Aruba AP-205H-MNT1 Installation guide

Aruba
Brand
Aruba
Model
AP-205H-MNT1
Type
Installation guide

Aruba AP-205H-MNT1 is a wall mount kit compatible with standard single gang wall boxes. It allows for easy and secure installation of the AP-205H access point, providing a flexible mounting option for various indoor environments. The wall mount features two sets of holes to accommodate both worldwide and US single gang wall boxes, ensuring compatibility with different electrical standards.

With the Aruba AP-205H-MNT1, you can conveniently mount your AP-205H access point on a wall, enabling optimal placement for wireless coverage and signal distribution.

Aruba AP-205H-MNT1 is a wall mount kit compatible with standard single gang wall boxes. It allows for easy and secure installation of the AP-205H access point, providing a flexible mounting option for various indoor environments. The wall mount features two sets of holes to accommodate both worldwide and US single gang wall boxes, ensuring compatibility with different electrical standards.

With the Aruba AP-205H-MNT1, you can conveniently mount your AP-205H access point on a wall, enabling optimal placement for wireless coverage and signal distribution.

AP-205H-MNT1 Wall Mount Kit
Installation Guide
0511762-01 | March 2015 1
Package Contents
Plastic Single Gang Wall Box Mount Bracket
(x2) #6-32 Machine Screws
T8H Torx Security Screw
AP-205H-MNT1 Wall Mount Kit Installation Guide
Introduction
The AP-205H-MNT1 Wall Mount Kit is a spare wall mount bracket that is packaged with the AP-205H access
point. This mounting kit is compatible with standard single gang wall boxes.
Installing the AP-205H-MNT1 Wall Mount Kit
Use the following instructions to install the AP-205H-MNT1 Wall Mount Kit.
1. If the wall box is not already exposed, unscrew and remove the existing wall plate, as shown in Figure 1.
Figure 1 Removing Existing Wall Plate
2. Detach any RJ45 cables by unclipping the connectors from the wall plate, or cutting/removing the UTP
cable(s).
3. Use a short Ethernet cable (sold separately, part number AP-CBL-ETH10) to connect the E0 port to an
RJ45 connector, or crimp an RJ45 plug (not supplied) to the cable and insert into the E0 port. Do the
same for the PT port if used.
4. Align the wall mount with the holes on your single gang wall box. The wall mount contains two sets of
holes to accommodate standard worldwide (Figure 2) and US (Figure 3) single gang wall boxes.
The applicable standards for the wall boxes are:
Worldwide: IEC 60670-1, GB17466, BS4662, and DIN49073
US: ANSI/NEMA OS 1 and OS 2
2 AP-205H-MNT1 Wall Mount Kit | Installation Guide
Figure 2 Attaching Wall Mount to Gang Wall Box (Worldwide Single Gang Outlet Box Shown)
Figure 3 Attaching Wall Mount to Wall Gang Box (US Single Gang Outlet Box Shown)
5. Remove the #6-32 machine screws from their bag and screw the mount onto the wall box, as shown in
Figure 2 and Figure 3.
6. Connect any required cables to the rear of the AP.
7. Align the mounting slots on the back of the AP-205H with the corresponding posts on the wall mount, as
shown in Figure 4.
AP-205H-MNT1 Wall Mount Kit | Installation Guide 3
Figure 4 Securing AP-205H to Mount
8. Push the AP against the holes and then downward until the posts engage the slots at the top of the
mounting holes.
9. (Optional) Once the AP is fastened onto the wall mount, insert the T8H Torx security screw into the hole
located at the upper-right side of the mount and tighten.
10. (Optional) If not using PoE, connect the AC-DC power adapter to the DC power socket located on the
right side of the AP-205H (AP-AC-48V36 sold separately).
  • Page 1 1
  • Page 2 2
  • Page 3 3

Aruba AP-205H-MNT1 Installation guide

Aruba
Brand
Aruba
Model
AP-205H-MNT1
Type
Installation guide

Aruba AP-205H-MNT1 is a wall mount kit compatible with standard single gang wall boxes. It allows for easy and secure installation of the AP-205H access point, providing a flexible mounting option for various indoor environments. The wall mount features two sets of holes to accommodate both worldwide and US single gang wall boxes, ensuring compatibility with different electrical standards.

With the Aruba AP-205H-MNT1, you can conveniently mount your AP-205H access point on a wall, enabling optimal placement for wireless coverage and signal distribution.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents