine man-

ufacturer’s manual.

8. Do not remove the fuel filter when the engine is hot

as spilled gasoline may ignite. Do not spread fuel line

clamps further than necessary. Ensure clamps grip

hoses firmly over the filter after installation.

9. Do not use gasoline containing METHANOL, gasohol

containing more than 10% ETHANOL, gasoline addi-

tives, or white gas because engine/fuel system dam-

age could result.

10. If the fuel tank must be drained, it should be drained

outdoors.

11. Replace faulty silencers/mufflers.

12. Grass catcher components are subject to wear, dam-

age, and deterioration, which could expose moving

parts or allow objects to be thrown. Frequently check

components and replace with manufacturer’s recom-

mended parts, when necessary.

13. Mower blades are sharp and can cut. Wrap the

blade(s) or wear gloves, and use extra caution when

servicing them.

14. Check brake operation frequently. Adjust and service

as required.

15. Use only factory authorized replacement parts when

making repairs.

16. Always comply with factory specifications on all set-

tings and adjustments.

17. Only authorized service locations should be utilized

for major service and repair requirements.

18. Never attempt to make major repairs on this unit

unless you have been properly trained. Improper ser-

vice procedures can result in hazardous operation,

equipment damage and voiding of manufacturer’s

warranty.

19. On multiple blade mowers, take care as rotating one

blade can cause other blades to rotate.

20. Do not change engine governor settings or over-

speed the engine. Operating the engine at excessive

speed can increase the hazard of personal injury.

21. Disengage drive attachments, stop the engine,

remove the key, and disconnect the spark plug

wire(s) before: clearing attachment blockages and

chutes, performing service work, striking an object, or

if the unit vibrates abnormally. After striking an

object, inspect the machine for damage and make

repairs before restarting and operating the equip-

ment.

22. Never place hands near the moving parts, such as a

hydro pump cooling fan, when the tractor is running.

(Hydro pump cooling fans are typically located on top

of the transaxle).

23. Units with hydraulic pumps, hoses, or motors: WARN-

ING: Hydraulic fluid escaping under pressure may

have sufficient force to penetrate skin and cause seri-

ous injury. If foreign fluid is injected into the skin it

must be surgically removed within a few hours by a

doctor familiar with this form of injury or gangrene

may result. Keep body and hands away from pin

holes or nozzles that eject hydraulic fluid under high

pressure. Use paper or cardboard, and not hands, to

search for leaks. Make sure all hydraulic fluid con-

nections are tight and all hydraulic hoses and lines

are in good condition before applying pressure to the

system. If leaks occur, have the unit serviced imme-

diately by your authorized dealer.

24. WARNING: Stored energy device. Improper release

of springs can result in serious personal injury.

Springs should be removed by an authorized techni-

cian.

25. Models equipped with an engine radiator: WARNING:

Stored energy device. To prevent serious bodily

injury from hot coolant or steam blow-out, never

attempt to remove the radiator cap while the engine is

running. Stop the engine and wait until it is cool.

Even then, use extreme care when removing the cap.

Not for

Reproduction

Identification Numbers

Tractor ID Tag

Mower ID Tag

ENGINE REFERENCE DATA

Model Description Name/Number

Unit MFG Number

PRODUCT REFERENCE DATA

Unit SERIAL Number

Dealer Name

Date Purchased

Engine Make

Engine Type/Spec

Engine Model

Engine Code/Serial Number

Mower Deck MFG Number

Mower Deck SERIAL

Number

Identification Numbers

When contacting your authorized dealer for replace-

ment parts, service, or information you MUST have

these numbers.

Record your model name/number, manufacturer’s identi-

fication numbers, and engine serial numbers in the

space provided for easy access. These numbers can be

found in the locations shown.

NOTE: For location of engine identification numbers,

refer to the engine owner’s manual.

Part No. xxxxxxx

xxxxxxxxxxxxxxx

Serial No. xxxxxxxxxx

20xx

kW: x.xx

xxxx max

xxxxxxxxxxxxxxxxxxxxxxx

xxx

kg: xxx

North American /

CE Models

(Only)

CE IDENTIFICATION TAG MARKINGS

A. Manufacturer’s Identification Number

B. Manufacturer’s Serial Number

C. Power Rating in Kilowatts

D. Maximum Engine Speed in Rotations per Minute

E. Manufacturer’s Name and Address

F. Year of Manufacture

G. CE Compliance Logo

H. Mass of Unit in Kilograms

I. Guaranteed Sound Power in Decibels

Identification Numbers

Part No. xxxxxxx

xxxxxxxxxxxxxxx

Serial No. xxxxxxxxxx

20xx

kW: x.xx

xxxx max

xxxxxxxxxxxxxxxxxxxxxxx

xxx

kg: xxx

Not for

Reproduction

Safety Decals

SAFETY DECALS

This unit has been designed and manufactured to pro-

vide you with the safety and reliability you would expect

from an industry leader in outdoor power equipment

manufacturing.

