Anchor Tourvox Quick start guide

Brand: Anchor

Model: Tourvox

Type: Quick start guide

BASIC SYSTEM OPERATION BATTERY INSTALLATION

1. Position the TourVox with the front/speaker facing toward your audience

2. Connect MIC-50 or HBM-50 microphone to the 1/4“

MIC jack

3. Turn the TourVox POWER/VOLUME LEVEL knob on. The red POWER LED will

light and remain lit during operation

4. Set the microphone power switch to ON

5. Adjust the volume with the Power/Volume Level thumb-wheel

POWER INPUT JACK

CHARGE LIGHT

POWER LIGHT

1. Remove the battery compartment cover located on the back of the TourVox

by unscrewing the thumbscrew

2. Slide out the battery pack from the TourVox battery compartment

3. Insert ten ‘AA’ size batteries

(alkaline or RC-30 rechargeable batteries)

into

the battery pack - rechargeable batteries are recommended. Position the ten

batteries into the battery pack by following

the polarity labels on the battery pack

4. Slide in the battery pack into the battery

compartment and push the battery pack all

the way into compartment

5. Replace the battery compartment cover and

tighten the thumbscrew

NOTE: PA System CAN Be Used While Charging!

For applications where the TourVox PA system is used frequently, the RC-30 rechargeable

battery kit is available. This kit includes 10 rechargeable NiMH batteries and an AC charging

adapter. When fully charged, the batteries provide approximately 10 - 12 hours of operation.

NOTE: New batteries must be charged for at least 6 hours prior to first use.

MICROPHONE

INPUT

TourVox Top

RECHARGEABLE BATTERY KIT

Optional accessory

POWER/

VOLUME LEVEL

TourVox Side

BATTERY

COMPARTMENT

For extended battery life, we recommend you fully charge the batteries once each month during

periods of infrequent use. Always fully recharge batteries before storing.

1. Install the 10 rechargeable NiMH batteries into the TourVox (See Battery Installation)

2. Insert the charger plug into the Power Input Jack labeled DC IN on the TourVox side panel

3. Plug the AC adapter into a power outlet for 4 - 6 hours to fully charge

CAUTION: NEVER recharge other types of batteries. Doing so can result in battery

explosion. Use only rechargeable Nickel-Metal Hydride (NiMH) batteries.

Using the Rechargeable Battery Kit (RC-30)

Cycling the Batteries

HAVING TROUBLE WITH YOUR PA SYSTEM?

CONDITION POSSIBLE SOLUTIONS

No Sound

(Power LED: OFF)

• Turn POWER switch ON

• Charge batteries

No Sound

(Power LED: ON)

• Make sure mic cable is completely plugged in

• Turn microphone volume on

Shortened Battery Life

• Replace batteries and fully charge new batteries before use

• ‘Cycle’ NiMH batteries

Distorted Sound

• Lower system volume

• Replace or recharge batteries

Unit Turns On & Off During Use • Replace rechargeable batteries

QUICK START MANUAL

For a complete Owner’s Manual, visit anchoraudio.com

Please check your new unit carefully for any damage which may have

occurred during shipment.

*Please keep the product box(es) that your Anchor Audio product(s) was shipped in, so

it is available in the event the product(s) need to be shipped back to Anchor Audio for

any reason.

100-0311-000 REV B

NEED MORE HELP?

anchoraudio.com | 800.262.4671

TECHNICAL SPECIFICATIONS

Rated Power Output 30 watts

Max SPL @ Rated Power 100 dB @ 1 meter

Frequency Response 100 Hz - 15 kHz ± 3 dB

Microphone Input 1/4“ phone, Lo-Z

Speaker Type 4“ neodymium

Battery Type 10 ‘AA’ alkaline

Dimensions (HWD) 7“ x 6“ x 3.5“ (17.8 x 15.2 x 8.9 cm)

Weight 2.5 lbs / 0.45 Kg

RC-30 - Recharge Kit (optional)

Battery Type 10 ‘AA’ size, NiMH 2.5 AH

Charger AC-30

AC-30 Input 120 VAC, 60 Hz, 24 watts max

AC-30/220 Input 220 VAC, 50 Hz, 10 watts max

TOURVOX

Anchor Tourvox Quick start guide

Anchor Tourvox Quick start guide

Anchor Tourvox Quick start guide

Related papers

Other documents