Although reading this manual and the safety instructions

it contains will provide you with the necessary basic

knowledge to operate this equipment safely and effec-

tively, we have placed several safety labels on the unit to

remind you of this important information while you are

operating your unit.

All DANGER, WARNING, CAUTION and instructional

messages on your rider and mower should be carefully

read and obeyed. Personal bodily injury can result when

these instructions are not followed. The information is for

your safety and it is important! The safety decals below

are on your rider and mower.

If any of these decals are lost or damaged, replace them

at once. See your local dealer for replacements.

These labels are easily applied and will act as a constant

visual reminder to you, and others who may use the

equipment, to follow the safety instructions necessary for

safe, effective operation.

Decal - Danger, Side-

Discharge Models

Part No. 1704276

ROTATING CUTTING BLADE

Do not put hands or feet

under mower deck while

blade is rotating.

DANGER

1720660

Decal - Danger, Mulching Models

Part No. 1720660

Decal - Danger, Side

Discharge Models

Part No. 1704277

Decal - Transmission Release

Part No. 1723160

Decal - Ignition Switch

Positions

Part No. 1722806

Decal - Operating Instructions, North American

Models, Part No. 1722814

DANGER

OPERATING ON SLOPES CAN BE

DANGEROUS

SEE OPERATOR'S MANUAL. IF YOU CANNOT

BACK-UP A HILL, DO NOT DRIVE ON IT.

ROTATING BLADES CUT OFF

ARMS AND LEGS

STOP MOWER WHEN CHILDREN ARE NEAR.

NO RIDERS — THEY FALL OFF.

DANGER

AVOID SERIOUS

INJURY OR DEATH

• READ OPERATOR'S MANUAL(S).

• KNOW LOCATION AND FUNCTION OF ALL CONTROLS.

• KEEP SAFETY DEVICES (GUARDS, SHIELDS, SWITCHES,

ETC.) IN PLACE AND WORKING.

• REMOVE OBJECTS THAT COULD BE THROWN BY

THE BLADE.

• DO NOT MOW WHEN CHILDREN OR OTHERS

ARE AROUND.

• NEVER CARRY CHILDREN EVEN WITH BLADES OFF.

• LOOK DOWN AND BEHIND BEFORE AND WHILE

BACKING.

• AVOID SUDDEN TURNS.

• IF YOU CANNOT BACK UP A HILL,

DO NOT OPERATE ON IT.

• GO UP AND DOWN SLOPES, NOT ACROSS.

• IF MACHINE STOPS GOING UPHILL, STOP BLADE

AND BACK DOWN SLOWLY.

• BE SURE BLADE(S) AND ENGINE ARE STOPPED

BEFORE PLACING HANDS OR FEET NEAR BLADE(S).

• WHEN LEAVING MACHINE, SHUT OFF ENGINE,

REMOVE KEY, AND SET PARKING BRAKE.

WARNING

1722814-00

DO NOT TOW TRACTOR! Damage may result to transmission

Decal - Operating Instructions, CE Models,

Part No. 1723175

1723175

NORTH AMERICAN MODELS

ALL MODELS

CE MODELS

Decal - Danger, Rotating Blades

Part No. 1720389

Decal - Cutting

Height

Part No. 1723470

1723470

Decal - Cutting

Height

Part No. 1723847

1723847

Not for

Reproduction

CE Safety Icons

Warning: Read Operator’s

Manual.

Read and understand the

Operator’s Manual before using

this machine.

Danger: Thrown Objects.

This machine is capable of throwing

objects and debris. Keep

bystanders away.

Warning: Remove Key Before

Servicing.

Remove the key and consult techni-

cal literature before performing

repairs or maintenance.

Danger: Machine Rollover.

Do not use this machine on slopes

greater than 10°.

Danger: Dismemberment.

This machine can amputate limbs.

Keep bystanders and children away

when engine is running.

Danger: Dismemberment.

This mower deck can amputate

limbs. Keep hands and feet away

from blades.

SAFETY ICONS

Not for

Reproduction

Features & Controls

Throttle/Choke Control

(Single Lever Models)

The throttle/choke lever controls engine speed and

choke. Move the throttle forward to increase engine

speed and back to decrease engine speed. Always

operate at FULL throttle. Move the control fully forward

(past the detent) to close the choke. Close the choke for

cold starting. Open the choke once the engine starts. A

warm engine may not require choking.

Throttle Control

(Twin Lever Models)

The throttle controls engine speed. Move the throttle for-

ward to increase engine speed and back to decrease

engine speed. Always operate at FULL throttle.

Choke

(Twin Lever Models)

Close the choke for cold starting. Open the choke once

the engine starts. A warm engine may not require chok-

ing. Move the lever forward to close the choke.

CONTROL FUNCTIONS

The information below briefly describes the function of individual controls. Starting, stopping, driving, and mowing

require the combined use of several controls applied in specific sequences. To learn what combination and sequence

of controls to use for various tasks see the OPERATION section.

Figure 1. Controls

Hydraulic

Lift

Models

Select

Manual

Lift Models

Select

Manual

Lift Models

38”, 44”, 50”,

& 54” Models

40” Models

Not for

Reproduction

Headlights

The light switch turns the tractor headlights on and off.

PTO Switch

The PTO (Power Take-Off) switch engages and disen-

gages attachments that use the PTO. To engage the

PTO, pull UP on the switch. Push DOWN to disengage.

Note that the operator must be seated firmly in the trac-

tor seat for the PTO to function.

Ignition Switch

The ignition switch starts and stops the engine, it has

three positions:

OFF Stops the engine and shuts off the

electrical system.

RUN Allows the engine to run and powers the

electrical system.

START Cranks the engine for starting.

NOTE: Never leave the ignition switch in the RUN posi-

tion with the engine stopped–this drains the battery.

Brake Pedal

Depressing the brake pedal applies the tractor brake.

Ground Speed Pedals

The tractor’s forward ground speed is controlled by the

forward ground speed control pedal. The tractor’s

reverse ground speed is controlled by the reverse

ground speed control pedal.

Depressing either pedal will increase ground speed.

Note that the further down the pedal is depressed, the

faster the tractor will travel.

Parking Brake

The parking brake knob is used to lock the parking brake

when the tractor is stopped. Fully depressing the brake

pedal and pulling up on the knob engages the parking

brake. Refer to page 10 for a full explanation of parking

brake functions.

Mower Height of Cut Adjustment

38”, 44”, 50”, & 54” MOWER DECKS

The cutting height adjustment knob controls the mower

cutting height. The cutting height is infinitely adjustable

between 1” and 3-5/8.”

Features & Controls

40” MOWER DECKS

The cutting height adjustment lever controls the mower

cutting height. Push down on the button to release the

lever, move to the desired cutting height, and release the

button to lock. The cutting height is infinitely adjustable

between 1” and 3-5/8.”

Cutting Height Fine Tuning Adjustment

(40” Mower Decks Only)

The cutting height fine tuning adjustment is used to set

the mower cutting height between two of the preset cut-

ting positions.

Cruise Control

The cruise control is used to lock the ground speed con-

trol in forward. Move the lever forward until the desired

ground speed is reached. To disengage the cruise con-

trol move the lever back. In the event you need to stop

quickly, depressing the brake pedal will also return the

cruise control to neutral.

Seat Adjustment Lever

The seat can be adjusted forward and back. Move the

lever, position the seat as desired, and release the lever

to lock the seat into position.

Transmission Release Valve Lever

The transmission release valve lever deactivates the

transmission so that the tractor can be pushed by hand.

See PUSHING THE TRACTOR BY HAND for opera-

tional information.

Transmission Oil Expansion Chamber

(K71 Models Only)

Transmission oil is added through the transmission oil

expansion chamber. It also serves as extra holding

capacity for oil as the transmission heats up and the oil

expands. See TRANSMISSION MAINTENANCE for oil

level check and fill procedures.

Fuel Tank

To remove the cap, turn counterclockwise. On models

with a dashboard display, the fuel gauge is part of the

dashboard. Models without a dashboard display have a

fuel gauge located under the seat.

Differential Lock Pedal (Select Models)

Depressing this pedal locks the transmission differential,

locking both rear wheels into “drive”.

Use this feature if the tractor is stuck because one wheel

is slipping. Engage the differential lock at slow

ground speeds only.

Not for

Reproduction

Features & Controls

Figure 2. Engaging the Parking Brake

A. Ground Speed Pedals

B. Brake Pedal

C. Parking Brake Knob

PARKING BRAKE FUNCTION

Applying the Parking Brake - See Figure 2. To lock

the parking brake, release the ground speed pedals (A),

fully depress the brake pedal (B), pull UP on the parking

brake knob (C), and then release brake pedal.

Releasing the Parking Brake - See Figure 2. To

release the parking brake, fully depress the brake pedal

(B) and push the parking brake knob (C) DOWN.

IMPORTANT NOTE: The tractor’s hydraulic attachment

lift will not work when the parking brake is engaged.

AUTOMATIC CONTROLLED

TRACTION

What is Automatic Controlled Traction?

Automatic Controlled Traction (ACT) is an exclusive fea-

ture of our transmissions that provides improved traction.

ACT applies a preset amount of torque to both rear

wheels even if one starts slipping (a transmission without

ACT will lose traction completely if one rear wheel starts

slipping). This preset torque is just enough to provide

additional traction, and still allow the wheels to turn at dif-

ferent speeds in a tight turn without damaging the lawn.

What to Expect from Your ACT Tractor

For the most part, while using your tractor you will not

notice ACT working, and you will simply become accus-

tomed to increased traction an ACT transmission pro-

vides.

Under certain circumstances the ACT system limit can

be exceeded, and one of the rear wheels may slip (for

instance if trying to turn up a hill while accelerating).

This is normal. If you start to lose traction, do not speed

up. Instead, slow to a stop, straighten the steering

wheel, and slowly accelerate. Stopping the tractor

allows the transmission to regain more traction.

Steering Tilt Adjust (Select Models)

Use the tilt knob located on the bellows to release the

pivot mechanism and pivot the wheel to the desired posi-

tion. Release the tilt knob to lock in position.

Attachment Lift Control Lever

When using the mower deck, lift the deck off the ground

while transporting to and from the job site. DO NOT cut

with the mower in the raised, transport position.

Hydraulic Lift Models: The attachment lift control lever

raises and lowers attachments that utilize the tractor’s

hydraulic lift cylinder. Pushing the lever forward lowers

the attachment while pulling the lever back raises the

attachment.

IMPORTANT NOTE - On models equipped with

hydraulic lift, the attachment lift will not work when the

parking brake is engaged.

Manual Lift Models: The attachment lift control lever

raises and lowers attachments that utilize the tractor’s

manual lift linkage. To lower an attachment: pull the

lever back slightly, depress the release button, and push

the lever forward until it locks in the lowered position. To

raise an attachment: push the lever forward slightly,

depress the release button, then pull the lever back until

it locks in the raised position.

Not for

Reproduction

Features & Controls

DASHBOARD DISPLAY

(SELECT MODELS)

Display Items

Refer to Figures 3a and 3b.

A. FUEL LEVEL

Indicates the amount of fuel in the fuel tank. Left is

empty; right is full.

B. HOUR METER / CLOCK / SERVICE INDICATOR

Displays the clock, hour meter, and maintenance

reminder.

C. SELECT BUTTON

Used to set the clock and reset the maintenance

reminder.

D. SET BUTTON

Used to set the clock and reset the maintenance

reminder.

E. PTO LIGHT

Indicates the PTO switch is in the ON position.

F. CRUISE CONTROL LIGHT

Indicates that the cruise control is engaged.

G. LOW OIL PRESSURE LIGHT

Indicates that the engine oil pressure is low. The light

will turn on when the tractor is first started and then go

out. IF THIS LIGHT TURNS ON WHILE THE TRACTOR

IS IN USE, TURN THE ENGINE OFF IMMEDIATELY.

Contact your authorized dealer for service.

H. LOW VOLTAGE LIGHT

Indicates that the electrical system voltage is low. The

light will turn on when the tractor is first started and then

go out. IF THIS LIGHT TURNS ON WHILE THE TRAC-

TOR IS IN USE, TURN THE ENGINE OFF IMMEDIATE-

LY. Contact your authorized dealer for service.

Functions

EARLY MODELS (SEE FIGURE 3A)

Display Total Running Hours - When the key switch is

first turned to the RUN position, all warning indicators will

light and the total running hours will be displayed. Be

sure all lights are functioning.

Display PTO Hours - Turn the key OFF, engage the

PTO, and turn the key to RUN (engine off).

Set the Clock - Press and release the select button (C)

to select hours or minutes. Depress the set button (D) to

advance the selected number.

Demonstration Mode - Turn the key OFF, depress and

hold the set button (D, Figure 3), turn the key to RUN

and release the set button.

Figure 3a. Dashboard Display - Early Models

F E

Figure 3b. Dashboard Display - Later Models

Cruise PTO

F E

Maintenance Reminder - A maintenance reminder will

display in the information window (B) after the first 5

hours of operation, and then after every 50 hours. The

reminder will automatically reset after 5 hours.

LATER MODELS (SEE FIGURE 3B)

Display Total Running Hours - When the key switch is

first turned to the RUN position, all warning indicators will

light and the total running hours will be displayed. Be

sure all lights are functioning.

Display PTO Hours - Turn the key OFF, engage the

PTO, and turn the key to RUN (engine off).

Set the Clock - Press and release the select button (C)

to select hours or minutes. Depress the set button (D) to

advance the selected number.

Demonstration Mode - With the engine off, hold down

the set button (D) and turn the key switch to RUN.

Maintenance Reminder - A maintenance reminder will

display in the information window (B) after the first 5

hours of operation, and then after every 50 hours. The

reminder will automatically reset after 5 hours. The

reminder can be manually reset by turning the key switch

from OFF to RUN (with engine off) and then depressing

the set (D) and select (C) buttons simultaneously for 5

seconds.

Not for

Reproduction

Operating the Tractor

GENERAL OPERATING SAFETY

Be sure to read all information in the Safety and

Operation sections before attempting to operate this unit.

Become familiar with all of the controls and how to stop

the unit.

ADDING FUEL

To add fuel:

1. Remove the fuel cap (A, Figure 4).

2. Fill the tank. Do not overfill. Leave room in the tank

for fuel expansion. Refer to your engine manual for

specific fuel recommendations.

3. Install and hand tighten the fuel cap.

STARTING THE ENGINE

1. While sitting in the operator’s seat, fully depress the

brake pedal or set the parking brake.

2. Make sure that your feet are not depressing the

ground speed control pedals and that the cruise con-

trol lever is in neutral.

3. Disengage the PTO clutch.

4. Set the throttle to FULL.

5. Close the choke.

NOTE: A warm engine may not require choking.

6. Insert the ignition key and turn it to START.

7. After the engine starts, move the engine throttle con-

trol to SLOW. Warm up the engine by running it for at

least a minute.

8. Set throttle to FULL.

NOTE: In the event of an emergency the engine can be

stopped by simply turning the ignition switch to STOP.

Use this method only in emergency situations. For nor-

mal engine shut down follow the procedure given in

STOPPING THE TRACTOR.

WARNING

Gasoline is highly flammable and must be

handled with care. Never fill the tank when the

engine is still hot from recent operation. Do not

allow open flame, smoking or matches in the

area. Avoid over-filling and wipe up any spills.

Do not use gasoline containing METHANOL,

gasohol containing more than

10% ETHANOL, gasoline additives, or white

gas because engine/fuel system damage

could result.

SAFETY INTERLOCK

SYSTEM TESTS

This unit is equipped with safety interlock switches and

other safety devices. These safety systems are pre-

sent for your safety: do not attempt to bypass safety

switches, and never tamper with safety devices. Check

their operation regularly.

Operational SAFETY Checks

Your unit is equipped with a seat switch safety system.

Check the seat switch operation every fall and spring

with the following tests.

Test 1 — Engine should NOT crank if:

• PTO switch is ON, OR

• Brake pedal is NOT fully depressed (parking brake

OFF), OR

• The cruise control lever is NOT in NEUTRAL.

Test 2 — Engine SHOULD crank if:

• PTO switch is OFF, AND

• Brake pedal is fully depressed (parking brake ON),

AND

• The cruise control lever is in NEUTRAL.

Test 3 — Engine should SHUT OFF if:

• Operator rises off seat with PTO engaged, OR

• Operator rises off seat with brake pedal NOT fully

depressed (parking brake OFF).

Test 4 — Blade Brake Check

Mower blades and mower drive belt should come to a

complete stop within five seconds after electric PTO

switch is turned OFF (or operator rises off seat). If

mower drive belt does not stop within five seconds,

readjust the PTO clutch as described in the ADJUST-

MENTS section or see your dealer.

NOTE: Once the engine has stopped, the PTO switch

must be turned off after the operator returns to the seat

in order to start the engine.

WARNING

If the unit does not pass a safety test, do not

operate it. See your authorized dealer. Under no

circumstance should you attempt to defeat the

purpose of the safety interlock system.

Not for

Reproduction

STOPPING THE TRACTOR & ENGINE

1. Return the ground speed control(s) to neutral.

2. Disengage the PTO and wait for all moving parts to

stop.

3. Place the throttle control in the position specified in

the engine owner’s manual provided in the operator's

packet shipped with your tractor. Follow any recom-

mended stopping procedures.

4. Turn the ignition switch to OFF. Remove the key.

DRIVING THE TRACTOR

1. Sit in the seat and adjust the seat so that you can

comfortably reach all the controls and see the dash-

board display.

2. Engage the parking brake.

3. Make sure the PTO switch is disengaged.

4. Start the engine (see STARTING THE ENGINE).

5. Disengage the parking brake and release the brake

pedal.

6. Depress the forward ground speed control pedal to

travel forward. Release the pedal to stop. Note that

the further down the pedal is depressed the faster the

tractor will travel.

7. Stop the tractor by releasing the ground speed con-

trol pedals, setting the parking brake, and stopping

the engine (see STOPPING THE TRACTOR AND

ENGINE).

Operating the Tractor

DO NOT TOW TRACTOR

Towing the unit will cause transmission

damage. • Do not use another vehicle to

push or pull this unit. • Do not actuate the

transmission release valve lever while the

engine is running.

Figure 4. Transmission Release Lever & Fuel Tank

A. Fuel Tank Cap.

B. Transmission Release Lever

MOWING

1. Set the mower cutting height to the desired level and

set the gauge wheels to the appropriate position (if

equipped).

2. Engage the parking brake. Make sure the PTO

switch is disengaged.

3. Start the engine (see STARTING THE ENGINE).

4. Fully lower the mower using the attachment lift lever.

5. Set the throttle to FULL.

6. Engage the PTO (Mower Deck).

7. Begin mowing. See Section LC for tips on mowing

patterns, lawn care, and troubleshooting information.

8. When finished, shut off the PTO and raise the mower

using the attachment lift control lever.

9. Stop the engine (see STOPPING THE TRACTOR

AND ENGINE).

PUSHING THE TRACTOR BY HAND

1. Disengage the PTO and turn the engine off.

2. Pull the transmission release (B, Figure 4) back

approximately 2-1/2” (6 cm) to lock into released

position.

3. The tractor can now be pushed by hand.

Not for

Reproduction

Operating the Tractor

USING A MULCHING MOWER

(40” MOWER ONLY)

Benefits of Proper Mulching

Mulching consists of a mower deck which cuts and

recuts clippings into tiny particles and then blows them

down into the lawn. These tiny particles decompose

rapidly into by-products that your lawn can use. Under

proper conditions your mulching mower virtually elimi-

nate noticeable clippings on the lawn surface.

Limitations of Mulching Decks

Mulching mowers cannot function properly if the grass is

wet, or if the grass is simply too high. Even more than

normal mowing, mulching requires that the grass be dry

and that no more than 1/3 of the height is cut.

Do not use the mower as a mulching mower during the

first two or three cuttings in the spring. The long grass

blades, quick growth, and often wetter conditions are

more suitable for broadcasting (side-discharging).

Correct Ground Speed & Engine Speed

Use full engine throttle to maximize mower blade tip

speed matched with a slow ground speed so that clip-

pings will be finely cut. Ground speed while mulching

should be half the speed used when broadcasting (side-

discharging) under similar conditions. Since mulching

requires more horse power than broadcasting, using a

proper ground speed is vitally important for good

mulching operation.

Correct Cutting Height

Cutting off too much at one time shocks the plant’s

growth system and weakens the grass. A good rule of

thumb is the 1/3 rule: to cut no more than one third of the

grass height, and never more than 1 inch (2,5cm) at a

time.

The best mulching action typically results from cutting

only the top 1/2” to 3/4” (1,25 - 2cm) of the grass blade.

This provides short clippings which decompose properly

(much more quickly than longer clippings). The ideal

cutting height will vary with climate, time of year, and

quality of your lawn. We recommend that you experi-

ment with both the cutting height and ground speed to

achieve the best cut. Start with a high cutting height and

use progressively lower heights until you find a cutting

height that is matched to your mowing conditions and

preferences. For best results, overlapping is recom-

mended.

Using the Side Discharge Deflector

When to use the side discharge deflector: If you’ve

been on vacation or missed a mowing and the grass has

gotten very long, do not try to mulch at your normal cut-

ting height. To handle these situations your mulching

mower is equipped with a side discharge deflector.

Installing the side discharge deflector allows you to

broadcast clippings. Broadcasting, or side-discharging,

disperses fine clippings evenly over the entire lawn.

Always operate the engine at full throttle. Use an appro-

priate ground speed for the thickness and height of grass

you are cutting. If you hear the engine slowing down,

you are mowing too fast, use a slower ground speed.

Mow when the grass is 3”-5” (7,6-12,7cm) long. Do not

cut off more than 1” (2,5cm) in a single pass.

To install the side discharge chute:

1. Lift up the mulching cover (B, Figure 5).

2. Install the side discharge deflector (A) under the

mulching cover. The side discharge deflector hooks

onto the mulching cover hinge rod, and is held in

place by the mulching cover.

3. Release the mulching cover.

Figure 5. Installing the Side Discharge Deflector

A. Side Discharge Deflector

B. Mulching Cover

WARNING

Never operate the mower deck without either the

discharge chute or mulching deflector in place.

Not for

Reproduction

Operating the Tractor

Figure 7. Raising & Lowering Mower - 40” Mowers

A. Mower Lift Lever

B. Mower Height Adjuster

Figure 6. Cutting Height Adjustment - 40” Mowers

A. Cutting Height Lever

B. Fine Tuning Adjustment

ADJUSTING MOWER CUTTING

HEIGHT - 40” MOWER DECKS

The cutting height adjustment lever (A, Figure 6) controls

the mower cutting height and has five positions. The

highest cutting position should be used when transport-

ing to and from the work site (do not cut with the lever in

the highest position). The lower four positions are used

when mowing.

Set this lever so that the deck is cutting off 1/3 the height

of the grass or less.

If the desired cutting height falls between two notches,

use the cutting height fine tuning adjuster (B) to achieve

the correct height.

ADJUSTING MOWER CUTTING

HEIGHT - 38”, 44”, 50”, & 54” MOWER

DECKS

The cutting height adjustment knob (B, Figure 8) controls

the mower cutting height. The cutting height is infinitely

adjustable between approximately 1” and 3-5/8” (2,5-

9,2cm). Turn the knob clockwise to raise the deck and

counterclockwise to lower it.

Figure 8. Raising & Lowering Mower

A. Mower Lift Lever

B. Mower Height Adjuster

Not for

Reproduction

MOWER DECK REMOVAL &

INSTALLATION

Lift Link Models

Operating the Tractor

Removing the Mower Deck

1. Park tractor on a hard, level surface such as a con-

crete floor. Turn off PTO switch and engine, remove

the key and apply parking brake.

2. Place mower in the lowest cutting position using the

mower height adjuster.

3. Place the attachment lift in the lowest position.

4. Disconnect the mower lift arm (A, Figure 9) from the

tractor lift arm (B). Re-install washer (C) and safety

clip (D).

5. Remove belt from PTO pulley (B, Figure 10).

6. Turn wheels straight ahead. Pull back on spring-

loaded lever (B, Figure 11) and lift mower hitch off of

the tractor brackets.

7. Turn wheels fully left, and slide mower deck out right

side of tractor.

WARNING

Engage parking brake, disengage PTO, stop

engine and remove key before attempting to

install or remove the mower.

Figure 9. Lift Arms

(Viewed from underneath right side of tractor)

A. Mower Lift Arm C. Flat Washer

B. Tractor Lift Arm D. Safety Clip

Figure 10. Removing & Installing Belt

A. Idler Arm

B. PTO Pulley

CAUTION

The muffler and surrounding areas may be hot.

Not for

Reproduction

Operating the Tractor

Figure 11. Mower Hitch

A. Tractor Hitch Brackets

B. Spring-Loaded Lever

Installing the Mower Deck

1. Park tractor, shut off PTO and engine, remove the

key and apply parking brake. Turn the wheels fully to

the left.

2. Place mower height adjuster (B, Figures 7 & 8) in the

lowest cutting position. Place the mower lift lever in

the lowest position, also. Slide mower deck under

right side of tractor so that mower hitch is aligned

with the front tractor hitch.

3. See Figure 11. Turn wheels straight. Pull back on

the spring-loaded lever (B) while lifting up on the

mower hitch. Install mower hitch onto tractor hitch

brackets (A). When properly installed, the spring-

loaded lever should seat fully underneath the brack-

ets.

4. See Figure 9. Connect the mower lift arm (A) to the

tractor lift arm (B) using the flat washer (C) and safety

clip (D).

5. See Figure 10. Move idler arm (A) to relieve belt ten-

sion. Install belt onto the PTO pulley (B).

Not for

Reproduction

Removing the Mower Deck

1. Park the tractor, fully lower the attachment lift, turn off

the PTO, turn off the engine, remove the key, and

engage the parking brake. If equipped, pivot the

gauge wheels into sliding position (see Figure 13).

2. Place mower in the lowest cutting position using the

mower height control.

3. Use the idler arm (D, Figure 14) to release tension on

the PTO belt, and remove belt from the PTO pulley.

4. Pull down on the lift hooks (A, Figure 14) and unhook

the lift chains (B).

5. Turn the wheels straight ahead. Pull back on spring-

loaded lever (B, Figure 15) and lift mower hitch off of

the tractor brackets (A).

6. Turn wheels fully left, and slide mower deck out from

under the right side of the tractor.

Operating the Tractor

WARNING

Engage parking brake, disengage PTO, stop

engine and remove key before attempting to

install or remove the mower.

Muffler and surrounding areas may be hot.

Figure 12. Raising & Lowering Mower

A. Attachment Lift - Manual

B. Attachment Lift - Hydraulic

C. Cutting Height Control

Figure 13. Gauge Wheels - 54” Models Only

Figure 14. Mower Lift

A. Lift Hook C. PTO Belt

B. Lift Chain D. Idler Arm

MOWER DECK REMOVAL &

INSTALLATION

Chain Lift Models

Not for

Reproduction

Operating the Tractor

Figure 15. Mower Hitch

A. Tractor Hitch Brackets

B. Spring-Loaded Lever

Installing the Mower Deck

NOTE: Perform mower installation on a hard, level sur-

face such as a concrete floor.

1. Park the tractor, fully lower the attachment lift, turn off

the PTO switch, turn off the engine, remove the key,

and engage the parking brake. Turn the wheels fully

to the left.

2. Place mower in the lowest cutting position using the

mower height adjuster. Slide the mower deck under

the right side of tractor so that the mower hitch is

aligned with front tractor hitch (A, Figure 15).

3. See Figure 15. Turn wheels straight. Pull back on

the spring-loaded lever (B) while lifting up on the

mower hitch. Install the mower hitch onto tractor hitch

brackets (A). When properly installed, the spring-

loaded lever should seat fully underneath the brack-

ets (A).

4. See Figure 14. Connect the mower lift chains (B) to

the the tractor lift hooks (A).

NOTE 50” & 54” Mowers: The four-link lift chain is bolted

to the mower deck using the third link. This is correct for

most mowing applications. If mowing ditches or other

surfaces that require the mower to travel below its nor-

mal range, use the fourth link.

5. See Figure 14. From left side of tractor, use the idler

arm (D) to relieve belt tension. Install belt (C) onto the

PTO pulley.

6. If equipped, raise the attachment lift and rotate the

front gauge wheels (Figure 13) into cutting position.

ATTACHING A TRAILER

The maximum horizontal drawbar force allowed is 444

Newton. The maximum vertical drawbar force is 222

Newton. This equates to a 396 lbs (180 kg) trailer on a

10 degree hill. Secure the trailer with an appropriately

sized clevis pin (A, Figure 16) and clip (B).

STORAGE

Before you store your unit for the off-season, read the

Maintenance and Storage instructions in the Safety

Rules section, then perform the following steps:

• Disengage the PTO, set the parking brake, & remove

the key.

WARNING

Never store the unit (with fuel) in an enclosed,

poorly ventilated structure. Fuel vapors can

travel to an ignition source (such as a furnace,

water heater, etc.) and cause an explosion.

Fuel vapor is also toxic to humans and animals.

• Perform engine maintenance and storage measures

listed in the engine owner’s manual. This includes

draining the fuel system, or adding stabilizer to the

fuel (do not store a fueled unit in an enclosed struc-

ture - see warning).

• Battery life will be increased if it is removed, put in a

cool, dry place and fully charged about once a month.

If the battery is left in the unit, disconnect the nega-

tive cable.

Before starting the unit after it has been stored:

• Check all fluid levels. Check all maintenance items.

• Perform all recommended checks and procedures

found in the engine owner’s manual.

• Allow the engine to warm up for several minutes

before use.

(180kg)

396 Lbs.

10˚

3'4"

(1m)

20' (6m)

Figure 16. Trailer Weight Recommendations

A. Clevis Pin

B. Clip

Not for

Reproduction

Page is loading ...

Simplicity 1694010 User manual

Brand: Simplicity

Model: 1694010

Category: Lawnmowers

Type: User manual

Download PDF

report

Simplicity 1694010 User manual

Simplicity 1694010 User manual

Related papers

Other documents